In Situ Oxidation of Pyridyl-Dihydrobenzoimidazoquinazoline and the Synthesis of a Highly Luminescent Cd(II) Coordination Polymer: A Promising Candidate for Mutagenic Nitroaromatic Detection and Device Fabrication.

Pyridyl-substituted imidazoquinoline, a potent fluorescent framework, is advantageous to architect multifunctional coordination networks for sensing and fabricating emergent electrical conductors. In this work, a Cd(II)-based one-dimensional (1D) coordination polymer (1D CP), [Cd(glu)2(pbiq)2(H2O)]n (1), [H2glu = glutaric acid and pbiq = 4-(6-(pyridin-4-yl)benzo[4,5]imidazo[1,2-c]quinazoline)], has been structurally confirmed by single-crystal X-ray crystallography. The H-bonding and π···π interactions built a three-dimensional (3D) supramolecular structure that strongly emits at 416 nm in acetonitrile suspension. Potentially intrusive nitroaromatics (NAs) and trinitrophenol (TNP) selectively quench the strong emission of 1, and the highest quenching is noted in the case of TNP. A detection limit (limit of detection (LOD)) of 1.51 × 10-7 M for TNP is determined. The band gap (3.31 eV) of 1 recognizes semiconducting behavior, and an electronic device is fabricated. The correlation of current vs voltage (I-V plot) reveals a substantial non-ohmic electrical conductivity of 1 (Λ: 1.10 × 10-5 S m-1) along with a low energy barrier (ΦB: 0.69), and the series resistance (Rs) becomes 6.21 kΩ.

Correlation in Structural Architecture toward Fabrication of Schottky Device with a Series of Pyrazine Appended Coordination Polymers.

Energy is the center of importance for the survivability of civilization. Use of fossil fuel is going to be suspended, and renewable energy is technologically costlier. In the quest for new energy sources and to minimize fuel expenditure, the design of energy efficient devices is one of the solutions. Toward this objective, highly delocalized π-acidic N-hetreocycle pyrazine bridged Cd(II)-based coordination polymers (CPs), [Cd(tppz)(adc)(MeOH)] (1), [Cd(tppz)(trep)] (2), and [Cd(tppz)(2,6-ndc)] (3; tppz = 2,3,5,6-tetrakis(2-pyridyl)pyrazine) are synthesized in combination with π-accessible dicarboxylato linkers (acetylene dicarboxylic acid (H2adc), terephthalic acid (H2trep), and 2,6-naphthalene dicarboxylic acid (2,6 H2ndc)). The structures of the compounds, 1-3, have been confirmed by single-crystal X-ray diffraction measurements. Analysis of electrical property demonstrates that light irradiation enhances the conductivity and follows the order 3 > 2 > 1; compound 3 possesses the highest conductivity (1.93 × 10-3 (light), 1.12 × 10-4 S m-1 dark)), than 2 (1.80 × 10-4 (light), 1.10 × 10-4 S m-1 (dark)) and 1 (5.06 × 10-5 (light), 4.72 × 10-5 S m-1 (dark)). This light-induced electrical conductivity can pave the way toward fabrication of an active electronic device by using the discussed materials.

Aminoisophthalate Bridged Cd(II)-2D Coordination Polymer: Structure Description, Selective Detection of Pd2+ in Aqueous Medium, and Fabrication of Schottky Diode.

Photoluminescence activity of coordination polymers (CPs) has evoked intricate applications in the field of materials science, especially sensing of ions/molecules. In the present study, 2,3,5,6-tetrakis(2-pyridyl)pyrazine (tppz) and 5-aminoisophthalate (HAIPA-) coordinated to Cd(II) to architect a coordination polymer, {[Cd(HAIPA)(tppz)(OH)]·3H2O}n (CP1) which unveils blue emission in an aqueous acetonitrile (98% aqueous) suspension. The emission is selectively quenched by Pd2+ only without interference in the presence of as many as 16 other cations. The structure of CP1 shows the presence of a free -COOH group, and the interlayer (-CO)O(2)···O(7) (OC-) distance, 4.242 Å, along with the π···π interactions (3.990, 3.927 Å), may make a cavity which suitably accommodates only Pd2+ (van der Waal's radius, 1.7 Å) through the Pd(II)-carboxylato (-COO-Pd) coordination. The stability of the composite, [CP1 + Pd2+] may be assessed from the fluorescence quenching experiment, and the Stern-Volmer constant (KSV) is 7.2 × 104 M-1. Therefore, the compound, CP1, is a promising sensor for Pd(II) in a selective manner with limit of detection (LOD), 0.08 µM. The XPS spectra of CP1 and [CP1 + Pd2+] have proven the presence of Pd2+ in the host and the existence of a coordinated -COO-Pd bond. Interestingly, inclusion of Pd2+ in CP1 decreases the band gap from 3.61 eV (CP1) to 3.05 eV ([CP1 + Pd2+]) which lies in the semiconducting region and has exhibited improved electrical conductivity from 7.42 × 10-5 (CP1) to 1.20 × 10-4 S m-1 ([CP1 + Pd2+]). Upon light irradiation, the electrical conductivities are enhanced to 1.45 × 10-4 S m-1 (CP1) and 3.81 × 10-4 S m-1 ([CP1 + Pd2+]); which validates the highly desired photoresponsive device applications. Therefore, such type of materials may serve as SDG-army (sustainable development goal) to battle against the environmental issues and energy crisis.

Pyridyl-Isonicotinoyl Hydrazone-Bridged Zn(II) Coordination Framework with Thiophenedicarboxylato Link: Structure, Biological Activity, and Electrical Conductivity.

Multidimensional applicability of functional materials is one of the focal attractions in today's scientific research. Highly stable and crystalline coordination polymers served as one of the active members in the club of multifunctional materials. Toward this concept, a 3-dimensional (3D) coordination framework, {[Zn2(tdc)2(pcih)2]n} (1) (tdc2-, 2,5-thiophene dicarboxylate; pcih, pyridine-4-carboxaldehyde isonicotinoyl hydrazine), is designed and has been structurally well characterized by single crystal X-ray crystallography. One of the carboxylate groups of tdc2- chelates to Zn(II), while the other carboxylato group (-COO) acts as bridging-O to neighboring Zn(II); the pcih serves as pyridyl-N bridging motif to two Zn(II) centers. The optical band gap, 3.83 eV (Tauc's plot), implies probable semiconducting ability of the material. Interestingly, the device fabricated using compound 1 measures the electrical conductivity, 2.21 × 10-5 S cm-1, and series resistance (Rs), 807 Ω, at the dark phase, which are improved significantly to 6.36 × 10-5 S cm-1 and 460 Ω, respectively, under illumination conditions. Isoniazid, used to synthesize pcih and hence the Zn(II) compound 1, is a medicine; so, the medicinal efficiency of 1 is checked by measuring the anticancer activity against MDA-MB-231, HeLa, HCT-116, and HepG2 cells. It is observed that drug efficacy is highest on MDA-MB-231 cells (IC50: 19.43 ± 1.36 µM) than other cancer cells [IC50: 24.43 ± 2.02 µM (HeLa), 26.06 ± 3.48 µM (HCT-116), and 44.28 ± 3.04 µM (HepG2)]. Therefore, the material has significant contribution in the area of energy and health toward the sustainable development goals.

Sunlight-Induced In Situ Isomerization of Both Ligands in a Mixed-Ligand Coordination Polymer: From Photosalient to Photoinert Crystals.

Reaction of Zn(NO3 )2 ⋅ 6H2 O, maleic acid (H2 mal) and trans-4-(1-naphthylvinyl)pyridine (trans-nvp) in the dark results in the formation of a one-dimensional coordination polymer (1D CP) [Zn(mal)(trans-nvp)] (1), which is photosalient in nature. The crystals of 1 pop violently under UV light and moderately in sunlight, and generate cyclobutane ligands. However, the same reaction mixture kept in visible light exhibits the rare example of in situ isomerization of both ligands: cis-trans transformation of maleate and trans-cis isomerization of the nvp ligands, and subsequent formation of another 1D CP [Zn(fum)(cis-nvp)2 (H2 O)2 ] (2, H2 fum=fumaric acid), which is found to be photoinert. Thus, altering the reaction condition from dark to visible light gives rise to photosalient to photoinert crystals.

A Dual Functional 2D MOF Exhibiting Rare Photosalient Effect as well as Selective Pd(II) Sensing in Aqueous Medium.

A Zn(II) based two-dimensional metal-organic framework (2D MOF) [Zn2(suc)2(4-nvp)2] (1) [H2suc = succinic acid and 4-nvp = 4-(1-naphthylvinyl)pyridine] exhibits a "photosalient effect" under UV light as well as sunlight along with the release of a stereoselective cyclobutane ligand, 1,3-bis(4'-pyridyl)-2,4-bis(naphthyl)cyclobutane (rctt-4-pncb). Photolysis of in situ generated MOF in solution also leads to the formation of rctt-4-pncb crystals. Interestingly, compound 1 shows a high selectivity for Pd(II) sensing in aqueous medium.

Spectrophotometric Determination of Trace Amount of Total FeII/FeIII and Live Cell Imaging of a Carboxylato Zn(II) Coordination Polymer.

The coordination polymer, (Zn(II)-CP, 1), {[Zn(2,6-NDC)(4-Cltpy)](H2O)4} (1) (2,6-H2NDC = 2,6-naphthalene dicarboxylic acid and 4-Cltpy = 4'-chloro-[2,2';6',2″]terpyridine) is structurally characterized by single crystal X-ray diffraction measurement and other physicochemical studies (PXRD, FTIR, thermal analysis, microanalytical data). 4-Cltpy acts as end-capping ligand, and NDC2- is a carboxylato bridging motif to constitute ZnN3O2 distorted trigonal bipyramid core that propagates to construct 1D chain. The coordination polymer, 1, detects total iron (Fe3+ and Fe2+) in aqueous solution by visual color change, colorless to pink. Absorption spectrophotometric technique in aqueous medium measures the limit of detection (LOD) 0.11 µM (Fe2+) and 0.15 µM (Fe3+), and binding constants (Kd) are 6.7 × 104 M-1 (Fe3+) and 3.33 × 104 M-1 (Fe2+). Biocompatibility of 1 is examined in live cells, and intracellular Fe2+ and Fe3+ are detected in MDA-MB 231 cells. Zn(II) substitution is assumed upon addition of FeIII/FeII solution to the suspension of the coordination polymer, 1, in water-acetonitrile (41:1) (LZnII + FeIII/II → LFeIII + ZnII, where L is defined as coordinated ligands), which is accompanied by changing from colorless to pink at room temperature. The color of the mixture may be assumed to the charge transfer transition from carboxylate-O to Cltpy via Fe(II/III) bridging center (carboxylate-O-Fe-CltPy). The product isolated from the reaction is finally characterized as Fe(III)@1-CP. It is presumed that product Fe(II)@1-CP may undergo fast aerial oxidation to transform Fe(III)@1-CP. The FeIII exchanged framework (Fe(III)@1-CP) has been characterized by PXRD, IR, TGA and energy dispersive X-ray analysis (EDX)-SEM. The MTT assay calculates the cell viability (%), and the tolerance limit is 100 µM to total Fe2+ and Fe3+.

Cu(II)-Based Molecular Hexagons Forming Honeycomb-like Networks Exhibit High Electrical Conductivity.

Four new Cu(II)-based hexagonal complexes with the metallomacrocycle formulae [Cu6(5-nip)6(3-py)6(H2O)12] (1), [Cu6(5-nip)6(3-Clpy)6(H2O)12] (2), [Cu6(5-nip)6(3-Brpy)6(H2O)12] (3), and [Cu6(5-nip)6(3-Ipy)6(H2O)12] (4) have been synthesized using 5-nitroisophthalic acid (H25-nip) and pyridine (py)/3-halopyridine (3-Xpy; X = Cl, Br, and I) ligands. The structural features and supramolecular interactions of compounds 1-4 have been investigated using the single-crystal X-ray diffraction (SCXRD) technique. Interestingly, the hexagonal complexes undergo hydrogen bonding and π···π stacking interactions to form fascinating two-dimensional (2D) honeycomb-like structures. The synthesized complexes exhibit high electrical conductivity, arising from charge transport through space via π···π contacts. However, complexes containing 3-Brpy (3) and 3-Ipy (4) exhibit photosensitivity due to the presence of halogens with a larger size and lower ionization energy. The conductivity results are also in accordance with the theoretical prediction calculated by density functional theory (DFT) study.

Two-Dimensional MOF Modulated Fiber Nanogenerator for Effective Acoustoelectric Conversion and Human Motion Detection.

The real-time application of piezoelectric nanogenerators (PNGs) under a harsh environment remains a challenge due to lower output performance and poor durability. Thus, the development of flexible, sensitive, and stable PNGs became a topic of interest to capture different human motions including gesture monitoring to speech recognition. Herein, a scalable approach is adapted where naphthylamine bridging a [Cd(II)-µ-I4] two-dimensional (2D) metal-organic framework (MOF)-reinforced poly(vinylidene fluoride) (PVDF) composite nanofibers mat is prepared to fabricate a flexible and sensitive composite piezoelectric nanogenerator (C-PNG). The needle-shaped MOF was successfully synthesized by the layering and diffusion of two different solutions. The incorporation of single-crystalline 2D MOF ensures a large content of electroactive phases (98%) with a resultant high-magnitude piezoelectric coefficient of 41 pC/N in a composite nanofibers mat due to the interfacial specific interaction with -CH2-/-CF2- dipoles of PVDF. As an outcome, C-PNG generates high electrical output (open-circuit voltage of 22 V and maximum power density of 24 µW/cm2) with a very fast response time (tr ≈ 5 ms) under periodic pressure imparting stimuli. Benefiting from bending and twisting functionality, C-PNG is capable of scavenging biomechanical energy by mimicking complex musculoskeletal motions that broaden its application in wearable electronics and fabric integrated medical devices. In addition, C-PNG also demonstrates an efficient acoustic vibration to electric energy conversion capability with an improved power density and acoustic sensitivity of 6.25 µW and 0.95 V/Pa, respectively. The overall energy conversion efficiency is sufficient to operate several consumer electronics without any energy storage unit. This acoustic observation is further validated by the finite element method-based theoretical simulation. Overall, the 2D MOF-based device design strategy opens up a new possibility to develop a human-motion compatible energy generator and a self-powered acoustic sensor to power up electronic gadgets as well as low-frequency noise detection.

Effect of Angiotensin Converting Enzyme Inhibitors/Angiotensin Receptor Blockers on COVID-19 outcome: A Record Based Observational Study in West Bengal.

BACKGROUND: Since its first identification in December 2019, in WUHAN (CHINA), SARS-COV-2, causative agent of Corona virus pandemic, has affected millions of people worldwide, causing thousands of death. There is much speculation about the interplay between ACEI/ARB and Corona virus infection, as for internalization into host cell SARS-COV-2 binds through S spike protein to ACE-2, aided TMPRSS2. METHODS: A record based observational study has been conducted (data obtained from the clinics of fourteen physicians) in two worst affected districts of West Bengal, to find out the association of ACEI/ARB on patients, suffering from Corona virus infection. The study-protocol has already been approved by Clinical Research Ethics Committee of Calcutta School of Tropical Medicine. (IEC Ref. No: CREC-STM/2020-AS-37) Results: Increasing age, male sex and presence of co-morbidities (viz. Diabetes, COPD) are significantly associated with the occurrence of moderate and severe disease. Drugs (viz. ACEI/ARB), though are associated with less severe disease, have not achieved statistical significance, in the present study. CONCLUSION: Drugs, like ACEI/ARB, should be continued in patients suffering from COVID-19 infection, (if they are already on these drugs).

Sunlight-Induced Topochemical Photodimerization and Switching of the Conductivity of a Metal-Organic Compound.

A metal-organic compound [Cd(quin)2(4-nvp)2] [1; Hquin = quinoline-2-carboxylic acid and 4-nvp = 4-(1-naphthylvinyl)pyridine] undergoes topochemical [2 + 2] cycloaddition by sunlight irradiation to generate a one-dimensional coordination polymer. This reaction is thermally reversible, and switching between two crystalline forms can be monitored by conductivity measurements.

Supramolecular Aggregate of Cadmium(II)-Based One-Dimensional Coordination Polymer for Device Fabrication and Sensor Application.

A novel mixed ligand one-dimensional coordination polymer (1D CP), {[Cd2(adc)2(4-nvp)6]·(MeOH)·(H2O)} n (1; H2adc = 9,10-anthracenedicarboxylic acid, and 4-nvp = 4-(1-naphthylvinyl)pyridine), has been synthesized and structurally characterized by single crystal X-ray crystallography. The 1D polymer undergoes supramolecular aggregation via hydrogen bonding, C-H···π, and π···π interactions. Interestingly, compound 1 shows increasing conductivity upon irradiation of light. Therefore, it has the potential to be used in optoelectronic devices. Moreover, the supramolecular assembly of 1 specifically detects Cr3+ cation in the presence of other competitive analytes. Most importantly, compound 1 exhibits fascinating turn-on Cr3+ sensing, which seems to be an ornament in the field of sensing application.

Photochemical Structural Transformation of a Linear 1D Coordination Polymer Impacts the Electrical Conductivity.

A pair of 4-(1-naphthylvinyl)pyridine (4-nvp) ligands has been successfully aligned in head-to-tail fashion in a one-dimensional (1D) double chain ladder polymer [Cd(adc)(4-nvp)2(H2O)] n (1; H2adc = acetylenedicarboxylic acid) that undergoes a photochemical [2 + 2] cycloaddition reaction accompanied by single-crystal to single-crystal (SCSC) structural transformation from a 1D chain to a 2D layer structure. These structural changes have a significant impact on the conductivity and Schottky nature of the compound.

Electrical property and Schottky behavior of a flexible Schiff-base compound: X-ray structure and stabilization of 1D water chain.

The flexible Schiff-base compound 2,2'-((1,4-phenylenebis-(methylene))bis(sulfanediyl))bis(N-(pyridin-4-ylmethylene)aniline) (1; pbbpa) has been synthesized by a two-step synthetic procedure and characterized by elemental analysis, infrared (IR) spectroscopy, powder X-ray diffraction (PXRD) pattern and single crystal X-ray diffraction (SCXRD) technique. The compound exhibits electrical conductivity in the semiconducting region, as revealed by band gap calculation and further confirmed by density functional theory (DFT) computations. Interestingly, the compound formed a Schottky interface with aluminum (Al) metal, which is supported by the impedance spectroscopy (IS)-based network analysis. Besides, SCXRD of compound 1 reveals the formation of a one-dimensional (1D) water chain encapsulated by the hydrogen bonded supramolecular network.

Cobalt-Based Nanoscale Material: An Emerging Electrocatalyst for Hydrogen Production.

Modern civilization has been highly suffering from energy crisis and environmental pollutions. These two burning issues are directly and indirectly created from fossil fuel consumption and uncontrolled industrialization. The above critical issue can be solved through the proper utilization of green energy sources where no greenhouse gases will be generated upon burning of such materials. Hydrogen is the most eligible candidate for this purpose. Among various methods of hydrogen generation, electrocatalytic process is one of the most efficient methods because of easy handling and high efficiency. In these aspects Co-based nanomaterials are considered to be extremely significant as they can be utilized as efficient, recyclable and ideal catalytic system. In this article a series of Co-based nano-electrocatalysts has been discussed with proper structure-property relationship and their medium dependency. Therefore, such type of stimulating summary on recently reported electrocatalysts and their activity may be helpful for scientists of the corresponding field as well as for broader research communities. This can be inspiration for materials researchers to fabricate active catalysts for the production of hydrogen gas in room temperature.

Exploitation of a 1D coordination polymer as a portable kit for an eye-catching fluorometric response towards sensing of trivalent cations.

The development and utilization of coordination polymers (CPs) have drawn interest for potential applications in different fields. Detection of metal ions in efficient and selective manners is an important field of research. It paves the way to protect human health by balancing toxic metal ions and biologically active metal ions in the atmosphere. In this regard, a new one-dimensional (1D) 4-(1-naphthylvinyl)pyridine (4-nvp) based CP [Cd(NCS)2(4-nvp)2]n (1) was synthesized and characterized structurally by single-crystal X-ray diffraction. Interestingly, this 1D CP underwent supramolecular aggregation via π⋯π stacking interactions, which specifically generated an environment for a potent "turn on" response in the presence of trivalent cations (Fe3+, Al3+, and Cr3+) in the nanomolar range but remained silent in the presence of other metal ions. Density functional theory (DFT) computations and X-ray photoelectron spectroscopy (XPS) were performed to establish the sensing phenomena. Fascinatingly, utilizing the sensitivity of 1 in an aqueous medium, a hands-on portable cotton swab kit was developed for instant identification of these three important trivalent metal cations.

Diamondoid Ni(II) Coordination Polymer as an Electrocatalyst for Hydrogen and Oxygen Evolution Reactions and Overall Water Splitting.

We have successfully synthesized a new Ni(II)-based coordination polymer (CP) [Ni2(cis-1,4-chdc)2(4,4'-bpy)3(H2O)2] (1); (cis-1,4- H2chdc=cis-1,4-cyclohexanedicarboxylic acid and 4,4'-bpy=4,4'-bipyridine) employing slow diffusion method in a single pot technique. The connectivity of Ni(II) ions and bridging cis-1,4-chdc ligand gives rise to a three-dimensional (3D) framework with 2-fold interpenetrated diamondoid topology. Interestingly, the synthesized CP acts as efficient catalyst for electrocatalytic water splitting. The water oxidation activity of compound 1 exhibits Tafel slope equivalent to 361.48 mV.dec-1 for hydrogen evolution reaction (HER) and 353.53 mV.dec-1 for oxygen evolution reaction (OER) in an alkaline medium while almost similar values of Tafel slope for HER and OER equivalent to 287.33 mV.dec-1 and 289.93 mV.dec-1 respectively in acidic medium. Thus, the compound 1 has excellent efficacy in catalyzing HER and OER in acidic as well as alkaline medium, which is ascribed to its distinctive 3D architecture.

Explosive and pollutant nitroaromatic sensing through a Cd(II) based ladder shaped 1D coordination polymer.

In the existing leanings of environmental and national security issues, establishment of appropriate sensors for explosive as well as pollutant nitroaromatic compounds may be considered as one of the most prodigious job for material researchers. In the current study a new Cd(II) based 1D ladder coordination polymer (CP), [Cd(4-bpd)(3-cbn)2]n, has been synthesized and well characterized through single crystal X-ray diffraction analysis. Interestingly, the supramolecular assembly of this compound has efficiently identified 2,4,6-trinitrophenol through fluorescence quenching method. The Stern-Volmer coefficient (Ksv) has been calculated as 6.047 × 103 M-1, which can be attributed to the quenching of the emission intensity. The limit of detection (LOD) has been determined as 0.260 µM following the 3σ method along with almost 95% fluorescence intensity reduction. FESEM study revealed that the crystalline nature of the compound has been altered upon interaction with the above mentioned nitroaromatic analyte. Theoretical studies were performed to get the insight idea of fluorescence quenching mechanism which also substantiated the experimental observation. The present study can pave the way for the fabrication of future generation technology in sensor field.

Coordination polymers: a promising candidate for photo-responsive electronic device application.

The design and synthesis of electrically conductive coordination polymers (CPs) are of special interest due to their applications in the fabrication of many environmentally benign emerging technologies, such as molecular wires, photovoltaic cells, light emitting diodes (LEDs), field effect transistors (FETs) and Schottky barrier diodes (SBDs). Owing to their structural flexibility, easy functionality and adjustable energy levels, CPs are promising candidates for providing a better pathway for superior charge transport. Again, the utilization of visible light as an external stimulus to control and manoeuvre the electrical properties of the CPs is exceptionally motivating for the development of many optoelectronic devices, such as photodetectors, photo-switches, photodiodes and chemiresistive sensors. The applications of such materials in devices will solve questions regarding the energy crisis and environmental concerns. This study provides an overview of the recent advances in the development of photo-responsive CPs and the possibility of their application in developing optoelectronic devices. In this regard, a thorough literature survey was performed and the studies related to the fabrication of photosensitive conducting CPs for applications in optoelectronic devices are listed.

Regulating photosalient behavior in dynamic metal-organic crystals.

Dynamic photoactuating crystals have become a sensation due to their potential applications in developing smart medical devices, molecular machines, artificial muscles, flexible electronics actuators, probes and microrobots. Here we report the synthesis of two iso-structural metal-organic crystals, [Zn(4-ohbz)2(4-nvp)2] (1) and [Cd(4-ohbz)2(4-nvp)2] (2) {H4-ohbz = 4-hydroxy benzoic acid; 4-nvp = 4-(1-naphthylvinyl)pyridine} which undergo topochemical [2 + 2] cycloaddition under UV irradiation as well as sunlight to generate a dimerized product of discrete metal-complex [Zn(4-ohbz)2(rctt-4-pncb)] {rctt-4-pncb = 1,3-bis(4'-pyridyl)-2,4-bis(naphthyl)cyclobutane} (1') and one-dimensional coordination polymer (1D CP) [Cd(4-ohbz)2(rctt-4-pncb)] (2') respectively, in a single-crystal-to-single-crystal (SCSC) process. The Zn-based compound demonstrates photosalient behaviour, wherein crystals show jumping, splitting, rolling, and swelling upon UV irradiation. However, the Cd-based crystals do not show such behaviour maintaining the initial supramolecular packing and space group. Thus the photomechanical behaviour can be induced by choosing a suitable metal ion. The above findings are thoroughly validated by quantitative density functional theory (DFT) calculations which show that the Zn-based crystal shifts towards an orthorhombic structure to resolve the anisotropic UV-induced mechanical strain. Furthermore, the mechano-structure-property relationship has been established by complimentary nanoindentation measurements, which are in-line with the DFT-predicted single crystal values.