Analogue of electromagnetically induced transparency in square slotted silicon metasurfaces supporting bound states in the continuum.

In this work, a silicon metasurface designed to support electromagnetically induced transparency (EIT) based on quasi-bound states in the continuum (qBIC) is proposed and theoretically demonstrated in the near-infrared spectrum. The metasurface consists of a periodic array of square slot rings etched in a silicon layer. The interruption of the slot rings by a silicon bridge breaks the symmetry of the structure producing qBIC stemming from symmetry-protected states, as rigorously demonstrated by a group theory analysis. One of the qBIC is found to behave as a resonance-trapped mode in the perturbed metasurface, which obtains very high quality factor values at certain dimensions of the silicon bridge. Thanks to the interaction of the sharp qBIC resonances with a broadband bright background mode, sharp high-transmittance peaks are observed within a low-transmittance spectral window, thus producing a photonic analogue of EIT. Moreover, the resonator possesses a simple bulk geometry with channels that facilitate the use in biosensing. The sensitivity of the resonant qBIC on the refractive index of the surrounding material is calculated in the context of refractometric sensing. The sharp EIT-effect of the proposed metasurface, along with the associated strong energy confinement may find direct use in emerging applications based on strong light-matter interactions, such as non-linear devices, lasing, biological sensors, optical trapping, and optical communications.

Strongly resonant silicon slot metasurfaces with symmetry-protected bound states in the continuum.

In this work, a novel all-dielectric metasurface made of arrayed circular slots etched in a silicon layer is proposed and theoretically investigated. The structure is designed to support both Mie-type multipolar resonances and symmetry-protected bound states in the continuum (BIC). Specifically, the metasurface consists of interrupted circular slots, following the paradigm of complementary split-ring resonators. This configuration allows both silicon-on-glass and free-standing metasurfaces and the arc length of the split-rings provides an extra tuning parameter. The nature of both BIC and non-BIC resonances supported by the metasurface is investigated by employing the Cartesian multipole decomposition technique. Thanks to the non-radiating nature of the quasi-BIC resonance, extremely high Q-factor responses are calculated, both by fitting the simulated transmittance spectra to an extended Fano model and by an eigenfrequency analysis. Furthermore, the effect of optical losses in silicon on quenching the achievable Q-factor values is discussed. The metasurface features a simple bulk geometry and sub-wavelength dimensions. This novel device, its high Q-factors, and strong energy confinement open new avenues of research on light-matter interactions in view of new applications in non-linear devices, biological sensors, and optical communications.

Ultrahigh temperature and strain hybrid integrated sensor system based on Raman and femtosecond FBG inscription in a multimode gold-coated fiber.

In this paper, a novel approach for hybrid systems combining Raman distributed sensors with fiber Bragg grating (FBG) sensors to carry out distributed and quasi-distributed temperature/strain measurements was proposed and experimentally demonstrated. Three FBGs were inscribed by the point-by-point technique in a simple setup for type I femtosecond inscription in a pure silica core multimode gold-coated fiber. Employing a single fiber, temperatures up to 600 °C and strains up to 4144 µÉ› approximately were measured simultaneously and without interferences between both distributed and point measurements. Moreover, a new calibration technique was implemented to calibrate the distributed temperature system using the FBG measurements as reference.

Single-longitudinal mode laser structure based on a very narrow filtering technique.

A narrow filtering technique based on the spectral overlapping of two uniform FBGs and applied to obtain a Single Longitudinal Mode (SLM) laser is proposed and demonstrated in this work. The two FBGs are spectrally detuned to reduce their coincident reflection response narrowing the equivalent filter bandwidth. A proof-of-concept linear laser has been built and tested exhibiting SLM operation even with temperature and strain variations.

Recovering a fiber Bragg grating axial strain distribution from its reflection spectrum.

A processing scheme able to obtain any arbitrary intragrating strain distribution of a fiber Bragg grating (FBG) is proposed and demonstrated. The processing method employs just the intensity of the FBG reflection spectrum to obtain its deformation profile by combining a geometrical processing scheme with the particle swarm optimization technique. The technique has been evaluated using several spectra generated from very heterogeneous strain distributions and with a real spectrum obtained from a 5 mm length FBG under an asymmetric perturbation. The achieved results exhibit a good spatial resolution (Δ≈0.5 mm) and repeatability.

Sampled Fiber Bragg Grating spectral synthesis.

In this paper, a technique to estimate the deformation profile of a Sampled Fiber Bragg Grating (SFBG) is proposed and experimentally verified. From the SFBG intensity reflection spectrum, any arbitrary longitudinal axis deformation profile applied to a SFBG is estimated. The synthesis algorithm combines a custom defined error metric to compare the measured and the synthetic spectra and the Particle Swarm Optimization technique to get the deformation profile. Using controlled deformation profiles, the proposed method has been successfully checked by means of simulated and experimental tests. The results obtained under different controlled cases show a remarkable repetitiveness (< 50 µÎµ) and good spatial accuracy (< 1 mm).

Hybrid Raman-erbium random fiber laser with a half open cavity assisted by artificially controlled backscattering fiber reflectors.

A hybrid Raman-erbium random fiber laser with a half-open cavity assisted by chirped artificially controlled backscattering fiber reflectors is presented. A combination of a 2.4 km-long dispersion compensating fiber with two highly erbium-doped fiber pieces of 5 m length were used as gain media. A single random laser emission line centered at 1553.8 nm with an optical signal to noise ratio of 47 dB were obtained when pumped at 37.5 dBm. A full width at half maximum of 1 nm and a 100% confidence level output power instability as low as 0.08 dB were measured. The utilization of the new laser cavity as a temperature and strain sensor is also experimentally studied.

Microdrilled tapers to enhance optical fiber lasers for sensing.

In this work, an experimental analysis of the performance of different types of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror is presented. These artificially-controlled backscattering fiber reflectors are used in short linear cavity fiber lasers. In particular, laser emission and sensor application features are analyzed when employing optical tapered fibers, micro-drilled optical fibers and 50 µm-waist or 100 µm-waist micro-drilled tapered fibers (MDTF). Single-wavelength laser with an output power level of about 8.2 dBm and an optical signal-to-noise ratio of 45 dB were measured when employing a 50 µm-waist micro-drilled tapered optical fiber. The achieved temperature sensitivities were similar to those of FBGs; however, the strain sensitivity improved more than one order of magnitude in comparison with FBG sensors, attaining slope sensitivities as good as 18.1 pm/µÎµ when using a 50 µm-waist MDTF as distributed reflector.

Multifunctional light beam control device by stimuli-responsive liquid crystal micro-grating structures.

There is an increasing need to control light phase with tailored precision via simple means in both fundamental science and industry. One of the best candidates to achieve this goal are electro-optical materials. In this work, a novel technique to modulate the spatial phase profile of a propagating light beam by means of liquid crystals (LC), electro-optically addressed by indium-tin oxide (ITO) grating microstructures, is proposed and experimentally demonstrated. A planar LC cell is assembled between two perpendicularly placed ITO gratings based on microstructured electrodes. By properly selecting only four voltage sources, we modulate the LC-induced phase profile such that non-diffractive Bessel beams, laser stretching, beam steering, and 2D tunable diffraction gratings are generated. In such a way, the proposed LC-tunable component performs as an all-in-one device with unprecedented characteristics and multiple functionalities. The operation voltages are very low and the aperture is large. Moreover, the device operates with a very simple voltage control scheme and it is lightweight and compact. Apart from the demonstrated functionalities, the proposed technique could open further venues of research in optical phase spatial modulation formats based on electro-optical materials.

Positive-negative tunable liquid crystal lenses based on a microstructured transmission line.

In this work, a novel technique to create positive-negative tunable liquid crystal lenses is proposed and experimentally demonstrated. This structure is based on two main elements, a transmission line acting as a voltage divider and concentric electrodes that distribute the voltage homogeneously across the active area. This proposal avoids all disadvantages of previous techniques, involving much simpler fabrication process (a single lithographic step) and voltage control (one or two sources). In addition, low voltage signals are required. Lenses with switchable positive and negative focal lengths and a simple, low voltage control are demonstrated. Moreover, by using this technique other optical devices could be engineered, e.g. axicons, Powell lenses, cylindrical lenses, Fresnel lenses, beam steerers, optical vortex generators, etc. For this reason, the proposed technique could open new venues of research in optical phase modulation based on liquid crystal materials.