RESUMO
BACKGROUND: Movement of the pelvis during implantation of total hip arthroplasty (THA) has a major influence on the positioning of the acetabular cup. Strong traction caused by retractors leads to iatrogenic pelvic lift and can thus be partly responsible for cup malpositioning. The objective of this study was to investigate such factors that influence pelvic lift. METHODS: The dynamic movement of the pelvis was measured during implantation of THA in 67 patients. This was done by measuring the acceleration using the SensorLog app on a smartphone. RESULTS: At its maximum, the pelvis was lifted by an average of 6.7°. When impacting the press-fit cup, the surgical side was raised by 4.4° compared with the time of skin incision. This lift at the time of cup implantation correlates significantly with the body mass index and the patient's abdominal and pelvic circumference. CONCLUSION: Every surgeon performing THA must be aware of the pelvic lift during an operation. Especially in patients with a high body mass index, a large abdominal circumference, or a large pelvic circumference, there is an increased risk of malpositioning of the acetabular cup. When impacting the cup, we recommend releasing the traction of the retractor, so that the pelvis can tilt back into its natural position, and thus, the anticipated cup positioning can be implemented as exactly as possible.
Assuntos
Acetábulo/cirurgia , Artroplastia de Quadril/efeitos adversos , Prótese de Quadril , Obesidade/complicações , Pelve/cirurgia , Idoso , Idoso de 80 Anos ou mais , Índice de Massa Corporal , Feminino , Humanos , Masculino , Pessoa de Meia-Idade , Movimento , Análise Multivariada , Decúbito Dorsal , Tomografia Computadorizada por Raios XRESUMO
BACKGROUND: The most common reason for revision total hip arthroplasty remains polyethylene wear. Development dysplasia of the hip and revision situations requires a conscious compromise of implant position. The surgeon should know about the consequence on wear via a possible change in hip contact force. The objective of this study is to investigate whether annual wear is dependent on hip contact force. METHODS: Forty-five inserts (DuraLoc, DePuy) that were explanted in our department were included. Three-dimensional gravimetric determination of the wear was performed by fluid displacement. Then, the hip contact force was determined using radiographs according to the Blumentritt model. RESULTS: No correlation was found between patient-specific factors and the annual wear. The hip contact force estimated by the Blumentritt model also showed no correlation between hip contact force and annual wear. Two single model parameters correlated significantly with wear: VRECAB as a ratio of the lever length of the spinocrural and the pelvitrochanteric muscles and the angle Alpha as a measure of the position of the center of rotation in relation to the greater trochanter. The greater the ratio spinocrural/pelvitrochanteric lever arm (R = 0.408, P = .005) and the greater the Alpha angle (more valgus the femoral neck) (R = 0.377, P = .011) were, the greater was the wear. CONCLUSION: These results lead to the conclusion that neither patient-specific factors nor the estimated hip contact force have a major influence on annual wear in the case of DuraLoc cups. Only a coxa valga and a small femoral offset contribute in a limited amount to an increase in wear.
Assuntos
Artroplastia de Quadril , Luxação do Quadril/cirurgia , Prótese de Quadril , Polietileno/química , Desenho de Prótese , Estresse Mecânico , Fenômenos Biomecânicos , Índice de Massa Corporal , Cerâmica , Feminino , Fêmur , Colo do Fêmur , Seguimentos , Humanos , Masculino , Metais , Radiografia , Reoperação , Estudos Retrospectivos , RotaçãoRESUMO
INTRODUCTION: The position of the cup makes a major contribution to the success of total hip arthroplasty (THA). In conventional implantation of the prosthesis without navigation, the surgeon relies on the spatial position of the pelvis. However, iatrogenic manipulation of the pelvis during different surgical steps constantly changes the position of the pelvis during the operation. The position of the pelvis is substantial for the correct placement of the cup. The objective of this study was to investigate and visualize the course of this pelvic lift and correlate it to certain surgical steps. MATERIALS AND METHODS: Pelvic lift was measured in 67 patients during implantation of a THA. This was done by measuring acceleration using the SensorLog app on a smartphone. It was placed on the patient's contralateral anterior superior iliac spine and recorded the movement of the pelvis throughout the whole surgical procedure. The position of the pelvis was allocated to each of eight relevant surgical steps during the operation. These surgical steps were normed over the time axis and transferred to a diagram. RESULTS: We found an average pelvic lift displacement of up to 14.9° upon placement in the figure-of-four position. This lift is particularly critical when exposing the acetabulum, as the true cup position can be unconsciously influenced. Average values of between 5.6° and 6.9° were found here. CONCLUSIONS: When implanting a THA in supine position, the pelvis is not fixed on the operating table. Rather, the side to be operated on is lifted to a greater or lesser degree, depending on the surgical step to be performed. The retractor traction immediately before cup implantation should be minimized. Nevertheless, it should be taken into account that anteversion of the cup implant in relation to the table plane is systematically higher than in relation to the pelvic entry plane.
Assuntos
Artroplastia de Quadril/métodos , Posicionamento do Paciente , Pelve/fisiologia , Acetábulo/cirurgia , Adulto , Idoso , Feminino , Prótese de Quadril , Humanos , Masculino , Pessoa de Meia-Idade , Movimento , Postura , Estudos ProspectivosRESUMO
The position of the acetabular cup is a major factor in the long-term outcome of total hip arthroplasty (THA). Malpositioning of the acetabular cup frequently has been reported with the use of a minimally invasive implantation technique. It remains unclear whether the limited visibility or the increased retractor traction and thus tilting of the pelvis during cup implantation is the cause. This study investigated the influence of iatrogenically related pelvic lift using an anterolateral minimally invasive THA technique. In a group of 30 consecutive patients who underwent THA via a minimally invasive anterolateral approach, iatrogenic lifting of the pelvis was measured with a smartphone using a 3-axis accelerometer and compared with patients in a historical age- and sex-matched control group who underwent THA using a transgluteal approach. Postoperatively, the inclination and anteversion of the cup was determined on pelvic radiographs. In the anterolateral group, the pelvis was lifted by a maximum of 6.3° and by an average of 3.9° when the acetabular cup was impacted; no difference was noted compared with the transgluteal group. In contrast, the cups in the anterolateral group showed significantly increased inclination and reduced anteversion. In both techniques, the iatrogenic tilting of the pelvis at the time of cup implantation occurred to a comparable extent. Therefore, the significant differences in postoperative radiographs cannot be attributed to increased retractor traction on exposure of the acetabulum, which means that the limited visibility must be responsible. [Orthopedics. 2017; 40(4):e589-e593.].