Nonlocal Metasurface with Chiral Exceptional Points in the Telecom-Band.

The exceptional point (EP) is the critical phase transition point in parity-time (PT) symmetry systems, offering many unique physical phenomena, such as a chiral response. Achieving chiral EP in practical applications has been challenging due to the delicate balance required between gain and loss and complicated fabrication, limiting both working band and device miniaturization. Here, we proposed a nonlocal metasurface featuring orthogonal gold nanorods, where loss modulation is achieved through rod size and lattice pitch. By tuning the coupling strength, we experimentally observed the PT symmetry phase transition and chiral EP in the telecom-band. The experimental and simulated circular conversion dichroism at EP reach 0.79 and 0.99, respectively. We also demonstrated an abrupt phase flip of a specific component near EP theoretically. This work provides a feasible scheme for exploring EP in polarized space within the telecom-band, which may find applications in polarization control, wavelength division multiplexing, ultrasensitive sensing, imaging, etc.

Linearization of wavelength sweeping lasers for the construction of 4-D FMCW LiDAR images of slow-moving objects using baseband beat note signals.

A FMCW LiDAR system of both the distributed feedback laser and external cavity laser is established in baseband beat notes, rather than up-conversion to an intermediate frequency to exclude flicker noise. Meanwhile, utilizing fast-scanning MEMS mirrors, high-quality real-time (1 fps) 4-D images of the slow-moving object (10 mm/s) can be directly constructed at the baseband with a central frequency as low as 100 kHz and a small Doppler shift. The proposed LiDAR architecture based on such a low-frequency baseband significantly improves the optical power budget on the transmitter side and eliminates the costly high-speed sampling circuits on the receiver side.

Parity-time symmetry breaking optical nanocircuit.

Gain and loss balanced parity-time (PT) inversion symmetry has been achieved across multiple platforms including acoustics, electronics, and photonics. Tunable subwavelength asymmetric transmission based on PT symmetry breaking has attracted great interest. However, due to the diffraction limit, the geometric size of an optical PT symmetric system is much larger than the resonant wavelength, which limits the device miniaturization. Here, we theoretically studied a subwavelength optical PT symmetry breaking nanocircuit based on the similarity between a plasmonic system and an RLC circuit. Firstly, the asymmetric coupling of an input signal is observed by varying the coupling strength and gain-loss ratio between the nanocircuits. Furthermore, a subwavelength modulator is proposed by modulating the gain of the amplified nanocircuit. Notably, the modulation effect near the exceptional point is remarkable. Finally, we introduce a four-level atomic model modified by the Pauli exclusion principle to simulate the nonlinear dynamics of a PT symmetry broken laser. The asymmetric emission of a coherent laser is realized by full-wave simulation with a contrast of about 50. This subwavelength optical nanocircuit with broken PT symmetry is of great significance for realizing directional guided light, modulator and asymmetric-emission laser at subwavelength scales.

Simultaneous enhancement of the bandwidth and responsivity in high-speed avalanche photodiodes with an optimized flip-chip bonding package.

The enhancement in responsivity of photodiodes (PDs) or avalanche photodiodes (APDs) with the traditional flip-chip bonding package usually comes at the expense of degradation in the optical-to-electrical (O-E) bandwidth due to the increase of parasitic capacitance. In this work, we demonstrate backside-illuminated In0.52Al0.48As based APDs with novel flip-chip bonding packaging designed to relax this fundamental trade-off. The inductance induced peak in the measured O-E frequency response of these well-designed and well-packaged APDs, which can be observed around its 3-dB bandwidth (∼30 GHz), effectively widens the bandwidth and becomes more pronounced when the active diameter of the APD is aggressively downscaled to as small as 3 µm. With a typical active window diameter of 14 µm, large enough for alignment tolerance and low optical coupling loss, the packaged APD exhibits a moderate damping O-E frequency response with a bandwidth (36 vs. 31 GHz) and responsivity (3.4 vs. 2.3 A/W) superior to those of top-illuminated reference sample under 0.9 Vbr operation, to attain a high millimeter wave output power (0 dBm at 40 GHz) and output current (12.5 mA at +8.8 dBm optical power). The excellent static and dynamic performance of this design open up new possibilities to further improve the sensitivity at the receiver-end of the next-generation of passive optical network (PON) and coherent communication systems.

Separated electrodes for the enhancement of high-speed data transmission in vertical-cavity surface-emitting laser arrays.

In this work, a novel design for the electrodes in a near quasi-single-mode (QSM) vertical-cavity surface-emitting laser (VCSEL) array with Zn-diffusion apertures inside is demonstrated to produce an effective improvement in the high-speed data transmission performance. By separating the electrodes in a compact 2×2 coupled VCSEL array into two parts, one for pure dc current injection and the other for large ac signal modulation, a significant enhancement in the high-speed data transmission performance can be observed. Compared with the single electrode reference, which parallels 4 VCSEL units in the array, the demonstrated array with its separated electrode design exhibits greater dampening of electrical-optical (E-O) frequency response and a larger 3-dB E-O bandwidth (19 vs. 15 GHz) under the same amount of total bias current (20 mA). Moreover, this significant improvement in dynamic performance does not come at the cost of any degradation in the static performance in terms of the maximum near QSM optical output power (17 mW @ 20 mA) and the Gaussian-like optical far-field pattern which has a narrow divergence angle (full-width half maximum (FWHM): 10° at 20 mA). The advantages of the separated electrode design lead to a much better quality of 32 Gbit/sec eye-opening as compared to that of the reference device (jitter: 1.5 vs. 2.8 ps) and error-free 32 Gbit/sec transmissions over a 500 m multi-mode fiber has been achieved under a moderate total bias current of 20 mA.

Reconfigurable scan lens based on an actively controlled optical phased array.

Integrated photonics provides a path for miniaturization of an optical system to a compact chip scale and offers reconfigurability by the integration of active components. Here we report a chip-scale reconfigurable scan lens based on an optical phased array, consisting of 30 actively controlled elements on the InP integrated photonic platform. By configuring the phase shifters, we show scanning of a nearly diffraction-limited focused spot with a full width at half maximum spot size down to 2.7 µm at the wavelength of 1550 nm. We demonstrate the key functions needed for a laser-scanning microscope, including light focusing, collection, and steering. We also perform confocal measurements to detect reflection at selective depths.

Engineering Giant Rabi Splitting via Strong Coupling between Localized and Propagating Plasmon Modes on Metal Surface Lattices: Observation of √N Scaling Rule.

We present a strong coupling system realized by coupling the localized surface plasmon mode in individual silver nanogrooves and propagating surface plasmon modes launched by periodic nanogroove arrays with varied periodicities on a continuous silver medium. When the propagating modes are in resonance with the localized mode, we observe a √N scaling of Rabi splitting energy, where N is the number of propagating modes coupled to the localized mode. Here, we confirm a giant Rabi splitting on the order of 450-660 meV (N = 2) in the visible spectral range, and the corresponding coupling strength is 160-235 meV. In some of the strong coupling cases studied by us, the coupling strength is about 10% of the mode energy, reaching the ultrastrong coupling regime.

Tuning of Two-Dimensional Plasmon-Exciton Coupling in Full Parameter Space: A Polaritonic Non-Hermitian System.

Non-Hermitian photonic systems with gains and/or losses have recently emerged as a powerful approach for topology-protected optical transport and novel device applications. To date, most of these systems employ coupled optical systems of diffraction-limited dielectric waveguides or microcavities, which exchange energy spatially or temporally. Here, we introduce a diffraction-unlimited approach using a plasmon-exciton coupling (polariton) system with tunable plasmonic resonance (energy and line width) and coupling strength. By designing a chirped silver nanogroove cavity array and coupling a single tungsten disulfide monolayer with a large contrast in resonance line width, we show the tuning capability through energy level anticrossing and plasmon-exciton hybridization (line width crossover), as well as spontaneous symmetry breaking across the exceptional point at zero detuning. This two-dimensional hybrid material system can be applied as a scalable and integratable platform for non-Hermitian photonics, featuring seamless integration of two-dimensional materials, broadband tuning, and operation at room temperature.

Efficient four-wave mixing based on multiple plasmonic resonance.

Plasmonic nanostructures provide a new way to improve nonlinear optical effects. As a mode of surface plasmons (SP), localized SPs can highly localize and enhance electromagnetic fields within a subwavelength volume. In this work, we developed a one-dimensional V-groove Ag nanograting. Through simulation, we realized triple-resonance enhanced four-wave mixing (FWM), in which both the excitation and signal waves are in resonance with LSPRs modified by propagating SPs, and can perfectly overlap with each other in each single nanogroove. Compared with that from a flat Ag plate, the FWM enhancement factor can be over six orders of magnitude. Next, we filled the Ag V-groove with nonlinear polymer 2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene and further improved the enhancement factor to eight orders of magnitude, together with a conversion efficiency of 1.02×10-2. Finally, by changing the water filling ratio, the FWM signal is tuned over 180 nm, while keeping the enhancement factor over seven orders of magnitude.

High-power and single-mode VCSEL arrays with single-polarized outputs by using package-induced tensile strain.

In this work, we demonstrate a novel high-power vertical-cavity surface-emitting laser (VCSEL) array with highly single-mode (SM) and single-polarized output performance without significantly increasing the intra-cavity loss and threshold current (Ith). By combining a low-loss zinc-diffusion aperture with an electroplated copper substrate, we can obtain a highly SM output (side mode suppression ratio >50dB) with a very narrow divergence angle (1/e2:∼10∘) under high output power (3.1 W; 1% duty cycle) and sustain a single polarization state, with a polarization suppression ratio of around 9 dB, under the full range of bias currents. Compared to the reference device without the copper substrate, the demonstrated array can not only switch the output optical spectra from quasi-SM to highly SM but also maintain a close threshold current value (Ith: 0.8 versus 0.7 mA per unit device) and slope efficiency. The enhancement in fundamental mode selectivity of our VCSEL structure can be attributed to the single-polarized lasing mode induced by tensile strain, which is caused by the electroplated copper substrate, as verified by the double-crystal x-ray measurement results.

Photonic technologies for autonomous cars: feature introduction.

Photonic technologies that support the low cost manufacturing needed for automotive sensors have experienced explosive developments in recent years. To date most commercially available lidar system have been direct detection time-of-flight (ToF) sensors operating at 905 nm using mechanical mirrors for beam steering. However, these sensors suffer from important drawbacks. One issue is eye-safety, which limits maximum laser powers and hence operating range. Direct detection systems must also content with potential interference issues when lots of cars operate lidar systems simultaneously. In addition, mechanical scanners are frequently bulky and may be difficult to integrate within the form factors allowed by modern vehicles.

Enhancement in speed and responsivity of uni-traveling carrier photodiodes with GaAs0.5Sb0.5/In0.53Ga0.47As type-II hybrid absorbers.

We demonstrate a top-illuminated high-speed uni-traveling carrier photodiode (UTC-PD) with a novel design in the p-type absorber, which can effectively shorten the photon absorption depth at telecommunication wavelengths (1.31~1.55 µm) and further enhance the bandwidth-efficiency product of UTC-PD. In our proposed new UTC-PD structure, the p-type In0.53Ga0.47As absorption layer is replaced by the type-II GaAs0.5Sb0.5 (p)/In0.53Ga0.47As (i) hybrid absorber. Due to the narrowing of the bandgap and enhancement of the photo-absorption process at the type-II interface between the GaAs0.5Sb0.5 and In0.53Ga0.47As layers, our device shows an over 16.7% improvement in the responsivity compared with that of UTC-PD with the same thickness of pure In0.53Ga0.47As absorber (0.7 µm) and a zero optical coupling loss. Our demonstrated device with a simple top-illuminated structure offers a large active mesa (25 µm), a wide optical-to-electrical (O-E) bandwidth (33 GHz), a high responsivity (0.7 A/W), and a high saturation current (>5 mA) under 1.31 µm optical wavelength. These promising results suggest that our proposed PD structure can fundamentally overcome the trade-off among bandwidth, efficiency, and device active diameter of high-speed PDs.

Single quantum dot controls a plasmonic cavity's scattering and anisotropy.

Plasmonic cavities represent a promising platform for controlling light-matter interaction due to their exceptionally small mode volume and high density of photonic states. Using plasmonic cavities for enhancing light's coupling to individual two-level systems, such as single semiconductor quantum dots (QD), is particularly desirable for exploring cavity quantum electrodynamic (QED) effects and using them in quantum information applications. The lack of experimental progress in this area is in part due to the difficulty of precisely placing a QD within nanometers of the plasmonic cavity. Here, we study the simplest plasmonic cavity in the form of a spherical metallic nanoparticle (MNP). By controllably positioning a semiconductor QD in the close proximity of the MNP cavity via atomic force microscope (AFM) manipulation, the scattering spectrum of the MNP is dramatically modified due to Fano interference between the classical plasmonic resonance of the MNP and the quantized exciton resonance in the QD. Moreover, our experiment demonstrates that a single two-level system can render a spherical MNP strongly anisotropic. These findings represent an important step toward realizing quantum plasmonic devices.

Fully integrated microwave frequency synthesizer on heterogeneous silicon-III/V.

We demonstrate a photonic microwave generator on the heterogeneous silicon-InP platform. Waveguide photodiodes with a 3 dB bandwidth of 65 GHz and 0.4 A/W responsivity are integrated with lasers that tune over 42 nm with less than 150 kHz linewidth. Microwave signal generation from 1 to 112 GHz is achieved.

Monolithically integrated InAs/InGaAs quantum dot photodetectors on silicon substrates.

We report InAs/InGaAs quantum dot (QD) waveguide photodetectors (PD) monolithically grown on silicon substrates. A high-crystalline quality GaAs-on-Si template was achieved by aspect ratio trapping together with the combined effects of cyclic thermal annealing and strain-balancing layer stacks. An ultra-low dark current of 0.8 nA and an internal responsivity of 0.9 A/W were measured in the O band. We also report, to the best of our knowledge, the first characterization of high-speed performance and the first demonstration of the on-chip photodetection for this QD-on-silicon system. The monolithically integrated waveguide PD shares the same platform as the previously demonstrated micro-ring lasers and can thus be integrated with laser sources for power monitors or amplifiers for pre-amplified receivers.

Interplay Between Optical Bianisotropy and Magnetism in Plasmonic Metamolecules.

The smallness of natural molecules and atoms with respect to the wavelength of light imposes severe limits on the nature of their optical response. For example, the well-known argument of Landau and Lifshitz and its recent extensions that include chiral molecules show that the electric dipole response dominates over the magneto-electric (bianisotropic) and an even smaller magnetic dipole optical response for all natural materials. Here, we experimentally demonstrate that both these responses can be greatly enhanced in plasmonic nanoclusters. Using atomic force microscopy nanomanipulation technique, we assemble a plasmonic metamolecule that is designed for strong and simultaneous optical magnetic and magneto-electric excitation. Angle-dependent scattering spectroscopy is used to disentangle the two responses and to demonstrate that their constructive/destructive interplay causes strong directional scattering asymmetry. This asymmetry is used to extract both magneto-electric and magnetic dipole responses and to demonstrate their enhancement in comparison to ordinary atomistic materials.

Polymorphisms of 23 Y-chromosome STR Loci in A Han Population in Jiangsu Province.

Objective To investigate the polymorphisms of 23 Y-STR loci in a Han population in Jiangsu province. Methods Blood samples were collected from 4821 unrelated healthy Han males in Jiangsu province. DNA templates were amplified by PowerPlex Y23 kit,and the amplification products were detected by 3500xL genetic analyzer. Then,we calculated the allele frequencies and gene diversities respectively,as well as the haplotype frequencies and haplotype diversities. Results The gene diversity of these 23 Y-STR loci ranged 0.4099-0.9696. A total of 4781 haplotypes were detected,of which 4743 were found once. The haplotype diversity was 0.99999812. Conclusion The 23 Y-STR loci used in this study are highly polymorphic in Han individuals in Jiangsu province and therefore suitable for population genetic study and forensic individual identification.

N(2)-Selective Iodofunctionalization of Olefins with NH-1,2,3-Triazoles to provide N(2)-Alkyl-Substituted 1,2,3-Triazoles.

A new method was developed to synthesize N(2)-alkyl-substituted 1,2,3-triazole through N-iodosuccinimide (NIS) mediated iodofuctionalization reaction of the alkene group with bi-, mono-, and unsubstituted NH-1,2,3-triazoles. The favored N-1 type hydrogen bond between the iodonium ion intermediate and 1,2,3-triazole was supposed to be generated, which gave the desired N(2)-alkyl triazole with a high N(2)-selectivity.

Broadband high efficiency asymmetric transmission of achiral metamaterials.

Asymmetric transmission (AT) effect has attracted great interest in recent years, due to its potential application in integrated photonics from GHz to optical frequency. To realize AT effect, numerous metamaterials have been proposed, mainly based on the chirality of the structure. In this paper, we demonstrate that achiral metamaterials can also have AT effect. Furthermore, it is shown that modal conversion is more essential than chirality to achieve AT effect. In particular, we have proposed a mirror symmetric metamaterial with broadband high efficiency AT effect for circular polarization wave operating at THz region. With further optimization of the unit cell, >80% of the central frequency bandwidth and average 74.05 (maximum150) transmission ratio can be obtained. The idea demonstrated here can also be applied to other frequency regions.

NHC-Ag(I)-Catalyzed Three-Component 1,3-Dipolar Cycloaddition To Provide Polysubstituted Dihydro-/Tetrahydrofurans.

A new method was developed to synthesize polyfunctionalized dihydrofuran and tetrahydrofuran derivatives from the three-component [2 + 2 + 1] cycloaddition of the diazoesters with aryl/alkenyl aldehydes and alkyne/olefin dipolarophiles by using a Ag(I) N-heterocyclic carbene complex as the catalyst. A carbonyl ylide intermediate was generated, which undertook an endo-type 1,3-dipolar cycloaddition to provide the desired dihydro-/tetrahydrofurans in high regio- and diastereoselectivities by using α-aryl or α-alkenyl diazoesters.