An efficient method of preparing Si-Fe-Al-Ca alloy from coal gasification fine slag via plasma smelting and alternating current magnetic field.

It is of great significance to solve the environmental problems caused by the unreasonable treatment of coal gasification slag. This study successfully produced Si-Fe-Al-Ca alloy from low-carbon fine slag with petroleum coke as reducing agent in a plasma furnace with an alternating current magnetic field, which solved the problem of the high reactivity requirement of carbon reductant for plasma smelting. The optimum carbon content of the mixed low-carbon fine slag and petroleum coke is 105% of the theoretical value. As the strength of the alternating current magnetic field increased (from 0% to 100% of the maximum power), the yield of the alloy (from 25.46% to 58.19%) and the recovery ratios of each element (Si, Fe, Al, Ca, Ti) increased. In addition, as the magnetic field strength increased, the pores inside the alloy became smaller, the composition of the alloy became more homogeneous, and a better separation of the alloy from the slag was observed. The main composition of the alloy at the strongest alternating current magnetic field is Si: 51.14 wt%, Fe: 28.41 wt%, Al: 9.14 wt%, Ca: 7.15 wt%, Ti: 2.03 wt%. We attribute the enhanced smelting effect of the alternating current magnetic field to the resistive heat and Lorentz force produced by the induced current. In addition, the skin effect concentrated the induced current on the surface of the oxide particles and carbon particles, which increased the temperature of the reaction interface and promoted the carbothermal reduction reaction.

[Characteristics, Sources Apportionment, and Health Risks of PM2.5-bound PAHs and Their Derivatives Before and After Heating in Zibo City].

Atmospheric polycyclic aromatic hydrocarbons (PAHs) and their derivatives are a global problem that influences the environment and threatens human health. To investigate the characteristics, sources, and health risk assessment of PM2.5-bound PAHs and their derivatives, PM2.5 were collected at an urban site in Zibo from November 5 to December 26, 2020, and the concentrations of 16 conventional PAHs, nine NPAHs, and five OPAHs in PM2.5 were analyzed using gas chromatography-mass spectrometry. Source apportionment of PAHs and their derivatives was conducted using diagnostic ratios and a PMF model, and the health risks of PAHs and their derivatives to adult men and women were evaluated using the source-dependent incremental lifetime cancer risk (ILCR) model. The results showed that the average concentrations of ∑16pPAHs, ∑9NPAHs, and ∑5OPAHs in PM2.5 of Zibo City during the sampling period were (41.61 ± 13.40), (6.38 ± 5.70), and (53.20 ± 53.47) ng·m-3, respectively. The concentrations of the three PAHs increased significantly after heating, which were 1.31, 2.04, and 5.24 times larger than those before heating. During the sampling period, Chr, BaP, and BaA were the dominant components of pPAHs; 9N-Ant and 2N-Flt + 3N-Flt were the dominant components of NPAHs; and ATQ and BZO were the dominant components of OPAHs. Source apportionment results showed that motor vehicles were the main source of PAHs and their derivatives in PM2.5 before heating, whereas after heating, the main sources were the mixed source of coal and biomass combustion and secondary formation. The total BaP equivalent (TEQ) was 14.5 ng·m-3 during the sampling period, and the TEQ increased significantly after heating, which was approximately 1.2 times of that before heating. Assisted by the individual PAH source apportionment results, the ILCR of PM2.5-boundPAHs and NPAHs in Zibo City had a certain potential carcinogenic risk for adult males (1.06 × 10-5) and females (9.32 × 10-6). Among them, the health risks of PAHs from gasoline vehicles, diesel vehicles, and coal/biomass combustion were significantly higher than those from other emission sources.

Lentzea sokolovensis sp. nov., Lentzea kristufekii sp. nov. and Lentzea miocenica sp. nov., rare actinobacteria from Miocene lacustrine sediment of the Sokolov Coal Basin, Czech Republic.

The taxonomic position of three actinobacterial strains, BCCO 10_0061T, BCCO 10_0798T, and BCCO 10_0856T, recovered from bare soil in the Sokolov Coal Basin, Czech Republic, was established using a polyphasic approach. The multilocus sequence analysis based on 100 single-copy genes positioned BCCO 10_0061T in the same cluster as Lentzea waywayandensis, strain BCCO 10_0798T in the same cluster as Lentzea flaviverrucosa, Lentzea californiensis, Lentzea violacea, and Lentzea albidocapillata, and strain BCCO 10_0856T clustered together with Lentzea kentuckyensis and Lentzea alba. Morphological and chemotaxonomic characteristics of these strains support their assignment to the genus Lentzea. In all three strains, MK-9(H4) accounted for more than 80 % of the isoprenoid quinone. The diagnostic diamino acid in the cell-wall peptidoglycan was meso-diaminopimelic acid. The whole-cell sugars were rhamnose, ribose, mannose, glucose, and galactose. The major fatty acids (>10 %) were iso-C15 : 0, anteiso-C15 : 0, iso-C16 : 0, and C16 : 0. The polar lipids were diphosphatidylglycerol, methyl-phosphatidylethanolamine, phosphatidylethanolamine, hydroxy-phosphatidylethanolamine, phosphatidylglycerol, and phosphatidylinositol. The genomic DNA G+C content of strains (mol%) was 68.8 for BCCO 10_0061T, 69.2 for BCCO 10_0798T, and 68.5 for BCCO 10_0856T. The combination of digital DNA-DNA hybridization results, average nucleotide identity values and phenotypic characteristics of BCCO 10_0061T, BCCO 10_0798T, and BCCO 10_0856T distinguishes them from their closely related strains. Bioinformatic analysis of the genome sequences of the strains revealed several biosynthetic gene clusters (BGCs) with identities >50 % to already known clusters, including BGCs for geosmin, coelichelin, ε-poly-l-lysine, and erythromycin-like BGCs. Most of the identified BGCs showed low similarity to known BGCs (<50 %) suggesting their genetic potential for the biosynthesis of novel secondary metabolites. Based on the above results, each strain represents a novel species of the genus Lentzea, for which we propose the name Lentzea sokolovensis sp. nov. for BCCO 10_0061T (=DSM 116175T), Lentzea kristufekii sp. nov. for BCCO 10_0798T (=DSM 116176T), and Lentzea miocenica sp. nov. for BCCO 10_0856T (=DSM 116177T).

Portable luminescent fiber- and glove-based nanosensor for multicolor visual detection of tetracycline in food samples.

An intelligent fluorescent nanoprobe (lignite-CDs-Eu) was constructed by an effective and facile method based on lignite-derived carbon dots (CDs) and lanthanide europium ions (Eu3+), which exhibited high sensitivity, low detection limit (13.35 nM) and visual color variation (from blue to red) under ultraviolet light towards tetracycline (TC) detection. Significantly, portable and economical sensors were developed using lignite-CDs-Eu immobilized fiber material of filter paper and wearable glove with the aid of color extracting and image processing application (APP) in the smartphone. Facile, fast and real-time visual detection of TC in food samples was realized. Moreover, logic gate circuit was also designed to achieve intelligent and semi-quantitative inspection of TC. To some extent, this study extended the cross-application of intelligent computer software in food analytical science, and provided a certain reference for the development of small portable detection sensors which were suitable for convenience and non-professional use in daily life.

Research and application of bag filter system for railway ballast bed coal suction vehicles: An optimization and application study.

The current bag filter system used by railway ballast bed coal suction vehicles for cleaning coal dust from railway tunnels has low operational efficiency and generates significant volumes of dust. This paper describes a simulation test unit designed to enhance the dust removal performance in railway tunnels. The flow field inside the simulation test unit is investigated under different operating conditions through numerical simulations, and the variations in air volume and working resistance, total dust collection efficiency, and optimal operating parameters of a pulse cleaning system are identified through a series of experiments. The numerical results show that the pulse cleaning system does not significantly affect the uniformity of the flow field distribution at the bottom of the filter cartridge during the process of operation. The experimental research indicates that the simulation test unit satisfies the design requirements, achieving an average total dust removal efficiency of 99.93%. A field application shows that the total dust mass concentration at the operator position can be reduced from 335.8 mg∙m-3 to 4.2 mg∙m-3, effectively improving the operating environment within the tunnel.

Coal-Derived Humic Substances: Insight into Chemical Structure Parameters and Biomedical Properties.

An investigation was carried out on humic substances (HSs) isolated from the coal of the Kansk-Achinsk basin (Krasnoyarsk Territory, Russia). The coal HSs demonstrate the main parameters of molecular structure inherent to this class of natural compounds. An assessment was performed for the chemical, microbiological, and pharmacological safety parameters, as well as the biological efficacy. The HS sample meets the safety requirements in microbiological purity, toxic metals content (lead, cadmium, mercury, arsenic), and radionuclides. The presence of 11 essential elements was determined. The absence of general, systemic toxicity, cytotoxicity, and allergenic properties was demonstrated. The coal HS sample was classified as a Class V hazard (low danger substances). High antioxidant and antiradical activities and immunotropic and cytoprotective properties were identified. The ability of the HS to inhibit hydroxyl radicals and superoxide anion radicals was revealed. Pronounced actoprotective and nootropic activities were also demonstrated in vivo. Intragastric administration of the HS sample resulted in the improvement of physical parameters in mice as assessed by the "swim exhaustion" test. Furthermore, intragastric administration in mice with cholinergic dysfunction led to a higher ability of animals with scopolamine-induced amnesia to form conditioned reflexes. These findings suggest that the studied HS sample is a safe and effective natural substance, making it suitable for use as a dietary bioactive supplement.

Neighborhood-scale lead (Pb) speciation in Akron, Ohio (USA) soils: primary sources, post-deposition diagenesis, and high concentrations of labile Pb.

Lead (Pb) poses a significant risk to infants and children through exposure to contaminated soil and dust. However, there is a lack of information on Pb speciation and distribution at the neighborhood-scale. This work aimed to determine: (1) the distribution of acid-extractable (labile) Pb and other metals ([M]AE) in two neighborhoods in Akron, Ohio (USA) (Summit Lake and West Akron; n = 82 samples); and (2) Pb speciation and potential sources. Total metal concentration ([M]T) and [M]AE was strongly correlated for Pb and Zn (R2 of 0.66 and 0.55, respectively), corresponding to 35% and 33% acid-extractability. Lead and Zn exhibited a strong positive correlation with each other (R2 = 0.56 for MT and 0.68 for MAE). Three types of Pb-bearing phases were observed by electron microscopy: (1) galena (PbS)-like (5-10 µm); (2) paint chip residuals (10-20 µm); and (3) Pb-bearing Fe-oxides (20 µm). Isotope ratio values for PbAE were 1.159 to 1.245 for 206Pb/207Pb, and 1.999 to 2.098 for 208Pb/206Pb, and there was a statistically significant difference between the two neighborhoods (p = 0.010 for 206Pb/207Pb and p = 0.009 for 208Pb/206Pb). Paint and petrol are the dominant sources of Pb, with some from coal and fly ash. Lead speciation and distribution is variable and reflects a complex relationship between the input of primary sources and post-deposition transformations. This work highlights the importance of community science collaborations to expand the reach of soil sampling and establish areas most at risk based on neighborhood-dependent Pb speciation and distribution for targeted remediation.

Ecological risk assessment of heavy metals in desulfurized seawater discharged from a coal-fired power plant in Qingdao.

Despite the prevalence of discharge of large volumes of heavy-metal-bearing seawater from coal-fired power plants into adjacent seas, studies on the associated ecological risks remain limited. This study continuously monitored concentrations of seven heavy metals (i.e. As, Cd, Cr, Cu, Hg, Pb, and Zn) in surface seawater near the outfall of a coal-fired power plant in Qingdao, China over three years. The results showed average concentrations of As, Cd, Cr, Cu, Hg, Pb, and Zn of 2.63, 0.33, 2.97, 4.63, 0.008, 0.85, and 25.00 µg/L, respectively. Given the lack of data on metal toxicity to local species, this study investigated species composition and biomass near discharge outfalls and constructed species sensitivity distribution (SSD) curves with biological flora characteristics. Hazardous concentrations for 5% of species (HC5) for As, Cd, Cr, Cu, Hg, Pb, and Zn derived from SSDs constructed from chronic toxicity data for native species were 3.23, 2.22, 0.06, 2.83, 0.66, 4.70, and 11.07 µg/L, respectively. This study further assessed ecological risk of heavy metals by applying the Hazard Quotient (HQ) and Joint Probability Curve (JPC) based on long-term heavy metal exposure data and chronic toxicity data for local species. The results revealed acceptable levels of ecological risk for As, Cd, Hg, and Pb, but unacceptable levels for Cr, Cu, and Zn. The order of studied heavy metals in terms of ecological risk was Cr > Cu ≈ Zn > As > Cd ≈ Pb > Hg. The results of this study can guide the assessment of ecological risk at heavy metal contaminated sites characterized by relatively low heavy metal concentrations and high discharge volumes, such as receiving waters of coal-fired power plant effluents.

Increase in Agricultural-Derived NHx and Decrease in Coal Combustion-Derived NOx Result in Atmospheric Particulate N-NH4+ Surpassing N-NO3- in the South China Sea.

The atmospheric deposition of anthropogenic active nitrogen significantly influences marine primary productivity and contributes to eutrophication. The form of nitrogen deposition has been evolving annually, alongside changes in human activities. A disparity arises between observation results and simulation conclusions due to the limited field observation and research in the ocean. To address this gap, our study undertook three field cruises in the South China Sea in 2021, the largest marginal sea of China. The objective was to investigate the latest atmospheric particulate inorganic nitrogen deposition pattern and changes in nitrogen sources, employing nitrogen-stable isotopes of nitrate (δ15N-NO3-) and ammonia (δ15N-NH4+) linked to a mixing model. The findings reveal that the N-NH4+ deposition generally surpasses N-NO3- deposition, attributed to a decline in the level of NOx emission from coal combustion and an upswing in the level of NHx emission from agricultural sources. The disparity in deposition between N-NH4+ and N-NO3- intensifies from the coast to the offshore, establishing N-NH4+ as the primary contributor to oceanic nitrogen deposition, particularly in ocean background regions. Fertilizer (33 ± 21%) and livestock (20 ± 6%) emerge as the primary sources of N-NH4+. While coal combustion continues to be a significant contributor to marine atmospheric N-NO3-, its proportion has diminished to 22 (Northern Coast)-35% (background area) due to effective NOx emission controls by the countries surrounding the South China Sea, especially the Chinese Government. As coal combustion's contribution dwindles, the significance of vessel and marine biogenic emissions grows. The daytime higher atmospheric N-NO3- concentration and lower δ15N-NO3- compared with nighttime further underscore the substantial role of marine biogenic emissions.

The biotic effects of lignite on humic acid components conversion during chicken manure composting.

Targeted regulation of composting to convert organic matter into humic acid (HA) holds significant importance in compost quality. Owing to its low carbon content, chicken manure compost often requires carbon supplements to promote the humification progress. The addition of lignite can increase HA content through biotic pathways, however, its structure was not explored. The Parallel factor analysis revealed that lignite can significantly increase the complexity of highly humified components. The lignite addition improved phenol oxidase activity, particularly laccase, during the thermophilic and cooling phases. The abundance and transformation functions of core bacteria also indicated that lignite addition can influence the activity of microbial transformation of HA components. The structural equation model further confirmed that lignite addition had a direct and indirect impact on enhancing the complexity of HA components through core bacteria and phenol oxidase. Therefore, lignite addition can improve HA structure complexity during composting through biotic pathways.

[Effects of coal mine waste dump on soil seed bank and vegetation distribution pattern]. / ç ¤çŸ¿æŽ’çŸ¸åœºå¯¹å‘¨è¾¹åœŸå£¤ç§å­åº“åŠæ¤è¢«åˆ†å¸ƒæ ¼å±€çš„å½±å“.

Long-term occupation of coal gangue dumping sites (CGDS) may destroy ecological environment of nearby area. However, how the CGDS affects the distribution pattern of soil seed banks and vegetation in the nearby area is not clear. In this study, we investigated soil seed bank and vegetation at different distances from the second CGDS of Yangchangwan in Ningdong mining area, Lingwu, Ningxia. The results showed that soil seed bank was mainly distributed in 0-10 cm layer and decreased with increasing soil depth. Species richness of soil seed bank and vegetation first increased and then tended to be stable with increasing distance to the CGDS. The influence range of CGDS on soil seed banks was 300-500 m and was 100-300 m on aboveground vegetation. The CGDS did not affect the vertical distribution pattern of soil seed bank, but significantly affected the horizontal distribution pattern of soil seed banks and aboveground vegetation. The key area of vegetation restoration around the CGDS was between 100 m and 300 m.

Potential toxic components in size-resolved particles and gas from residential combustion: Emission factor and health risk.

Particulate matter (PM) from residential combustion is an existential threat to human health. Emission factors (EFs) of multiple potential toxic components (PTCs) in size-resolved PM and gas from eight residential fuel combustion were measured, and size distribution, gas/particle partitioning and health risks of the PTCs were investigated. Average EFs from clean coal and anthracite coal were PTEs (sum of EFs of 11 Potential Toxic Elements, 6.62 mg/kg fuels) > PAHs (sum of 22 Polycyclic Aromatic Hydrocarbons, 1.12 mg/kg) > OPAHs (sum of 5 Oxygenated Polycyclic Aromatic Hydrocarbons, 0.45 mg/kg) > PAEs (sum of 6 Phthalate Esters, 0.11 mg/kg) > NPAHs (sum of 14 Nitropolycyclic Aromatic Hydrocarbons, 16.84 µg/kg) > OPEs (sum of 7 Organophosphate Esters, 7.57 µg/kg) > PCBs (sum of 6 Polychorinated Biphenyls, 0.07 µg/kg), which were 2-3 and 1-2 orders of magnitude lower than the EFs of PTCs (except PTEs) from bituminous coal and biomass. Most PAHs, OPAHs and NPAHs, which may mainly originate from chemical reactions, showed similar size distributions and averagely 85 % concentrated in PM1. PTEs, PAEs, OPEs and PCBs generated from the release from raw fuels may have a higher proportion, so their size distributions were more complex and varied with combustion temperature, volatility of compounds, binding mode of the raw fuels, and so on. In addition, clean coal and high-quality anthracite coal could reduce the health risks from the potential organic toxic components, but also reveal the stumbling block of PTEs in risk control.

Health risks of exposure to air pollution in areas where coal-fired power plants are located: protocol for a scoping review.

INTRODUCTION: Coal-fired power plants are major sources of air pollution which impact human health. Coal combustion byproducts released into the air include particulate matter, nitrogen oxides and sulphur dioxide. Exposure to fine particulate matter is associated with increased risk of mortality. This scoping review will examine and summarise the current literature on the health risks of exposure to air pollution in areas in which coal-fired power plants exist. METHODS AND ANALYSIS: This scoping review will be conducted according to the Joanna Briggs Institute methodological framework and reported in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses extension for Scoping Reviews guidelines. Five electronic databases (PubMed, ScienceDirect, Scopus, Web of Science and Google Scholar) will be searched for relevant articles. Studies will be included up until 31 January 2024. There will be no restriction on geographical area. The searches will be limited to studies published in English. Title, abstract, full-text screening and data extraction of relevant articles will be done by two independent reviewers. Discrepancies will be resolved by group discussion. The findings will be presented in tables with a narrative summary. This review will consider epidemiological studies and grey literature that report on the health risks of exposure to air pollution in areas where coal-fired power plants exist. ETHICS AND DISSEMINATION: All data will be collected from published and grey literature. Ethics approval is therefore not required. We will submit our findings for publication in a peer-reviewed journal.

Analysis of the quality of tunnel roof topography by automatic cutting control under the coupling of multiple factors.

The automatic cutting of coal and rock surface morphology modeling based on the actual geological environment of coal mine underground excavation and mining is of great significance for improving the surface quality of coal and rock after cutting and enhancing the safety and stability of advanced support. To this end, using the principle of coordinate transformation, the kinematic trajectory of the cutting head of the tunneling machine is established, and the contour morphology of the cutting head under variable cutting technology is obtained. Then, based on the regenerative vibration theory of the cutting head, a dynamic model of the cutting head coal wall is established, and the coordinate relationship of the cutting head in the tunnel coordinate system under vibration induction is analyzed. Based on fractal theory and Z-MAP method, a simulation method for the surface morphology of coal and rock after cutting is proposed, which is driven by the cutting trajectory Under the coupling effect of cutting vibration induction and random fragmentation of coal and rock, simulation of the surface morphology of comprehensive excavation tunnels was conducted, and relevant experiments were conducted to verify the results. A 1:3 similarity experimental model of EBZ160 tunneling machine was used to build a cutting head coal and rock system cutting experimental platform for comparative experiments of cutting morphology. Furthermore, statistical methods were used to compare and evaluate the simulated roof with the actual roof. The results show that the relative errors between the maximum range of peaks and valleys, the peak skewness coefficient of height standard deviation, and the kurtosis coefficient of the actual roof are 1.3%, 24.5%, 16%, and 2.9%, respectively. Overall, this indicates that the surface morphology distribution characteristics of the simulated roof and the actual roof are similar, verifying the effectiveness of the modeling and simulation method proposed in this paper, and providing theoretical support for the design and optimization of advanced support in the future.

What is China's efficient power generation portfolio under carbon neutrality target? An empirical analysis considering flexibility and system cost.

Variable renewable energy (VRE) is the most promising form of primary generation under a carbon neutrality target due to its environmental benefits, incentive policy, and technological progress. However, the increasing proportion of VRE generation, such as solar and wind power, has sharply increased integration cost and reduced power grid stability. This study uses portfolio theory to investigate China's optimal power generation portfolio by 2050 considering flexibility constraint and system cost, including technical and integration costs. The results demonstrate that non-fossil-fuel power generation technologies have cost and emission reduction advantages over fossil-fuel-based technologies. VRE generation technologies must be developed in synergy with other forms of power generation when considering flexibility requirement and integration cost. A complete phase-out of fossil-fuel power generation technologies in China appears unlikely in the study period. Gas-fired and coal-fired power generation are the pillar forms of power generation to meet future flexibility needs.

Process design and techno-economic analysis of activated carbon derived from anthracite coal.

Activated carbon (AC), renowned for its versatile applications in water treatment, air purification, and industrial processes, is a critical component in environmental remediation and resource recovery strategies. This study encompasses the process modeling of AC production using anthracite coal as a precursor, involving multiple activation stages at different operating conditions, coupled with a detailed techno-economic analysis aimed at assessing the operational feasibility and financial viability of the plant. The economic analysis explores the investigation of economic feasibility by performing a detailed cashflow and sensitivity analysis to identify key parameters influencing the plant's economic performance, including raw material and energy prices, operational and process parameters. Capital and operational costs are meticulously evaluated, encompassing raw material acquisition, labor, energy consumption, and equipment investment. Financial metrics like Net Present Value (NPV), Internal Rate of Return (IRR), and payout period (POP) are employed, and the results show that AC selling price, raw material cost and plant capacity are the most influential parameters determining the plant's feasibility. The minimum AC production cost of 1.28 $/kg is obtained, corresponding to coal flow rate of 14,550 kg/h. These findings provide valuable insights for stakeholders, policymakers, and investors seeking to engage in activated carbon production from anthracite.

Associations of coal mine dust exposure with arterial stiffness and atherosclerotic cardiovascular disease risk in chinese coal miners.

OBJECTIVE: Whether coal mine dust exposure increases cardiovascular diseases (CVDs) risk was rarely explored. Our objective was to examine the association between coal mine dust exposure and cardiovascular risk. METHODS: We estimated cumulative coal mine dust exposure (CDE) for 1327 coal miners by combining data on workplace dust concentrations and work history. We used brachial-ankle pulse wave velocity (baPWV, a representative indicator of arterial stiffness) and ten-year atherosclerotic cardiovascular disease (ASCVD) risk to assess potential CVD risk, exploring their associations with CDE. RESULTS: Positive dose-response relationships of CDE with baPWV and ten-year ASCVD risk were observed after adjusting for covariates. Specifically, each 1 standard deviation (SD) increase in CDE was related to a 0.27 m/s (95% CI: 0.21, 0.34) increase in baPWV and a 1.29 (95% CI: 1.14, 1.46) elevation in OR (odds ratio) of risk of abnormal baPWV. Moreover, each 1 SD increase in CDE was associated with a 0.74% (95% CI: 0.63%, 0.85%) increase in scores of ten-year ASCVD and a 1.91 (95% CI: 1.62, 2.26) increase in OR of risk of ten-year ASCVD. When compared with groups unexposed to coal mine dust, significant increase in the risk of arterial stiffness and ten-year ASCVD in the highest CDE groups were detected. CONCLUSION: The study suggested that cumulative exposure to coal mine dust was associated with elevated arterial stiffness and ten-year ASCVD risk in a dose-response manner. These findings contribute valuable insights for cardiovascular risk associated with coal mine dust.

Environmental impact assessment of acidic coal gangue leaching solution on groundwater: a coal gangue pile in Shanxi, China.

With the continual advancement of coal resource development, the comprehensive utilization of coal gangue as a by-product encounters certain constraints. A substantial amount of untreated coal gangue is openly stored, particularly acidic gangue exposed to rainfall. The leaching effect of acidic solutions, containing heavy metal ions and other pollutants, results in environmental challenges such as local soil or groundwater pollution, presenting a significant concern in the current ecological landscape of mining areas. Investigating the migration patterns of pollutants in the soil-groundwater system and elucidating the characteristics of polluted solute migration are imperative. To understand the migration dynamics of pollutants and unveil the features of solute migration, this study focuses on a coal gangue dump in a mining area in Shanxi. Utilizing indoor leaching experiments and soil column migration experiments, a two-dimensional soil-groundwater model is established using the finite element method of COMSOL. This model quantitatively delineates the migration patterns of key pollutant components leached from coal gangue into the groundwater. The findings reveal that sulfate ions can migrate and infiltrate groundwater within a mere 7 years in the vadose zone of aeration. Moreover, the average concentration of iron ions in groundwater can reach approximately 58.3 mg/L. Convection, hydrodynamic dispersion, and adsorption emerge as the primary factors influencing pollution transport. Understanding the leaching patterns and environmental impacts of major pollutants in acidic coal gangue is crucial for predicting soil-groundwater pollution and implementing effective protective measures.

Study on the mechanism of action of methane production by co-fermentation of sludge and lignite.

To improve the methanogenic efficiency of lignite anaerobic fermentation and explore innovative approaches to sludge utilization, a co-fermentation technique involving lignite and sludge was employed for converting biomass into biomethane. Volatile suspended solids were introduced as a native enrichment of the sludge and mixed with lignite for fermentation. The synergistic fermentation mechanism between sludge and lignite for biomethane production was analyzed through biochemical methane potential experiments, measurement of various parameters pre- and post-fermentation, observation of bacterial population changes during the peak of reaction, carbon migration assessment, and evaluation of rheological characteristics. The results showed that the addition of sludge in the anaerobic fermentation process improved the microorganisms' ability to degrade lignite and bolstered biomethane production. Notably, the maximum methane production recorded was 215.52 mL/g-volatile suspended solids, achieved at a sludge to coal ratio of 3:1, with a synergistic growth rate of 25.37%. Furthermore, the removal rates of total suspended solids, and total chemical oxygen demand exhibited an upward trend with an increasing percentage of sludge in the mixture. The relative abundance and activity of the methanogens population were found to increase with an appropriate ratio of sludge to lignite. This observation confirmed the migration of carbon between the solid-liquid-gas phases, promoting enhanced system affinity. Additionally, the changes in solid-liquid phase parameters before and after the reaction indicated that the addition of sludge improved the system's degradation capacity. The results of the study hold significant implications in realizing the resource utilization of sludge and lignite while contributing to environmental protection endeavors.

Systematic review of alternative materials that improve retention of potentially toxic metals in soil/clay liners in waste disposal areas.

When soils available for the construction of liners do not display the characteristics necessary for a good performance, mixtures with other materials can be employed for achieving the desired quality. Several researchers have addressed those mixtures from either a geotechnical or a gas diffusion perspective, emphasizing low hydraulic conductivity. However, in recent years, growing attention has been drawn to the ability of liners to mitigate contamination. The literature lacks studies on the use of amendments for soil liners or cover systems to retain potentially toxic metals, which are important inorganic contaminants. This paper provides a systematic review of the literature considering publications available on Web of Science and SpringerLink databases between January 1st, 2012, and December 5th, 2022. The aim of the review was to identify the types of soils and amendments studied as liners or cover systems for such retention of potentially toxic metals, the methodologies of application of the alternative materials in the soils, and the research gaps and perspectives in the field. Seventeen papers that addressed 31 materials as amendments were retrieved. The most studied amendment was coal fly ash, and 17 amendments were residues or by-products, which indicates concerns over waste destination and sustainability. Among the potentially toxic metals analyzed are Pb, Cu, and Cd. Gaps such as lack of pilot, field-scale, and long-term studies, as well as perspectives for future research (e.g., different liner configurations, concomitant mixtures of two or more materials in the soil, and focus on the sustainability of amendments), were identified.