Synthesis and Characterization of Alkoxysilane-Bearing Photoreversible Cinnamic Side Groups: A Promising Building-Block for the Design of Multifunctional Silica Nanoparticles.

The present study reports on the synthesis of a new alkoxysilane-bearing light-responsive cinnamyl group and its application as a surface functionalization agent for the development of SiO2 nanoparticles (NPs) with photoreversible tails. In detail, cinnamic acid (CINN) was activated with N-hydroxysuccinimide (NHS) to obtain the corresponding NHS-ester (CINN-NHS). Subsequently, the amine group of 3-aminopropyltriethoxysilane (APTES) was acylated with CINN-NHS leading to the generation of a novel organosilane, CINN-APTES, which was then exploited for decorating SiO2 NPs. The covalent bond to the silica surface was confirmed by solid state NMR, whereas thermogravimetric analysis unveiled a functionalization degree much higher compared to that achieved by a conventional double-step post-grafting procedure. In light of these intriguing results, the strategy was successfully extended to naturally occurring sepiolite fibers, widely employed as fillers in technological applications. Finally, a preliminary proof of concept of the photoreversibility of the obtained SiO2@CINN-APTES system has been carried out through UV diffuse reflectance. The overall outcomes prove the consistency and the versatility of the methodological protocol adopted, which appears promising for the design of hybrid NPs to be employed as building blocks for photoresponsive materials with the ability to change their molecular structure and subsequent properties when exposed to different light stimuli.

Barium Titanate Functionalization with Organosilanes: Effect on Particle Compatibility and Permittivity in Nanocomposites.

Barium titanate (BT) recently gained new interest in the preparation of dielectric and piezoelectric lead-free materials for applications in sensors, electronics, energy harvesting and storage fields. Barium titanate nanocomposites can achieve attractive performance, provided that the compatibility between ceramic particles and polymeric matrices is enhanced to the benefit of the physical properties of the final composite. Tuning the particle-matrix interface through particle functionalization represents a viable solution. In this work, surface functionalization of BT nanoparticles (NPs), obtained by hydrothermal synthesis, with 3-glycidyloxypropyltrimethoxysilane, 2-[(acetoxy(polyethyleneoxy)propyl]triethoxysilane and triethoxysilylpropoxy(polyethyleneoxy)dodecanoate, was performed after optimizing the hydroxylation process of the NPs to improve their surface reactivity and increase the yield of grafting. Solid-state nuclear magnetic resonance and thermogravimetric analysis were used to quantify the molecules grafted onto the ceramic nanoparticles. Both bare and functionalized particles were employed in the realization of epoxy- and polydimethylsiloxane (PDMS)-based nanocomposites. Functionalization was proven to be beneficial for particle dispersibility and effective for particle alignment in the PDMS matrix. Moreover, the dielectric constant measurements revealed the potential of PDMS-based nanocomposites for applications in the field of dielectric elastomers.

A novel and selective silk fibroin fragmentation method.

In the tissue-engineering field silk fibroin can be tailored to the target applications by modifying its secondary structure and molecular weight, and functionalizing the molecule with specific active groups linked to the amino acid side chains. To better tune the silk fibroin molecular weight and structural properties, we propose the creation of a lower molecular weight fibroin-derived material through a selective and tunable enzymatic attack on the fibroin chain. Cleavage at specific amino acid sites leads to precise silk fibroin fragmentation and, thus, lower molecular weight materials whose length and properties can be tuned with the enzyme concentration. The cleavage increased the presence of free amino groups, hence reactivity, and aqueous solutions of the resulting polymer remained stable for up to seven days. Films of fragmented fibroin were prepared and characterized, demonstrating that the fragmentation did not affect ß-sheet formation after methanol treatment, but differences were detected after the water-vapor annealing process, confirmed by structural and thermal analyses. The adopted fragmentation method is fast, controllable and precise, allowing the creation of a silk-derived material class that is stable in water, with a tunable molecular weight and secondary structure rearrangements, and is thus a versatile tool for the further tunability and modulation of bioengineered constructs.

Silica hairy nanoparticles: a promising material for self-assembling processes.

"Hairy" nanoparticles (HNPs), i.e. inorganic NPs functionalized with polymer chains, are promising building blocks for the synthesis of advanced nanocomposite (NC) materials having several technological applications. Recent evidence shows that HNPs self-organize in a variety of anisotropic structures, resulting in an improvement of the functional properties of the materials, in which are embedded. In this paper, we propose a three-step colloidal synthesis of spherical SiO2-HNPs, with controlled particle morphology and surface chemistry. In detail, the SiO2 core, synthesized by a modified Stöber method, was first functionalized with a short-chain amino-silane, which acts as an anchor, and then covered by maleated polybutadiene (PB), a rubbery polymer having low glass transition temperature, rarely considered until now. An extensive investigation by a multi-technique analysis demonstrates that the synthesis of SiO2-HNPs is simple, scalable, and potentially applicable to different kind of NPs and polymers. Morphological analysis shows the overall distribution of SiO2-HNPs with a certain degree of spatial organization, suggesting that the polymer coating induces a modification of NP-NP interactions. The role of the surface PB brushes in influencing the special arrangement of SiO2-HNPs was observed also in cis-1,4-polybutadiene (cis-PB), since the resulting NC exhibited the particle packing in "string-like" superstructures. This confirms the tendency of SiO2-HNPs to self-assemble and create alternative structures in polymer NCs, which may impart them peculiar functional properties.

MoS2 Based Photodetectors: A Review.

Photodetectors based on transition metal dichalcogenides (TMDs) have been widely reported in the literature and molybdenum disulfide (MoS2) has been the most extensively explored for photodetection applications. The properties of MoS2, such as direct band gap transition in low dimensional structures, strong light-matter interaction and good carrier mobility, combined with the possibility of fabricating thin MoS2 films, have attracted interest for this material in the field of optoelectronics. In this work, MoS2-based photodetectors are reviewed in terms of their main performance metrics, namely responsivity, detectivity, response time and dark current. Although neat MoS2-based detectors already show remarkable characteristics in the visible spectral range, MoS2 can be advantageously coupled with other materials to further improve the detector performance Nanoparticles (NPs) and quantum dots (QDs) have been exploited in combination with MoS2 to boost the response of the devices in the near ultraviolet (NUV) and infrared (IR) spectral range. Moreover, heterostructures with different materials (e.g., other TMDs, Graphene) can speed up the response of the photodetectors through the creation of built-in electric fields and the faster transport of charge carriers. Finally, in order to enhance the stability of the devices, perovskites have been exploited both as passivation layers and as electron reservoirs.

Influence of Sol-Gel Conditions on the Growth of Thiol-Functionalized Silsesquioxanes Prepared by In Situ Water Production.

Thiol-functionalized oligosilsesquioxanes have been synthesized by sol-gel chemistry via the in-situ water production (ISWP) approach, exploiting the esterification reaction of chloro-acetic acid and 1-propanol. The extent of hydrolysis-condensation of 3-Mercaptopropyltrimethoxysilane (McPTMS) has been studied by FT-IR and NMR spectroscopy, gel permeation chromatography (GPC) and MALDI-TOF techniques. The esterification reaction plays a key role in ruling out the oligomer structural development. In this work, we have investigated the influence of the theoretical amount of water available for the organosilane hydrolysis, defined by the ratio of chloro-acetic acid to McPTMS in the reaction mixture, and the role of different catalysts like trifluoroacetic acid (TFA) and dibutyldilauryltin (DBTL). The behavior of the catalyst is complex since, according to its nature, it may improve the kinetics of the sol-gel reactions and the esterification reaction as well. Comparing the reactions carried out with under-stoichiometric water content, the degree of condensation of the silsesquioxanes is higher if the reaction is catalyzed by TFA than by DBTL, because TFA may improve the kinetics of both hydrolysis-condensation and esterification reactions. The use of DBTL in under-stoichiometric and stoichiometric hydrolytic conditions raises the yield in ladder-like structures. The degree of condensation generally increases increasing the hydrolysis ratio as well as the yield in cage-like structures. However, when an over-stoichiometric amount of water is provided for the sol-gel reaction, condensation degree and ratio among cages and ladder-like structures appear unaffected by the employed catalyst.

A novel non-aqueous sol-gel route for the in situ synthesis of high loaded silica-rubber nanocomposites.

Silica-natural rubber nanocomposites were obtained through a novel non-aqueous in situ sol-gel synthesis, producing the amount of water necessary to induce the hydrolysis and condensation of a tetraethoxysilane precursor by esterification of formic acid with ethanol. The method allows the synthesis of low hydrophilic silica nanoparticles with ethoxy groups linked to the silica surface which enable the filler to be more dispersible in the hydrophobic rubber. Thus, high loaded silica composites (75 phr, parts per hundred rubber) were obtained without using any coupling agent. Transmission Electron Microscopy (TEM) showed that the silica nanoparticles are surrounded by rubber layers, which lower the direct interparticle contact in the filler-filler interaction. At the lowest silica loading (up to 30 phr) silica particles are isolated in rubber and only at a large amount of filler (>60 phr) the interparticle distances decrease and a continuous percolative network, connected by thin polymer films, forms throughout the matrix. The dynamic-mechanical properties confirm that the strong reinforcement of the rubber composites is related to the network formation at high loading. Both the improvement of the particle dispersion and the enhancement of the silica loading are peculiar to the non-aqueous synthesis approach, making the method potentially interesting for the production of high-loaded silica-polymer nanocomposites.

Silk fibroin-based inks for in situ 3D printing using a double crosslinking process.

The shortage of tissues and organs for transplantation is an urgent clinical concern. In situ 3D printing is an advanced 3D printing technique aimed at printing the new tissue or organ directly in the patient. The ink for this process is central to the outcomes, and must meet specific requirements such as rapid gelation, shape integrity, stability over time, and adhesion to surrounding healthy tissues. Among natural materials, silk fibroin exhibits fascinating properties that have made it widely studied in tissue engineering and regenerative medicine. However, further improvements in silk fibroin inks are needed to match the requirements for in situ 3D printing. In the present study, silk fibroin-based inks were developed for in situ applications by exploiting covalent crosslinking process consisting of a pre-photo-crosslinking prior to printing and in situ enzymatic crosslinking. Two different silk fibroin molecular weights were characterized and the synergistic effect of the covalent bonds with shear forces enhanced the shift in silk secondary structure toward ß-sheets, thus, rapid stabilization. These hydrogels exhibited good mechanical properties, stability over time, and resistance to enzymatic degradation over 14 days, with no significant changes over time in their secondary structure and swelling behavior. Additionally, adhesion to tissues in vitro was demonstrated.

Polymeric Hydrogels for Intervertebral Disc Replacement/Integration: Playing with the Chemical Composition for Tuning Shear Behavior and Hydrophilicity.

Damages to the intervertebral disc (IVD) due to improper loading or degeneration result in back pain, which is a common disease affecting an increasing number of patients. Different strategies for IVD remediation have been developed, from surgical treatment to disc replacement, by using both metallic and non-metallic materials. Hydrogels are very attractive materials due to their ability to simulate the properties of many soft tissues; moreover, their chemical composition can be varied in order to assure performances similar to the natural disc. In particular, for the replacement of the IVD outer ring, namely, the anulus fibrosus, the shear properties are of paramount importance. In this work, we produced hydrogels through the photo-induced crosslinking of different mixtures composed of two hydrophilic monofunctional and difunctional polymers, namely, poly(ethyleneglycol) methyl ether methacrylate (PEGMEMA) and poly(ethyleneglycol) dimethacrylate (PEGDMA), together with a hydrophobic molecule, i.e., tert-butyl acrylate (tBA). By changing the ratio among the precursors, we demonstrated the tunability of both the shear properties and hydrophilicity. The structural properties of hydrogels were studied by solid-state nuclear magnetic resonance (NMR). These experiments provided insights on both the structure and molecular dynamics of polymeric networks and, together with information obtained by differential scanning calorimetry (DSC), allowed for correlating the physical properties of the hydrogels with their chemical composition.

Structure of Starch-Sepiolite Bio-Nanocomposites: Effect of Processing and Matrix-Filler Interactions.

Sepiolite clay is a natural filler particularly suitable to be used with polysaccharide matrices (e.g., in starch-based bio-nanocomposites), increasing their attractiveness for a wide range of applications, such as packaging. Herein, the effect of the processing (i.e., starch gelatinization, addition of glycerol as plasticizer, casting to obtain films) and of the sepiolite filler amount on the microstructure of starch-based nanocomposites was investigated by SS-NMR (solid-state nuclear magnetic resonance), XRD (X-ray diffraction) and FTIR (Fourier-transform infrared) spectroscopy. Morphology, transparency and thermal stability were then assessed by SEM (scanning electron microscope), TGA (thermogravimetric analysis) and UV-visible spectroscopy. It was demonstrated that the processing method allowed to disrupt the rigid lattice structure of semicrystalline starch and thus obtain amorphous flexible films, with high transparency and good thermal resistance. Moreover, the microstructure of the bio-nanocomposites was found to intrinsically depend on complex interactions among sepiolite, glycerol and starch chains, which are also supposed to affect the final properties of the starch-sepiolite composite materials.

Amino-Alcohol Organic-Inorganic Hybrid Sol-Gel Materials Based on an Epoxy Bicyclic Silane: Synthesis and Characterization.

Organic-inorganic hybrids (OIHs) are a type of material that can be obtained using the sol-gel process and has the advantages of organic and inorganic moieties in a single material. Polyetheramines have been widely used in the preparation of this type of material, particularly in combination with epoxy-based alkoxysilanes. Nevertheless, epoxyciclohexylethyltrimethoxysilane (ECHETMS) is a promising alkoxysilane with an epoxy terminal group that is quite unexplored. In this work, four novel OIH materials were synthesized using the sol-gel method. The OIHs were based on Jeffamines® of different molecular weights (D-230, D-400, ED-600, and ED-900), together with ECHETMS. The materials were characterized using multinuclear solid state NMR, FTIR, BET, UV/Vis spectroscopy, EIS, and TGA. The influence of the Jeffamine molecular weight and the suitability of these materials to act as a supporting matrix for heteroaromatic probes were assessed and discussed. The materials show interesting properties in order to be applied in a wide range of sensing applications.

Ladder-like Poly(methacryloxypropyl) silsesquioxane-Al2O3-polybutadiene Flexible Nanocomposites with High Thermal Conductivity.

Ladder-like poly(methacryloxypropyl)-silsesquioxanes (LPMASQ) are photocurable Si-based gels characterized by a double-stranded structure that ensures superior thermal stability and mechanical properties than common organic polymers. In this work, these attractive features were exploited to produce, in combination with alumina nanoparticles (NPs), both unmodified and functionalized with methacryloxypropyl-trimethoxysilane (MPTMS), LPMASQ/Al2O3 composites displaying remarkable thermal conductivity. Additionally, we combined LPMASQ with polybutadiene (PB) to produce hybrid nanocomposites with the addition of functionalized Al2O3 NPs. The materials underwent thermal stability, structural, and morphological evaluations via thermogravimetric analysis (TGA), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), Fourier transform infrared spectroscopy (FTIR), and solid-state nuclear magnetic resonance (NMR). Both blending PB with LPMASQ and surface functionalization of nanoparticles proved to be effective strategies for incorporating a higher ceramic filler amount in the matrices, resulting in significant increases in thermal conductivity. Specifically, a 113.6% increase in comparison to the bare matrix was achieved at relatively low filler content (11.2 vol%) in the presence of 40 wt% LPMASQ. Results highlight the potential of ladder-like silsesquioxanes in the field of thermally conductive polymers and their applications in heat dissipation for flexible electronic devices.

Interplay between coordination sphere engineering and properties of nickel diketonate-diamine complexes as vapor phase precursors for the growth of NiO thin films.

NiO-based films and nanostructured materials have received increasing attention for a variety of technological applications. Among the possible strategies for their fabrication, atomic layer deposition (ALD) and chemical vapor deposition (CVD), featuring manifold advantages of technological interest, represent appealing molecule-to-material routes for which a rational precursor design is a critical step. In this context, the present study is focused on the coordination sphere engineering of three heteroleptic Ni(II) ß-diketonate-diamine adducts of general formula [NiL2TMEDA] [L = 1,1,1-trifluoro-2,4-pentanedionate (tfa), 2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octanedionate (fod) or 2,2,6,6-tetramethyl-3,5-heptanedionate (thd), and TMEDA = N,N,N',N'-tetramethylethylenediamine]. Controlled variations in the diketonate structure are pursued to investigate the influence of steric hindrance and fluorination degree on the chemico-physical characteristics of the compounds. A multi-technique investigation supported by density functional calculations highlights that all complexes are air-insensitive and monomeric and that their thermal properties and fragmentation patterns are directly dependent on functional groups in the diketonate ligands. Preliminary thermal CVD experiments demonstrate the precursors' suitability for the obtainment of NiO films endowed with flat and homogeneous surfaces, paving the way to future implementation for CVD end-uses.

In Situ 3D Printing: Opportunities with Silk Inks.

In situ 3D printing is an emerging technique designed for patient-specific needs and performed directly in the patient's tissues in the operating room. While this technology has progressed rapidly, several improvements are needed to push it forward for widespread utility, including ink formulations and optimization for in situ context. Silk fibroin inks emerge as a viable option due to the diverse range of formulations, aqueous processability, robust and tunable mechanical properties, and self-assembly via biophysical adsorption to avoid exogenous chemical or photochemical sensitizer additives, among other features. In this review, we focus on this new frontier of 3D in situ printing for tissue regeneration, where silk is proposed as candidate biomaterial ink due to the unique and useful properties of this protein polymer.

Electron and Energy Transfer Mechanisms: The Double Nature of TiO2 Heterogeneous Photocatalysis.

Photocatalytic chemical transformations in the presence of irradiated TiO2 are generally considered in terms of interfacial electron transfer. However, more elusive energy-transfer-driven reactions have been also hypothesized to occur, mainly on the basis of the indirect evidence of detected reaction products whose existence could not be justified simply by electron transfer. Unlike in homogeneous and colloidal systems, where energy transfer mechanisms have been investigated deeply for several organic syntheses, understanding of similar processes in heterogeneous systems is at only a nascent level. However, this gap of knowledge can be filled by considering the important achievements of synthetic heterogeneous photocatalysis, which bring the field closer to industrial exploitation. The present manuscript summarizes the main findings of previous literature reports and, also on the basis of some novel experimental evidences, tentatively proposes that the energy transfer in TiO2 photocatalysis could possess a Förster-like nature.

Effect of Hydrothermal Treatment and Doping on the Microstructural Features of Sol-Gel Derived BaTiO3 Nanoparticles.

Barium Titanate (BaTiO3) is one of the most promising lead-free ferroelectric materials for the development of piezoelectric nanocomposites for nanogenerators and sensors. The miniaturization of electronic devices is pushing researchers to produce nanometric-sized particles to be embedded into flexible polymeric matrices. Here, we present the sol-gel preparation of crystalline BaTiO3 nanoparticles (NPs) obtained by reacting barium acetate (Ba(CH3COO)2) and titanium (IV) isopropoxide (Ti(OiPr)4). The reaction was performed both at ambient conditions and by a hydrothermal process carried on at 200 °C for times ranging from 2 to 8 h. Doped BaTiO3 nanoparticles were also produced by addition of Na, Ca, and Bi cations. The powders were annealed at 900 °C in order to improve NPs crystallinity and promote the cubic-to-tetragonal (c⟶t) phase transformation. The microstructural features of nanoparticles were investigated in dependence of both the hydrothermal reaction time and the presence of dopants. It is found that short hydrothermal treatment (2 h) can produce BaTiO3 spherical and more homogeneous nanoparticles with respect to longer hydrothermal treatments (4 h, 6 h, 8 h). These particles (2 h) are characterized by decreased dimension (approx. 120 nm), narrower size distribution and higher tetragonality (1.007) in comparison with particles prepared at ambient pressure (1.003). In addition, the short hydrothermal treatment (2 h) produces particles with tetragonality comparable to the one obtained after the longest process (8 h). Finally, dopants were found to affect to different extents both the c⟶t phase transformation and the crystallite sizes.

A Bio-inspired Multifunctionalized Silk Fibroin.

A bio-inspired multifunctionalized silk fibroin (BMS) was synthesized in order to mimic the interaction of nidogen with the type IV collagen and laminin of basement membranes. The designed BMS consists of a motif of laminin α-chain-derived, called IK peptide, and type IV collagen covalently bound to the silk fibroin (SF) by using EDC/NHS coupling and a Cu-free click chemistry reaction, respectively. Silk fibroin was chosen as the main component of the BMS because it is versatile and biocompatible, induces an in vivo favorable bioresponse, and moreover can be functionalized with different methods. The chemical structure of BMS was analyzed by using X-ray photoelectron spectroscopy, attenuated total reflection-Fourier transform infrared, cross-polarization magic angle spinning nuclear magnetic resonance techniques, and colorimetric assay. The SF and BMS solutions were cross-linked by sonication to form hydrogels or casted to make films in order to evaluate and compare the early adhesion and viability of MRC5 cells. BMS hydrogels were also characterized by rheological and thermal analyses.

Design of a Zn Single-Site Curing Activator for a More Sustainable Sulfur Cross-Link Formation in Rubber.

ZnO is a worldwide used activator for a rubber vulcanization process, which promotes fast curing kinetics and high cross-linking densities of rubber nanocomposites (NCs). However, its extended use together with leaching phenomena occurring during the production and life cycle of rubber products, especially tires, entails potential environmental risks, as ecotoxicity toward aquatic organisms. Pushed by this issue, a novel activator was developed, which introduces highly dispersed and active zinc species in the vulcanization process, reducing the amount of employed ZnO and keeping high the curing efficiency. The activator is constituted by Zn(II) single sites, anchored on the surface of SiO2 nanoparticles (NPs) through the coordination with functionalizing amino silane groups. It behaves as a double-function material, acting at the same time as a rubber reinforcing filler and a curing activator. The higher availability and reactivity of the single-site Zn(II) centers toward curative agents impart faster kinetics and higher efficiency to the vulcanization process of silica/isoprene NCs, compared to conventionally used ZnO activators. Moreover, the NCs show a high cross-linking degree and improved dynamic mechanical properties, despite the remarkably lower amount of zinc employed than that normally used for rubber composites in tires. Finally, the structural stability of Zn(II) single sites during the curing reactions and in the final materials may represent a turning point toward the elimination of zinc leaching phenomena.

Features and application of coupled cold plasma and photocatalysis processes for decontamination of water.

Dielectric barrier discharge plasma and photocatalysis have been proposed as tools for decontamination of process water, especially in food industry. The present investigation aims to redefine and identify the features of coupling the two technologies in terms of degradation efficiency of a model compound. Results show that, when the process is carried out in plasma activated water in the presence of irradiated TiO2, the efficiency of the integrated process is lower than the sum of the two processes acting separately. It is proposed that afterglow species, e.g. hydrogen peroxide and/or peroxynitrites could be activated by UVA light irradiation producing hydroxyl radicals in the liquid phase. Even if TiO2 limits this additional effect by acting as UVA screen barrier material, its decontamination efficiency under certain conditions results higher than that obtained with plasma systems. These results open the route to chlorine-free decontamination processes and redefine the application framework of this integrated approach.

Facile preparation of a cobalt diamine diketonate adduct as a potential vapor phase precursor for Co3O4films.

Co3O4 thin films and nanosystems are implemented in a broad range of functional systems, including gas sensors, (photo)catalysts, and electrochemical devices for energy applications. In this regard, chemical vapor deposition (CVD) is a promising route for the fabrication of high-quality films in which the precursor choice plays a key role in the process development. In this work, a heteroleptic cobalt complex bearing fluorinated diketonate ligands along with a diamine moiety [Co(tfa)2·TMEDA; tfa = 1,1,1-trifluoro-2,4-pentanedionate and TMEDA = N,N,N',N'-tetramethylethylenediamine] is investigated as a potential Co molecular precursor for the CVD of Co3O4 systems. For the first time, the compound is characterized by crystal structure determination and comprehensive analytical studies, focusing also on its thermal properties and fragmentation patterns, important figures of merit for a CVD precursor. The outcomes of this investigation, accompanied by detailed theoretical studies, highlight its very favorable properties for CVD applications. In fact, growth experiments under oxygen atmospheres containing water vapor revealed the suitability of Co(tfa)2·TMEDA for the fabrication of high-quality, phase-pure Co3O4 thin films. The versatility of the proposed strategy in tailoring Co3O4 structural/morphological features highlights its potential to obtain multi-functional films with controllable properties for a variety of eventual technological end-uses.