Atom Probe Tomography Investigation of Clustering in Model P2O5-Doped Borosilicate Glasses for Nuclear Waste Vitrification.

Atom probe tomography (APT) has been utilized to investigate the microstructure of two model borosilicate glasses designed to understand the solubility limits of phosphorous pentoxide (P2O5). This component is found in certain high-level radioactive defence wastes destined for vitrification, where phase separation can potentially lead to a number of issues relating to the processing of the glass and its long-term chemical and structural stability. The development of suitable focused ion beam (FIB)-preparation routes and APT analysis conditions were initially determined for the model glasses, before examining their detailed microstructures. In a 3.0 mol% P2O5-doped glass, both visual inspection and sensitive statistical analysis of the APT data show homogeneous microstructures, while raising the content to 4.0 mol% initiates the formation of phosphorus-enriched nanoscale precipitates. This study confirms the expected inhomogeneities and phase separation of these glasses and offers routes to characterizing these at near-atomic scale resolution using APT.

Toward a Unifying Hypothesis for Redesigned Lipid Catabolism as a Clinical Target in Advanced, Treatment-Resistant Carcinomas.

We review extensive progress from the cancer metabolism community in understanding the specific properties of lipid metabolism as it is redesigned in advanced carcinomas. This redesigned lipid metabolism allows affected carcinomas to make enhanced catabolic use of lipids in ways that are regulated by oxygen availability and is implicated as a primary source of resistance to diverse treatment approaches. This oxygen control permits lipid catabolism to be an effective energy/reducing potential source under the relatively hypoxic conditions of the carcinoma microenvironment and to do so without intolerable redox side effects. The resulting robust access to energy and reduced potential apparently allow carcinoma cells to better survive and recover from therapeutic trauma. We surveyed the essential features of this advanced carcinoma-specific lipid catabolism in the context of treatment resistance and explored a provisional unifying hypothesis. This hypothesis is robustly supported by substantial preclinical and clinical evidence. This approach identifies plausible routes to the clinical targeting of many or most sources of carcinoma treatment resistance, including the application of existing FDA-approved agents.

Multiperspective Analysis of Pandemic Impacts on U.S. Import Trade: What Happened, and Why?

U.S. container ports have experienced unpresented congestion since mid-2020. The congestion is generally attributed to import surges triggered by heavy spending on consumer goods during the COVID-19 pandemic. Port congestion has been compounded by the inability of importers to retrieve, receive, and process all the inbound goods they have ordered, resulting in supply chain shortfalls and economic disruption. How can the shipping industry and government organizations predict the end of the current surge and anticipate future surges? Expected seasonal variations in import volume are associated with peak holiday shopping periods; nonseasonal import surges are signaled by other factors. The research goes beyond transportation data sources to examine broader connections between import volume and indicators of economic and retail industry conditions. The strongest and most useful relationship appears to be between retail inventory indicators and containerized import growth. From January 2018 through July 2021, there was a relatively strong negative correlation between retail inventory- and import TEU indices with a 4-month lag (corresponding roughly to the time between import orders and -arrival). In the 2020 to 2021 pandemic period the negative correlation was stronger, again with a 4-month lag. These findings suggest that observers might anticipate import surges after marked, nonseasonal drops in retail inventories, and that import surges are likely to last until target inventory levels are restored. In a broader sense, an awareness of the linkages between consumer demand, retail chain responses, and containerized import volumes could better inform port, freight transportation, and government planning and policy choices.

Elucidating the Mechanistic Origin of a Spin State-Dependent FeNx-C Catalyst toward Organic Contaminant Oxidation via Peroxymonosulfate Activation.

Atomically dispersed metals on nitrogen-doped carbon matrices have attracted extensive interest in the removal of refractory organic pollutants. However, a thorough exploration of the particular structure for each active site and specific effects of these sites still remains elusive. Herein, an Fe-pyridinic N4 structure in a single-atom catalyst (FeNx-C) was constructed using a facile pyrolysis strategy, and it exhibited superior catalytic activity in peroxymonosulfate (PMS) activation toward organic contaminant oxidation. The various Fe species and relative amounts of each Fe site in the FeNx-C catalyst were validated using X-ray absorption spectroscopy and 57Fe Mössbauer spectroscopy, which showed critical dependencies on the precursor ratio and calcination temperature. The positive correlations between relative content of high-spin state species (FeII and FeIII) and catalytic performance were found to determine the reactive species generation and electron transfer pathway in the FeNx-C/PMS system. Moreover, catalytic performance and theoretical calculation results revealed that FeII-N4 in the high-spin state (S = 2) tends to activate PMS to form sulfate and hydroxyl radicals via a one-electron transfer process, while the FeIII-N4 moiety (S = 5/2) is prone to high-valent iron species generation with lower free energy. Benefiting from finely tuned active sites, a single-atom FeNx-C catalyst achieved favorable applicability in actual wastewater treatment with efficient resistance of the common water matrix. The present work advances the mechanistic understanding of spin state-dependent persulfate activation in single-atom catalysts and provides guidance to design a superior catalyst based on spin state descriptions.

Complex Magnetic Ordering in the Oxide Selenide Sr2Fe3Se2O3.

Sr2Fe3Se2O3 is a localized-moment iron oxide selenide in which two unusual coordinations for Fe2+ ions form two sublattices in a 2:1 ratio. In the paramagnetic region at room temperature, the compound adopts the crystal structure first reported for Sr2Co3S2O3, crystallizing in space group Pbam with a = 7.8121 Å, b = 10.2375 Å, c = 3.9939 Å, and Z = 2. The sublattice occupied by two-thirds of the iron ions (Fe2 site) is formed by a network of distorted mer-[FeSe3O3] octahedra linked via shared Se2 edges and O vertices forming layers, which connect to other layers by shared Se vertices. As shown by magnetometry, neutron powder diffraction, and Mössbauer spectroscopy measurements, these moments undergo long-range magnetic ordering below TN1 = 118 K, initially adopting a magnetic structure with a propagation vector (1/2 - δ, 0, 1/2) (0 ≤ δ ≤ 0.1) which is incommensurate with the nuclear structure and described in the Pbam1 '( a01/2)000 s magnetic superspace group, until at 92 K ( TINC) there is a first order lock-in transition to a structure in which these Fe2 moments form a magnetic structure with a propagation vector (1/2, 0, 1/2) which may be modeled using a 2 a × b × 2 c expansion of the nuclear cell in space group 36.178 B a b21 m (BNS notation). Below TN2 = 52 K the remaining third of the Fe2+ moments (Fe1 site) which are in a compressed trans-[FeSe4O2] octahedral environment undergo long-range ordering, as is evident from the magnetometry, the Mössbauer spectra, and the appearance of new magnetic Bragg peaks in the neutron diffractograms. The ordering of the second set of moments on the Fe1 sites results in a slight reorientation of the majority moments on the Fe2 sites. The magnetic structure at 1.5 K is described by a 2 a × 2 b × 2 c expansion of the nuclear cell in space group 9.40 I a b (BNS notation).

Doped Sr2FeIrO6-Phase Separation and a Jeff ≠ 0 State for Ir5.

High-resolution synchrotron X-ray and neutron powder diffraction data demonstrate that, in contrast to recent reports, Sr2FeIrO6 adopts an I1̅ symmetry double perovskite structure with an a-b-c- tilting distortion. This distorted structure does not tolerate cation substitution, with low levels of A-site (Ca, Ba, La) or Fe-site (Ga) substitution leading to separation into two phases: a stoichiometric I1̅ phase and a cation-substituted, P21/ n symmetry, a-a-c+ distorted double perovskite phase. Magnetization, neutron diffraction, and 57Fe Mössbauer data show that, in common with Sr2FeIrO6, the cation substituted Sr2- xA xFe1- yGa yIrO6 phases undergo transitions to type-II antiferromagnetically ordered states at TN ∼ 120 K. However, in contrast to stoichiometric Sr2FeIrO6, cation substituted samples exhibit a further magnetic transition at TA ∼ 220 K, which corresponds to the ordering of Jeff ≠ 0 Ir5+ centers in the cation-substituted, P21/ n symmetry, double perovskite phases.

Safety and tolerability of the first-in-class agent CPI-613 in combination with modified FOLFIRINOX in patients with metastatic pancreatic cancer: a single-centre, open-label, dose-escalation, phase 1 trial.

BACKGROUND: Pancreatic cancer statistics are dismal, with a 5-year survival of less than 10%, and more than 50% of patients presenting with metastatic disease. Metabolic reprogramming is an emerging hallmark of pancreatic adenocarcinoma. CPI-613 is a novel anticancer agent that selectively targets the altered form of mitochondrial energy metabolism in tumour cells, causing changes in mitochondrial enzyme activities and redox status that lead to apoptosis, necrosis, and autophagy of tumour cells. We aimed to establish the maximum tolerated dose of CPI-613 when used in combination with modified FOLFIRINOX chemotherapy (comprising oxaliplatin, leucovorin, irinotecan, and fluorouracil) in patients with metastatic pancreatic cancer. METHODS: In this single-centre, open-label, dose-escalation phase 1 trial, we recruited adult patients (aged ≥18 years) with newly diagnosed metastatic pancreatic adenocarcinoma from the Comprehensive Cancer Center of Wake Forest Baptist Medical Center (Winston-Salem, NC, USA). Patients had good bone marrow, liver and kidney function, and good performance status (Eastern Cooperative Oncology Group [ECOG] performance status 0-1). We studied CPI-613 in combination with modified FOLFIRINOX (oxaliplatin at 65 mg/m2, leucovorin at 400 mg/m2, irinotecan at 140 mg/m2, and fluorouracil 400 mg/m2 bolus followed by 2400 mg/m2 over 46 h). We applied a two-stage dose-escalation scheme (single patient and traditional 3+3 design). In the single-patient stage, one patient was accrued per dose level. The starting dose of CPI-613 was 500 mg/m2 per day; the dose level was then escalated by doubling the previous dose if there were no adverse events worse than grade 2 within 4 weeks attributed as probably or definitely related to CPI-613. The traditional 3+3 dose-escalation stage was triggered if toxic effects attributed as probably or definitely related to CPI-613 were grade 2 or worse. The dose level for CPI-613 for the first cohort in the traditional dose-escalation stage was the same as that used in the last cohort of the single-patient dose-escalation stage. The primary objective was to establish the maximum tolerated dose of CPI-613 (as assessed by dose-limiting toxicities). This trial is registered with ClinicalTrials.gov, number NCT01835041, and is closed to recruitment. FINDINGS: Between April 22, 2013, and Jan 8, 2016, we enrolled 20 patients. The maximum tolerated dose of CPI-613 was 500 mg/m2. The median number of treatment cycles given at the maximum tolerated dose was 11 (IQR 4-19). Median follow-up of the 18 patients treated at the maximum tolerated dose was 378 days (IQR 250-602). Two patients enrolled at a higher dose of 1000 mg/m2, and both had a dose-limiting toxicity. Two unexpected serious adverse events occurred, both for the first patient enrolled. Expected serious adverse events were: thrombocytopenia, anaemia, and lymphopenia (all for patient number 2; anaemia and lymphopenia were dose-limiting toxicities); hyperglycaemia (in patient number 7); hypokalaemia, hypoalbuminaemia, and sepsis (patient number 11); and neutropenia (patient number 20). No deaths due to adverse events were reported. For the 18 patients given the maximum tolerated dose, the most common grade 3-4 non-haematological adverse events were hyperglycaemia (ten [55%] patients), hypokalaemia (six [33%]), peripheral sensory neuropathy (five [28%]), diarrhoea (five [28%]), and abdominal pain (four [22%]). The most common grade 3-4 haematological adverse events were neutropenia (five [28%] of 18 patients), lymphopenia (five [28%]), anaemia (four [22%], and thrombocytopenia in three [17%]). Sensory neuropathy (all grade 1-3) was recorded in 17 (94%) of the 18 patients and was managed with dose de-escalation or discontinuation per standard of care. No patients died while on active treatment; 11 study participants died, with cause of death as terminal pancreatic cancer. Of the 18 patients given the maximum tolerated dose, 11 (61%) achieved an objective (complete or partial) response. INTERPRETATION: A maximum tolerated dose of CPI-613 was established at 500 mg/m2 when used in combination with modified FOLFIRINOX in patients with metastatic pancreatic cancer. The findings of clinical activity will require validation in a phase 2 trial. FUNDING: Comprehensive Cancer Center of Wake Forest Baptist Medical Center.

Metabolic PET Imaging in Oncology.

OBJECTIVE: In this article, we provide a general overview of how cancer cells subvert critical metabolic pathways to support their growth and unchecked division. Furthermore, we outline how molecular imaging can diagnostically exploit the resulting differences between cancer and normal cells. CONCLUSION: Molecular PET can provide valuable information about the metabolic dysregulation in cancer.

Soft chemical control of superconductivity in lithium iron selenide hydroxides Li(1-x)Fe(x)(OH)Fe(1-y)Se.

Hydrothermal synthesis is described of layered lithium iron selenide hydroxides Li(1-x)Fe(x)(OH)Fe(1-y)Se (x ∼ 0.2; 0.02 < y < 0.15) with a wide range of iron site vacancy concentrations in the iron selenide layers. This iron vacancy concentration is revealed as the only significant compositional variable and as the key parameter controlling the crystal structure and the electronic properties. Single crystal X-ray diffraction, neutron powder diffraction, and X-ray absorption spectroscopy measurements are used to demonstrate that superconductivity at temperatures as high as 40 K is observed in the hydrothermally synthesized samples when the iron vacancy concentration is low (y < 0.05) and when the iron oxidation state is reduced slightly below +2, while samples with a higher vacancy concentration and a correspondingly higher iron oxidation state are not superconducting. The importance of combining a low iron oxidation state with a low vacancy concentration in the iron selenide layers is emphasized by the demonstration that reductive postsynthetic lithiation of the samples turns on superconductivity with critical temperatures exceeding 40 K by displacing iron atoms from the Li(1-x)Fe(x)(OH) reservoir layer to fill vacancies in the selenide layer.

Benchtop Zone Refinement of Simulated Future Spent Nuclear Fuel Pyroprocessing Waste.

The UK's adoption of pyroprocessing of spent nuclear fuel as an alternative to the current aqueous processing routes requires a robust scientific underpinning of all relevant processes. One key process is the clean-up of the contaminated salt from the electroreducing and electrorefining processes. A proposed method for this clean-up is zone refining, whereby the tendency of the contaminants to remain in the liquid phase during melting and freezing is exploited to 'sweep' the contaminants to one end of the sample. Experiments were performed, utilising off-the-shelf laboratory equipment, to demonstrate the feasibility of zone refining for clean-up of electroreducing and electrorefining wastes. This was successful for the electrorefining simulant samples, with effective segregation coefficient, keff, values, which provide a measure of the degree of separation in the sample, between 0 and 1. Lower values indicate greater separation, with values of as low as 0.542 achieved here, corresponding to a reduction in RECl3 content from 10.0 wt.% to 8.4 wt.% (for 80% salt reuse). Due to difficulties in obtaining a fully homogeneous electroreducing simulant waste, it was not possible to demonstrate the feasibility of zone refining using the current experimental setup. Further research is required to elucidate the correct preparation conditions for production of homogeneous electroreducing waste simulants.

Topochemical fluorination of Sr3(M(0.5)Ru(0.5))2O7 (M = Ti, Mn, Fe), n = 2, Ruddlesden-Popper phases.

Reaction of the appropriate Sr3(M(0.5)Ru(0.5))2O7 (M = Ti, Mn, Fe), n = 2, Ruddlesden-Popper oxide with CuF2 under flowing oxygen results in formation of the oxide-fluoride phases Sr3(Ti(0.5)Ru(0.5))2O7F2, Sr3(Mn(0.5)Ru(0.5))2O7F2, and Sr3(Fe(0.5)Ru(0.5))2O(5.5)F(3.5) via a topochemical anion insertion/substitution process. Analysis indicates the titanium and manganese phases have Ti(4+), Ru(6+) and Mn(4+), Ru(6+) oxidation state combinations, respectively, while Mössbauer spectra indicate an Fe(3+), Ru(5.5+) combination for the iron phase. Thus, it can be seen that the soft fluorination conditions employed lead to formation of highly oxidized Ru(6+) centers in all three oxide-fluoride phases, while oxidation states of the other transition metal M cations remain unchanged. Fluorination of Sr3(Ti(0.5)Ru(0.5))2O7 to Sr3(Ti(0.5)Ru(0.5))2O7F2 leads to suppression of magnetic order as the fluorinated material approaches metallic behavior. In contrast, fluorination of Sr3(Mn(0.5)Ru(0.5))2O7 and Sr3(Fe(0.5)Ru(0.5))2O7 lifts the magnetic frustration present in the oxide phases, resulting in observation of long-range antiferromagnetic order at low temperature in Sr3(Mn(0.5)Ru(0.5))2O7F2 and Sr3(Fe(0.5)Ru(0.5))2O(5.5)F(3.5). The influence of the topochemical fluorination on the magnetic behavior of the Sr3(M(0.5)Ru(0.5))2O(x)F(y) phases is discussed on the basis of changes to the ruthenium oxidation state and structural distortions.

Topochemical reduction of the Ruddlesden-Popper phases Sr2Fe(0.5)Ru(0.5)O4 and Sr3(Fe(0.5)Ru(0.5))2O7.

Reaction of the Ruddlesden-Popper phases Sr2Fe(0.5)Ru(0.5)O4 and Sr3(Fe(0.5)Ru(0.5))2O7 with CaH2 results in the topochemical deintercalation of oxide ions from these materials and the formation of samples with average compositions of Sr2Fe(0.5)Ru(0.5)O(3.35) and Sr3(Fe(0.5)Ru(0.5))2O(5.68), respectively. Diffraction data reveal that both the n = 1 and n = 2 samples consist of two-phase mixtures of reduced phases with subtly different oxygen contents. The separation of samples into two phases upon reduction is discussed on the basis of a short-range inhomogeneous distribution of iron and ruthenium in the starting materials. X-ray absorption data and Mössbauer spectra reveal the reduced samples contain an Fe(3+) and Ru(2+/3+) oxidation state combination, which is unexpected considering the Fe(3+)/Fe(2+) and Ru(3+)/Ru(2+) redox potentials, suggesting that the local coordination geometry of the transition metal sites helps to stabilize the Ru(2+) centers. Fitted Mössbauer spectra of both the n = 1 and n = 2 samples are consistent with the presence of Fe(3+) cations in square planar coordination sites. Magnetization data of both materials are consistent with spin glass-like behavior.

Theory testing in prehistoric North America: fruits of one of the world's great archeological natural laboratories.

This paper has several interconnected goals. First and most generally, we will review the project represented by the papers in this dedicated issue and the SAA Symposium (2012) on Social Complexity and the Bow. This project centers on the ever-stronger and broader theory testing now becoming feasible in archeology and anthropology, in this case exploiting the unique natural laboratory represented by what we refer to as the North American Neolithic transitions. Second, we will strive to synopsize the papers in this issue as opportunities to falsify two general theories of the cause of increases in social complexity associated with the North American Neolithic: warfare and social coercion theories.(1) We argue that, though much work remains to be done, the current evidence supports one of the central predictions of both these theories, that the local arrival of elite bow technology was a central driver of local transitions to increased social complexity. This conclusion, if ultimately verified, has profound implications for the possibility of general theories of history. Third, we will argue that several important details of this evidence falsify warfare theory and support (fail to falsify) social coercion theory (the authors' favored perspective). Moreover, several potential falsifications of social coercion theory are amenable to alternative interpretations, leading to new falsifiable predictions. Finally, we discuss how interactions with our colleagues in this project produced new insights into several details of the predictions of social coercion theory, improving our interpretative capacity.

Introduction: social complexity and the bow in the prehistoric North American record.

This Special Issue of Evolutionary Anthropology grew out of a symposium at the 2012 Society for American Archaeology (SAA) meeting in Memphis, Tennessee (April 18-22). The goal of the symposium was to explore what we will argue is one of the most important and promising opportunities in the global archeological enterprise. In late prehistoric North America, the initial rise of cultures of strikingly enhanced complexity and the local introduction of a novel weapon technology, the bow, apparently correlate intimately in a diverse set of independent cases across the continent, as originally pointed out by Blitz. If this empirical relationship ultimately proves robust, it gives us an unprecedented opportunity to evaluate hypotheses for the causal processes producing social complexity and, by extension, to assess the possibility of a universal theory of history. The rise of comparably complex cultures was much more recent in North America than it was elsewhere and the resulting fresher archeological record is relatively well explored. These and other features make prehistoric North America a unique empirical environment. Together, the symposium and this issue have brought together outstanding investigators with both empirical and theoretical expertise. The strong cross-feeding and extended interactions between these investigators have given us all the opportunity to advance the promising exploration of what we call the North American Neolithic transitions. Our goal in this paper is to contextualize this issue.

Antimicrobial Fe2O3-CuO-P2O5 glasses.

Glasses with high antimicrobial efficacy were developed in the Fe2O3-CuO-P2O5 ternary system to mitigate fomite-mediated transmission of infectious diseases in high-risk settings such as hospitals, daycares, and nursing homes. Binary CuO-P2O5 glasses were not durable enough for use as high touch point articles, so Fe2O3 was added to the compositions to increase the chemical durability. The amount of Cu leachate decreased by at least 3 orders of magnitude when Fe2O3 was increased from 0 to 13.1 mol%. At the highest Fe2O3 contents and corresponding highest durability, the glass was no longer able to pass a test of antimicrobial efficacy with < 3 log kill compared to > 5 log kill for all other compositions. Ab-initio molecular dynamics simulations showed increasing bridging oxygen species at the expense of non-bridging oxygen species with the increase in Fe2O3 content, showing that the glasses exhibited increased chemical durability because they were more interconnected and structurally bound. Experimental results with glasses at fixed CuO and decreasing Fe2O3 confirmed that Fe2O3 content (not CuO) controlled the Cu release rate and, thus, the antimicrobial efficacy of the glasses. The significance of the oxidation state of the leached Cu was overwhelmed by the importance of the amount of Cu leachate.

Synthesis and characterization of Li11Nd18Fe4O(39-δ).

Li(11)Nd(18)Fe(4)O(39-δ) has been synthesized by the solid-state reaction of pellets, covered with powder of the same composition to avoid lithium loss, with a final reaction temperature of 950 °C. This phase has been reported previously to have various stoichiometries: Li(5)Nd(4)FeO(10), Li(8)Nd(18)Fe(5)O(39), and Li(1.746)Nd(4.494)FeO(9.493). The crystal structure of Li(11)Nd(18)Fe(4)O(39-δ) is closely related to that reported previously for two of the other three compositions but contains extra Li and differences in Li/Fe site occupancies. Fe is present in a mixture of 3+ and 4+ oxidation states, as confirmed by Mössbauer spectroscopy. The oxygen content of 39 - δ is variable, depending on the processing conditions. Samples slow-cooled in air from 800 °C are semiconducting, attributed to the presence of Fe(4+) ions, whereas samples quenched from 950 °C in N(2) are insulating.

Evidence for a novel, effective approach to targeting carcinoma catabolism exploiting the first-in-class, anti-cancer mitochondrial drug, CPI-613.

Clinical targeting of the altered metabolism of tumor cells has long been considered an attractive hypothetical approach. However, this strategy has yet to perform well clinically. Metabolic redundancy is among the limitations on effectiveness of many approaches, engendering intrinsic single-agent resistance or efficient evolution of such resistance. We describe new studies of the multi-target, tumor-preferential inhibition of the mitochondrial tricarboxylic acid (TCA) cycle by the first-in-class drug CPI-613® (devimistat). By suppressing the TCA hub, indispensable to many metabolic pathways, CPI-613 substantially reduces the effective redundancy of tumor catabolism. This TCA cycle suppression also engenders an apparently homeostatic accelerated, inefficient consumption of nutrient stores in carcinoma cells, eroding some sources of drug resistance. Nonetheless, sufficiently abundant, cell line-specific lipid stores in carcinoma cells are among remaining sources of CPI-613 resistance in vitro and during the in vivo pharmacological drug pulse. Specifically, the fatty acid beta-oxidation step delivers electrons directly to the mitochondrial electron transport system (ETC), by-passing the TCA cycle CPI-613 target and producing drug resistance. Strikingly, tested carcinoma cell lines configure much of this fatty acid flow to initially traverse the peroxisome enroute to additional mitochondrial beta-oxidation. This feature facilitates targeting as clinically practical agents disrupting this flow are available. Two such agents significantly sensitize an otherwise fully CPI-613-resistant carcinoma xenograft in vivo. These and related results are strong empirical support for a potentially general class of strategies for enhanced clinical targeting of carcinoma catabolism.

Effects of iron substitution and anti-site disorder on crystal structures, vibrational, optical and magnetic properties of double perovskites Sr2(Fe1-xNix)TeO6.

The double-perovskite series, Sr2(Fe1-xNix)TeO6 (x = 0, 0.25, 0.50, 0.75, and 1) has been synthesized in polycrystalline form by solid-state reaction at 1300 K in air. Their crystal structures were probed by powder X-ray diffraction at room temperature. Rietveld analysis revealed that all samples crystallize in the monoclinic space group I2/m. The double-perovskite structures ideally contain two alternating types of octahedra (Fe/Ni)2dO6 and (Te)2aO6, tilted in the system (a-a-c0). However, the refinements have shown a complex distribution of all three cations over the two available octahedral sites; 2d (½, ½, 0) and 2a (0, 0, 0). Raman spectroscopy further complements the obtained results, by revealing a tiny increase of the wavenumber of some Raman modes when Fe is substituted by Ni. The optical characteristics of the series were determined by fitting diffuse reflectance UV/Vis spectra enabling the optical band gaps to be derived from Tauc method and derivation of absorption spectra fitting (DASF) techniques. Analyses of the obtained 57Fe Mössbauer hyperfine parameters at room temperature of samples with compositions x = 0, 0.25, 0.50 and 0.75 reveal the presence of Fe3+ in high-spin state with an anti-site disorder of Fe-Ni-Te cations in distorted octahedral environments (site 2d and 2a). The results show that significant correlations exist between the crystal structures and physical properties of double perovskites containing B site transition elements of different charge and size. Temperature-dependent magnetic susceptibility data show magnetic transitions below 40(1) K (38(1) K, 31(1) K, 25(1) K, 20(1) K, and 35(1) K for x = 0, 0.25, 0.50, 0.75, and 1, respectively. A divergence between FC and ZFC curves for all compositions has been observed. The results show that the ground states of the doped materials might be spin glasses or magnetically ordered.

Self-Assembly of Nanosheet-Supported Fe-MOF Heterocrystals as a Reusable Catalyst for Boosting Advanced Oxidation Performance via Radical and Nonradical Pathways.

Heterojunction catalysts have drawn increasing interest for the visible light-driven Fenton reaction and bring tremendous opportunities for environmental remediation. Herein, a BiOI/MIL-53(Fe) Z-scheme heterojunction (named BMFe) was synthesized for the first time via a facile strategy. Compared with pristine BiOI and MIL-53(Fe) catalysts, the two-dimensional/three-dimensional (2D/3D) heterojunction catalyst manifested remarkable catalytic performance toward degradation of phenol, bisphenol A, methylene blue, and carbamazepine, which is attributed mainly to the interfacial integration and efficient charge separation. By virtue of coupling at the interface, as confirmed by XPS, 57Fe Mössbauer spectroscopy, and DFT calculations, the BMFe catalyst promoted the transfer of electron-hole pairs via Z-scheme and improved the chemical activation of hydrogen peroxide. The subsequent holes, free radicals, and nonradicals can effectively and continuously decompose pollutants, achieving a positive synergistic effect between photocatalysis and Fenton reactions. Simultaneously, the specially designed BiOX(X = Br, Cl)/MIL-53(Fe) and BiOI/Fe-MOFs(MIL-101, MIL-88) heterojunctions also exhibited advanced oxidative capacity for organic pollutants. Given their practical value for industrial applications, BMFe beads (1.0 ± 0.15 mm) synthesized via a blend cross-linking method can significantly advance long-term stability and recyclability. The integration of Fe-based metal-organic frameworks with bismuth oxyhalide semiconductors provides a new perspective on developing heterojunction catalysts for environmental remediation.

BiOBr/MoS2 catalyst as heterogenous peroxymonosulfate activator toward organic pollutant removal: Energy band alignment and mechanism insight.

Utilization of heterogenous catalysts to trigger peroxymonosulfate (PMS) activation is considered an efficient strategy for environmental decontamination. Herein, a tightly bonded flake-like 2D/2D BiOBr/MoS2 heterojunction was successfully designed through co-precipitation process. By virtue of matched energy levels and intimate interfacial coupling, the Type-II BiOBr/MoS2 heterojunction significantly expedited charge carrier transfer and thereby promoted the catalytic performance for organic dye oxidation and Cr(VI) reduction. The specially designed BiOBr/MoS2 heterojunction is also conducive to split PMS and continuously generated highly active species (SO4-, OH and O2-) in a photo-Fenton system, achieving extraordinary catalytic capacity for various emerging organic pollutants (including phenol, bisphenol A and carbamazepine). The photoexcited electron with prolonged lifetime and exposed Mo sites with multivalence and multiphase nature can effectively activate PMS, which further promotes the oxidation efficiency of holes, as confirmed by scavenging experiments. The excellent stability and oxidative properties could justify scale up using BiOBr/MoS2 to a small pilot test, implementing the potential value in practical applications. This study would provide novel insight and cognition of PMS activation via a superior heterojunction for complex polluted wastewater treatment.