Ambient Humidity-Induced Phase Separation for Fiber Morphology Engineering toward Piezoelectric Self-Powered Sensing.

Electrospun polymeric piezoelectric fibers have a considerable potential for shape-adaptive mechanical energy harvesting and self-powered sensing in biomedical, wearable, and industrial applications. However, their unsatisfactory piezoelectric performance remains an issue to be overcome. While strategies for increasing the crystallinity of electroactive ß phases have thus far been the major focus in realizing enhanced piezoelectric performance, tailoring the fiber morphology can also be a promising alternative. Herein, a design strategy that combines the nonsolvent-induced phase separation of a polymer/solvent/water ternary system and electrospinning for fabricating piezoelectric poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE) fibers with surface porosity under ambient humidity is presented. Notably, electrospun P(VDF-TrFE) fibers with higher surface porosity outperform their smooth-surfaced counterparts with a higher ß phase content in terms of output voltage and power generation. Theoretical and numerical studies also underpin the contribution of the structural porosity to the harvesting performance, which is attributable to local stress concentration and reduced dielectric constant due to the air in the pores. This porous fiber design can broaden the application prospects of shape-adaptive energy harvesting and self-powered sensing based on piezoelectric polymer fibers with enhanced voltage and power performance, as successfully demonstrated in this work by developing a communication system based on self-powered motion sensing.

Role of supersaturated Al-C phases in mechanical properties of Al/fullerene composites.

We investigated the reinforcing effect of supersaturated Al-C phases on the mechanical properties of Al/C60 composites produced via powder metallurgy followed by thermal treatment. We controlled the fractions of C60-fullerenes, nano-scale carbides, and Al-C supersaturated phases in the Al/C60 composites by adjusting the heat-treatment temperature and duration. Furthermore, we examined the contribution of each phase on the elastic and plastic behavior of the composites using scanning acoustic microscopy (SAM) and hardness measurements. After heat treatment, a supersaturated Al-C phase and an Al carbide were formed in the Al/C composites by decomposition of individually dispersed C60. This led to enhancement of the hardness and elastic modulus of the Al/C composites heat-treated at 450 and 500 °C, while these properties were reduced in the 650 °C heat-treated composite. Notably, the 500 °C heat-treated composites showed significantly high hardness and elastic modulus (approximately 250 Hv and 77.8 GPa, respectively) owing to the substantially large contribution of the supersaturated Al-C phases, which was theoretically calculated to be 851 GPa/vol% and 227 GPa/vol%, respectively. This is possibly because the well-dispersed C in the atomic scale changed the elastic bonding characteristics of the metallic bonds between the Al atoms.

Near-field sub-diffraction photolithography with an elastomeric photomask.

Photolithography is the prevalent microfabrication technology. It needs to meet resolution and yield demands at a cost that makes it economically viable. However, conventional far-field photolithography has reached the diffraction limit, which imposes complex optics and short-wavelength beam source to achieve high resolution at the expense of cost efficiency. Here, we present a cost-effective near-field optical printing approach that uses metal patterns embedded in a flexible elastomer photomask with mechanical robustness. This technique generates sub-diffraction patterns that are smaller than 1/10th of the wavelength of the incoming light. It can be integrated into existing hardware and standard mercury lamp, and used for a variety of surfaces, such as curved, rough and defect surfaces. This method offers a higher resolution than common light-based printing systems, while enabling parallel-writing. We anticipate that it will be widely used in academic and industrial productions.

Generation, transport and detection of valley-locked spin photocurrent in WSe2-graphene-Bi2Se3 heterostructures.

Quantum optoelectronic devices capable of isolating a target degree of freedom (DoF) from other DoFs have allowed for new applications in modern information technology. Many works on solid-state spintronics have focused on methods to disentangle the spin DoF from the charge DoF1, yet many related issues remain unresolved. Although the recent advent of atomically thin transition metal dichalcogenides (TMDs) has enabled the use of valley pseudospin as an alternative DoF2,3, it is nontrivial to separate the spin DoF from the valley DoF since the time-reversal valley DoF is intrinsically locked with the spin DoF4. Here, we demonstrate lateral TMD-graphene-topological insulator hetero-devices with the possibility of such a DoF-selective measurement. We generate the valley-locked spin DoF via a circular photogalvanic effect in an electric-double-layer WSe2 transistor. The valley-locked spin photocarriers then diffuse in a submicrometre-long graphene layer, and the spin DoF is measured separately in the topological insulator via non-local electrical detection using the characteristic spin-momentum locking. Operating at room temperature, our integrated devices exhibit a non-local spin polarization degree of higher than 0.5, providing the potential for coupled opto-spin-valleytronic applications that independently exploit the valley and spin DoFs.