Alkyl pyrazine synthesis via an open heated bath with variable sugars, ammonia, and various amino acids.

BACKGROUND: Semi-quantitative characteristics of headspace volatile pyrazines which constituted around 1% by weight of the final product have been previously described. The influence of reactant concentration, reaction temperature, and reaction time on both the yield of total alkyl pyrazines and the distribution pattern of specific identified pyrazines has not been reported. RESULTS: The optimum synthetic conditions were 5 mol L-1 NH4 OH, 2 mol L-1 rhamnose, 0.5 mol L-1 leucine at 110°C for 2 h. The greatest total amount of pyrazines obtained was 17 280 µg of extracted product which translated into 31% 2,6-dimethyl pyrazine, 17% 2-methyl pyrazine, 15% 2-ethyl-6-methyl pyrazine, and 16% 2-isoamyl-6-methyl pyrazine. CONCLUSION: The yield of synthesized pyrazines increased at higher temperatures. Quantitative total and specific pyrazine results as opposed to analysis of only headspace volatiles are more representative of pyrazine synthesis. © 2016 Society of Chemical Industry.

Application of response surface methodology for the optimization of supercritical fluid extraction of essential oil from pomegranate (Punica granatum L.) peel.

Essential oils and volatile components of pomegranate (Punica granatum L.) peel of the Malas variety from Meybod, Iran, were extracted using supercritical fluid extraction (SFE) and hydro-distillation methods. The experimental parameters of SFE that is pressure, temperature, extraction time, and modifier (methanol) volume were optimized using a central composite design after a (24-1) fractional factorial design. Detailed chemical composition of the essential oils and volatile components obtained by hydro-distillation and optimum condition of the supercritical CO2 extraction were analyzed by GC-MS, and seventy-three and forty-six compounds were identified according to their retention indices and mass spectra, respectively. The optimum SFE conditions were 350 atm pressure, 55 °C temperature, 30 min extraction time, and 150 µL methanol. Results showed that oleic acid, palmitic acid and (-)-Borneol were major compounds in both extracts. The optimum extraction yield was 1.18 % (w/w) for SFE and 0.21 % (v/w) for hydro-distillation.

Porous-membrane-protected polyaniline-coated SBA-15 nanocomposite micro-solid-phase extraction followed by high-performance liquid chromatography for the determination of parabens in cosmetic products and wastewater.

A SBA-15/polyaniline para-toluenesulfonic acid nanocomposite supported micro-solid-phase extraction procedure has been developed for the extraction of parabens (methylparaben, ethylparaben, and propylparaben) from wastewater and cosmetic products. The variables of interest in the extraction process were pH of sample, sample and eluent volumes, sorbent amount, salting-out effect, extraction and desorption time, and stirring rate. A Plackett-Burman design was performed for the screening of variables in order to determine the significant variables affecting the extraction efficiency. Then, the significant factors were optimized by using a central composite design. The optimum experimental conditions found at 50 mL sample solution, extraction and desorption times of 40 and 20 min, respectively, 500 µL of 3% v/v acetic acid in methanol as eluent, 0.01 M salt addition, and 10 mg of the sorbent. Under the optimum conditions, the developed method provided detection limits in the range of 0.08-0.4 ng/mL with good repeatability (RSD% < 7) and linearity (r(2) = 0.997-0.999) for the three parabens. Finally, this fast and efficient method was employed for the determination of target analytes in cosmetic products and wastewater, and satisfactory results were obtained.

Optimization of supercritical fluid extraction of essential oils and fatty acids from flixweed (Descurainia Sophia L.) seed using response surface methodology and central composite design.

Essential oils and fatty acids of Descurainia sophia L. seed were obtained by supercritical CO2 extraction and steam distillation methods. The effect of different parameters such as pressure, temperature, modifier volume, dynamic and static extraction timeon the extraction yield were optimized using a central composite design after a 2 (n-1) fractional factorial design. The results showed that under the pressure of 355 bar, temperature of 65 °C, methanol volume of 150 µL, dynamic and static extraction times of 35 and 10 min, respectively, the major components were methyl linoleate (18.2 %), camphor (12.32 %), cis-thujone (11.3 %) and trans-caryophyllene (9.17 %). The results indicated that by using the proper conditions, the supercritical fluid extraction is more selective than the steam distillation method. Extraction yields based on supercritical fluid extraction varied in the range of 0.68 to 17.1 % (w/w), and the extraction yield based on the steam distillation was 0.25 % (v/w).

Low-voltage electrochemically stimulated stir membrane liquid-liquid microextraction as a novel technique for the determination of methadone.

In the present work, for the first time, a new portable setup was designed, developed and presented for the extraction of methadone, as a basic drug model from biological fluid samples using a low-voltage electrically stimulated stir membrane liquid-liquid microextraction technique (LV-ESSM-LLME), followed by high-performance liquid chromatography with ultraviolet detection. This new approach combines the advantages of stir membrane liquid-liquid microextraction and electrokinetic migration in the same unit under soft electrochemical conditions in a portable device, allowing for the isolation and preconcentration of the target analyte in a simple and efficient manner under three-phase mode. To investigate the influence of external stirring and the application of electrical potential as the driving force, a comparative study of all variables involved in the extraction process was carried out using the low-voltage electromembrane extraction (LV-EME) and LV-ESSM-LLME methods. Under soft electrokinetic migration conditions, methadone was transported from an acidic sample solution (pH 4.0), through the NPOE immobilized in the pores of the porous polypropylene sheet membrane, and into 25µL of 10mmolL-1 HCl acceptor solution with a stirring rate of 1000rpm and 700rpm after 15min and 20min for LV-ESSM-LLME and LV-EME, respectively. Under the optimized conditions, preconcentration factors in the range of 17-24 and 21.5-29 for LV-EME and LV-ESSM-LLME, respectively, were considered, and satisfactory repeatability (4.5<[RSD]<7.5) was obtained in different matrices. The obtained relative recoveries of the target analyte were in the range of 87-94% and 93-101% for LV-EME and LV-ESSM-LLME, respectively, which indicated the excellent capability of the developed methods to extract methadone from complex matrices.

Carrier mediated transport solvent bar microextraction for preconcentration and determination of dexamethasone sodium phosphate in biological fluids and bovine milk samples using response surface methodology.

In the current study, a fast and simple preconcentration and sample clean up procedure was developed based on carrier mediated three phase solvent bar liquid phase microextraction (TPSB-LPME) method prior to high performance liquid chromatography (HPLC) equipped with an ultraviolet (UV) absorbance detector for simultaneous extraction and determination of trace amounts of dexamethasone sodium phosphate (DSP) in human plasma, human urine and bovine milk. According to this procedure, dexamethasone sodium phosphate was extracted from an acidic aqueous sample (SP, 7.5mL with pH=6) into the organic solvent 1-octanol (containing 5%, w/v of Aliquat-336 as carrier) residing in the pores of a hollow fiber and then back extracted into an alkali receiving phase (RP, 5µL of 0.65M NaClO4 with pH=10) was located inside the lumen of the fiber. After the extraction period, the receiving phase was directly injected into HPLC. The effect of different extraction conditions (i.e., pH of source and receiving phases, ionic strength, stirring rate, counter-ion concentration and extraction time) on the extraction efficiency of DSP was investigated and optimized using central composite design (CCD) as a powerful tool. Under the optimal conditions, preconcentration factor of 320, extraction recovery of 23%, dynamic linear range of 1-1000ngmL(-1) (r(2)=0.997) and limit of detection of 0.1ngmL(-1) were obtained. Eventually, applicability of the proposed method was successfully confirmed by extraction and determination of drug in plasma and urine samples and bovine milk with R.S.D.s<8%. Comparing to the traditional methods, the proposed method exhibits high sensitivity and high preconcentration factors as well as good precision. The extraction setup is simple and due to active transport of analytes, high cleanup effect and good selectivity are obtained in the extraction process. This extraction technique is also the most economical sample preparation and preconcentration technique as compared to traditional extraction techniques.

Comparison of supercritical fluid extraction and ultrasound-assisted extraction of fatty acids from quince (Cydonia oblonga Miller) seed using response surface methodology and central composite design.

Fatty acids of Cydonia oblonga Miller cultivated in Iran were obtained by supercritical (carbon dioxide) extraction and ultrasound-assisted extraction methods. The oils were analyzed by capillary gas chromatography using mass spectrometric detections. The compounds were identified according to their retention indices and mass spectra (EI, 70eV). The experimental parameters of SFE such as pressure, temperature, modifier volume, static and dynamic extraction time were optimized using a Central Composite Design (CCD) after a 2(5) factorial design. Pressure and dynamic extraction time had significant effect on the extraction yield, while the other factors (temperature, static extraction time and modifier volume) were not identified as significant factors under the selected conditions. The results of chemometrics analysis showed the highest yield for SFE (24.32%), which was obtained at a pressure of 353bar, temperature of 35°C, modifier (methanol) volume of 150µL, and static and dynamic extraction times of 10 and 60min, respectively. Ultrasound-assisted extraction (UAE) of Fatty acids from C. oblonga Miller was optimized, using a rotatable central composite design. The optimum conditions were as follows: solvent (n-hexane) volume, 22mL; extraction time, 30min; and extraction temperature, 55°C. This resulted in a maximum oil recovery of 19.5%. The extracts with higher yield from both methods were subjected to transesterification and GC-MS analysis. The results show that the oil obtained by SFE with the optimal operating conditions allowed a fatty acid composition similar to the oil obtained by UAE in optimum condition and no significant differences were found. The major components of oil extract were Linoleic, Palmitic, Oleic, Stearic and Eicosanoic acids.