Establishing ZIF-8 as a reference material for hydrogen cryoadsorption: An interlaboratory study.

Hydrogen storage by cryoadsorption on porous materials has the advantages of low material cost, safety, fast kinetics, and high cyclic stability. The further development of this technology requires reliable data on the H2 uptake of the adsorbents, however, even for activated carbons the values between different laboratories show sometimes large discrepancies. So far no reference material for hydrogen cryoadsorption is available. The metal-organic framework ZIF-8 is an ideal material possessing high thermal, chemical, and mechanical stability that reduces degradation during handling and activation. Here, we distributed ZIF-8 pellets synthesized by extrusion to 9 laboratories equipped with 15 different experimental setups including gravimetric and volumetric analyzers. The gravimetric H2 uptake of the pellets was measured at 77 K and up to 100 bar showing a high reproducibility between the different laboratories, with a small relative standard deviation of 3-4 % between pressures of 10-100 bar. The effect of operating variables like the amount of sample or analysis temperature was evaluated, remarking the calibration of devices and other correction procedures as the most significant deviation sources. Overall, the reproducible hydrogen cryoadsorption measurements indicate the robustness of the ZIF-8 pellets, which we want to propose as a reference material.

Are the Accompanying Cations of Doping Anions Influential in Conducting Organic Polymers? The Case of the Popular PEDOT.

Conducting organic polymers (COPs) are made of a conjugated polymer backbone supporting a certain degree of oxidation. These positive charges are compensated by the doping anions that are introduced into the polymer synthesis along with their accompanying cations. In this work, the influence of these cations on the stoichiometry and physicochemical properties of the resulting COPs have been investigated, something that has previously been overlooked, but, as here proven, is highly relevant. As the doping anion, metallacarborane [Co(C2 B9 H11 )2 ]- was chosen, which acts as a thistle. This anion binds to the accompanying cation with a distinct strength. If the binding strength is weak, the doping anion is more prone to compensate the positive charge of the polymer, and the opposite is also true. Thus, the ability of the doping anion to compensate the positive charges of the polymer can be tuned, and this determines the stoichiometry of the polymer. As the polymer, PEDOT was studied, whereas Cs+ , Na+ , K+ , Li+ , and H+ as cations. Notably, with the [Co(C2 B9 H11 )2 ]- anions, these cations are grouped into two sets, Cs+ and H+ in one and Na+ , K+ , and Li+ in the second, according to the stoichiometry of the COPs: 2:1 EDOT/[Co(C2 B9 H11 )2 ]- for Cs+ and H+ , and 3:1 EDOT/[Co(C2 B9 H11 )2 ]- for Na+ , K+ , and Li+ . The distinct stoichiometries are manifested in the physicochemical properties of the COPs, namely in the electrochemical response, electronic conductivity, ionic conductivity, and capacitance.

Hydrogen Storage in Porous Materials: Status, Milestones, and Challenges.

In this account the most relevant advancements in hydrogen storage in porous materials are presented. These include the current state-of-the-art, the challenges which have been overcome, and the hurdles which still remain. The most important milestones which will be discussed in this work will be the development of new apparatuses capable of delivering reliable results under a broad range of operational conditions, in which analysis temperature and pressure are critical parameters. Other aspects such as the materials storage capacity in gravimetric and volumetric terms will be critically discussed to identify the conditions required from an ideal material. Finally, different upgrade possibilities from modifying the adsorbate-adsorbent interaction to using rigid or flexible materials will be presented and put into perspective with current literature.

Relevance of the Interaction between the M-Phthalocyanines and Carbon Nanotubes in the Electroactivity toward ORR.

In this work, the influence of the interaction between the iron and cobalt-phthalocyanines (FePc and CoPc) and carbon nanotubes (CNTs) used as support in the electroactivity toward oxygen reduction reaction (ORR) in alkaline media has been investigated. A series of thermal treatments were performed on these materials in order to modify the interaction between the CNTs and the phthalocyanines. The FePc-based catalysts showed the highest activity, with comparable performance to the state-of-the-art Pt-Vulcan catalyst. A heat treatment at 400 °C improved the activity of FePc-based catalysts, while the use of higher temperatures or oxidative atmosphere rendered the decomposition of the macrocyclic compound and consequently the loss of the electrochemical activity of the complex. CoPc-based catalysts performance was negatively affected for all of the tested treatments. Thermogravimetric analyses demonstrated that the FePc was stabilized when loaded onto CNTs, while CoPc did not show such a feature, pointing to a better interaction of the FePc instead of the CoPc. Interestingly, electrochemical measurements demonstrated an improvement of the electron transfer rate in thermally treated FePc-based catalysts. They also allowed us to assess that only 15% of the iron in the catalyst was available for direct electron transfer. This is the same iron amount that remains on the catalyst after a strong acid washing with concentrated HCl (ca. 0.3 wt %), which is enough to deliver a comparable ORR activity. Durability tests confirmed that the catalysts deactivation occurs at a slower rate in those catalysts where FePc is strongly attached to the CNT surface. Thus, the highest ORR activity seems to be provided by those FePc molecules that are strongly attached to the CNT surface, pointing out the relevance of the interaction between the support and the FePc in these catalysts.

Synthesis of TiO2 with Hierarchical Porosity for the Photooxidation of Propene.

The elimination of volatile organic compounds (VOCs) at low concentration is a subject of great interest because these compounds are very harmful for the environment and human health. In this work, we have developed a synthesis methodology of TiO2 that allows obtaining meso-macroporous materials with hierarchical porosity and with high thermal stability for their application as photocatalysts in the removal of VOCs, specifically propene. The materials synthesized in this work were characterized by Scanning electron microscope (SEM), Transmission electron microscopy (TEM), powder X-ray diffraction (XRD), Thermogravimetric Analysis (TG), and nitrogen adsorption. It is observed that the samples calcined at 250 °C and 500 °C present a high photoactivity for the photooxidation of propene, which is similar to the benchmark material P25 (commercial TiO2). Moreover, the textural properties are better than those for P25, indicating that the samples are interesting for the preparation of photocatalysts with different conformations, such as in the form of coatings and fillings in different size scales.

Evolution of the PVP-Pd Surface Interaction in Nanoparticles through the Case Study of Formic Acid Decomposition.

Palladium nanoparticles (Pd NPs) were synthesized by the reduction-by-solvent method using polyvinylpirrolidone (PVP) as capping agent. The nonstatic interaction between PVP and the metallic surface may change the properties of the NPs due to the different possible interactions, through either the O or N atoms of the PVP. In order to analyze these effects and their repercussions in their catalytic performance, Pd NPs with various PVP/Pd molar ratios (1, 10, and 20) were prepared, deposited on silica, and tested in the formic acid decomposition reaction. The catalytic tests were conducted using catalysts prepared by loading NPs with three different time lapses between their purification and their deposition on the silica support (1 day, 1 month, and 6 months). CO adsorption, FTIR spectroscopy, XPS, and TEM characterization were used to determine the accessibility of the Pd NPs surface sites, the electronic state of Pd, and the average NPs size, respectively. The H2 production from the formic acid decomposition reaction has a strong dependence on the Pd surface features, which in turn are related to the NPs aging time due to the progressive removal of the PVP.

Eco-Friendly Mechanochemical Synthesis of Bifunctional Metal Oxide Electrocatalysts for Zn-Air Batteries.

The development of green and environmentally friendly synthesis methods of electrocatalysts is a crucial aspect in decarbonizing energy generation. In this study, eco-friendly mechanochemical synthesis of perovskite metal oxide-carbon black composites is proposed using different conditions and additives such as KOH. Furthermore, the optimization of ball milling conditions, including time and rotational speed, is studied. The mechanochemical synthesis in solid-state conditions without additives produces electrocatalysts that exhibit the highest bifunctional electrochemical activity towards both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Moreover, this synthesis demonstrates a lower Environmental Impact Factor (E-factor), indicating its greener nature, and due to its simplicity, it has a great potential for scalability. The obtained bifunctional electrocatalysts have been tested in a rechargeable zinc-air battery (ZAB) for 22 h with similar performance compared to the commercial catalyst (Pt/C) at significantly lower cost. These promising findings are attributed to the enhanced interaction between the perovskite metal oxide and carbon material and the improved dispersion of the perovskite metal oxide on the carbon materials.

Enhancing Interaction between Lanthanum Manganese Cobalt Oxide and Carbon Black through Different Approaches for Primary Zn-Air Batteries.

Due to the need for decarbonization in energy generation, it is necessary to develop electrocatalysts for the oxygen reduction reaction (ORR), a key process in energy generation systems such as fuel cells and metal-air batteries. Perovskite-carbon material composites have emerged as active and stable electrocatalysts for the ORR, and the interaction between both components is a crucial aspect for electrocatalytic activity. This work explores different mixing methods for composite preparation, including mortar mixing, ball milling, and hydrothermal and thermal treatments. Hydrothermal treatment combined with ball milling resulted in the most favorable electrocatalytic performance, promoting intimate and extensive contact between the perovskite and carbon material and improving electrocatalytic activity. Employing X-ray photoelectron spectroscopy (XPS), an increase in the number of M-O-C species was observed, indicating enhanced interaction between the perovskite and the carbon material due to the adopted mixing methods. This finding was further corroborated by temperature-programmed reduction (TPR) and temperature-programmed desorption (TPD) techniques. Interestingly, the ball milling method results in similar performance to the hydrothermal method in the zinc-air battery and, thus, is preferable because of the ease and straightforward scalability of the preparation process.

Preparation of a ruthenium complex covalently bonded to multilayer graphene and its evaluation as a photocatalyst.

Multilayer graphene (MLG), obtained by mild sonication of graphite in NMP, was functionalised via 1,3-dipolar cycloaddition with azomethine ylides generated by thermal 1,2-prototropy from various imino esters. The microwave-assisted functionalisation took place in five hours at 100 °C. The resulting MLG, containing substituted proline-based amine functional groups, was characterized using XPS and showed a nitrogen loading three times that obtained for the same transformation performed for five days using convection-assisted heating. The preparation of the imino ester containing a bipyridine unit at the arylidene position allowed for the preparation of the corresponding functionalised MLG, which incorporated the ruthenium atom to achieve a heterogeneous MLG-Ru complex. This supported complex was tested, as a proof of concept, as a photocatalyst of the aerobic oxidative hydroxylation of 4-methoxyphenylboronic acid.

Removal of Mo(VI), Pb(II), and Cu(II) from wastewater using electrospun cellulose acetate/chitosan biopolymer fibers.

Environmentally friendly polymers such as cellulose acetate (CA) and chitosan (CS) were used to obtain electrospun fibers for Cu2+, Pb2+, and Mo6+ capture. The solvents dichloromethane (DCM) and dimethylformamide (DMF) allowed the development of a surface area of 148 m2 g-1 for CA fibers and 113 m2 g-1 for cellulose acetate/chitosan (CA/CS) fibers. The fibers were characterized by IR-DRIFT, SEM, TEM, CO2 sorption isotherms at 273 K, Hg porosimetry, TGA, stress-strain tests, and XPS. The CA/CS fibers had a higher adsorption capacity than CA fibers without affecting their physicochemical properties. The capture capacity reached 102 mg g-1 for Cu2+, 49.3 mg g-1 for Pb2+, and 13.1 mg g-1 for Mo6+. Furthermore, optimal pH, adsorption times qt, and C0 were studied for the evaluation of kinetic models and adsorption isotherms. Finally, a proposal for adsorbate-adsorbent interactions is presented as a possible capture mechanism where, in the case of Mo6+, a computational study is presented. The results demonstrate the potential to evaluate the fibers in tailings wastewater from copper mining.

Nanoarchitectures based on layered titanosilicates supported on glass fibers: application to hydrogen storage.

This work reports on the synthesis of nanosheets of layered titanosilicate JDF-L1 supported on commercial E-type glass fibers with the aim of developing novel nanoarchitectures useful as robust and easy to handle hydrogen adsorbents. The preparation of those materials is carried out by hydrothermal reaction from the corresponding gel precursor in the presence of the glass support. Because of the basic character of the synthesis media, silica from the silicate-based glass fibers can be involved in the reaction, cementing its associated titanosilicate and giving rise to strong linkages on the support with the result of very stable heterostructures. The nanoarchitectures built up by this approach promote the growth and disposition of the titanosilicate nanosheets as a house-of-cards radially distributed around the fiber axis. Such an open arrangement represents suitable geometry for potential uses in adsorption and catalytic applications where the active surface has to be available. The content of the titanosilicate crystalline phase in the system represents about 12 wt %, and this percentage of the adsorbent fraction can achieve, at 298 K and 20 MPa, 0.14 wt % hydrogen adsorption with respect to the total mass of the system. Following postsynthesis treatments, small amounts of Pd (<0.1 wt %) have been incorporated into the resulting nanoarchitectures in order to improve their hydrogen adsorption capacity. In this way, Pd-layered titanosilicate supported on glass fibers has been tested as a hydrogen adsorbent at diverse pressures and temperatures, giving rise to values around 0.46 wt % at 298 K and 20 MPa. A mechanism of hydrogen spillover involving the titanosilicate framework and the Pd nanoparticules has been proposed to explain the high increase in the hydrogen uptake capacity after the incorporation of Pd into the nanoarchitecture.

Clay-supported graphene materials: application to hydrogen storage.

The present work refers to clay-graphene nanomaterials prepared by a green way using caramel from sucrose and two types of natural clays (montmorillonite and sepiolite) as precursors, with the aim of evaluating their potential use in hydrogen storage. The impregnation of the clay substrates by caramel in aqueous media, followed by a thermal treatment in the absence of oxygen of these clay-caramel intermediates gives rise to graphene-like materials, which remain strongly bound to the silicate support. The nature of the resulting materials was characterized by different techniques such as XRD, Raman spectroscopy and TEM, as well as by adsorption isotherms of N2, CO2 and H2O. These carbon-clay nanocomposites can act as adsorbents for hydrogen storage, achieving, at 298 K and 20 MPa, over 0.1 wt% of hydrogen adsorption excess related to the total mass of the system, and a maximum value close to 0.4 wt% of hydrogen specifically related to the carbon mass. The very high isosteric heat for hydrogen sorption determined from adsorption isotherms at different temperatures (14.5 kJ mol(-1)) fits well with the theoretical values available for hydrogen storage on materials that show a strong stabilization of the H2 molecule upon adsorption.

Binderless thin films of zeolite-templated carbon electrodes useful for electrochemical microcapacitors with ultrahigh rate performance.

Controlled nanozeolite deposits are prepared by electrochemical techniques on a macroporous carbon support and binderless thin film electrodes of zeolite-templated carbon are synthesized using the deposits as templates. The obtained film electrodes exhibit extremely high area capacitance (10-12 mF cm(-2)) and ultrahigh rate capability in a thin film capacitor.

Sustainable Synthesis of Metal-Doped Lignin-Derived Electrospun Carbon Fibers for the Development of ORR Electrocatalysts.

The aim of this work is to establish the Oxygen Reduction Reaction (ORR) activity of self-standing electrospun carbon fiber catalysts obtained from different metallic salt/lignin solutions. Through a single-step electrospinning technique, freestanding carbon fiber (CF) electrodes embedded with various metal nanoparticles (Co, Fe, Pt, and Pd), with 8-16 wt% loadings, were prepared using organosolv lignin as the initial material. These fibers were formed from a solution of lignin and ethanol, into which the metallic salt precursors were introduced, without additives or the use of toxic reagents. The resulting non-woven cloths were thermostabilized in air and then carbonized at 900 °C. The presence of metals led to varying degrees of porosity development during carbonization, improving the accessibility of the electrolyte to active sites. The obtained Pt and Pd metal-loaded carbon fibers showed high nanoparticle dispersion. The performance of the electrocatalyst for the oxygen reduction reaction was assessed in alkaline and acidic electrolytes and compared to establish which metals were the most suitable for producing carbon fibers with the highest electrocatalytic activity. In accordance with their superior dispersion and balanced pore size distribution, the carbon fibers loaded with 8 wt% palladium showed the best ORR activity, with onset potentials of 0.97 and 0.95 V in alkaline and acid media, respectively. In addition, this electrocatalyst exhibits good stability and selectivity for the four-electron energy pathway while using lower metal loadings compared to commercial catalysts.

Electrochemical functionalization at anodic conditions of multi-walled carbon nanotubes with chlorodiphenylphosphine.

Covalent functionalization of multi-walled carbon nanotubes (MWCNTs) and oxidized MWCNTs (o-MWCNTs) with chlorodiphenylphosphine (Ph2PCl) has been studied by cyclic voltammetry in organic medium. Depending the upper potential limit used in the electrochemical functionalization, different amount of phosphorus incorporation n is obtained, as result of the formation of radical species during the electrochemical oxidation of the Ph2PCl. The electrochemical oxidation of Ph2PCl promotes the covalent attachment of diphenylphosphine-like structure on the carbon nanotube surface. At the same time, the incorporation of Cl on the carbon nanotubes is observed during the functionalization. Furthermore, the presence of oxygen surface groups on the MWCNTs provides a favorable attachment of the Ph2P∙+ species, which has promoted preferentially the formation of CP bonds, whereas the amount of Cl is reduced.

Pyrroloquinoline quinone-dependent glucose dehydrogenase bioelectrodes based on one-step electrochemical entrapment over single-wall carbon nanotubes.

Development of effective direct electron transfer is considered an interesting platform to obtain high performance bioelectrodes. Therefore, designing of scalable and cost-effective immobilization routes that promotes correct direct electrical contacting between the electrode material and the redox enzyme is still required. As we present here, electrochemical entrapment of pyrroloquinoline quinone-dependent glucose dehydrogenase (PQQ-GDH) on single-wall carbon nanotube (SWCNT)-modified electrodes was carried out in a single step during electrooxidation of para-aminophenyl phosphonic acid (4-APPA) to obtain active bioelectrodes. The adequate interaction between SWCNTs and the enzyme can be achieved by making use of phosphorus groups introduced during the electrochemical co-deposition of films, improving the electrocatalytic activity towards glucose oxidation. Two different procedures were investigated for electrode fabrication, namely the entrapment of reconstituted holoenzyme (PQQ-GDH) and the entrapment of apoenzyme (apo-GDH) followed by subsequent in situ reconstitution with the redox cofactor PQQ. In both cases, PQQ-GDH preserves its electrocatalytic activity towards glucose oxidation. Moreover, in comparison with a conventional drop-casting method, an important enhancement in sensitivity was obtained for glucose oxidation (981.7 ± 3.5 nA mM-1) using substantially lower amounts of enzyme and cofactor (PQQ). The single step electrochemical entrapment in presence of 4-APPA provides a simple method for the fabrication of enzymatic bioelectrodes.

H2 Production from Formic Acid Using Highly Stable Carbon-Supported Pd-Based Catalysts Derived from Soft-Biomass Residues: Effect of Heat Treatment and Functionalization of the Carbon Support.

The production of hydrogen from liquid organic hydrogen carrier molecules stands up as a promising option over the conventional hydrogen storage methods. In this study, we explore the potential of formic acid as a convenient hydrogen carrier. For that, soft-biomass-derived carbon-supported Pd catalysts were synthesized by a H3PO4-assisted hydrothermal carbonization method. To assess the impact of the properties of the support in the catalytic performance towards the dehydrogenation of formic acid, three different strategies were employed: (i) incorporation of nitrogen functional groups; (ii) modification of the surface chemistry by performing a thermal treatment at high temperatures (i.e., 900 °C); and (iii) combination on both thermal treatment and nitrogen functionalization. It was observed that the modification of the carbon support with these strategies resulted in catalysts with enhanced performance and outstanding stability even after six consecutive reaction cycles, thus highlighting the important effect of tailoring the properties of the support.

Polyaniline-Derived N-Doped Ordered Mesoporous Carbon Thin Films: Efficient Catalysts towards Oxygen Reduction Reaction.

One of the most challenging targets in oxygen reduction reaction (ORR) electrocatalysts based on N-doped carbon materials is the control of the pore structure and obtaining nanostructured thin films that can easily be incorporated on the current collector. The carbonization of nitrogen-containing polymers and the heat treatment of a mixture of carbon materials and nitrogen precursor are the most common methods for obtaining N-doped carbon materials. However, in this synthetic protocols, the surface area and pore distribution are not controlled. This work enables the preparation of 2D-ordered N-doped carbon materials through the carbonization of 2D polyaniline. For that purpose, aniline has been electropolymerized within the porous structure of two different templates (ordered mesoporous Silica and ordered mesoporous Titania thin films). Thus, aniline has been impregnated into the porous structure and subsequently electropolymerized by means of chronoamperometry at constant potential. The resultant samples were heat-treated at 900 °C with the aim of obtaining 2D N-doped carbon materials within the template structures. Polyaniline and polyaniline-derived carbon materials have been analyzed via XPS and TEM and characterized by electrochemical measurements. It is worth noting that the obtained 2D-ordered mesoporous N-doped carbon materials have proved to be highly active electrocatalysts for the ORR because of the formation of quaternary nitrogen species during the heat treatment.

Tailoring Intrinsic Properties of Polyaniline by Functionalization with Phosphonic Groups.

Phosphonated polyanilines were synthesized by copolymerization of aniline (ANI) with both 2- and 4-aminophenylphosphonic acids (APPA). The material composition and the final properties of the copolymers can be easily tailored by controlling the monomers ANI/APPA molar feed ratio. An important influence on the reactivity of monomers has been found with the substituent position in the ring, leading to differences in the properties and size of blocks of each monomer in the polymer. As expected, while 2APPA shows more similarities to ANI, 4APPA is much less reactive. Phosphorus loading of ~5 at% was achieved in the poly(aniline-co-2-aminophenylphosphonic acid) (PANI2APPA) with a 50/50 molar feed ratio. All the resulting copolymers were characterized by different techniques. Experimental results and density functional theory (DFT) computational calculations suggest that the presence of phosphonic groups in the polymeric chain gives rise to inter- and intra-chain interactions, as well as important steric effects, which induce a slight twist in the substituted PANI structure. Therefore, the physicochemical, electrical, and electrochemical properties are modified and can be suitably controlled.

Zn-Promoted Selective Gas-Phase Hydrogenation of Tertiary and Secondary C4 Alkynols over Supported Pd.

We have investigated the gas-phase (P = 1 atm; T = 373 K) hydrogenation of (tertiary alkynol) 2-methyl-3-butyn-2-ol (MBY) and (secondary) 3-butyn-2-ol (BY) over a series of carbon (C), non-reducible (Al2O3 and MgO), and reducible (CeO2 and ZnO) supported monometallic [Pd (0.6-1.2% wt) and Zn (1% wt)] and bimetallic Pd-Zn (Pd:Zn mol ratio = 95:5, 70:30, and 30:70) catalysts synthesized by deposition-precipitation and colloidal deposition. The catalysts have been characterized by H2 chemisorption, hydrogen temperature-programmed desorption (H2-TPD), specific surface area (SSA), X-ray photoelectron spectroscopy (XPS), and transmission (TEM) and scanning transmission electron microscopy (STEM) analyses. Reaction over these catalysts generated the target alkenol [2-methyl-3-buten-2-ol (MBE) and 3-buten-2-ol (BE)] through partial hydrogenation and alkanol [2-methyl-butan-2-ol (MBA) and 2-butanol (BA)]/ketone [2-butanone (BONE)] as a result of full hydrogenation and double-bond migration. The catalysts exhibit a similar Pd nanoparticle size (2.7 ± 0.3 nm) but a modified electronic character (based on XPS). Hydrogenation activity is linked to surface hydrogen (from H2 chemisorption and H2-TPD). An increase in H2:alkynol (from 1 → 10) results in enhanced alkynol consumption with a greater rate in the transformation of MBY (vs BY); H2:alkynol had negligible effect on product distribution. Reaction selectivity is insensitive to the Pd site electron density with a similar response (SMBE = 65 ± 9% and SBE = 70 ± 8%) over Pdδ- (on Al2O3 and MgO) and Pdδ+ (on C and CeO2). A Pd/ZnO catalyst delivered enhanced alkenol selectivity (SMBE = 90% and SBE = 96%) attributed to PdZn alloy phase formation (proved by XRD and XPS) but low activity, ascribed to metal encapsulation. A two-fold increase in the consumption rate was recorded for Pd-Zn/Al2O3 (30:70) versus Pd/ZnO with a similar alloy content (32 ± 4% from XPS), ascribed to a contribution due to spillover hydrogen (from H2-TPD) where high alkenol selectivity was maintained.