The effect of linseed oil/canola oil blend on the coating and thermal properties of waste PET-based alkyd resins.

This study aims to prepare oil-modified alkyd resins using a linseed oil/canola oil (LO/CO) blend and waste PET depolymerization product, suitable for environmentally friendly coating applications. Waste PET flakes obtained from grinding post-consumer water bottles were depolymerized by the aminoglycolysis reaction at high pressure. Raw depolymerization product (DP) was used in the synthesis of four components, 50% oil alkyd resins by monoglyceride method. DP has partly replaced the dibasic acid component in the PET-based alkyd formulations. Besides PET-based alkyds, reference alkyds without DP were also synthesized for comparison. Then, the surface coating properties and thermal behaviors of alkyd films were determined. The effect of DP usage and the changing ratios of LO/CO blend on coating properties and thermal behaviors of alkyd films were investigated. In addition, the optimum LO/CO blend ratio which is compatible with alkyd formulation was attempted to be determined. At the end of this study, glossy, soft/medium-hard films were obtained with excellent adhesion, impact strength, and chemical resistance. Thermal resistance and final thermal oxidative degradation temperature increased with adding DP to the alkyd formulation. Using LO/CO blend in the formulations affected oxidation rate and ratio, hence, drying time/degree and oxidative stability of alkyd films.

Antioxidant Activity of Humulus lupulus Phenolic Hop Extracts in Creating a New Pâté: An Element Affecting Fat Stability and Microbiological Quality during Storage.

The aim of this study was to evaluate the effect of hop extracts on changes in the primary and secondary fat oxidation products, physicochemical properties, and microbiological quality of pâté-type offal sausages obtained through the partial replacement of animal fat with vegetable fat. This study demonstrated that the extraction efficiency varied among hop cone varieties, with the highest efficiency observed for the Lubelski variety and the lowest for the Magnum variety. The phenolic compound content was higher in the Magnum cones (2.74 ± 0.11 mg/g dry matter) compared to the Lubelska cones (2.27 ± 0.05 mg/g of product). Additionally, the DPPH radical scavenging activity was greater in the extract from the Magnum cones (4.21 ± 0.09 mg TE/g d.w.) than in the extract from the Lublelski cones (3.87 ± 0.05 mg TE/ g d.w.). Similarly, the extracts from the Lubelski cones exhibited a higher antiradical activity against the ABTS radical compared to the extract from Magnum cones. Throughout storage, a significant increase in the pH value was observed in the control sample and in the samples with a 20% replacement of animal fat with rapeseed oil and Magnum hop extract. However, the addition of Lubelski hop extract resulted in a decrease in the pH value during the 15-day storage period. The samples with a 20% replacement of animal fat with rapeseed oil and 0.1% Lubelski hop extract showed the least changes in water activity during storage. The samples with a 20% replacement of animal fat with rapeseed oil and the addition of 0.2% Lubelski hop extract had the lowest peroxide value and TBARS index throughout the storage period. The addition of hop extract inhibited the growth of the total number of microorganisms in the tested sausages. In the samples with a 20% replacement of animal fat with rapeseed oil, the content of aerobic microorganisms, compared to the control sample, was statistically significantly lower.

Biodiesel Production by Methanolysis of Rapeseed Oil-Influence of SiO2/Al2O3 Ratio in BEA Zeolite Structure on Physicochemical and Catalytic Properties of Zeolite Systems with Alkaline Earth Oxides (MgO, CaO, SrO).

Alkaline earth metal oxide (MgO, CaO, SrO) catalysts supported on BEA zeolite were prepared by a wet impregnation method and tested in the transesterification reaction of rapeseed oil with methanol towards the formation of biodiesel (FAMEs-fatty acid methyl esters). To assess the influence of the SiO2/Al2O3 ratio on the catalytic activity in the tested reaction, a BEA zeolite carrier material with different Si/Al ratios was used. The prepared catalysts were tested in the transesterification reaction at temperatures of 180 °C and 220 °C using a molar ratio of methanol/oil reagents of 9:1. The transesterification process was carried out for 2 h with the catalyst mass of 0.5 g. The oil conversion value and efficiency towards FAME formation were determined using the HPLC technique. The physicochemical properties of the catalysts were determined using the following research techniques: CO2-TPD, XRD, BET, FTIR, and SEM-EDS. The results of the catalytic activity showed that higher activity in the tested process was confirmed for the catalysts supported on the BEA zeolite characterized by the highest silica/alumina ratio for the reaction carried out at a temperature of 220 °C. The most active zeolite catalyst was the 10% CaO/BEA system (Si/Al = 300), which showed the highest triglyceride (TG) conversion of 90.5% and the second highest FAME yield of 94.6% in the transesterification reaction carried out at 220 °C. The high activity of this system is associated with its alkalinity, high value of the specific surface area, the size of the active phase crystallites, and its characteristic sorption properties in relation to methanol.

Sterol Migration during Rotational Frying of Food Products in Modified Rapeseed and Soybean Oils.

This study explores the impact of rotational frying of three different food products on degradation of sterols, as well as their migration between frying oils and food. The research addresses a gap in the existing literature, which primarily focuses on changes in fat during the frying of single food items, providing limited information on the interaction of sterols from the frying medium with those from the food product. The frying was conducted at 185 ± 5 °C for up to 10 days where French fries, battered chicken, and fish sticks were fried in succession. The sterol content was determined by Gas Chromatography. This research is the first to highlight the influence of the type of oil on sterol degradation in both oils and food. Notably, sterols were found to be most stable when food products were fried in high-oleic low-linolenic rapeseed oil (HOLLRO). High-oleic soybean oil (HOSO) exhibited higher sterol degradation than high-oleic rapeseed oil (HORO). It was proven that cholesterol from fried chicken and fish sticks did not transfer to the fried oils or French fries. Despite initially having the highest sterol content in fish, the lowest sterol amount was recorded in fried fish, suggesting rapid degradation, possibly due to prefrying in oil with a high sterol content, regardless of the medium used.

Effects of different oil additives on water resistance of corn starch straws.

To investigate the effect of oil additives on improving the water resistance of corn starch straws, corn oil (CO), soybean oil (SO), rapeseed oil (RO), peanut oil (PO), lard (LD) and coconut oil (CCO) were chosen and compared the structure and properties of starch straws with different oil additives. Corn starch straws (CS), and starch straws supplemented with CO, SO, RO, PO, LD and CCO were prepared by thermoplastic extrusion. The results showed that the incorporation of oils effectively enhanced the water resistance of starch straws such as water absorption, water solubility and water swelling performance. Meanwhile, the flexural strength of starch straws significantly increased. There was no significant linear relationship among starch chain length, oil unsaturation and straw performance. Among seven starch straws, S-SO had the strongest hydrogen bond interaction (3289 cm-1) and relaxation time (0.96 ms). The S-CO had the highest relative crystallinity (16.82 %) and degree of double helix (1.535), hence resulting in the lowest water absorption and solubility values, the highest flexural strength (23.43 MPa), the highest ΔT value (9.93 °C) and ΔH value (4.79 J/g). S-RO had the highest thermal transition temperatures.

Thermomechanical transitions of meat-analog based fried foods batter coating.

This study aimed to characterize the thermomechanical transitions of meat-analog (MA) based coated fried foods. Wheat and rice flour-based batters were used to coat the MA and fried at 180 °C in canola oil for 2, 4 and 6 min. Glass-transition-temperature (Tg) of the coatings were assessed by differential scanning calorimetry, directly after frying or after post-fry holding. Mechanical texture analyzer and X-ray microtomography were employed to assess textural attributes and internal microstructure, respectively. Batter-formulation substantially impacted the Tg of fried foods coating i.e., crust. Tg of fried foods crust were ranged between -20 °C to -24 °C. Tg was positively correlated with frying time and internal microporosity (%), whereas negatively correlated with moisture content. Internal microstructure greatly influenced the textural attributes (hardness, brittleness, crispiness). Post-fry textural stability considerably impacted by Tg. Negative Tg value explains post-fry textural changes (hard-to-soft, brittle-to-ductile, crispy-to-soggy) of MA-based coated products at room-temperature (25 °C) and under IR-heating (65 °C).

Inhibitory effects and mechanisms of phenolic compounds in rapeseed oil on advanced glycation end product formation in chemical and cellular models in vitro.

Sinapic acid (SA), canolol (CAO) and canolol dimer (CAO dimer) are the main phenolic compounds in rapeseed oil. However, their possible efficacy against glycation remains unclear. This study aims to explore the impacts of these substances on the formation of advanced glycation end products (AGEs) based on chemical and cellular models in vitro. Based on fluorescence spectroscopy results, three chemical models of BSA-fructose, BSA-methylglyoxal (MGO), and arginine (Arg)-MGO showed that SA/CAO/CAO dimer could effectively reduce AGE formation but with different abilities. After SA/CAO/CAO dimer incubation, effective protection against BSA protein glycation was observed and three different MGO adducts were formed. In MGO-induced HUVEC cell models, only CAO and CAO dimer significantly inhibited oxidative stress and cell apoptosis, accompanied by the regulation of the Nrf2-HO-1 pathway. During the inhibition, 20 and 12 lipid mediators were reversed in the CAO and CAO dimer groups compared to the MGO group.

Intelligence detection of oil absorption in French fries by surface profiles.

Surface profiles are important evaluation indices for oil absorption behavior of fried foods. This research established two intelligent models of partial least-squares regression (PLSR) and back propagation artificial neural network (BP-ANN) for monitoring the oil absorption behavior of French fries based on the surface characteristics. Surface morphology and texture of French fries by rapeseed oil (RO) and high-oleic peanut oil (HOPO) at different temperatures were investigated. Results showed that oil content of samples increased with frying temperature, accounting for 37.7% and 41.4% of samples fried by RO and HOPO respectively. The increase of crust ratio, roughness and texture parameters (Fm, Nwr, fwr, Wc) and the decrease of uniformity were observed with the frying temperature. Coefficients of prediction set of PLSR and BP-ANN models were more than 0.93, which indicated that surface features combined with chemometrics were rapid and precise methods for determining the oil content of French fries.

Does protein deamidation enhance rice protein concentrate's ability to produce and stabilize high internal phase emulsions?

Rice is one of the most consumed grains in the world. Rice protein has great nutritional value as a hypoallergenic protein and due to its high lysine content, a limiting amino acid in several other plant protein sources. However, rice protein has low solubility, hampering its use in many applications in the food industry. In this context, alkaline deamidation (0.5 h, 343 K, and pH 11) was applied to modify the protein structure of rice protein concentrate (RPC). After deamidation, two protein powders were produced: (i) one containing the whole protein fraction recovered after RPC deamidation (DT) and (ii) another containing only the soluble fraction recovered after RPC deamidation (DS). Protein dispersions were characterized by SDS-PAGE, zeta potential, solubility, surface hydrophobicity, and capacity to hold water and oil. RPC could not structure canola oil into a high internal phase emulsion (HIPE) due to its low solubility. DT and DS dispersions displayed solubility much higher than RPC and enabled the structuration of HIPEs with 75 % (w/w) canola oil and 25 % of DT or DS dispersions (2, 4, and 6 % w/w). HIPEs were characterized regarding particle size, microstructure, Turbiscan and oil loss stabilities, and rheological behavior for 60 days. Turbiscan analysis and oil loss measurements showed high stability, and the thixotropy tests showed high recovery in all HIPEs. Higher protein concentrations and DS dispersions produced HIPEs with smaller particle sizes. However, rheological measurements indicate that HIPEs produced with DT dispersions had better results, maintaining their structure over the 60 days. Furthermore, DT is cheaper to produce; therefore, DT 4 and 6 % w/w were the most promising for producing HIPEs. The HIPEs produced in this study displayed great potential as fat replacers.

Gas chromatography ion mobility spectroscopy: A rapid and effective tool for monitoring oil oxidation.

Oil autoxidation is an early process of food deterioration, monitoring oil oxidation is therefore of great significance to ensure food quality and safety. In this study, a detection method of the primary and secondary oxidative products was developed by gas chromatography ion mobility spectrometry (GC-IMS).The secondary oxidative products was analyzed by GC-IMS. Then, the relationships between peroxide values and the contents of secondary oxidative products were investigated by constructing a prediction model of peroxide value of rapeseed oil with the help of secondary oxidative products and chemometrics. The coefficient of determination Q2 of the model validation set is 0.96, and the RMSECV is 0.1570 g/100 g. These validation results indicated that secondary oxidative products could also reflect the content of the primary oxidative products. Moreover, 10 characteristic markers related to oxidative rancidity were identified for monitoring edible oil rancidity and oxidative stability.

Effects of Silica Hydrogel on Degumming of Fragrant Rapeseed Oil.

Hot-pressed rapeseed oils with pleasant flavor, i.e., fragrant rapeseed oils, are favored by consumers, especially people from the southwest provinces of China. Although degumming is an important section in producing edible rapeseed oils, conventional degumming techniques are generally suffered from disadvantages such as moisture control, and large losses of micronutrients and flavors. In the present paper, hot-pressed rapeseed oils were treated with silica hydrogel to remove their gums, and changes in phospholipids, acid values, peroxide values, tocopherols, total phenols, and flavor compounds were analyzed to compare the silica hydrogel-degumming with conventional methods. The optimized conditions were suggested to be carried out at 45°C for 15 min, and the silica hydrogel dosage was 1.10%. More than 97.00% of phospholipids were removed after the degumming, and more than 85.00% of micronutrients, were retained in the treated oils. The degumming efficiency was therefore significantly higher than those operated by conventional acid degumming and soft degumming techniques. It was found that the dosage of the silica hydrogel significantly affected the removal rate of phospholipids compared with degumming time and temperature. There were nearly typical volatile compounds found in the rapeseed oils, while most of them kept almost stable after the silica hydrogel-degumming. In this regard, silica hydrogel adsorption exhibited little effect on volatile compounds, making it more suitable for the production of fragrant rapeseed oils.

Evaluation of different regression models for detection of adulteration of mustard and canola oil with argemone oil using fluorescence spectroscopy coupled with chemometrics.

Mustard and canola oils are commonly used cooking oils in Asian countries such as India, Nepal, and Bangladesh, making them prone to adulteration. Argemone is a well-known adulterant of mustard oil, and its alkaloid sanguinarine has been linked with health conditions such as glaucoma and dropsy. Utilising a non-destructive spectroscopic method coupled with a chemometric approach can serve better for the detection of adulterants. This work aimed to evaluate the performance of various regression algorithms for the detection of argemone in mustard and canola oils. The spectral dataset was acquired from fluorescence spectrometer analysis of pure as well as adulterated mustard and canola oils with some local and commercial samples also. The prediction performance of the eight regression algorithms for the detection of adulterants was evaluated. Extreme gradient boosting regressor (XGBR), Category gradient boosting regressor (CBR), and Random Forest (RF) demonstrate potential for predicting adulteration levels in both oils with high R2 values.

Effect of enzymatic Maillard reaction conditions on physicochemical properties, nutrition, fatty acids composition and key aroma compounds of fragrant rapeseed oil.

BACKGROUND: A new enzymatic hydrolysis-based process inspired by the Maillard reaction can produce strong flavored, high-value rapeseed oil that meets safety requirements. In the present study, the effect of reaction time (10-30 min) and temperature (130-160 °C) on the physicochemical properties, nutritional status, fatty acids composition and key aroma compounds of fragrant rapeseed oil (FRO) was investigated. RESULTS: An increasing reaction time and temperature substantially decreased the total tocopherol, polyphenol and sterol contents of FRO, but increased benzo[a]pyrene content, as well as the acid and peroxide values, which did not exceed the European Union legislation limit. Among the volatile components, 2,5-dimethyl was the main substance contributing to the barbecue flavor of FRO. The 150 °C for 30 min reaction conditions produced a FRO with a strong, fragrant flavor, with high total tocopherol (560.15 mg kg-1 ), polyphenol (6.82 mg kg-1 ) and sterol (790.65 mg kg-1 ) contents; acceptable acid (1.60 mg g-1 ) and peroxide values (4.78 mg g-1 ); and low benzo[a]pyrene (1.39 mg g-1 ) content. These were the optimal conditions for the enzymatic Maillard reaction, according to the principal component analysis. Furthermore, hierarchical cluster analysis showed that reaction temperature had a stronger effect on FRO than reaction time. CONCLUSION: The optimal enzymatic Maillard reaction conditions for the production of FRO are heating at 150 °C for 30 min. These findings provide new foundations for better understanding the composition and flavor profile of FRO, toward guiding its industrial production. © 2023 Society of Chemical Industry.

Added γ-oryzanol boosted anti-inflammatory effects of canola oil in adult subjects with type 2 diabetes: a randomized controlled clinical trial.

PURPOSE: This study was conducted to examine the effects of daily intake of γ-oryzanol (ORZ)-fortified canola oil, as compared with plain canola and sunflower oils, on certain inflammatory and oxidative stress biomarkers in adult subjects with Type 2 Diabetes (T2D). METHODS: We randomly allocated 92 adult subjects with T2D from both sexes to one of the following groups to receive: (a) ORZ-fortified canola oil (ORZO; n1 = 30); (b) unfortified canola oil (CANO; n2 = 32); or (c) sunflower oil (SUFO; n3 = 30) for 12 weeks. Dietary and laboratory evaluations were performed initially and finally. RESULTS: Serum hs-CRP concentrations significantly decreased in ORZO group (from 3.1 ± 0.2 to 1.2 ± 0.2 mg/L), as compared with CANO (p = 0.003) and SUFO (p < 0.001) groups. Serum IL-6 significantly decreased just in ORZO (- 22.8%, p = 0.042) and CANO groups (- 19.8%, p = 0.038). However, the between-group differences were not significant. Serum IL-1ß slightly decreased in ORZO (- 28.1%, p = 0.11) and increased in SUFO (+ 20.6%, p = 0.079) but between-group difference was statistically significant (p = 0.017). Serum IFN-γ concentrations decreased significantly only in ORZO (from 3.3 ± 0.08 to 2.9 ± 0.21 IU/mL, p = 0.044). Salivary IgA concentrations increased significantly in all three intervention groups. Notwithstanding, only the difference between ORZO and CANO groups was statistically significant (p = 0.042). Similarly, circulating malondialdehyde concentrations significantly decreased in all three groups but with no between-group significant difference. CONCLUSIONS: Daily consumption of ORZ-fortified canola oil, compared with unfortified canola and sunflower oils, for 12 weeks resulted in boosting of certain anti-inflammatory effects of canola oil. These findings may have preventive implications for both clinicians and policy makers. This clinical trial was registered at clinicaltrials.gov (03.08.2022; NCT05271045).

Do meals contain a relevant amount of oxylipins? LC-MS-based analysis of oxidized fatty acids in food.

Several oxylipins are potent lipid mediators and are discussed to be absorbed after oral intake. However, information about their concentrations in oils and processed foods are scarce. Here, we analyzed the concentrations of mono-, di- and multihydroxy- as well as epoxy-PUFA in virgin and refined oils as well as in different foods/meals. Oil refining causes hydrolysis of epoxy-PUFA and thus high dihydroxy-PUFA concentrations (e.g. 15,16-DiHODE 290 µg/g in refined vs. 15 µg/g in virgin rapeseed oil), making the epoxy-to-diol ratio a potential marker for refined oils. Low oxylipin levels were found in foods with high amounts of saturated fatty acids such as Hamburger patties (around 30 µg/g). High concentrations (up to 1200 µg/g, 80 mg per serving) and high oxylipin/precursor-PUFA ratios were found in fried falafel and processed foods such as vegetarian sausage/fish fingers. Our study provides first insights in the oxylipin concentrations of our daily food, indicating a relevant intake.

Effects of rapeseed oil on body composition and glucolipid metabolism in people with obesity and overweight: a systematic review and meta-analysis.

To investigate the effects of rapeseed oil on body composition, blood glucose and lipid metabolism in people with overweight and obesity compared to other cooking oils. We searched eight databases for randomized controlled studies (including randomized crossover trials). The risk of bias for the included studies was assessed using the Cochrane Risk of Bias 2.0 tool. The Grading of Recommendations Assessment Development and Evaluation (GRADE) criteria were used to evaluate the quality of the outcomes. The methodological quality of the included studies was assessed using the Physiotherapy Evidence Database (PEDro) scale. Sensitivity analysis was used to check the stability of the pooled results. Statistical analysis was carried out using Review Manager 5.3 software. As a result, fifteen randomized controlled studies (including six parallel studies and nine crossover studies) were included in this study. Compared to other edible oils, rapeseed oil significantly reduced low density lipoprotein cholesterol (LDL-C) (MD = -0.14 mmol/L, 95% CI: -0.21, -0.08, I2 = 0%, P < 0.0001), apolipoprotein B (ApoB) (MD = -0.03 g/L, 95% CI: -0.05, -0.01, I2 = 0%, P = 0.0003), ApoB/ApoA1 (MD = -0.02, 95% CI: -0.04, -0.00, I2 = 0%, P = 0.02) and insulin (MD = -12.45 pmol/L, 95% CI: -19.61, -5.29, I2 = 37%, P = 0.0007) levels, and increased fasting glucose (MD = 0.16 mmol/L, 95% CI: 0.05, 0.27, I2 = 27%, P = 0.003) levels. However, the differences in body weight and body composition between rapeseed oil and control oils were not significant. In a word, rapeseed oil is effective in reducing LDL-C, ApoB and ApoB/ApoA1 levels in people with overweight and obesity, which is helpful in preventing and reducing the risk of atherosclerosis. PROSPERO registration number: CRD42022333436.

Overall quality changes and deterioration mechanism of fragrant rapeseed oils during 6-Month storage.

The strong-fragrant rapeseed oil (SFRO) is a popular rapeseed oil in China with a low refining degree only degumming with hot water, which remarkably affects its storage stability. The present study compared the overall changes of physical/chemical/nutrient quality of FROs at various temperatures, light wavelengths and headspace volumes. Results showed that red light (680 nm) had a most significant adverse effect on the overall quality of SFRO with the higher correlation coefficients to PV and TOTOX of 0.71 and 0.70, and lower correlation coefficients to chlorophyll and tocopherol of -0.95 and -0.53, respectively. Further studies revealed that red light accelerated the oxidation of fragrant rapeseed oils by degrading chlorophyll to initiate the photo-oxidation process and synthesize high amount of secondary oxidation products including aliphatic and aromatic oxidized compounds from linolenic acid. These findings provided a reference to control the deterioration of FROs by preventing the transmittance of red light.

Revealing oxidative degradation of lipids and screening potential markers of four vegetable oils during thermal processing by pseudotargeted oxidative lipidomics.

The oxidative degradation of lipids in vegetable oils during thermal processing may present a risk to human health. However, not much is known about the evolution of lipids and their non-volatile derivatives in vegetable oils under different thermal processing conditions. In the present study, a pseudotargeted oxidative lipidomics approach was developed and the evolution of lipids and their non-volatile derivatives in palm oil, rapeseed oil, soybean oil, and flaxseed oil under different thermal processing conditions was investigated. The results showed that thermal processing resulted in the oxidative degradation of TGs in vegetable oils, which generated oxTGs, DGs, and FFAs, as well as TGs with smaller molecular weights. The lower the fatty acid saturation, the more severe the oxidative degradation of vegetable oils and thermal processing at high temperatures should be avoided if possible. From the accumulation of oxTGs concentrations, the hazards during thermal processing at high temperatures were, in descending order, soybean oil, rapeseed oil, flaxseed oil, and palm oil. The non-volatile potential markers were screened in palm oil, rapeseed oil, soybean oil, and flaxseed oil for 1, 7, 5, and 2 markers related to thermal processing time, respectively. The study provided suggestions for the consumption of vegetable oils from multiple perspectives and identified markers for monitored oxidative degradation of vegetable oils.

Interfacial adsorption of soybean phosphatidylethanolamine in different oil phase and the stability of water-in-oil emulsion.

Water-in-oil (W/O) emulsion holds great potential in designing fat-reduced foods. However, due to the lack of W/O-type surfactant, formation of all-natural W/O emulsion is challenged. This study aimed to investigate the effect of oil phase on interfacial adsorption of soybean phosphatidylethanolamine (SP) and stability of W/O emulsion. Five oils, including medium chain triglycerides oil (MO), coconut oil (CO), palm kernel oil (PKO), sunflower oil (SO) and rapeseed oil (RO), were selected. Results showed that diffusion rate of SP to the interface ranked as MO > CO > PKO > SO ≈ RO, increasing interfacial adsorption from 50.2 % to 85.3 %. Higher interfacial adsorption improved the deformation resistance of interfacial layer, causing more significant decrease in interfacial tension (3.54 mN/m). So, the largest water fraction (65 %) was stabilized by SP with MO and CO, and exhibited smaller droplet sizes and better stability. Consequently, shorter-chain oil was more suitable for preparing W/O emulsions.

Effects of dietary camelina, flaxseed, and canola oil supplementation on plasma fatty acid concentrations and health parameters in horses.

Camelina (Camelina sativa) is a hardy, low-input oilseed crop that provides a rich source of the n-3 fatty acid, α-linolenic acid (ALA). The primary purpose of the present study was to assess the effects of dietary camelina oil (CAM) consumption on various health parameters, as compared to horses fed canola oil (OLA) or flax oil (FLX). Secondly, to determine how dietary CAM, FLX, and OLA alter circulating plasma total lipids across time. Thirty horses, from three separate herds, were used for this study [14.9 years ± 5.3 years; 544 ± 66 kg calculated BW (mean ± SD)]. After a 4-week gradual acclimation period using sunflower oil mixed with soaked hay cubes, horses were balanced by location, age, sex, weight, and breed and randomly allocated to one of three treatment oils (CAM, OLA, or FLX) at an inclusion of 370 mg of oil/kg BW/day. Horses had ad libitum access to hay and/or pasture for the duration of the study. Body condition score (BCS), BW, oil intake, complete blood counts, plasma biochemical profiles, and plasma total lipids were measured on weeks 0, 2, 4, 8, and 16 throughout the 16-week treatment period. BW, BCS, and oil intake were analyzed using an ANOVA using PROC GLIMMIX in SAS Studio. Complete blood counts and biochemical profiles were analyzed using an ANCOVA, and fatty acids were analyzed using an ANOVA in PROC MIXED in SAS Studio. No differences were observed among treatment groups for BW, BCS, oil intake, complete blood counts, and biochemical parameters. Individual fatty acids that differed among treatments and/or across time were largely reflective of the different FA profiles of the oils provided. Most notably, plasma ALA was greater for FLX than OLA, but neither differed from CAM (P = 0.01). Linoleic acid did not differ among treatments or over time (P > 0.05). The n-6:n-3 ratio decreased over time for both CAM and FLX, and ratios were lower for FLX than OLA at week 16, but not different from CAM (P = 0.02). These results suggest that dietary CAM had no adverse effects on health parameters and that daily supplementation of CAM and FLX at 370 mg of oil/kg BW/day induces positive changes (a decrease) in the n-6:n-3 status of the horse. Consequently, CAM may be considered as an alternative oil to FLX in equine diets.