Effect of arsenic contaminated irrigation water on Lens culinaris L. and toxicity assessment using lux marked biosensor.

Contamination of irrigation water represents a major constraint to Bangladesh agriculture, resulting in elevated levels in the terrestrial systems. Lux bacterial biosensor technology has previously been used to measure the toxicity of metals in various environmental matrices. While arbuscular mycorrhizal fungi have their most significant effect on phosphorus uptake, but showed alleviated metal toxicity to the host plant. The study examined the effects of arsenic and inoculation with an arbuscular mycorrhizal fungus, Glomus mosseae, on lentil (Lens culinaris L. cv. Titore). Plants were grown with and without arbuscular mycorrhizal inoculum for 9 weeks in a sand and terra-green mixture (50:50, V/V) and watered with five levels of arsenic (0, 1, 2, 5, 10 mg As/L arsenate). The results showed that arsenic addition above 1 mg/L significantly reduced percentage of mycorrhizal root infection. On further analysis a close relationship was established with the vegetative and reproductive properties of lentil (L. culinaris) plants compared to the percentage bioluminescence of the soil leachate. However, arbuscular mycorrhizal fungal inoculation reduced arsenic concentration in roots and shoots. Higher concentrations of arsenic (5, 10 mg As/L arsenate) reduced the mycorrhizal efficiency to increase phosphorus content and nitrogen fixation. Therefore, this study showed that increased concentration of arsenic in irrigation water had direct implications to the lentil (L. culinaris) plants overall performance. Moreover the use of bioassay demonstrated that mycorrhiza and clay particle reduced arsenic bioavailability in soil.

An ecotoxicological approach to assessing the impact of tanning industry effluent on river health.

A study was conducted to investigate the sediment health and water quality of the River Sagana, Kenya, as impacted by the local tanning industry. Chemical analysis identified the main chemical pollutants (pentachlorophenols and chromium) while a bioassay addressed pollutant bioavailability. The bioassay, exploiting the luminescence response of a lux marked bacterial biosensor, was coupled to a dehydrogenase and Dapnia magna test to determine toxicity effects on sediments. Results highlighted the toxicity of the tannery effluent to the sediments at the point of discharge (64% of control bioluminescence) with gradual improvement downstream. There was a significant increase in dehydrogenase downstream, with the enzyme activity attaining a peak at 600 m, also indicating a gradual reduction of toxicity. Biological oxygen demand (19.56 mg L(-1)) dissolved oxygen (3.97 mg L(-1)) and high lethal dose value (85%) of D. magna also confirmed an initial stress at the point of discharge and recovery downstream. Optical density of surface water demonstrated an increase in suspended particulates and colour after the discharge point, eventually decreasing beyond 400 m. In conclusion, the study highlighted the importance of understanding the biogeochemistry of river systems impacted by industries discharging effluent into them and the invaluable role of a biosensor-based ecotoxicological approach to address effluent hazards, particularly in relation to river sediments.

Ecotoxicological screening of Kenyan tannery dust using a luminescent-based bacterial biosensor.

Ecotoxicological screening of dust sampled throughout a Kenyan tannery was conducted using a luminescence (lux)-based bacterial biosensor for both solid and liquid assays. This was complemented by chemical analysis in an attempt to identify possible causative toxic components. The biosensor results showed a highly significant (p < 0.001) difference in both solid and liquid phase toxicity in samples collected from various identified sampling points in the tannery. A positive correlation was observed between results of the solid and liquid phase techniques, for most of the sampling points indicating that the toxic contaminants were bioavailable both in the solid and liquid state. However, the results generally indicated toxicity associated with liquid phase except certain areas in solid phase such as chemical handling, buffing area and weighing. The most toxic tannery area identified was the weighing area (p < 0.001), showing the lowest bioluminescence for both the solid (0.38 +/- 2.21) and liquid phases (0.01 +/- 0.001). Chromium was the metal present in the highest concentration indicating levels higher than the stipulated regulatory requirement of 0.5 mg Cr/m3 for total Cr (highest Cr concentration was at chemical handling at 209.24 mg l(-1)) in all dust samples. The weighing area had the highest Ni concentration (1.87 mg l(-1)) and the chemical handling area showed the highest Zn concentration (31.9 mg l(-1)). These results raise environmental health concerns, as occupational exposure to dust samples from this site has been shown to give rise to elevated concentrations (above the stipulated levels) of chromium in blood, urine and some body tissues, with inhalation being the main route. Health and Safety Executive (HSE), UK, and American Conference of Governmental Industrial Hygienist (ACGIH) and National Institute for Occupational Safety and Health (NIOSH), USA stipulates an occupational exposure limit of 0.5 mg Cr/m3 (8 h TWA) for total chromium. However, schedule 1 of Controls of substances hazardous to health (COSHH) regulations developed by HSE, indicate 0.05 mg m3 (8 h TWA reference periods) to be the limit for Cr (VI) exposure. The exposure limit for individual (e.g., Cr, Zn, Ni etc.) contaminants (homogeneity) was not exceeded, but potential impact of heterogeneity (multi-element synergistic effect) on toxicity requires application of the precautionary principle.