Asbestos exposures associated with the use and handling of drilling mud additives.

This paper summarizes historical asbestos exposure data collected during the handling of short-fiber chrysotile asbestos that was used as an additive to drilling fluid in oil and gas exploration. A total of 1171 industrial hygiene (IH) personal and area air samples were collected and analyzed from more than 20 drilling rigs between 1972 and 1985. The dataset consists of 1097 short-term samples (<240 min) with more than 80% having sample durations less than 30 min. Average airborne fiber concentrations measured during asbestos handling activities ranged from 0.62 f/cc to 3.39 f/cc using phase-contrast microscopy (PCM). An additional 14 samples were considered long-term samples (>240 min) and there were 60 samples with no reported sample duration. Eight-hour time-weighted average (8-h TWA) results, calculated using short-term samples, along with long-term samples greater than 240 min, did not exceed contemporaneous Occupational Safety and Health Administration (OSHA) permissible exposure limits (PELs). This analysis fills a data gap in the evaluation of asbestos exposures from the use of drilling mud additives (DMAs) that contained chrysotile asbestos.

The refinery of the future.

Fossil fuels-coal, oil and gas-supply most of the world's energy and also form the basis of many products essential for everyday life. Their use is the largest contributor to the carbon dioxide emissions that drive global climate change, prompting joint efforts to find renewable alternatives that might enable a carbon-neutral society by as early as 2050. There are clear paths for renewable electricity to replace fossil-fuel-based energy, but the transport fuels and chemicals produced in oil refineries will still be needed. We can attempt to close the carbon cycle associated with their use by electrifying refinery processes and by changing the raw materials that go into a refinery from fossils fuels to carbon dioxide for making hydrocarbon fuels and to agricultural and municipal waste for making chemicals and polymers. We argue that, with sufficient long-term commitment and support, the science and technology for such a completely fossil-free refinery, delivering the products required after 2050 (less fuels, more chemicals), could be developed. This future refinery will require substantially larger areas and greater mineral resources than is the case at present and critically depends on the capacity to generate large amounts of renewable energy for hydrogen production and carbon dioxide capture.

Elevated fish densities extend kilometres from oil and gas platforms.

Thousands of offshore oil and gas platforms have been installed throughout the world's oceans and more structures are being installed as part of the transition to renewable energy. These structures increase the availability of ecological niches by providing hard substrate in midwater and complex 3D habitat on the seafloor. This can lead to 'hotspots' of biodiversity, or increased densities of flora and fauna, which potentially spill over into the local area. However, the distances over which these higher densities extend (the 'range of influence') can be highly variable. Fish aggregate at such structures, but the range of influence and any implications for wider fish populations, are unclear. We investigated the relationship between fish and platform areal densities using high resolution fisheries acoustic data. Data were collected in the waters surrounding the vessel exclusions zones around 16 oil and gas platforms in the North Sea, and throughout the wider area. We estimated densities of schooling fish using echo-integration, and densities of non-schooling fish using echo-counting. At 10 platforms, non-schooling fish densities were elevated near the platform relative to background levels in the equivalent wider area. The range of influence, defined here as the range to which fish densities were elevated above background, varied from 0.8 to 23 km. In areas of high platform density, fish schools were encountered more often, and non-schooling fish densities were higher, when controlling for other sources of environmental variation. This is the first time such long-range effects have been identified; previously, ranges of influence have been reported in the order of just 10s-100s of metres. These findings suggest that the environmental impact of these structures may extend further than previously thought, which may be relevant in the context of upcoming management decisions around the decommissioning of these structures.

The impact of ozone treatment on the removal effectiveness of various refractory compounds in wastewater from petroleum refineries.

Large volumes of wastewater are generated during petroleum refining processes. Petroleum refinery wastewater (PRW) can contain highly toxic compounds that can harm the environment. These toxic compounds can be a challenge in biological treatment technologies due to the effects of these compounds on microorganisms. These challenges can be overcome by using ozone (O3) as a standalone or as a pretreatment to the biological treatment. Ozone was used in this study to degrade the organic pollutants in the heavily contaminated PRW from a refinery in Mpumalanga province of South Africa. The objective was achieved by treating the raw PRW using ozone at different ozone treatment times (15, 30, 45, and 60 min) at a fixed ozone concentration of 3.53 mg/dm3. The ozone treatment was carried out in a 2-liter custom-designed plexiglass cylindrical reactor. Ozone was generated from an Eco-Lab-24 corona discharge ozone generator using clean, dry air from the Afrox air cylinder as feed. The chemical oxygen demand, gas chromatograph characterization, and pH analysis were performed on the pretreated and post-treated PRW samples to ascertain the impact of the ozone treatment. The ozone treatment was effective in reducing the benzene, toluene, ethylbenzene, and xylenes (BTEX) compounds in the PRW. The 60-min ozone treatment of different BTEX pollutants in the PRW resulted in the following percentage reduction: benzene 95%, toluene 77%, m + p-xylene 70%, ethylbenzene 69%, and o-xylene 65%. This study has shown the success of using ozone in reducing the toxic BTEX compounds in a heavily contaminated PRW.

Comparison of numerical calculations and ALOHA modeling in consequence assessment of chlorine gas emissions from ethylene dichloride reactors.

Incidents involving chemical storage tanks in the petrochemical industry are significant events with severe consequences. Within the petrochemical industry, EDC is a sector that produces ethylene dichloride through the reaction of chlorine and ethylene. The present research was conducted to evaluate the consequences of chlorine gas released from the EDC reactor in a petrochemical industry in southern Iran. Data regarding reactor specifications were obtained from the factory's technical office, while climatic data was acquired from the Meteorological Organization. The consequences of chlorine gas release from the reactor were assessed in four predefined scenarios using numerical calculation methods and modeling with the ALOHA software. The numerical calculation method involved thermodynamic fluid path analysis, discharge coefficient calculations, and wind speed impact analysis. The hazard radius was determined based on the ERPG1-2-3 index. Results showed that in the scenario of chlorine gas release from EDC reactors, according to the ALOHA model, an increase in wind speed from 3 to 7 m/h led to an expanded dispersion radius. At a radius of 700 m from the reactor, the maximum outdoor concentration reached 3.12 ppm, decreasing to 2.27 ppm at 800 m and further to 1.53 ppm at 1000 m. The comparison of numerical calculations and modeling using the ALOHA software indicates the desirable conformity of the results with each other. The R2 coefficient for evaluating the conformity of the results was 0.9964, indicating the desired efficiency of the model in evaluating the consequences of the release of toxic gasses from the EDC tank. The results of this research can be useful in designing the site and emergency response plan.

Estimates of the global burden of cancer-related deaths attributable to residential exposure to petrochemical industrial complexes from 2020 to 2040.

The petrochemical industry is a major industrial emitter of greenhouse gas (CO2) and environmental pollution, posing health risks to nearby communities. Although previous studies have indicated that residents living near petrochemical industrial complexes are at a higher risk of cancer, they have focused on local or regional burdens. This study aimed to estimate the global cancer burden attributable to residential exposure to petrochemical industrial complexes. The geographical coordinates of petrochemical plants and oil refineries were retrieved and verified from published sources. The ArcGIS software and global population data were used to estimate the number of people living within specific distances (exposed population). The exposure time window was framed as ranging from 1992 to 2035, extending to the latest period of the exposure time window for all cancer types to estimate the attributable deaths between 2020 and 2040. The relative risk of cancer was estimated from 15 published studies. Population attributable fraction (PAF) method was used to estimate the risk of cancer attributable to residential exposure and calculate the number of cancer-related deaths. Our findings indicate that >300 million people worldwide will be estimated to live near petrochemical industrial complexes by 2040. The overall global burden of cancer-related deaths was 19,083 in 2020, and it is estimated to increase to 27,366 deaths by 2040. The region with the highest attributable cancer deaths due to exposure is the high-income region, which had 10,584 deaths in 2020 and is expected to reach 13,414 deaths by 2040. Residential exposure to petrochemical industrial complexes could contribute to global cancer deaths, even if the proportion is relatively small, and proactive measures are required to mitigate the cancer burdens among these residents. Enforcing emissions regulations, improving monitoring, educating communities, and fostering collaboration are vital to protecting residents' health.

Simultaneous removal of crude oil and heavy metals by highly adapted bacterial strain Cutibacterium sp. NL2 isolated from Algerian oilfield

Investigating the ability of bacteria to simultaneously enhance hydrocarbon removal and reduce heavy metals’ toxicity is necessary to design more effective bioremediation strategies. A bacterium (NL2 strain) isolated from an Algerian oilfield was cultivated on crude oil as sole carbon and energy sources. Molecular analyses of the 16S rRNA gene sequence placed the strain within the Cutibacterium genera. This isolate was able to tolerate up to 60% of crude oil as sole carbon source. Chemical analyses (GC-MS) evidenced that strain NL2 was able to degrade 92.22% of crude oil (at optimal growing conditions: pH 10, 44 °C, 50 g L−1 NaCl, and 20% of crude oil (v/v) as sole carbon source) in only 7 days. NL2 isolate was also able to produce biosurfactants with reduction of surface tension of growing media (29.4 mN m−1). On the other hand, NL2 strain was able to tolerate high lead (Pb) and copper (Cu) concentrations (up to 60 mM). In fact, NL2 cultivated in the presence of 20% of crude oil, and 0.48 mM of Pb was able to reduce Pb concentration by a 41.36%. In turn, when cultivated on high Pb concentration (15 mM), the strain was able to remove 35.19% of it and 86.25% of crude oil, both in a time frame of 7 days. Our findings suggest that Cutibacterium strain NL2 is able to efficiently use and remove a wide range of crude oil substrates in presence of high Pb concentration. Accordingly, NL2 strain is of extreme interest from a biotechnological standpoint. (AU)

Coalescence of multiple droplets induced by a constant DC electric field.

In this work, the electro-coalescence process of three nanodroplets under a constant DC electric field is investigated via molecular dynamics simulations (MD), aiming to explore the electric manipulation of multiple droplets coalescence on the molecular level. The symmetrical and asymmetrical dynamic evolutions of electrocoalescence process can be observed. Our MD simulations show that there are two types of critical electric fields to induce the special dynamics. The chain configuration can be formed, when one of the critical electric field is exceeded, referred to as Ecc. On the other hand, there is another critical electric field to change the coalescence pattern from complete coalescence to partial coalescence, the so-called Ecn. Finally, we find that the use of the pulsed DC electric field can overcome the drawbacks of the constant DC electric field in the crude oil industry, and the mechanisms behind the suppressed effect of the water chain or non-coalescence are further revealed.

[Aftershocks; about the psychological consequences of gas extraction in Groningen]. / Naschokken; over de psychische gevolgen van de gaswinning in Groningen.

BACKGROUND: In recent decades, gas extraction in Groningen has led to a lot of material and immaterial damage, including much psychological suffering, which was ignored by policymakers for years. With the publication of the report of the Parliamentary Inquiry into Natural Gas Extraction in Groningen, this is recognized and suggestions are made to repair the damage caused in the broadest sense. AIM: Description of current and expected psychological consequences, and research and treatment to be conducted focused on this specific regional phenomenon. METHOD: Describing the Groningen situation based on various sources, and identifying current and expected mental consequences based on currently available data and scientific literature. RESULTS: Psychological consequences are largely known and identified, but not yet quantified. It is most important for the well-being of inhabitants that the government takes its care task seriously and supports victims in a practical sense. Subsequently, a targeted treatment offer must be developed. CONCLUSION: The knowledge available within psychiatry and psychology about the development and treatment of psychological complaints should play a role in researching and improving the well-being and the mental health of those affected by the gas extraction problem, now and in the future.

Reliable sustainable management strategies for flare gas recovery: technical, environmental, modeling, and economic assessment: a comprehensive review.

The gas flaring network is an inseparable constituent commonly present in most of the oil and gas refineries and petrochemical facilities conferring reliable operational parameters. The improper disposal of burn-off gases improperly results in environmental problems and loss of economic resources. In this regard, waste to energy transforming nexus, in accord with the "carbon neutrality" term, has potentially emerged as a reasonable pathway to preserve our planet. In a transdisciplinary manner, the present review article deeply outlines the different up-to-date strategies developed to recover the emitted gases (flaring minimization) into different value-added products. To analyze the recovery potential of flare gases, different technologies, and decision-making factors have been critically reviewed to find the best recovery methods. We recommend more straightforward recovery methods despite lower profits. In this regard, electricity generation seems to be an appropriate option for application in small amounts of flaring. However, several flare gas utilization processes such as syngas manufacturing, reinjection of gas into petroleum reservoirs, and production of natural gas liquid (NGL) are also recommended as options because of their economic significance, technological viability (both onshore and offshore), and environmental benefits. Moreover, the adopted computational multi-scale data assimilation for predictive modeling of flare gas recovery scenarios has been systematically reviewed, summarized, and inspected.

Human performance and automated operations: a regulatory perspective.

Increased levels of digitalisation present major opportunities for efficiency in the oil and gas industry but can also contribute to new risks and vulnerabilities. Based on developments in the industry, the Norwegian Ocean Industry Authority (HAVTIL) has in recent years pursued targeted knowledge development and follow-up of company's digitalisation initiatives. This paper explores data collected through HAVTIL's audits of the development and use of automated systems within well operations. The analysis of the data resulted in the identification of five main topics related to the implementation of digital technologies. The five main topics were organisational complexity, follow-up and implementation of technology, analysis and documentation, user-interface and alarms and competence and training. Overall, the results support research findings within human factors and technology development, pointing out that there is a lack of focus on human factors in both development projects and in operations. In addition, this paper provides insight into how digitalisation initiatives are followed-up and explores the results from the analysis in light of the current developments in the industry.

To investigate automated operations and human performance, three audits were performed by the Norwegian Ocean Industry Authority (HAVTIL). These audits have been used as case studies and the basis for this paper. Results from the analysis support research findings within the field of human factors and technology development, pointing out that there is a lack of focus on human factors in both development projects and in operations.

Multivariate analysis of carcinogenic equivalence (CEQ) to characterize carcinogenic VOC emissions in a typical petrochemical industrial park in Taiwan.

Large industrial emissions of volatile organic compounds (VOCs) from the petrochemical industry are a critical concern due to their potential carcinogenicity. VOC emissions vary in composition depending on the source and occur in mixtures containing compounds with varying degrees of toxicity. We proposed the use of carcinogenic equivalence (CEQ) and multivariate analysis to identify the major contributors to the carcinogenicity of VOC emissions. This method weights the carcinogenicity of each VOC by using a ratio of its cancer slope factor to that of benzene, providing a carcinogenic equivalence factor (CEF) for each VOC. We strategically selected a petrochemical industrial park in southern Taiwan that embodies the industry's comprehensive nature and serves as a representative example. The CEQs of different emission sources in three years were analyzed and assessed using principal component analysis (PCA) to characterize the major contributing sectors, vendors, sources, and species for the carcinogenicity of VOC emissions. Results showed that while the study site exhibited a 20.7 % (259.8 t) decrease in total VOC emissions in three years, the total CEQ emission only decreased by 4.5 % (15.9 t), highlighting a potential shift in the emitted VOC composition towards more carcinogenic compounds. By calculating CEQ followed by PCA, the important carcinogenic VOC emission sources and key compounds were identified. More importantly, the study compared three approaches: CEQ followed by PCA, PCA followed by CEQ, and PCA only. While the latter two methods prioritized sources based on emission quantities, potentially overlooking less abundant but highly carcinogenic compounds, the CEQ-first approach effectively identified vendors and sources with the most concerning cancer risks. This distinction underscores the importance of selecting the appropriate analysis method based on the desired focus. Our study highlighted how prioritizing CEQ within the analysis framework empowered the development of precise control measures that address the most carcinogenic VOC sources.

Investigating the effects of age, task load, task complexity, and input device on monitoring performance for smart manufacturing in the oil refining industry.

Human beings play an important role in a smart manufacturing economy. In this study, we explored the effects of age, task load, task complexity, and input device on abnormal event detection performance in an oil refinery control room task. Thirty participants were recruited to complete a process plant monitoring task in which they were asked to continuously monitor the gauge states, and immediately detect and solve the abnormal events. Participants' accuracy in detecting abnormal states was recorded and analysed during the task. We found that the complexity factor affected accuracy significantly, and younger adults had significantly higher accuracy than older adults in high task load trials. No significant effect was found for the input device factor. These findings suggest that age, task load, and task complexity should be taken into consideration when designing tools to improve older operators' performance.Practitioner summary: The smart manufacturing economy elicits higher requirements for older operators in oil refinery monitoring tasks. Under high task load, older adults had lower accuracy in detecting abnormal conditions than younger adults. The task complexity affected participants' accuracy in detecting abnormal states.

Levels and control of welding fume exposure to total particulate, hexavalent chromium, and manganese in contracted activities in an oil refinery setting (2008-2018).

In response to increasing focus on occupational exposures to welding fume, a 10-year series of personal exposure measurements was analyzed for the two main welding processes (Shielded Metal Arc Welding or Stick and Tungsten Inert Gas welding or TIG) used in an oil refinery setting. Exposures from ancillary gouging and grinding were also analyzed. The operations were conducted under a permit-to-work system, which stipulated control measures in the form of ventilation and respiratory protective equipment (RPE) depending on the work environment, base metal, and welding process. The analysis focused on three health hazards of interest: total particulate (TP); hexavalent chromium (Cr (VI)); and manganese (Mn). The study's aims were the analysis of exposure levels related to operational conditions to verify the adequacy of required control measures and the generation of quantitative information for the development of predictive exposure models. Arithmetic mean exposures were 2.01 mg/m3 for TP (n = 94), 13.86 µg/m3 for Cr (VI) (n = 160), and 0.024 mg/m3 for Mn (n = 95). Requirements and practices for ventilation and use of RPE appeared adequate for maintaining exposure levels below maximum use concentrations. Predictive models for mean exposure levels were developed using multiple linear regression. Different patterns emerged for TP, Cr (VI), and Mn exposure determinants. Enclosed or confined work environments were associated with elevated exposure levels, regardless of the provision of local exhaust or general dilution ventilation. Carbon arc, used with gouging and grinding, contributed significantly to TP exposure (p = 0.006). The relative TP source strengths of the two main welding processes were comparable to the literature data. For Cr (VI), stick welding was associated with approximately 50-fold (p < 0.001) higher exposure potential than TIG welding. For Mn, this difference was approximately 2.5-fold. Differences were observed across the three analytes in exposure reduction efficiency of local exhaust ventilation (LEV) compared to natural ventilation, possibly due to ineffective use in confined spaces. These findings contribute to the overall understanding of TP, Cr (VI), and Mn exposures from welding and required controls in an oil refinery setting.

Framework for the assessment of the safety culture in the oil and gas industry.

Approaches to safety culture assessment may have many limits if supported exclusively by quantitative methods. Based on this, a research team developed a quantitative-qualitative approach to assess the maturity of the safety culture on an oil platform. To that end, the team sought to develop and test a method consisting of an initial ethnographic phase followed by four other distinct phases: definition of homogeneous groups; production of customized questionnaires; quantitative evaluation; and qualitative assessment. The results show the emergence of trends, from pre-defined themes in safety culture to specific levels of maturity for each of the homogeneous groups. At the same time, it was perceived that the maturity level of the groups is defined from the daily work practices developed by each one of them. This experience allowed us to propose a framework for assessing the maturity levels of safety culture for the oil and gas industry.

Is residential exposure to oil refineries a novel contextual risk factor for coronary heart disease?

Despite a multi-decade decrease in cardiovascular disease, geographic disparities have widened, with excess mortality concentrated within the United States (U.S.) South. Petroleum production and refining, a major contributor to climate change, is concentrated within the U.S. South and emits multiple classes of atherogenic pollutants. We investigated whether residential exposure to oil refineries could explain variation in self-reported coronary heart disease (CHD) prevalence among adults in southern states for the year 2018, where the majority of oil refinery activity occurs (Alabama, Mississippi, Louisiana, Arkansas, Texas, New Mexico, and Oklahoma). We examined census tract-level association between oil refineries and CHD prevalence. We used a double matching method to adjust for measured and unmeasured spatial confounders: one-to-n distance matching and one-to-one generalized propensity score matching. Exposure metrics were constructed based on proximity to refineries, activities of refineries, and wind speed/direction. For all census tracts within 10 km of refineries, self-reported CHD prevalence ranged from 1.2% to 17.6%. Compared to census tracts located at ≥5 km and <10 km, one standard deviation increase in the exposure within 5 km of refineries was associated with a 0.33 (95% confidence interval: 0.04, 0.63) percentage point increase in the prevalence. A total of 1119.0 (123.5, 2114.2) prevalent cases or 1.6% (0.2, 3.1) of CHD prevalence in areas within 5 km from refineries were potentially explained by exposure to oil refineries. At the census tract-level, the prevalence of CHD explained by exposure to oil refineries ranged from 0.02% (0.00, 0.05) to 47.4% (5.2, 89.5). Thus, although we cannot rule out potential confounding by other personal risk factors, CHD prevalence was found to be higher in populations living nearer to oil refineries, which may suggest that exposure to oil refineries can increase CHD risk, warranting further investigation.

Characterization and treatment of oily sludge: A systematic review.

Oily sludge is a prevalent hazardous waste generated in the petroleum industry, and effectively treating it remains a key challenge for the petroleum and petrochemical sectors. This paper provides an introduction to the origin, properties, and hazards of oil sludge while summarizing various treatment methods focused on reduction, recycling, and harmlessness. These methods include combustion, stabilization/solidification, oxidation and biodegradation techniques, solvent extraction, centrifugation, surfactant-enhanced oil recovery processes as well as freezing-thawing procedures. Additionally discussed are pyrolysis, microwave radiation applications along with electrokinetic method utilization for oily sludge treatment. Furthermore explored are ultrasonic radiation techniques and froth flotation approaches. These technologies have been thoroughly examined through discussions that analyze their process principles while considering influencing factors as well as advantages and disadvantages associated with each method. Based on the characteristics of oily sludge properties and treatment requirements, a selection methodology for choosing appropriate oily sludge treatment technology is proposed in this study. The development direction of processing technology has also been explored to provide guidance aimed at improving efficiency by optimizing existing processing technologies. The paper presents a comprehensive treatment method for oily sludge, ensuring that all the parameters meet the standard requirements.

An examination of the Petroleum Industry Act 2021: prospects, challenges, and the way forward.

Background: The study examines the gaps in the provisions of the Petroleum Industry Act (PIA) that could hinder the effective application of the Act in attaining its objectives. The repealed Petroleum Act of 1969 became obsolete and largely incapable of meeting the emerging global best practices in the industry due to inadequate sanctions, failure to address the aspirations of the people of the oil-bearing states, among others. Hence, the need for the PIA of 2021 to overhaul the industry to meet global standards though some controversial provisions that pose challenges to its proper implementation. Methods: The study examines the PIA to identify its prospects, challenges, and the way forward. The methodology the study utilises is doctrinal research with reports from existing literature and tertiary data sources such as newspapers, the Internet, and websites. Pertinent data collected from these sources were theoretically analysed and argued with current literature on the subject. Results: The finding is that the PIA does not make adequate provisions for the energy transition in line with Nigeria's Nationally Determined Contributions (NDC) under the Paris agreement; the PIA was provided for weak institutions, which translates to weak implementation and enforcement of the law which further widening the gap between the law and reality. Conclusions: The study concluded that, although the Act delivered the much-needed stability in the petroleum industry in Nigeria, there is a need for an overhaul of the Act to further protect the interest of host communities and allow for co-ownership of petroleum resources by the state government.