Detection of multiclass explosives and related compounds in soil and water by liquid chromatography-dielectric barrier discharge ionization-mass spectrometry.

In this work, the multiclass detection of explosives and related compounds has been studied by liquid chromatography-high-resolution mass spectrometry by means of a time-of-flight mass spectrometer (TOFMS) operated in the negative ion mode, using dielectric barrier discharge ionization (DBDI). Reversed-phase high-performance liquid chromatography (HPLC) separation was performed using water-methanol mobile phase without any modifier, although the effect of ammonium acetate was studied. DBD plasma was generated by applying a square wave voltage of 2.5 kV to a 100-mL min-1 He flow. The DBDI probe was adjusted to fit the commercial API source housing so that the HPLC eluent was nebulized and vaporized in the same manner as for atmospheric-pressure chemical ionization (APCI). The ionization process was affected by the temperature of the two nitrogen streams used to vaporize the solvent and the analytes, particularly for RDX and HMX, which are thermolabile compounds. The best approach in terms of sensitivity for all the studied compounds was the use of a gradient of temperatures in the ionization source, starting at 225/200 °C (vaporizer/drying gas temp) for nitramines and ending at 350/325 °C for nitroaromatic compounds. High-resolution full-scan spectra of individual selected compounds were recorded by LC-DBDI-TOFMS, and the results were compared to LC-APCI-TOFMS. A better sensitivity (slope of calibration curve) was obtained by DBDI for more than 70% of the studied compounds in both wastewater and soil extracts. Graphical abstract ᅟ.

Study of different HILIC, mixed-mode, and other aqueous normal-phase approaches for the liquid chromatography/mass spectrometry-based determination of challenging polar pesticides.

The aim of the study was to evaluate the performance of different chromatographic approaches for the liquid chromatography/mass spectrometry (LC-MS(/MS)) determination of 24 highly polar pesticides. The studied compounds, which are in most cases unsuitable for conventional LC-MS(/MS) multiresidue methods were tested with nine different chromatographic conditions, including two different hydrophilic interaction liquid chromatography (HILIC) columns, two zwitterionic-type mixed-mode columns, three normal-phase columns operated in HILIC-mode (bare silica and two silica-based chemically bonded columns (cyano and amino)), and two standard reversed-phase C18 columns. Different sets of chromatographic parameters in positive (for 17 analytes) and negative ionization modes (for nine analytes) were examined. In order to compare the different approaches, a semi-quantitative classification was proposed, calculated as the percentage of an empirical performance value, which consisted of three main features: (i) capacity factor (k) to characterize analyte separation from the void, (ii) relative response factor, and (iii) peak shape based on analytes' peak width. While no single method was able to provide appropriate detection of all the 24 studied species in a single run, the best suited approach for the compounds ionized in positive mode was based on a UHPLC HILIC column with 1.8 µm particle size, providing appropriate results for 22 out of the 24 species tested. In contrast, the detection of glyphosate and aminomethylphosphonic acid could only be achieved with a zwitterionic-type mixed-mode column, which proved to be suitable only for the pesticides detected in negative ion mode. Finally, the selected approach (UHPLC HILIC) was found to be useful for the determination of multiple pesticides in oranges using HILIC-ESI-MS/MS, with limits of quantitation in the low microgram per kilogram in most cases. Graphical Abstract HILIC improves separation of multiclass polar pesticides.

Direct olive oil analysis by mass spectrometry: A comparison of different ambient ionization methods.

Analytical methods based on ambient ionization mass spectrometry (AIMS) combine the classic outstanding performance of mass spectrometry in terms of sensitivity and selectivity along with convenient features related to the lack of sample workup required. In this work, the performance of different mass spectrometry-based methods has been assessed for the direct analyses of virgin olive oil for quality purposes. Two sets of experiments have been setup: (1) direct analysis of untreated olive oil using AIMS methods such as Low-Temperature Plasma Mass Spectrometry (LTP-MS) or paper spray mass spectrometry (PS-MS); or alternatively (2) the use of atmospheric pressure ionization (API) mass spectrometry by direct infusion of a diluted sample through either atmospheric pressure chemical ionization (APCI) or electrospray (ESI) ionization sources. The second strategy involved a minimum sample work-up consisting of a simple olive oil dilution (from 1:10 to 1:1000) with appropriate solvents, which originated critical carry over effects in ESI, making unreliable its use in routine; thus, ESI required the use of a liquid-liquid extraction to shift the measurement towards a specific part of the composition of the edible oil (i.e. polyphenol rich fraction or lipid/fatty acid profile). On the other hand, LTP-MS enabled direct undiluted mass analysis of olive oil. The use of PS-MS provided additional advantages such as an extended ionization coverage/molecular weight range (compared to LTP-MS) and the possibility to increase the ionization efficiency towards nonpolar compounds such as squalene through the formation of Ag+ adducts with carbon-carbon double bounds, an attractive feature to discriminate between oils with different degree of unsaturation.

Use of dielectric barrier discharge ionization to minimize matrix effects and expand coverage in pesticide residue analysis by liquid chromatography-mass spectrometry.

Although electrospray ionization (ESI) remains the gold standard ionization source for LC-MS, it exhibits two main limitations: the occurrence of matrix effects and the limited ionization coverage towards nonpolar compounds. Dielectric barrier discharge ionization (DBDI) has gained attraction in recent years as a versatile ionization method in different applications and formats. Here, we report a thorough evaluation of DBDI as ionization interface for LC-MS, which reveals attractive advantages over ESI and atmospheric pressure chemical ionization (APCI) provided its singular ionization mechanism versatility. A suite of 80 pesticides across a wide range of physicochemical properties were selected and the results were compared with both ESI and APCI sources. Using a helium plasma operated in homogeneous regime with square-wave AC waveform and relatively low voltages (2.5 kV), not only DBDI was able to ionize compounds only amenable so far by GC-MS (eg. organochlorine species), but also offered a competitive performance in terms of sensitivity when contrasted with the commercial electrospray ionization source under equivalent conditions. Unlike ESI, DBDI mechanism occurs in the gas-phase, so the method is less affected by liquid-phase surface phenomena that yield ion suppression in ESI. Data collected in the positive ion mode revealed negligible matrix effect values (<10% suppression) for most of the studied compounds in different complex matrix extracts such as wastewater, orange or olive oil. This is also consistent with the absence of adduct formation whereas with ESI source, Na adduct formation is quite common with these species. In general, both sensitivity and average limits of quantitation for DBDI were similar to those obtained by ESI and better than APCI. Results showed that analyte coverage with DBDI is enhanced with respect to ESI and APCI sources being able to effectively analyze organochlorine compounds.

Simultaneous liquid chromatography/mass spectrometry determination of both polar and "multiresidue" pesticides in food using parallel hydrophilic interaction/reversed-phase liquid chromatography and a hybrid sample preparation approach.

Pesticide testing of foodstuffs is usually accomplished with generic wide-scope multi-residue methods based on liquid chromatography tandem mass spectrometry (LC-MS/MS). However, this approach does not cover some special pesticides, the so called "single-residue method" compounds, that are hardly compatible with standard reversed-phase (RP) separations due to their specific properties. In this article, we propose a comprehensive strategy for the integration of single residue method compounds and standard multiresidue pesticides within a single run. It is based on the use of a parallel LC column assembly with two different LC gradients performing orthogonal hydrophilic interaction chromatography (HILIC) and reversed-phase (RPLC) chromatography within one analytical run. Two sample aliquots were simultaneously injected on each column, using different gradients, being the eluents merged post-column prior to mass spectrometry detection. The approach was tested with 41 multiclass pesticides covering a wide range of physicochemical properties across several orders of log Kow (from -4 to +5.5). With this assembly, distinct separation from the void was attained for all the pesticides studied, keeping similar performance in terms of sensitivity, peak area reproducibility (<6 RSD% in most cases) and retention time stability of standard single column approaches (better than±0.1min). The application of the proposed approach using parallel HILIC/RPLC and RPLC/aqueous normal phase (Obelisc) were assessed in leek using LC-MS/MS. For this purpose, a hybrid QuEChERS (Quick, easy, cheap, effective, rugged and safe)/QuPPe (quick method for polar pesticides) method was evaluated based on solvent extraction with MeOH and acetonitrile followed by dispersive solid-phase extraction, delivering appropriate recoveries for most of the pesticides included in the study within the log Kow in the range from -4 to +5.5. The proposed strategy may be extended to other fields such as sport drug testing or environmental analysis, where the same type of variety of analytes featuring poor retention within a single chromatographic separation occurs.

Monitoring priority substances, other organic contaminants and heavy metals in a volcanic aquifer from different sources and hydrological processes.

Irrigation with reclaimed water (R) is necessary to guarantee the sustainability of semi-arid areas. Results obtained during a two years monitoring network (2009-2011) in Gran Canaria are presented, including the analysis of chemical parameters, N and S isotopes, priority substances (2008/105/EC, 2013/39/EU), other organic contaminants and heavy metals in groundwater and R used to irrigate a golf course. The aims of this work are to evaluate the contamination in a volcanic aquifer, relate the presence of organic contaminants and heavy metals with the hydrogeochemistry and identify pollution sources in the area. No priority substance exceeded the EU thresholds for surface water, although seventeen were detected in R. The most frequent compounds were hexachlorobenzene, chlorpyrifos ethyl, fluorene, phenanthrene and pyrene. These compounds were detected at low concentration, except chlorpyrifos. Chlorpyrifos ethyl, terbuthylazine, diuron, terbutryn, procymidone, atrazine and propazine exceeded the European threshold concentration for pesticides in groundwater (100ngL(-1)). Therefore, the priority substances chlorpyrifos ethyl and diuron must be included in monitoring studies. The priority pesticides chlorfenvinphos and diazinon were always detected in R but rarely in groundwater. Besides, the existence of contaminants not related to the current R irrigation has been identified. Absence of environmental problems related to heavy metals can be expected. The relationship among contaminant presence, hydrogeochemistry, including the stable isotopic prints of δ(18)O, δ(15)N and δ(34)S and preferential recharge paths has been described. The coastal well shows high values of EC, nitrate, a variable chemistry, and 50% of organic contaminants detected above 100ngL(-1). The well located in the recharge area presents a stable hydrochemistry, the lowest value of δ(15)N and the lowest contaminants occurrence. The area is an example of a complex volcanic media with several sources of contaminants such as leakages from septic tanks and sewerage, agriculture practices, irrigation with reclaimed water or urban runoff.

Evaluation of processing factors for selected organic contaminants during virgin olive oil production: Distribution of BTEXS during olives processing.

The presence of BTEXS (benzene, toluene, ethylbenzene, xylenes and styrene) in virgin olive oils can be attributed to environmental contamination, but also to biological processes during oil lipogenesis (styrene). In this work, the processing factor of BTEXS from olives to olive oil during its production was evaluated at lab-scale with an Abencor system. Benzene showed the lowest processing factor (15%), whereas toluene and xylenes showed an intermediate behavior (with 40-60% efficiency), and ethylbenzene and styrene were completely transferred (100%). In addition, an attempt to examine the contribution of potential sources to olives contamination with BTEXS was carried out for the first time. Two types of olives samples were classified according to their proximity to the contamination source (road). Although higher levels of BTEXS were found in samples close to roads, the concentrations were relatively low and do not constitute a major contribution to BTEXS usually detected in olive oil.

Evaluation of different cleanup sorbents for multiresidue pesticide analysis in fatty vegetable matrices by liquid chromatography tandem mass spectrometry.

In this article we have evaluated the performance of different sorbents for the cleanup step in multiresidue pesticide analysis in fatty vegetable matrices using QuEChERS methodology. The three different matrices tested (olive oil, olives and avocado) were partitioned using acetonitrile prior to cleanup step. Afterwards, the supernatant was purified using different sorbents: C18+PSA (primary secondary amine), Z-Sep(+) (zirconium oxide and C18 dual bonded to silica), Z-Sep (zirconium oxide bonded to silica) and a novel sorbent Enhanced Matrix Removal-Lipid (EMR) whose composition has not been disclosed. The different cleanup strategies were compared for a group of 67 representative pesticides in terms of recovery rates, matrix effects, extract cleanliness and precision using ultra-high performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS). The best extraction efficiencies in olive oil matrix were obtained using EMR, while the results for olives and avocado were pretty similar amongst the different sorbents with an overall lower performance in terms of matrix effects and recovery rates compared to olive oil data, particularly in olives due to the higher complexity and concentration of coextracted species. On the other hand, the average reproducibility was clearly better when EMR sorbent was employed in all selected matrices for most pesticides (RSD<10% for 45, 52, and 56 pesticides in avocado, olives and olive oil respectively). The best results in terms of matrix effects were also obtained with EMR; with signal suppression lower than 20% for 79%, 16% and 51% of pesticides tested in olive oil, olives and avocado respectively. Using EMR as cleanup sorbent, limits of quantitation using UHPLC-MS/MS, ranged from 0.10 to 90µgkg(-1), allowing their determination at the low concentration levels demanded by current olive oil regulations in most cases.

Determination of polar pesticides in olive oil and olives by hydrophilic interaction liquid chromatography coupled to tandem mass spectrometry and high resolution mass spectrometry.

This article reports the development of two HPLC-MS methods for the determination of polar pesticides in olive oil and olive samples by hydrophilic interaction liquid chromatography (HILIC) separation followed by mass spectrometry detection with tandem mass spectrometry using a triple quadrupole instrument operated in multiple reaction monitoring mode (HILIC-MS/MS) or electrospray time-of-flight mass spectrometry (HILIC-TOFMS). The selected polar pesticides included in the study were: amitrol, cyromazine, diquat, paraquat, mepiquat, trimethylsulfonium (trimesium, glyphosate counterion) and fosetyl aluminium. The simple sample treatment procedure was based on liquid partitioning with methanol. The performance of the sample extraction was evaluated in terms of recovery rates and matrix effects in both olive oil and olives matrices. The results obtained for olive oil were satisfactory while, due to the high complexity of olives, poor recovery rates were obtained for the extraction of diquat, paraquat and amitrol, although with a reasonable precision enabling its use in routine analysis. Similarly, matrix effects were minor in the case of olive oil (ca. 20% suppression average), while significantly higher suppression was observed for olives (30-50% suppression average). The studied approaches were found to be useful for the determination of the pesticides studied in olive oil and olives with limits of quantitation below 5µgkg(-1) in most cases when tandem mass spectrometry was used, thus being in compliance with MRLs set by current EU regulation.

Monitoring of selected priority and emerging contaminants in the Guadalquivir River and other related surface waters in the province of Jaén, South East Spain.

The province of Jaén counts with four natural parks, numerous rivers, reservoirs and wetlands; moreover, it is probably the region with higher olive oil production in the world, which makes this zone a proper target to be studied based on the European Water Framework Directive 2000/60/CE. The aim of this survey is to monitor a total number of 373 compounds belonging to different families (pesticides, PAHs, nitrosamines, drugs of abuse, pharmaceuticals and life-style compounds) in surface waters located at different points of the province of Jaén. Among these compounds some priority organic substances (regulated by the EU Directive 2008/105/EC) and pollutants of emerging concern (not regulated yet) can be found. A liquid chromatography electrospray time-of-flight mass spectrometry (LC-TOFMS) method covering 340 compounds was developed and applied, together with a gas chromatography triple-quadrupole mass spectrometry (GC-MS/MS) method which enabled the analysis of 63 organic contaminants (30 of these compounds are analyzed by LC-TOFMS as well). From April 2009 to November 2010 a total of 83 surface water samples were collected (rivers, reservoirs and wetlands). In this period numerous organic contaminants were detected, most of them at the ng L(-1) level. The most frequently priority substances found were chlorpyrifos ethyl, diuron and hexachlorobenzene. Within the other groups, the most frequently detected compounds were: terbuthylazine, oxyfluorfen, desethyl terbuthylazine, diphenylamine (pesticide family); fluorene, phenanthrene, pyrene (PAHs group), codeine, paracetamol (pharmaceuticals compounds) and caffeine, nicotine (life-style compounds). As is could be expected, the total concentration of emerging contaminants is distinctly larger than that of priority pollutants, highlighting the importance of continuing with the study of their presence, fate and effects in aquatic environments. However, concentration levels (at the ng per liter level) are low in general for both kinds of contaminants which minimizes the possible harmful effect on the environment.

Multi-residue method for the determination of over 400 priority and emerging pollutants in water and wastewater by solid-phase extraction and liquid chromatography-time-of-flight mass spectrometry.

This article describes the development and validation of a liquid chromatography high-resolution mass spectrometry method for the simultaneous determination of over 400 multi-class priority and emerging pollutants with different physicochemical properties in environmental waters (surface water and wastewater). The proposed approach is based on the use of a database consisting of retention time/exact mass (of selected ions) pairs implemented with specific software for data analysis. The targeted list comprises 430 contaminants belonging to different compound categories, including 105 multiclass pharmaceuticals (analgesics/anti-inflammatories, antibiotics, lipid regulators, ß-blockers, antiepileptic/psychiatrics ulcer healings, diuretics, hormones and bronchodilatadors), life-style products (caffeine, nicotine), 21 drugs of abuse and their metabolites, 279 pesticides and some of their more relevant metabolites, nitrosamines, flame retardants, plasticizers and perfluorinated compounds. The proposed approach included a simple offline solid phase extraction (SPE) step using polymeric cartridges (Oasis HLB) with 200mL of water sample loaded, followed by analysis by rapid resolution liquid chromatography electrospray time-of-flight mass spectrometry (LC-TOFMS) in both positive and negative modes. The identification of the positive findings is accomplished with the data from accurate masses of the target ions along with retention time data and characteristic in-source fragment ions. The overall method performance was satisfactory with limits of quantification lower than 10ngL(-1) for the 44% of studied compounds. Recoveries between 50% and 130% were obtained for the 65% of the analytes (281 compounds). Matrix effects occurring with wastewater matrices were also assessed. The developed method was applied to the determination of target analytes in real surface water and wastewater samples.

Gas chromatography triple quadrupole mass spectrometry method for monitoring multiclass organic pollutants in Spanish sewage treatment plants effluents.

In Spain, although more than 50% of urban wastewaters are currently being treated, only half of them are subjected to biological treatments and only 3% undergo advanced treatment technologies. Consequently, the application of more exhaustive wastewater treatment protocols, including the use of new and improved technologies, the application of wider and integrated quality control and water reuse strategies are a priority. We have used as a reference, the European Water Framework Directive (WFD; Directive 2000/60/CE), which establishes a framework for Community action in the field of water policy, setting a list of priority compounds to be monitored in water in order to evaluate their levels. The aim of the present study is to develop and validate a multi-residue method for the analysis of 57 multi-class organic contaminants in wastewater samples using gas chromatography coupled to triple quadrupole mass spectrometry and apply it to evaluate the presence of such compounds in different wastewater treatment plants. The proposed method is based on a sample treatment using liquid-liquid extraction with n-hexane followed by identification, confirmation and quantitation with gas chromatography tandem mass spectrometry using a triple quadrupole analyzer operating in the selected reaction monitoring mode. Three MS/MS transitions were selected for unambiguous confirmation of the target chemicals. The method was validated at two different concentration levels (15 and 150 ng L(-1)) obtaining recovery rates in the range 70-110% in most cases. The limits of quantitation obtained for most of the compounds tested were in the low nanogram per liter range (below 3 ng L(-1) in all cases). Treated and untreated effluent wastewater samples of different origin (industrial, coastal and urban) provided by several sewage treatment plants (STPs) located throughout Spain were tested. Results so far showed that most of the samples assayed did not contain large amount of these contaminants. Hexachlorobenzene was found to be the more frequently detected contaminant in the studied samples, although at levels below 5 µg L(-1).

Comparative evaluation of liquid-liquid extraction, solid-phase extraction and solid-phase microextraction for the gas chromatography-mass spectrometry determination of multiclass priority organic contaminants in wastewater.

The European Water Framework Directive (WFD) 2000/60/EC establishes guidelines to control the pollution of surface water by sorting out a list of priority substances that involves a significant risk to or via the aquatic systems. In this article, the analytical performance of three different sample preparation methodologies for the GC-MS/MS determination of multiclass organic contaminants-including priority comprounds from the WFD-in wastewater samples using gas chromatography-mass spectrometry was evaluated. The methodologies tested were: (a) liquid-liquid extraction (LLE) with n-hexane; (b) solid-phase extraction (SPE) with C18 cartridges and elution with ethyl acetate:dichloromethane (1:1 (v/v)), and (c) headspace solid-phase microextraction (HS-SPME) using two different fibers: polyacrylate and polydimethylsiloxane/carboxen/divinilbenzene. Identification and confirmation of the selected 57 compounds included in the study (comprising polycyclic aromatic hydrocarbons (PAHs), pesticides and other contaminants) were accomplished using gas chromatography tandem mass spectrometry (GC-MS/MS) with a triple quadrupole instrument operated in the multiple reaction monitoring (MRM) mode. Three MS/MS transitions were selected for unambiguous confirmation of the target chemicals. The different advantages and pitfalls of each method were discussed. In the case of both LLE and SPE procedures, the method was validated at two different concentration levels (15 and 150 ng L(-1)) obtaining recovery rates in the range 70-120% for most of the target compounds. In terms of analyte coverage, results with HS-SPME were not satisfactory, since 14 of the compounds tested were not properly recovered and the overall performance was worse than the other two methods tested. LLE, SPE and HS-SPME (using polyacrylate fiber) procedures also showed good linearity and precision. Using any of the three methodologies tested, limits of quantitation obtained for most of the detected compounds were in the low nanogram per liter range.

Conductive-diamond electrochemical oxidation of chlorpyrifos in wastewater and identification of its main degradation products by LC-TOFMS.

The electrochemical transformation of the organophosphorous insecticide chlorpyrifos (CPF) was investigated in wastewater. The oxidation of CPF was carried out in a single-compartment electrochemical flow cell working under batch operation mode, using diamond-based material as anode and stainless steel as cathode. In order to evaluate its persistence and degradation pathway, two different concentration levels (1.0 mg L(-1) and 0.1 mg L(-1)) were studied. Liquid chromatography/mass spectrometry was used for evaluation of the initial and electrolyzed solutions. The identification of CPF transformation products was performed by liquid chromatography-time of flight-mass spectrometry (LC-TOFMS). Results showed that CPF is completely removed at the end of treatment time. Analysis by LC-TOFMS allowed the identification of six degradation products (with Mw 154, 170, 197, 305 321 and 333). Three of the identified intermediates (Mw 170, 305 and 321) were completely removed at the end of electrolysis time. Interestingly, the formation of diethyl 3,5,6-trichloropyridin-2yl phosphate (chlorpyrifos oxon) and 3,5,6-trichloropyridin-2-ol was also found in previous reported degradation pathways using different degradation technologies.

Screening of emerging contaminants and priority substances (2008/105/EC) in reclaimed water for irrigation and groundwater in a volcanic aquifer (Gran Canaria, Canary Islands, Spain).

In semiarid regions, reclaimed water can be an important source of emerging pollutants in groundwater. In Gran Canaria Island, reclaimed water irrigation has been practiced for over thirty years and currently represents 8% of water resources. The aim of this study was to monitor contaminants of emerging concern and priority substances (2008/105/EC) in a volcanic aquifer in the NE of Gran Canaria where the Bandama Golf Course has been sprinkled with reclaimed water since 1976. Reclaimed water and groundwater were monitoring quarterly from July 2009 to May 2010. Only 43% of the 183 pollutants analysed were detected: 42 pharmaceuticals, 20 pesticides, 12 polyaromatic hydrocarbons, 2 volatile organic compounds and 2 flame retardants. The most frequent compounds were caffeine, nicotine, chlorpyrifos ethyl, fluorene, phenanthrene and pyrene. Concentrations were always below 50 ng L(-1), although some pharmaceuticals and one pesticide, cholrpyrifos ethyl, were occasionally detected at higher concentrations. This priority substance for surface water exceeded the maximum threshold (0.1 µg L(-1)) for pesticide concentration in groundwater (2006/118/EC). Sorption and degradation processes in soil account for more compounds being detected in reclaimed water than in groundwater, and that some contaminants were always detected in reclaimed water, but never in groundwater (flufenamic acid, propyphenazone, terbutryn and diazinon). Furthermore, erythromycin was always detected in reclaimed water (exceeding occasionally 0.1 µg L(-1)), and was detected only once in groundwater. In contrast, some compounds (phenylephrine, nifuroxazide and miconazole) never detected in reclaimed water, were always detected in groundwater. This fact and the same concentration range detected for the groups, regardless of the water origin, indicated alternative contaminant sources (septic tanks, agricultural practices and sewerage breaks). The widespread detection of high adsorption potential compounds, and the independence of concentration with origin and depths, indicates the existence of preferential flows phenomena as potential contamination route in volcanic fractured materials.

Determination of organic priority pollutants in sewage treatment plant effluents by gas chromatography high-resolution mass spectrometry.

In this work, we report the development and validation of an analytical method for the trace level determination of 14 selected (EU-directive) priority organic pollutants (namely, 1,2,3-trichlorobenzene (1,2,3-TCB), 1,2,4-trichlorobenzene, 1,3,5-trichlorobenzene, hexachloro-1,3-butadiene, pentachlorobenzene, hexachlorobenzene, alachlor, alpha-hexachloro-cyclohexane (alpha-HCH), beta-HCH, gamma-HCH (lindane), delta-HCH, tetra-brominated diphenyl ether (tetra-BDE), penta-brominated diphenyl ether and hepta-brominated diphenyl ether) in wastewater samples from 5 different sewage treatment plants (STPs) located in Spain. The proposed methodology is based on liquid-liquid extraction with n-hexane followed by identification and confirmation of the selected pollutants by gas chromatography high-resolution mass spectrometry in selected ion recording acquisition mode. Recovery studies performed with spiked wastewater samples at two different concentration levels (0.1 and 1 microg L(-1)) gave mean recoveries in the range 80-120% (except for trichlorobenzenes, ca. with 50%) with RSD values below 10% in most cases, thus confirming the usefulness of the proposed methodology for the analyses of this kind of complex samples. The obtained detection limits in effluent wastewater matrices were in the low nanogram per liter range, with values as low as 0.09 ng L(-1) for tetra-BDE and 0.3 ng L(-1) for hexachlorobenzene. Finally, the proposed methodology was successfully applied to a monitoring study intended to characterize wastewater effluents of 5 different sewage treatment plants with different major activities (Industrial, Coastal, Urban). Most of the compounds targeted were detected in the ng L(-1) range at concentrations ranging from 0.19 ng L(-1) to 135 ng L(-1) (hexachlorobenzene).

Rapid determination of BTEXS in olives and olive oil by headspace-gas chromatography/mass spectrometry (HS-GC-MS).

In this work, a straightforward, reliable and effective automated method has been developed for the direct determination of monoaromatic volatile BTEXS group (namely benzene, toluene, ethylbenzene, o-, m- and p-xylenes, and styrene) in olives and olive oil, based on headspace technique. Separation, identification and quantitation were carried out by headspace-gas chromatography-mass spectrometry (HS-GC-MS) in selected ion monitoring (SIM) mode. Sample pretreatment or clean-up were not necessary (besides olives milling) because the olives and olive oil samples are put directly into an HS vial, automatically processed by HS and then injected in the GC-MS for chromatographic analysis. The chemical and instrumental variables were optimized using spiked olives and olive oil samples at 50 µg kg(-1) of each targeted species. The method was validated to ensure the quality of the results. The precision was satisfactory with relative standard deviations (RSD (%)) in the range 1.6-5.2% and 10.3-14.2% for olive oil and olives, respectively. Limits of detection were in the range 0.1-7.4 and 0.4-4.4 µg kg(-1) for olive oil and olives, respectively. Finally, the proposed method was applied to the analysis of real olives and olive oil samples, finding positives of the studied compounds, with overall BTEXS concentration levels in the range 23-332 µg kg(-1) and 4.2-87 µg kg(-1) for olive oil and olives, respectively.