Electrodeposition of ternary compounds for novel PV application and optimisation of electrodeposited CdMnTe thin-films.

Growth of polycrystalline CdMnTe ternary compound thin films has been carried out using cathodic electrodeposition technique at different cathodic potentials. The range of the cathodic potentials used in this work has been chosen according to the cyclic voltammogram results. The CdMnTe thin films were electroplated from electrolyte containing CdSO4, TeO2 and MnSO4 in an acidic aqueous medium. Glass/fluorine-doped tin oxide (FTO) substrates have been used to electrodeposit the semiconductor layers. The structural, compositional, morphological, optical and electrical properties of the CdMnTe thin films were studied using X-ray diffraction (XRD), Sputtered neutral-mass spectroscopy (SNMS), Scanning electron microscopy (SEM), UV-Vis spectroscopy and Photo-electro-chemical (PEC) cell measurements respectively. The primarily grown as-deposited (AD) layers went through two different post-growth surface treatment conditions- heat-treated in air in the presence of CdCl2 (CCT) and heat-treated in air in the presence of GaCl3 (GCT). Results from the XRD indicated the polycrystalline nature of the electrodeposited films. The electroplated films have cubic crystal structures and the preferred orientation was found to be along the (111) plane of CdMnTe. Inclusion of Mn has been qualitatively observed using SNMS measurement. The optical energy bandgaps of the thin films were found to be varying between ~ 1.90 and ~ 2.20 eV. Though all the layers after post-treatment showed p-type electrical conduction, both p and n-type conductivity were obtained at different cathodic potentials for as-deposited materials. Comparison of the deposited layers to other electrodeposited ternary compounds has also been discussed.

Forces required to initiate sliding in second-generation intramedullary nails.

Second-generation intramedullary nails, which allow the fixation screw that is placed in the femoral head to slide distally and thus allow compression of the fracture of the femoral neck, have become a popular option for the treatment of ipsilateral fractures of the femoral neck and shaft. However, the sliding characteristics of the screw within the barrel of the nail or the side-plate have not been assessed biomechanically, to our knowledge. The goal of the current study was to investigate the forces required to initiate sliding of the proximal screw in intramedullary devices and to compare these forces with those required to initiate sliding of hip screws. The loading configuration simulated the typical angle of 135 degrees between the intramedullary nail and the proximal screw. The forces required to initiate sliding of the proximal screw, with the screw extended fifty-one, seventy-six, eighty-six, and 102 millimeters beyond the proximal end of the barrel, were measured for three different types of second-generation intramedullary nails (Recon, ZMS, and Gamma), a sliding compression hip screw, and an intramedullary hip screw, and these forces were then compared. With each amount of extension of the screw, the hip screws required lower forces to initiate sliding than did the second-generation intramedullary devices. Of the second-generation devices, the Gamma nail required the highest forces to initiate sliding; the Recon and ZMS nails required 20 to 40 percent lower forces compared with the Gamma nail. None of the devices jammed in any of the loading configurations that were tested. When the extension of the screw was increased, higher forces were required to initiate sliding.

A theoretical model of the knee and ACL: theory and experimental verification.

A three-dimensional mathematical model of the human knee joint was developed to examine the role of single ligaments, such as an anterior cruciate ligament (ACL) graft in ACL reconstruction, on joint motion and tissue forces. The model is linear and valid for small motions about an equilibrium position. The knee joint is modeled as two rigid bodies (the femur and the tibia) interconnected by deformable structures, including the ACL or ACL graft, the cartilage layer, and the remainder of the knee tissues (modeled as a single element). The model was demonstrated for the equilibrium condition of the knee in extension with an anterior tibial force, causing anterior drawer and hyperextension. The knee stiffness matrix for this condition was measured for a human right knee in vitro. Predicted model response was compared with experimental observations. Qualitative agreement was found between model and experiment, validating the model and its assumptions. The model was then used to predict the change in graft and cartilage forces and joint motion of the knee due to an increment of load in the normal joint both after ACL removal and with various altered states simulating ACL reconstructions. Results illustrate the interdependence between loads in the ACL graft, other knee structures, and contact force. Stiffer grafts and smaller maximum unloaded length of the ligament lead to higher graft and contact forces. Changes in cartilage stiffness alter load sharing between ACL graft and other joint tissues.

[Significance of hemodynamic parameters of blood loss in orthognathic surgery]. / Bedeutung hämodynamischer Parameter für den Blutverlust in der Dysgnathiechirurgie.

INTRODUCTION: The hemodynamic parameters of 95 patients undergoing maxillary or bimaxillary orthognathic surgery in 1996 and 1997 at the Department of OMF Surgery/Plastic Surgery, Krefeld, Germany, were analyzed retrospectivly to study the effect of intraoperative blood loss. MATERIALS AND METHODS: The parameters included the blood loss volume, age, weight and sex of the patients, the mode of osteotomy and the operation time, the surgeon, the average blood pressure, the infusion volume, the anesthesiologist, the thrombocyte counts and their function, the activity of the coagulation factors II, V, VII, VIII, IX, X, XI, XII, XIII and von-Willebrand-factor, and the pathological coagulation factor counts of each patient, the rate of autologous blood donation and the rate of retransfusion. Statistical analysis was done using the Speraman-Rhotest. RESULTS: The average blood loss during maxillary osteotomy was 670 +/- 380 ml and during bimaxillary surgery 1120 +/- 510 ml. Men lost about 300 ml more than women. Operations of more than 3.5 h in length led to a blood loss of 1200 +/- 520 ml as opposed to 670 +/- 310 ml. The average blood loss among various surgeons was between 670 ml and 1180 ml of various anesthesiologists between 730 ml and 1200 ml, without statistical evidence. Some 17.9% of patients showed pathological thrombocytic function concerning medication with aspirin; 34.7% had pathological activities of coagulation factors, but only 2.1% with clinical significance. CONCLUSION: Mode of operation, maxillary or bimaxillary, und length of operation were the most significant factors of intraoperative blood loss. Patients with pathological coagulation had nearly the same rate of blood loss as patients with physiological coagulation. In most cases this was determined by restriction of aspirin. Analysis of the rate of autologous blood retransfusion showed a significant correlation to blood loss in bimaxillary surgery. Maxillary osteotomy led to a retransfusion of only 14.2% of autologous blood unit. This should be reviewed critically especially concerning costs.