Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 20 de 122
Filtrar
1.
Braz. j. oral sci ; 23: e243158, 2024. ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1527026

RESUMO

Aim: In recent years, great advances have been made in the use of CAD/CAM to prepare fixed restorations. The marginal and internal fit of these restorations is a principal determinant for their clinical success. In addition, the nature of the oral environment affects the mechanical properties of these restorations. Therefore, this study aimed to investigate the effect of aging process under conditions that simulate the oral environment on the marginal adaptation, and, fracture resistance of crowns fabricated from polyether ether ketone (PEEK) using CAD/CAM methods. Methods: Twenty identical crown restorations were fabricated by using CAD/CAM methods to mill polyether ether ketone (PEEK) material. These crowns were produced by using a software design of an epoxy resin replica of the prepared maxillary first premolar tooth. All PEEK crowns were cemented and randomly divided into two equal groups (A, B). Each group was divided into subgroups (A1, A2 and B1, B2). Group A1 and A2 were used to measure marginal adaptation and fracture resistance, respectively, before aging, while group (B1 and B2) were measured after aging. The cemented crowns were mounted in resin molds to facilitate the sectioning process. The measurements of the marginal gap were performed after sectioning at four points using a stereomicroscope. The fracture resistance of the crowns was investigated using a universal testing machine. A statistical analysis was performed using the GraphPad Prism® software version and unpaired Student's t-test. Results: The results revealed that aging affected the marginal gap, and the fracture resistance of the PEEK crowns. While aging, negatively affected the conditions under investigation, however the least significant difference of marginal gap was found in the margin region. Conclusions: PEEK-CAD/CAM is considered as a good alternative prosthodontic material for fixed prostheses. The CAD/CAM technique used to make PEEK crown restorations in our study offers the advantages of high marginal accuracy and fracture resistance for long-term performance in the oral environment


Assuntos
Polímeros , Envelhecimento , Desenho Assistido por Computador , Adaptação Marginal Dentária , Coroas , Resistência à Flexão , Cetonas
2.
Odovtos (En linea) ; 25(1)abr. 2023.
Artigo em Inglês | LILACS, SaludCR | ID: biblio-1422193

RESUMO

The aim of this in vitro study was to evaluate the biomechanical and chemical behavior of various bioactive materials in class II MOD restorations. Forty- eight standardized class II MOD cavities were prepared in sound extracted human molar teeth. The specimens were divided into four groups according to the restorative material: Group 1 (Filtek™ Z350 XT), Group 2 (Biodentine™ as a liner, and then restored with Filtek™ Z350 XT), Group 3 (Cention N™), and Group 4 (Activa™ Bioactive-Restorative). The samples were tested for fracture resistance by subjecting them to a compressive load in a Universal testing Machine. The failure modes of each specimen were evaluated. The alkalinizing potential and calcium ion release of the materials were measured. SEM-EDAX analyses were also performed for all materials. Data were analyzed using ANOVA and post hoc Tukey test (p<0.05). Group 1 showed the higher fracture resistance (p<0.05). Group 3 had greater fracture resistance values but no statistical difference from Group 4. Biodentine™ showed greater biomineralization potential. Class II MOD restorations of Group 1 displayed the higher fracture resistance; however, it was highly associated with catastrophic failure. Conversely, Biodentine™ presented a more significant bioactivity potential, and its use, as in Group 2, promoted the most favorable failure mode.


El objetivo de este estudio, in vitro, fue evaluar el desempeño biomecánico y químico de varios materiales bioactivos en restauraciones clase II MOD. Se prepararon cuarenta y ocho cavidades clase II MOD estandarizadas en dientes molares humanos extraídos. Las muestras se dividieron en cuatro grupos según el material de restauración: Grupo 1 (Filtek™ Z350 XT), Grupo 2 (Biodentine™ como base y luego restaurado con Filtek™ Z350 XT), Grupo 3 (Cention N™) y Grupo 4 (Activa™ Bioactivo-Reparador). La prueba de resistencia a la fractura fue realizada en una máquina de ensayo universal Instron. Se evaluaron los modos de falla de cada espécimen. Se midió el pH y la liberación de iones de calcio de los materiales. Se realizaron análisis SEM-EDAX. Los datos se analizaron mediante ANOVA y la prueba post hoc de Tukey (p<0,05). El grupo 1 mostró la mayor resistencia a la fractura (p<0,05). El Grupo 3 tuvo mayores valores de resistencia a la fractura que el Grupo 4, pero sin diferencia estadística. Biodentine™ mostró un mayor potencial de biomineralización. Las restauraciones Clase II MOD del Grupo 1 mostraron la mayor resistencia a la fractura; sin embargo, estuvo altamente asociado con fallas irreparables. Por el contrario, Biodentine™ presentó un potencial de bioactividad más significativo y su uso, como en el Grupo 2, promovió el modo de falla más favorable.


Assuntos
Materiais Biomédicos e Odontológicos/análise , Resinas Compostas/análise , Resistência à Flexão
3.
Braz. j. oral sci ; 22: e231377, Jan.-Dec. 2023. tab, ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1519248

RESUMO

The aim of this study was to investigate the influence of the quantity and positioning of feldspathic ceramic specimens inside the furnace on their flexural strength and translucency. The tested hypotheses were that the arrangement of specimens in the furnance would not influence 1) the translucency or 2) the biaxial strength of the porcelain. Methods: Ninety porcelain specimens were made (1.2 mm thickness and 13.5 mm diameter) and assigned into two main groups (n=15): G1 group - 15 firing cycles containing only one specimen each, always at the center of the refractory; and G5 group - 15 firing cycles containing five specimen each, where one specimen was at the center of the refractory and four specimens positioned equidistantly on the periphery. The translucency test was performed using a spectrophotometer, followed by the flexural strength test, according to ISO 6872:2015. T-student test was performed for both the mechanical and optical obtained data. Results: The flexural strength of the porcelain was not affected by the positioning (center x periphery) of the specimens inside the furnace (p =0.08), but the translucency was affected (periphery > center; p =0.009). Regarding to the number of feldspathic ceramic specimens, the biaxial flexural strength was affected (p =0.025), as well as the translucency (p <0.05). Conclusion: A higher quantity of feldspathic ceramic specimens for each firing cycle decreased its biaxial flexural strength and translucency. Also, specimens positioned at the center of the refractory became less translucent than those positioned at the periphery.


Assuntos
Humanos , Termodinâmica , Porcelana Dentária/química , Absorção Fisico-Química , Resistência à Flexão , Luz , Espectrofotometria , Temperatura , Teste de Materiais , Microscopia Eletrônica de Varredura , Fractografia
4.
Braz. dent. sci ; 26(4): 1-8, 2023. ilus, tab
Artigo em Inglês | BBO - Odontologia, LILACS | ID: biblio-1512140

RESUMO

Objective: To evaluate the biaxial flexural strength (BFS) of lithium disilicate (L), cemented on different substrates (epoxy resin - E and metal - M) with dual-cure resin cement (Rc) and zinc phosphate cement (Zc), not aged, thermally aged (TC) or thermo-mechanical aged (TC/MC). Material and Methods: Disks of L, E, and M were fabricated, and the cementation was performed according to the following groups: ERc (L+E+Rc); MRc (L+M+Rc); MZc (L+M+Zc); EZc (L+E+Zc). Ten samples from each described group were tested in BFS, ten more samples were subjected to TC (1×104 cycles between 5 ºC and 55 ºC water), and the last 10 samples were subjected to TC/MC (MC: 1.2×106 cycles, 50 N, 3.8 Hz). The BFS test was performed and scanning electron microscopy (SEM) was performed to evaluate the failure mode. The effect of the cementation strategy (cement/substrate) was compared in each aging method and the effect of the aging method was evaluated for each cementation strategy by one-way ANOVA and Tukey post-hoc test (α=0.05). Results: The strength values were highest to M (237.8 ~ 463.9 MPa), in comparison to the E (41.03 ~ 66.76 MPa), despite aging and luting agent. Flexural strength data decreased after TC and TC/MC in groups cemented with Zc, but was stable when cemented with Rc. SEM analysis indicated that failure origins were located at the tensile surface of the L. Conclusion: Lithium disilicate discs cemented to the metallic substrate presented the highest biaxial flexural strength. The cementation with dual-cure resin cement did not decrease BFS after aging (AU)


Objetivo: Avaliar a resistência à flexão biaxial (BFS) do dissilicato de lítio (L), cimentado sobre diferentes substratos (resina epóxi - E e metal - M) com cimento resinoso dual (Rc) e cimento de fosfato de zinco (Zc), não envelhecido, submetido ao envelhecido térmico (TC) ou ao envelhecido térmico-mecânico (TC/MC). Material e Métodos: Foram confeccionados discos de L, E e M, e a cimentação foi realizada de acordo com os seguintes grupos: ERc (L+E+Rc); MRc (L+M+Rc); MZc (L+M+Zc); EZc (L+E+Zc). Dez amostras de cada grupo descrito foram testadas em BFS, mais dez amostras foram submetidas à TC (1×104 ciclos de imersão em água entre 5 ºC e 55 ºC), e as últimas 10 amostras foram submetidas à TC/MC (MC: 1.2 ×106 ciclos, 50 N, 3.8 Hz). Foram realizados os testes de BFS e a microscopia eletrônica de varredura (MEV) para avaliar o modo de falha. O efeito da estratégia de cimentação (cimento/substrato) foi comparado em cada método de envelhecimento e o efeito do método de envelhecimento foi avaliado para cada estratégia de cimentação por ANOVA a um fator e teste post-hoc de Tukey (α=0,05). Resultados: Os valores de resistência foram maiores para M (237.8 ~ 463.9 MPa), em comparação com E (41.03 ~ 66.76 MPa), independentemente do envelhecimento e do agente cimentante utilizado. Os dados de resistência à flexão diminuíram após TC e TC/MC nos grupos cimentados com Zc, mas se mantiveram estáveis quando cimentados com Rc. A análise MEV indicou que a origem das falhas estava localizada na superfície de tração do L. Conclusão: Os discos de dissilicato de lítio cimentados ao substrato metálico apresentaram maior resistência à flexão biaxial. A cimentação com cimento resinoso dual não diminuiu o BFS após o envelhecimento (AU)


Assuntos
Envelhecimento , Cimentação , Resistência à Flexão
5.
Braz. j. oral sci ; 22: e238439, Jan.-Dec. 2023. tab
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1512207

RESUMO

Various forms of temporary resins are offered on the market; however, the properties of temporary resins obtained by milling and 3D printing have not been fully examined. This study aimed to compare the flexural strength and Vickers hardness of milled and 3D-printed resins. Methods: Three resins were tested: Evolux PMMA (milled resin), Cosmos Temp (3D-printed resin), and Structur 2 SC (bis-acrylic resin, group control). Specimens were prepared with rectangular shapes (n = 12) for flexural strength measurements and disc shapes (n = 9) for Vickers hardness tests. Flexural strength tests were performed at a crosshead speed of 0.75 mm/min, and the Vickers hardness was measured under a load of 20 N for 10 s. The obtained data were subjected to the Kruskal­Wallis test. Results: A significant difference (p < 0.05) in flexural strength was observed among the three sample groups: Evolux PMMA (111.76 MPa), Structur 2 SC (87.34 MPa), and Cosmos Temp (56.83 MPa). No significant difference (p < 0.05) was observed between the Vickers hardness values of Structur 2 SC (33.37 VHN) and Evolux PMMA (29.11 VHN); however, both materials were statistically superior to Cosmos Temp (10.90 VHN). Conclusion: While the mechanical properties of the milled resin were superior or similar to those of the bisacrylic resin, the 3D-printed resin was statistically inferior to both the milled and bis-acrylic resins


Assuntos
Desenho Assistido por Computador , Restauração Dentária Temporária , Resinas , Resistência à Flexão , Testes de Dureza
6.
Pesqui. bras. odontopediatria clín. integr ; 23: e210155, 2023. tab, graf
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1507020

RESUMO

ABSTRACT Objective: To evaluate the mechanical properties of mini-implants (MIs) manufactured from stainless steel and compare them with conventional titanium-aluminum-vanadium alloy MIs. Material and Methods: The following groups were formed: G1 (n=24), 8×1.5 mm steel MIs; G2 (n=24), 12×2.0 mm steel MIs; and G3 (n=24), 10×1.5 mm titanium MIs. The 72 MIs were inserted in the infra zygomatic crest region of the maxilla and retromolar trigone in the jaw of 10 pigs. Pull-out, insertion torque, fracture and percussion tests were performed in order to measure the tensile strength, primary stability and fracture strength of MIs. A digital torque gauge was used to measure insertion and fracture torque, a universal mechanical testing machine was used for pull-out testing and a periotest device was used to measure the micromovement of MIs. For morphological and MI component evaluation, scanning electron microscopy (SEM) was performed. D'Agostino & Pearson, Kruskal-Wallis, and Dunn post-hoc and normality tests were used. Results: G2 insertion and fracture torques were significantly higher than G1 and G3 insertion and fracture torques (p<0.05). The pull-out and percussion tests presented similar values among the groups. SEM revealed that the fracture point was predominantly on the fourth thread for steel MIs (G1 and G2) and on the seventh thread for titanium-aluminum-vanadium MIs (G3). Conclusion: The mechanical properties of stainless steel MIs are superior to those of titanium-aluminum-vanadium alloy MIs.


Assuntos
Animais , Aço Inoxidável/química , Resistência à Tração , Titânio , Procedimentos de Ancoragem Ortodôntica/instrumentação , Suínos , Microscopia Eletrônica de Varredura/instrumentação , Estatísticas não Paramétricas , Resistência à Flexão , Testes Mecânicos
7.
Pesqui. bras. odontopediatria clín. integr ; 23: e210059, 2023. tab, graf
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1529136

RESUMO

ABSTRACT Objective: To identify the tobacco effect on flexural properties and the microhardness of three acrylic resins. Material and Methods: Three resins were tested: two thermo-polymerizable acrylic resins (RMB 20 and BMS 014) and one autopolymerized acrylic resin. The 3-point bending and microhardness tests were carried out with a universal tensile-compression machine and a micro-Vickers hardness tester. The acrylic resin specimens have been exposed for 21 days to cigarette smoke in a smoking room. Their mechanical strength was compared to unexposed samples. Statistical analysis was performed using the data processing software SPSS Statistics 21.0. Results: The flexural properties of the resins were affected by cigarette smoke only in the case of Major Base 20® (drop in strength with p= 0.02; 0.6; 0.7 and in elastic modulus with p= 0.86; 0.74 and 0.85 for Major Base 20®, BMS 014® and Major Repair®). The cigarette smoke affected significantly microhardness for all groups (p<0.001). Conclusion: Cigarette smoking does not affect the flexural properties of the acrylic resin (BMS 014® and Major Repair® unlike Major Base 20®), but it does reduce the microhardness.


Assuntos
Dentaduras , Fumar Cigarros/efeitos adversos , Resistência à Flexão , Propriedades de Superfície , Análise de Variância
8.
Braz. j. oral sci ; 22: e237338, Jan.-Dec. 2023. ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1397295

RESUMO

Aim: Endocrown restorations are commonly used to rehabilitate endodontically treated posterior teeth and their use is well-founded in these cases. However, to date, there is little scientific evidence of their behavior in anterior teeth. The aim of this in vitro study was to evaluate the compressive strength of upper central incisors teeth, restored with glass-ceramic total crowns by the conventional anatomical core technique, and compare them to teeth restored with endocrowns with and without the presence of ferrule. Methods: Thirty teeth were randomly distributed into three groups: GE2 - endocrown group with 2 mm ferrule, GE0 - endocrown group without a ferrule, and GC - conventional crown with intraradicular post group. Crowns were cemented and teeth submitted to the 45o compression test until the fracture happened. Fractured specimens were analyzed to determine the fracture pattern. Descriptive analysis of the variables was performed and one-way analysis of variance was utilized to analyze the data for significant differences at p < 0.05. Results: The results of the control group (284.5 ± 201.05N) showed the highest fracture resistance value, followed by the 2mm group (274.54 ± 199.43N) and by the 0mm group (263.81 ± 80.05N). There was no statistically significant difference between all the groups (p = 0.964). Conclusions: The absence of a cervical enamel necklace favored a debonding of the pieces and endodontically treated anterior teeth could be restored with endocrown, which could be considered a conservative and viable treatment option


Assuntos
Desenho Assistido por Computador , Coroas , Endodontia , Resistência à Flexão
9.
Rev. odontol. UNESP (Online) ; 52: e20230006, 2023. tab, ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1442091

RESUMO

Introduction: with the technological advance in dentistry, light-polymerized three-dimensional (3D) printing resins had become an alternative for the manufacture of occlusal splint splints. Objective: the present study aimed to analyze the flexural strength of a resin for 3D printing compared to conventional acrylic resins (chemically activated and thermally activated), under the influence of thermocycling. Material and method: 60 specimens were made, which were distributed in six experimental groups (n = 10), according to the resin employed (chemically activated acrylic resin, thermally activated acrylic resin and 3D printing resin) and the treatment received (control and thermocycling). The specimens were submitted to flexural strength by the three-point flexural test. Result: data analysis showed that the material factor (<0.0001) and the thermocycling factor (p = 0.0096) influenced flexural strength, however, the interaction between the two factors did not (p = 0.9728). Conclusion: it was concluded that 3D printing resins presented the lowest flexural resistance to acrylic resins, especially when submitted to thermocycling.


Introdução: com o avanço tecnológico dentro da odontologia, as resinas fotopolimerizáveis para impressão tridimensional (3D) se tornaram uma alternativa para a fabricação de dispositivos interoclusais. Objetivo: o presente trabalho teve como objetivo analisar a resistência flexural de uma resina para impressão tridimensional comparada com resinas acrílicas convencionais (quimicamente ativada e termicamente ativada), sob a influência da termociclagem. Material e método: foram confeccionados 60 corpos de prova, que foram distribuídos aleatoriamente em seis grupos experimentais (n=10), de acordo com a resina utilizada (resina acrílica ativada quimicamente, resina acrílica ativada termicamente e resina para impressão 3D) e com o tratamento recebido (controle e termociclagem). Os corpos de prova foram submetidos ao ensaio de flexão de três pontos para determinação da resistência flexural. Resultado: a análise dos dados demonstrou que o fator material (<0.0001) e o fator termociclagem (p=0.0096) influenciaram a resistência flexural, entretanto, a interação entre os dois fatores não (p=0.9728). Conclusão: deste modo podemos concluir que a resina para impressão 3D apresentou desempenho inferior às resinas acrílicas, especialmente quando submetida a termociclagem.


Assuntos
Resinas Acrílicas , Placas Oclusais , Resinas , Impressão Tridimensional , Resistência à Flexão
10.
Braz. j. oral sci ; 22: e239056, Jan.-Dec. 2023. ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1443592

RESUMO

Aim: This review investigated the effect of applying an adhesive after surface treatment of glass-ceramics on the bonding, mechanical or clinical behavior. Methods: Studies comparing the adhesive, mechanical or clinical behavior of glass-ceramics, with or without adhesive application after surface treatment, were included. Searches were performed in PubMed, Scopus, and Web of Sciences databases (January 2022), resulting in 15 included studies. Results: Regarding the evaluated outcomes, 13 studies assessed bond strength, 2 studies assessed biaxial flexural strength and 1 study assessed fatigue failure load, while no study evaluating clinical outcomes was included. It was possible to observe that the adhesive application after ceramic surface treatment was unfavorable or did not influence the evaluated outcomes. Conclusion: Most of the evidence available in the literature shows that the adhesive application after surface treatment does not improve the adhesive and mechanical behavior of glass-ceramics


Assuntos
Cerâmica , Cimentos Dentários , Resistência à Flexão
11.
Braz. j. oral sci ; 21: e226036, jan.-dez. 2022. ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1393321

RESUMO

Dental implants could give back function, esthetics and quality of life to patients. The correct choice of the implant, especially in borderline cases, is essential for a satisfactory result. Aim: Thus, the objective of this study was to evaluate the mechanical behavior of Morse taper implants with two different prosthetic interfaces. Methods: Twenty self-locking Morse taper implants, 2.9 mm in diameter (FAC), and 20 Morse taper implants, 3.5 mm in diameter (CM) were divided into two groups (n=10), and submitted to strength to failure test, optical microscopic evaluation of fracture, metallographic analysis of the alloy, finite element analysis (FEA) and strain gauge test. A Student's t test (α = 0.05) was made for a statistical analysis. Results: For the strength to failure test, a statistically difference was observed (p <0.001) between FAC (225.0 ± 19.8 N) and CM (397.3 ± 12.5 N). The optical microscopic evaluation demonstrated a fracture pattern that corroborated with FEA ́s results. The metallographic analysis determined that the implants of the FAC group have titanium-aluminum-vanadium alloy in their composition. In the strain gauge test, there was no statistical difference (p = 0.833) between CM (1064.8 ± 575.04 µS) and FAC (1002.2 ± 657.6 µS) groups. Conclusion: Based on the results obtained in this study, ultra-narrow implants (FAC) should ideally be restricted to areas with low masticatory effort


Assuntos
Resistência à Tração , Implantação Dentária , Resistência à Flexão
12.
Braz. j. oral sci ; 21: e225757, jan.-dez. 2022. ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1366215

RESUMO

Aim: This study aimed to evaluate the effect of frozen storage on the physical properties of a silicone-based test food material, highly used to evaluate the masticatory performance in research settings. Methods: A total of 1,666 silicone cubes of Optosil Comfort® with 5.6-mm edges were shaped and stored at -18°C. The cubes were subsequently tested for flexural strength (maximum force, displacement, stress, and strain) before breaking (n = 136), changes in weight and size (n = 170), and masticatory performance (n = 1360) at eight timepoints: immediately after cube preparation (baseline, no freezing), and 1, 2, 3 and 4 weeks, and 2, 4 and 6 months after frozen storage. The cubes were thawed 8 h before each assessment. Results: The maximum force, stress, maximum displacement, and deformation values for the cubes were not affected by freezing (P > 0.05). At all of the time points, the cubes exhibited similar weight (P = 0.366) and size (identical values). The masticatory performance for the cubes also showed no differences from baseline through 6 months (P = 0.061). Conclusion: Freezing Optosil Comfort® silicone cubes did not alter the physical and mechanical properties of the material, being suitable to optimize the assessment of masticatory parameters for research purposes


Assuntos
Humanos , Masculino , Adulto , Elastômeros de Silicone , Teste de Materiais/métodos , Congelamento , Resistência à Flexão , Mastigação , Fatores de Tempo
13.
J. oral res. (Impresa) ; 11(6): 1-9, nov. 3, 2022. tab, ilus
Artigo em Inglês | LILACS | ID: biblio-1437585

RESUMO

Background: This study evaluated the effects of using different root canal sealers and protocols for cleaning intraradicular dentin on the bond strength of a composite resin used to reinforce weakened roots. Material and Methods: Sixty-four roots of extracted human maxillary canines were weakened, prepared and filled with two different endodontic sealers (Endofill and AH Plus). In half of the sample, set aside for each respective sealer, excess filling material was cleaned. In the other half, the weakened areas were not cleaned, and the excess of sealer was spread on the intraradicular dentin. Intentionally worn areas inside each root were restored with a microhybrid light-cure composite resin (Z100) to reinforce them, with and without acid etching. Prefabricated metal posts were fixed with a dual resin cement (RelyX ARC), and the specimens were submitted to a pull-out test. Statistical analysis was performed by means of Shapiro-Wilk, analysis of variance (one-way ANOVA) and Tukey-Kramer tests (p<0.05). Results: The groups filled with Endofill (GI, GII, GIII, GIV) had the lowest bond strength values, which were similar among each other (p>0.05).The greatest bond strength values were observed in roots filled with AH Plus (GV, GVI, GVII, GVIII), mainly without cleaning of the weakened areas, and followed by acid etching (GVII), and also with cleaning of the weakened areas, however, with no acid etching (GVI) (p<0.05). Conclusion: The greatest bond strength values were observed in roots filled with AH Plus; (1) without cleaning of the weakened areas and with acid etching, and; (2) with cleaning of the weakened areas, but without acid etching.


Antecedentes: este estudio evaluó los efectos del uso de diferentes selladores de conductos radiculares y protocolos para limpiar la dentina intrarradicular sobre la fuerza de unión de una resina compuesta utilizada para reforzar las raíces debilitadas. Material y Métodos: Sesenta y cuatro raíces de caninos maxilares humanos extraídos fueron debilitadas, preparadas y rellenadas con dos selladores endodónticos diferentes (Endofill y AH Plus). En la mitad de la muestra, reservada para cada sellador respectivo, se limpió el exceso de material de relleno. En la otra mitad, las áreas debilitadas no se limpiaron y el exceso de sellador se esparció sobre la dentina intrarradicular. Las áreas desgastadas intencionalmente dentro de cada raíz se restauraron con una resina compuesta fotopolimerizable microhíbrida (Z100) para reforzarlas, con y sin grabado ácido. Los postes metálicos prefabricados se fijaron con un cemento de resina dual (RelyX ARC) y los especímenes se sometieron a una prueba de extracción. El análisis estadístico se realizó mediante Shapiro-Wilk, análisis de varianza (ANOVA de una vía) y pruebas de Tukey-Kramer (p<0,05). Resultados: Los grupos rellenos con Endofill (GI, GII, GIII, GIV) presentaron los valores más bajos de fuerza de unión, los cuales fueron similares entre sí (p>0,05). Los mayores valores de fuerza de unión se observaron en raíces rellenas con AH Plus (GV, GVI, GVII, GVIII), principalmente sin limpieza de las áreas debilitadas, seguido de grabado ácido (GVII), y también con limpieza de las áreas debilitadas aunque sin grabado ácido (GVI) (p<0.05). Conclusión: Los mayores valores de fuerza de unión se observaron en las raíces rellenas con AH Plus; (1) sin limpieza de las áreas debilitadas y con grabado ácido, y; (2) con limpieza de las áreas debilitadas, pero sin grabado ácido.


Assuntos
Humanos , Materiais Restauradores do Canal Radicular , Adesivos Dentinários , Dentina/efeitos dos fármacos , Resistência à Flexão , Resultado do Tratamento , Cavidade Pulpar/efeitos dos fármacos
14.
Rev. ADM ; 79(5): 284-291, sept.-oct. 2022. tab
Artigo em Espanhol | LILACS | ID: biblio-1428520

RESUMO

Introducción: se realizó una revisión bibliográfica con el objetivo de conocer, analizar y comparar los diferentes tipos de adhesivos de octava generación que se encuentran en el mercado y la diferencia que existe entre cada uno. Los adhesivos universales han demostrado mejoras en su resistencia, sobre todo en las técnicas de aplicación y en las propiedades de estos materiales, al mejorar la fuerza adhesiva para que el odontólogo pueda brindar tratamientos restaurativos exitosos. Objetivo: conocer, analizar y comparar los diferentes tipos de adhe- sivos de la octava generación empleados en odontología. Material y métodos: se realizó una búsqueda en las bases de datos electrónicas PubMed, BVS, Redalyc y ScienceDirect. Se utilizaron 32 artículos que cumplieron con los criterios predeterminados y la especificidad reque- rida para la pregunta de investigación. Conclusiones: se demostró que la tecnología cada día avanza, sobre todo en el área de los adhesivos, ya que éstos son de mucha utilidad en el día a día del odontólogo; es importante conocer cada uno de éstos, puesto que es un poco complejo seleccionar el correcto, mas no el uso. En la actualidad, existen diversas opciones por las que el odontólogo puede optar, es por ello que el pro- fesional debe estar capacitado sobre cada una de las diferentes marcas existentes y, de acuerdo al tratamiento, debe elegir cuál es mejor utilizar en una rehabilitación. Es importante para el odontólogo conocer estos materiales, ya que esto lo beneficiará al momento de llevar un plan de tratamiento restaurador (AU)


Introduction: a bibliographic review was carried out to learn about, analyze, and compare the different types of eighth-generation adhesives on the market and the difference between each one. Universal adhesives have demonstrated improvements in their resistance, especially in the application techniques and properties of these materials, improving the adhesive strength so that the dentist can provide successful restorative treatments. Objective: to know, analyze and compare the different types of eighth-generation adhesives used in dentistry. Material and methods: a search was made of the following electronic databases: PubMed, BVS, Redalyc, ScienceDirect. Finally, 32 articles that met the predetermined criteria and the specificity required for the research question were used. Conclusions: it was demonstrated that technology is advancing every day, especially in the area of adhesives since these are very useful in the daily life of the dentist. It is important to know each one of these since it is a little complex at the moment of selecting the correct one, but not the use. Currently, there are several options that the dentist can choose, which is why the professional must be trained on each of the various existing brands and according to the treatment which is the best to use at the time of rehabilitation. The dentist needs to know these materials since they will benefit him/her when carrying out a restorative treatment plan (AU)


Assuntos
Tecnologia Odontológica/tendências , Adesivos Dentinários , Propriedades de Superfície , Condicionamento Ácido do Dente/métodos , Força Compressiva , Esmalte Dentário/efeitos dos fármacos , Resistência ao Cisalhamento , Dentina/efeitos dos fármacos , Nanopartículas , Resistência à Flexão
15.
Natal; s.n; 28 set. 2022. 70 p. tab, ilus.
Tese em Português | LILACS, BBO - Odontologia | ID: biblio-1532747

RESUMO

O aprimoramento da tecnologia CAD/CAM permitiu a confecção de placas estabilizadoras digitais, no entanto, há lacunas acerca do comportamento desses dispositivos frente a variáveis mecânicas e biológicas ainda desconhecidas. Dessa forma, o objetivo desse trabalho foi verificar se as resinas utilizadas na tecnologia digital das placas fresadas e impressas são capazes de influenciar na resistência à fratura e na adesão de micro-organismos em detrimento das resinas empregadas na confecção das placas termopolimerizáveis convencionais e se as propriedades testadas se relacionam com a variação da espessura desses dispositivos. Para tanto, foi realizado um estudo in vitro que contou com as fases mecânica e microbiológica, sendo cada uma composta pelos grupos Convencional (GC) (n=30), Fresado (GF) (n=30) e Impresso (GI) (n=30), de acordo com o método de confecção, possuindo cada um três subgrupos (n=10) que variaram a espessura dos espécimes de 1 a 3 mm. Na fase mecânica, as amostras, com formato de barras de 65 mm, foram testadas quanto à resistência à fratura na máquina de ensaios universal, com célula de carga de 500 kgf e velocidade de 1 mm/min; na microbiológica, a forma foi de discos com 15 mm de diâmetro, submetidos à adesão de micro-organismos à superfície com a exposição a Streptococcus mutans e mantidos por 24h a 35 °C em estufa para sucessiva contagem de UFC, com controle positivo. Os testes foram feitos em triplicata e os dados foram armazenados no SPSS 22.0 e a análise estatística contou com a ANOVA e o pósteste de Tukey. Nos resultados da fase mecânica, o ANOVA identificou diferenças estatisticamente significativas entre os grupos (p≤0,005), mostrando que GC e GF apresentaram melhores resultados. O pós-teste de Tukey considerou diferença estatisticamente significativa entre GF e GI (p=0,031), elencando GF como superior. Para a fase microbiológica, não foram verificadas diferenças estatísticas entre os grupos (p>0,005) em nenhuma das análises. Observou-se que para a resistência a fraturas, as resinas do modo fresado descreveram resultados superiores e/ou próximos aos da técnica convencional; e que as resinas da técnica digital e convencional, quanto à adesão superficial de micro-organismos, não diferiram entre si (AU).


CAD/CAM technology allowed the stabilizing splints manufacture, however there are gaps about these devices' behavior in face of mechanical and biological variables that are still unknown. Thus, the objective of this project was to verify if the resins used in digital technology of milled and printed stabilizer splints can influence fracture resistance and microorganism adhesion, in detriment of the resin applied in manufacture of conventional thermopolymerizable splints and if the tested properties are related to thickness variation of these devices. The method included mechanical and microbiological steps, each one composed by Conventional (CG) (n=30), Milled (MG) (n=30) and Printed (PG) (n=30) groups, according to the method of preparation, each one having three subgroups (n=10) that varied the specimen thickness from 1 to 3 mm. In the mechanical step, the samples, in the form of 65 mm bars, were tested for fracture resistance in a universal testing machine, with load cell of 500 kgf and speed of 1 mm/min; in the microbiological step, the shape was in form of 15 mm diameter discs, subjected to microorganism adhesion to the surface with exposure to Streptococcus mutans and kept for 24 hours at 35 °C in oven for successive CFU counting, with positive control. The tests were performed in triplicate and data were stored in SPSS 22.0 and statistical analysis used ANOVA and Tukey's post hoc. In the results of mechanical step ANOVA had identified statistically significant differences between the groups (p≤0,005), showing CG and MG had presented better results. Tukey´s post hoc had considered statistically significant difference between MG and PG (p=0,031), listing MG as superior. For the microbiological step, they did not show statistical differences between the groups (p>0.005) in any analysis. It was observed milled resins described superior results and/or close to the conventional technique one, for fracture resistance; and resins of digital and conventional technique, regarding the microorganism adhesion to the surface, did not differ from each other (AU).


Assuntos
Desenho Assistido por Computador/instrumentação , Resistência à Flexão , Adesão Celular , Análise de Variância , Adesões Focais/microbiologia
16.
Rev. Odontol. Araçatuba (Impr.) ; 43(1): 45-50, jan.-abr. 2022. ilus
Artigo em Português | LILACS, BBO - Odontologia | ID: biblio-1361713

RESUMO

O objetivo deste relato de caso foi descrever em detalhes a técnica de transfixação de pino de fibra de vidro no sentido horizontal e restauração de resina composta em um dente molar tratado endodonticamete. Paciente, sexo feminino, 51 anos de idade, buscou o Centro Universitário da Serra Gaúcha (FSG ­ Caxias do Sul ­ Rio Grande do Sul) com a necessidade de realizar tratamento endodôntico do elemento molar número 26. Após a avaliação inicial, foi realizada a endodontia. O elemento havia pouca sustentação das paredes vestibular e palatina, então foi proposto a colocação de pino intrarradicular seguido de coroa, entretanto, por questões financeiras a paciente não aceitou. Logo, foi proposto a técnica de transfixação horizontal de pino de fibra de vidro associado a uma restauração de resina composta de forma direta. O procedimento foi realizado em sessão única e foi utilizado um pino de fibra de vidro número 1 disposto transversalmente entre as paredes mesiopalatina e distovestibular. A restauração foi realizada com resina composta Filtek Z350, devolvendo estética e função ao elemento dentário. Pode-se concluir que a técnica de transfixação horizontal de pino de fibra de vidro associado à resina composta é uma alternativa restauradora que possibilita maior resistência aos dentes tratados endodonticamente, apresenta resultados funcionais e estéticos satisfatórios, além de possibilitar uma maior sobrevida aos mesmos(AU)


The purpose of this case report was to describe in detail the technique of horizontal transfixion of a fiberglass post into an endodontically treated tooth. Female patient, 51 years old, sought the University Center of Serra Gaúcha (FSG - Caxias do Sul ­ Rio Grande do Sul) with the need to perform the endodontic treatment of molar element number 26. After the initial evaluation, endodontics was performed. The element had little support for the buccal and palatal walls, so an intraradicular postplacement followed by a crown was proposed, for financial reasons the patient did not accept it. Therefore, the technique of horizontal transfixion of a fiberglass pin was proposed, associated with a restoration of direct composite resin. The procedure was performed in a single session and a number 1 fiberglass post was fixed crosswise between the mesiopalatal and distobuccal walls. The restoration was carried out with composite resin Filtek Z350, restoring aesthetics and function. It can be concluded that the horizontal transfixion of a fiberglass post associated with composite resin technique is a restorative alternative that allows greater resistance to endodontically treated teeth, provides satisfactory esthetics and better survival rates(AU)


Assuntos
Humanos , Feminino , Pessoa de Meia-Idade , Resinas Compostas , Dente não Vital , Pinos Dentários , Dente Molar , Materiais Restauradores do Canal Radicular , Tratamento do Canal Radicular , Restauração Dentária Permanente , Resistência à Flexão
17.
Rev. cuba. estomatol ; 59(1)mar. 2022.
Artigo em Espanhol | LILACS, CUMED, BNUY-Odon, BNUY | ID: biblio-1408375

RESUMO

Introducción: Las diferencias en las propiedades mecánicas de los materiales cerámicos y a base de resina plantean la interrogante sobre cuál puede tener un mejor desempeño a largo plazo. Objetivos: Evaluar la resistencia flexural y estabilidad de color de diferentes materiales restauradores estéticos indirectos. Métodos: Los materiales seleccionados fueron Filtek™ Z250 XT (3M ESPE), Ceramage (SHOFU Dental), VITA VM® LC y VITA ENAMIC® (VITA Zahnfabrik), IPS e.max® (Ivoclar-Vivadent) y Zolid FX (Amann Girrbach AG). El ensayo de resistencia flexural (n = 10) fue realizado en una máquina universal de ensayos mecánicos. Las lecturas de color (n = 5) se midieron en un espectrofotómetro VITA Easyshade V®. Resultados: Los materiales totalmente cerámicos mostraron un mejor desempeño mecánico (p < 0,001). Los resultados de estabilidad de color muestran que Ceramage, IPS e.max® y Zolid FX, mostraron una diferencia estadísticamente significativa (p ≤ 0,002) con Filtek Z250 XT, VITA VM® LC y VITA ENAMIC®. Conclusiones: Los materiales totalmente cerámicos presentaron una mayor resistencia flexural y estabilidad de color que los materiales de base polimérica. A pesar de ello, los materiales estéticos indirectos con polímeros en su composición, como Ceramage, se presentan como una alternativa válida, ya que además de tener propiedades mecánicas adecuadas, poseen una estabilidad de color semejante a los materiales cerámicos(AU)


Introduction: Differences in the mechanical properties of ceramic and resin-based materials pose the question of which of the two will perform better in the long run. Objectives: Evaluate the flexural resistance and color stability of different indirect esthetic restorative materials. Methods: The materials selected were Filtek™ Z250 XT (3M ESPE), Ceramage (SHOFU Dental), VITA VM® LC and VITA ENAMIC® (VITA Zahnfabrik), IPS e.max® (Ivoclar-Vivadent) and Zolid FX (Amann Girrbach AG). The flexural resistance assay (n = 10) was conducted in a universal mechanical testing machine. Color readings (n = 5) were taken with a VITA Easyshade V® spectrophotometer. Results: All-ceramic materials had better mechanical performance (p < 0.001). Color stability results show that Ceramage, IPS e.max® and Zolid FX displayed a statistically significant difference (p ≤ 0.002) with respect to Filtek Z250 XT, VITA VM® LC and VITA ENAMIC®. Conclusions: All-ceramic materials exhibited greater flexural resistance and color stability than polymer-based materials. However, indirect esthetic materials with polymers in their composition, such as Ceramage, are presented as a valid alternative, due to their appropriate mechanical properties and their color stability, which is similar to that of ceramic materials(AU)


Assuntos
Humanos , Espectrofotômetros , Cor , Materiais Dentários/efeitos adversos , Resinas Compostas/uso terapêutico , Resistência à Flexão , Testes Mecânicos
18.
Braz. oral res. (Online) ; 36(Jun): e082, 2022.
Artigo em Inglês | LILACS, BNUY-Odon, BNUY | ID: biblio-1372593

RESUMO

Abstract The objective of the present study was to evaluate the effect of irradiance and radiant exposure on the chemical-mechanical properties of a resin composite. A micro-hybrid resin composite (Clearfil AP-X, Kuraray) was investigated under two different irradiances: low (300 mW/cm2) and high (800 mW/cm2) and radiant exposures: 8 and 16 J/cm2. Four groups, named Low 8 J/cm2, High 8 J/cm2, Low 16 J/cm2, and High 16 J/cm2 were tested, and their flexural strengths, elastic moduli, depths of cure, and degrees of conversion were evaluated. Data were analyzed using two-way ANOVA and Tukey's test. A multiple linear regression model was used to correlate the irradiance and radiant exposure with dependent variables (α = 0.05). Irradiance and radiant exposure were found statistically significant for all dependent variables. The interaction between the factors was statistically significant only for the degree of conversion and elastic modulus. Group Low 16 J/cm2 exhibited a significantly superior performance in all the evaluated properties. Barring the degree of conversion, no significant differences were observed among the properties evaluated between the Low 8 J/cm2 and High 8 J/cm2 groups. The adjusted R2 values were high for the depth of cure and degree of conversion (0.58 and 0.96, respectively). Both irradiance and radiant exposure parameters play an important role in establishing the final properties of a micro-hybrid resin composite. Irradiance has a greater influence under higher radiant exposures.


Assuntos
Teste de Materiais , Resinas Compostas , Materiais Dentários , Luzes de Cura Dentária , Polimerização , Resistência à Flexão , Propriedades de Superfície
19.
Rev. odontol. UNESP (Online) ; 51: e20210024, 2022. tab, ilus
Artigo em Inglês | LILACS, BBO - Odontologia | ID: biblio-1377169

RESUMO

Introduction: Screw-retained restorations have a screw access hole (SAH) sealed with resin composite aiming at safe-guarding the aesthetic features of the ceramic veneer. The loss or wear of the resin composite applied in sealing the SAH is among the most common complications in implant prosthodontics, as the fracture of ceramic veneer. Objective: Evaluate the influence of sealant materials on the fracture resistance of resin composite applied in sealing screw access hole in screwed (SAH) implants. Material and method: The samples were produced from UCLA abutments in metallic NiCr alloy with subsequent application of ceramic. After asperisation and conditioning ceramic surface, was applied silane and dentin adhesive, before sealing the conduits with resin composites Z100 and P60. Nine groups (n=10) were evaluated: sealing with Z-100 (ZNC) and P-60 (PNC) without obturation of SAH; sealing with Z100 (ZCP) and P-60 (PCP) with absorbent cotton; Z100 (ZPT) and P60 (PPT) with polytetrafluoroethylene; Z100 (ZGP) and P60 (PGP) with gutta-percha and a cemented ceramic crown (ICS). After the fracture resistance test, the data were analyzed using two-way ANOVA and Tukey HSD tests (p<.05). Result: The fracture mode was evaluated by scanning electron microscope. Irrespective of the filling material, the highest mean values of fracture resistance were observed in the sealing with P60 (p=.002). When combined with resins composed of a sealing material, the results obtained were: ZGP: 805.5N/ PGP: 929.5N

Introdução: As próteses parafusadas possuem orifício de acesso ao parafuso (SAH), os quais são selados com resina composta. Sua perda ou desgaste está entre as complicações mais comuns em próteses sobre implantes, associadas a fratura da lâmina cerâmica. Objetivo: Assim, é importante avaliar a influência dos materiais de selamento na resistência à fratura de resina composta aplicada ao SAH no selamento de prótese sobre implantes parafusadas. Material e método: As amostras foram produzidas utilizando pilares UCLA em liga metálica de NiCr com posterior aplicação de cerâmica. Após asperização e condicionamento da superfície cerâmica, foram aplicados silano e adesivo dentinário, antes da selagem dos condutos com as resinas compostas Z100 e P60. Foram avaliados nove grupos (n = 10): selamento com Z-100 (ZNC) e P-60 (PNC) sem selamento do SAH; selamento com Z100 (ZCP) e P-60 (PCP) com algodão absorvente; Z100 (ZPT) e P60 (PPT) com politetrafluoroetileno; Z100 (ZGP) e P60 (PGP) com guta-percha e coroa de cerâmica cimentada (ICS). Após o teste de resistência à fratura, os dados foram analisados usando ANOVA de dois fatores e testes Tukey HSD (p<0,05). O tipo de fratura foi avaliado por microscópio eletrônico de varredura. Resultado Independentemente do material obturador, os maiores valores médios de resistência à fratura foram observados no selamento com P60 (p=0,002). Quando combinados com resinas compostas por um material de selamento, os resultados obtidos foram: ZGP: 805,5N/ PGP: 929,5N

Assuntos
Microscopia Eletrônica de Varredura , Análise de Variância , Resinas Compostas , Prótese Dentária Fixada por Implante , Implantação Dentária , Resistência à Flexão , Reabilitação Bucal
20.
São José dos Campos; s.n; 2022. 104 p. tab, ilus, graf.
Tese em Português | LILACS, BBO - Odontologia | ID: biblio-1396533

RESUMO

O objetivo deste estudo foi avaliar in vitro a influência de um novo dispositivo fotopolimerização e pino de fibra de vidro nas propriedades mecânicas, físicoquímicas e adesão dos cimentos resinosos. Foram utilizados oitenta dentes bovinos, submetidos ao tratamento endodôntico, distribuídos em 5 grupos (n=16): CD (Pino fibra vidro e cimento dual); PF (Pino perfurado e cimento fotoativado); PD (Pino perfurado e cimento dual); POF (Pino perfurado iluminador de fibra óptica e cimento fotoativado); POD (Pino perfurado iluminador de fibra óptica e cimento dual). Os dentes foram preparados para colocação de um protótipo de pino em fibra de vidro que possui um canal interno de diâmetro regular e com conicidade progressiva. A perfuração permite a inserção da fibra óptica ao longo da extensão do pino a fim de possibilitar a ação da luz ao longo de todo o comprimento do conduto radicular. Após a cimentação, os espécimes foram seccionados perpendicularmente, e obtida 1 fatia de 2 mm de espessura do terço apical, médio e cervical. A avaliação mecânica foi realizada através do ensaio de push-out para determinação da resistência adesiva nos terços cervical, médio e apical seguido pela análise da fratura em estereomicroscópio. Os retentores intrarradiculares foram também submetidos ao teste de flexão de 3 pontos para análise do material preenchedor do pino de fibra (n=10). As análises físico - químicas foram realizadas através da determinação do grau de conversão dos cimentos (RAMAN) e análise em espectroscopia de energia dispersiva (EDS) dos monômeros presentes. A adesão foi analisada pela interface de cimentação pelo MEV e reconstrução 3D do novo sistema através do Micro-CT. Os dados obtidos foram analisados estatisticamente pelo ANOVA (um e dois fatores) e comparação múltipla de Tukey, (p<0,05). Os resultados de resistência adesiva evidenciaram que o terço apical obteve o maior valor de resistência adesiva em comparação ao terço médio (p<0,001), o grupo POD do terço apical foi estatisticamente significante em relação ao grupo CD do terço médio (p<0,001). Na analise individual de cada terço, não houve diferença entre os grupos experimentais e o controle (p>0,05). A falha adesiva entre cimento e dentina foi a mais predominante entre todos os grupos e terços. O pino de fibra de vidro (controle) obteve o maior valor de resistência à flexão (p<0,001), seguido do pino de fibra de vidro perfurado preenchido com cimento resinoso (p<0,001). Os maiores valores de GC foram alcançados pelo grupo POD com 82,3% (cervical) 69,9 % (médio) e 76,21% (apical) e o EDS comprovou a presença de componentes químicos adequados. A análise da adesão do novo pino de fibra de vidro comprova uma excelente adaptação no interior do canal radicular nas regiões cervical, médio e apical. Portanto o novo dispositivo com fibra óptica e pino de fibra de vidro experimental aumentaram as propriedades mecânicas, físico-químicas e adesão do cimento resinoso (AU)


The aim of this study was to evaluate in vitro the influence of a new light curing device with optical fiber and experimental glass fiber post on the physicochemical, mechanical, and adhesion properties of resin cements. Eighty bovine teeth were used, submitted to an endodontic treatment, distributed in 5 groups (n=16): CD (Glass fiber post and dual cement); PF (Perforated post and light-cured cement); PD (Perforated post and dual cement); POF (Fiber optic illuminating with a perforated post and lightcured cement); POD (Fiber optic illuminating with a perforated post and dual cement). The teeth were prepared for placement of a glass fiber post prototype, which has an internal canal of regular diameter and progressive taper. The internal perforation extension allows the insertion of the optical fiber along the entire length of the post in order to allow the action of light along the entire length of the root canal.The specimens were sectioned perpendicularly for the tests, and 1 slice approximately 2 mm thick was obtained from the apical, middle and cervical thirds. The mechanical evaluation was carried out through the push-out test to determine the adhesive bond strength, in the cervical, middle and apical thirds, followed by the fracture analysis under a stereomicroscope, the intraradicular post were also submitted to the 3-point bending test for material analys of the fiber post filler (n=10). The physicochemical analyzes were performed by determining the degree of conversion of the cements (RAMAN) of each sample and the analysis of energy dispersive spectroscopy (EDS) of the monomers present. Adhesion was analyzed by the cementation interface and 3D reconstruction of the new system through micro-CT, and finally, SEM analysis of the adhesive interface. The data obtained were analyzed for normality and statistically by ANOVA (one and two ways) and Tukey's multiple comparison (p<0.05). The adhesive bond strength results showed that the apical third had the highest value of adhesive strength compared to the middle third (p<0.001), and the POD group of the apical third was statistically significant in relation to the CD group of the middle third (p<0.001). In the individual analysis of each third, there was no difference between the experimental and control groups (p>0.05). Adhesive failure between cement and dentin was the most prevalent among all groups and thirds. The conventional post (control) had the highest flexural strength value (p<0.001), followed by the perforated fiberglass post filled with resin cement (p<0.001). The POD group achieved the highest GC values with 82.3% (cervical), 69.9% (medium), and 76.21% (apical) and EDS confirmed the presence of adequate chemical components. The analysis of the adhesion of the new fiberglass post proves an excellent adaptation inside the root canal in the cervical, middle and apical regions. Therefore, the new light curing device with optical fiber and experimental glass fiber post improved the resin cement's mechanical, phycochemical, and adhesion. (AU)


Assuntos
Animais , Bovinos , Análise de Variância , Técnica para Retentor Intrarradicular , Cimentos de Resina , Luzes de Cura Dentária , Resistência à Flexão , Testes Mecânicos
SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA
...