Operando Spatial and Temporal Tracking of Axial Stresses and Interfaces in Solid-state Batteries.

Solid-state batteries have the potential to replace the current generation of liquid electrolyte batteries. However, the major limitation resulting from their solid-state architecture is the gradual loss of ionic conductivity due to the loss of physical contact between the individual battery components during charging/discharging. This is mainly due to mechanical stresses caused by volume changes in the cathode and anode during lithiation and delithiation. To date, limited research has been devoted to understanding the spatio-temporal distribution of stresses during battery operation. Here, operando scanning high-energy X-ray diffraction to quantify cross-sectional axial stresses with a spatial resolution of 10 µm is used. It is shown how a non-monotonous stress distribution evolves over time during the cycling of the solid-state battery. In addition, degradation of the solid-state electrolyte in the vicinity of the lithium anode is observed and tracked periodic changes in the unit cell volume in the cathode. The presented methodology of tracking the chemo-mechanically induced stresses and interface morphology in real time in correlation with other battery parameters is believed, can provide a valuable platform for the future optimization of solid-state batteries.

Green Colloidal Synthesis of MoS2 Nanoflakes.

Currently, two approaches dominate the large-scale production of MoS2: liquid-phase exfoliation, referred to as the top-down approach, and bottom-up colloidal synthesis from molecular precursors. Known colloidal synthesis approaches utilize toxic precursors. Here, an alternative green route for the bottom-up synthesis of MoS2 nanoflakes (NFs) is described. The NFs were synthesized by colloidal synthesis using [Mo(CH3COO)2]2 and a series of sulfur (S)-precursors including thioacetamide (TAA), 3-mercaptopropionic acid (3-MPA), l-cysteine (L-CYS), mercaptosuccinic acid (MSA), 11-mercaptoundecanoic acid (MUA), 1-dodecanethiol (DDTH), and di-tert-butyl disulfide (DTBD). While TAA, an S-precursor most commonly used for MoS2 NF preparation, is a known carcinogen, the other investigated S-precursors have low or no known toxicity. High-resolution scanning transmission electron microscopy (HR-STEM) and grazing incidence wide-angle X-ray scattering (GIWAXS) confirmed that in all cases, the syntheses yielded single-layer MoS2 NFs with lateral sizes smaller than 15 nm and a well-defined crystal structure. Electronic absorption and Raman spectra showed characteristic features associated with the MoS2 monolayers. The evolution of the absorption spectra of the growth solution during the syntheses reveals how the kinetics of the NF formation is affected by the S-precursor as well as the nature of the coordinating ligands.

Protection and Disinfection Activities of Oregano and Thyme Essential Oils Encapsulated in Poly(ε-caprolactone) Nanocapsules.

The biocolonization of building materials by microorganisms is one of the main causes of their degradation. Fungi and bacteria products can have an undesirable impact on human health. The protection and disinfection of sandstone and wood materials are of great interest. In this study, we evaluated the protection and disinfection activity of oregano and thyme essential oils encapsulated in poly(ε-caprolactone) nanocapsules (Or-NCs, Th-NCs) against four types of environmental microorganisms: Pleurotus eryngii, Purpureocillium lilacinum (fungal strains), Pseudomonas vancouverensis, and Flavobacterium sp. (bacterial strains). The surfaces of sandstone and whitewood samples were inoculated with these microorganisms before or after applying Or-NCs and Th-NCs. The concentration-dependent effect of Or-NCs and Th-NCs on biofilm viability was determined by the MTT reduction assay. The results showed that Or-NCs and Th-NCs possess effective disinfection and anti-biofilm activity. Diffuse reflectivity measurements revealed no visible color changes of the materials after the application of the nanoencapsulated essential oils.

Multilayer Langmuir Film of Monodisperse Au Nanoclusters: Unusual Growth via Bilayers.

The assembly of nanomaterials into thin films is an important area in the nanofabrication of novel devices. The monodispersity of nanoparticles plays an essential role in the resulting quality of the assembled mono- and multilayers. Larger polydispersity leads to smaller lateral correlation lengths and smaller domains of aligned nanoparticles, thus resulting in more point and line defects. Perfectly monodisperse nanoparticles should therefore minimize the number of defects in the assembled films. Despite tremendous progress in reducing the polydispersity of nanoparticles, there has been limited research on the assembly of thin films out of perfectly monodisperse nanoclusters. Here, we show a formation of Langmuir films using perfectly monodisperse gold nanoclusters with composition Au32(nBu3P)12Cl8 exhibiting a diameter of 1.8 nm. Using both in situ and ex situ small-angle X-ray scattering, we show that the monolayer formed on a Langmuir-Blodgett trough exhibits long-range order. Moreover, after compressing the monolayer, we found that the stress accumulated prior to the monolayer collapse triggers a transition to a short-range order not previously reported. If such monolayer is compressed further, the second layer is not formed as in the case of standard nanoparticles. Instead, a growth of islands by an odd number of layers is observed, leading to a thin film with a structure consisting of two different orientations of the hexagonal lattice. Such anomalous behavior may have implications for the possibilities of thin-film formation.

A synergistic effect of the ion beam sputtered NiOxhole transport layer and MXene doping on inverted perovskite solar cells.

The synergistic effect of high-quality NiOxhole transport layers (HTLs) deposited by ion beam sputtering on ITO substrates and the Ti3C2TxMXene doping of CH3NH3PbI3(MAPI) perovskite layers is investigated in order to improve the power conversion efficiency (PCE) of p-i-n perovskite solar cells (PSCs). The 18 nm thick NiOxlayers are pinhole-free and exhibit large-scale homogeneous surface morphology as revealed by the atomic force microscopy (AFM). The grazing-incidence x-ray diffraction showed a 0.75% expansion of the face-centered cubic lattice, suggesting an excess of oxygen as is typical for non-stoichiometric NiOx. The HTLs were used to fabricate the PSCs with MXene-doped MAPI layers. A PSC with undoped MAPI layer served as a control. The size of MAPI polycrystalline grains increased from 430 ± 80 nm to 620 ± 190 nm on the doping, as revealed by AFM. The 0.15 wt% MXene doping showed a 14.3% enhancement in PCE as compared to the PSC with undoped MAPI. The energy-resolved electrochemical impedance spectroscopy revealed one order of magnitude higher density of defect states in the band gap of MXene-doped MAPI layer, which eliminated beneficial effect of reduced total area of larger MAPI grain boundaries, decreasing short-circuit current. The PCE improvement is attributed to a decrease of the work function from -5.26 eV to -5.32 eV on the MXene doping, which increased open-circuit voltage and fill factor.

Langmuir-Scheaffer Technique as a Method for Controlled Alignment of 1D Materials.

A widely applicable method for aligning 1D materials, and in particular carbon nanotubes (CNTs), independent of their preparation would be very useful as the growth methods for these materials are substance-specific. Langmuir-Schaefer (LS) deposition could be such an approach for alignment, as it aligns a large number of 1D materials independently of the desired substrate. However, the mechanism and required conditions for alignment of 1D nanomaterials in a Langmuir trough are still unclear. Here we show, relying on numerical simulations of the Langmuir film compression, that the LS method is a powerful tool to achieve maximal alignment of 1D material in a controllable manner. In particular, 1D materials terminated with a suitable surfactant can align only if the velocity induced by the attraction between individual 1D entities is low enough relative to the flow speed. To validate this model, we achieved an efficient LS alignment of single-walled carbon nanotubes covered with a suitable surfactant relying on the numerical simulations. In situ polarized Raman microspectroscopy during the compression of Langmuir film revealed good quantitative agreement between the numerical simulations and the experiment. This suggests the applicability of the LS technique as a versatile method for the controlled alignment of 1D materials.

Surface-Controlled Crystal Alignment of Naphthyl End-Capped Oligothiophene on Graphene: Thin-Film Growth Studied by in Situ X-ray Diffraction.

We report on the microstructure, morphology, and growth of 5,5'-bis(naphth-2-yl)-2,2'-bithiophene (NaT2) thin films deposited on graphene, characterized by grazing incidence X-ray diffraction (GIXRD) and complemented by atomic force microscopy (AFM) measurements. NaT2 is deposited on two types of graphene surfaces: custom-made samples where chemical vapor deposition (CVD)-grown graphene layers are transferred onto a Si/SiO2 substrate by us and common commercially transferred CVD graphene on Si/SiO2. Pristine Si/SiO2 substrates are used as a reference. The NaT2 crystal structure and orientation depend strongly on the underlying surface, with the molecules predominantly lying down on the graphene surface (face-on orientation) and standing nearly out-of-plane (edge-on orientation) on the Si/SiO2 reference surface. Post growth GIXRD and AFM measurements reveal that the crystalline structure and grain morphology differ depending on whether there is polymer residue left on the graphene surface. In situ GIXRD measurements show that the thickness dependence of the intensity of the (111) reflection from the crystalline edge-on phase does not intersect zero at the beginning of the deposition process, suggesting that an initial wetting layer, corresponding to 1-2 molecular layers, is formed at the surface-film interface. By contrast, the (111) reflection intensity from the crystalline face-on phase grows at a constant rate as a function of film thickness during the entire deposition.

On the extraction of MoO x photothermally active nanoparticles by gel filtration from a byproduct of few-layer MoS2 exfoliation.

Gel filtration is a versatile technique employed for biological molecules and nanoparticles, offering their reproducible classification based on size and shape. Colloidal nanoparticles are of significant interest in biomedical applications due to a large number of solution-based bioconjugation procedures. Nevertheless, the inherent polydispersity of the nanoparticles produced by various techniques necessitates the employment of high yield separation and purification techniques. Here we demonstrate the employment of gel filtration on non-stoichiometric plasmonic MoO x nanoparticles, prepared by an oxidation process during liquid-phase exfoliation of few-layer MoS2 nanosheets. This resulted in the separation of two types of MoO x particles, in the form of two different chromatographic fractions. They showed different sizes, morphological and optical properties. The fraction containing smaller particles with diameters of 1-4 nm, exhibited an increased absorbance peak in the near IR region and responded with a significant temperature increase to laser irradiation at the wavelength close to the maximal absorption. The fraction with the larger particles from 3 up to 10 nm, showed weak photoluminescence and a preferred orientation upon the deposition on a planar substrate. However, it had no absorbance in the near IR compared to the former fraction. According to our knowledge, this is the first time that the gel filtration was applied to the separation of molybdenum oxide nanomaterials. This step ensured the isolation of plasmonic MoO x nanoparticles suitable for further bioconjugation and target photothermal treatment.

Reorientation of π-conjugated molecules on few-layer MoS2 films.

Small π-conjugated organic molecules have attracted substantial attention in the past decade as they are considered as candidates for future organic-based (opto-)electronic applications. The molecular arrangement in the organic layer is one of the crucial parameters that determine the efficiency of a given device. The desired orientation of the molecules is achieved by a proper choice of the underlying substrate and growth conditions. Typically, one underlying material supports only one inherent molecular orientation at its interface. Here, we report on two different orientations of diindenoperylene (DIP) molecules on the same underlayer, i.e. on a few-layer MoS2 substrate. We show that DIP molecules adopt a lying-down orientation when deposited on few-layer MoS2 with horizontally oriented layers. In contrast, for vertically aligned MoS2 layers, DIP molecules are arranged in a standing-up manner. Employing in situ and real-time grazing-incidence wide-angle X-ray scattering (GIWAXS), we monitored the stress evolution within the thin DIP layer from the early stages of the growth, revealing different substrate-induced phases for the two molecular orientations. Our study opens up new possibilities for the next-generation of flexible electronics, which might benefit from the combination of MoS2 layers with unique optical and electronic properties and an extensive reservoir of small organic molecules.

Molecular targeting of bioconjugated graphene oxide nanocarriers revealed at a cellular level using label-free Raman imaging.

Two-dimensional materials as graphene oxide (GO) are able to accommodate labels as well as toxins for diagnostics and therapy, respectively. The transmembrane protein carbonic anhydrase (CA IX) is one of the molecules selectively expressed by tumor cells. Here, we demonstrate bioconjugation of GO to biotinylated M75 antibody highly selective towards CA IX. Based on a model system, binding between the bioconjugated GO-M75 and Madin-Darby Canine Kidney (MDCK) cells was evaluated. As proven by fluorescence-activated cell sorting, higher intake was observed for GO-M75 towards MDCK cells ectopically expressing CA IX protein on their surface when compared to control MDCK. In particular, we were able to localize GO nanocarrier crossing the membrane during endocytosis, thanks to the optical cross-sectioning of living cells in real-time employed the label-free confocal Raman microscopy. The increased affinity of the prepared GO-M75 molecular complexes validates the use of two-dimensional materials for future strategies of targeted cancer treatment.

Tailored Langmuir-Schaefer Deposition of Few-Layer MoS2 Nanosheet Films for Electronic Applications.

Few-layer MoS2 films stay at the forefront of current research of two-dimensional materials. At present, continuous MoS2 films are prepared by chemical vapor deposition (CVD) techniques. Herein, we present a cost-effective fabrication of the large-area spatially uniform films of few-layer MoS2 flakes using a modified Langmuir-Schaefer technique. The compression of the liquid-phase exfoliated MoS2 flakes on the water subphase was used to form a continuous layer, which was subsequently transferred onto a submerged substrate by removing the subphase. After vacuum annealing, the electrical sheet resistance dropped to a level of 10 kΩ/sq, being highly competitive with that of CVD-deposited MoS2 nanosheet films. In addition, a consistent fabrication protocol of the large-area conductive MoS2 films was established. The morphology and electrical properties predetermine these films to advanced detecting, sensing, and catalytic applications. A large number of experimental techniques were used to characterize the exfoliated few-layer MoS2 flakes and to elucidate the formation of the few-layer MoS2 Langmuir film.

Tailoring the interparticle distance in Langmuir nanoparticle films.

The ability to control the interparticle distance in self-assembled arrays of nanoparticles plays an important role in a large number of applications, which require tunable electronic and photonic properties. Importantly, practical applications in real devices rely on arrays satisfying more stringent requirements of lateral homogeneity controlled over a large scale. Herein, the interparticle distance in ordered nanoparticle assemblies was controlled by varying the nanoparticle effective size via the molecular chemical nature and chain length of the ligand. Iron oxide nanoparticles (IONPs) were functionalized by three types of ligands, namely (i) a mixture of oleic acid/oleylamine (OA/OAm), (ii) poly(n-butyl acrylate) (PBA) and (iii) polystyrene (PS), while two different molar masses of PBA and PS were used. The polymeric ligands with narrow dispersity and bearing phosphonic chain-end groups were prepared by atom transfer radical polymerization. Functionalization of the IONPs with polymeric ligands was achieved using a ligand exchange method. Both the hydrodynamic diameter and size distribution of the nanoparticles in colloidal solution were determined by dynamic light scattering (DLS). The mean interparticle distances in Langmuir-Schaefer monolayers prepared on solid substrates were assessed by means of the pair correlation function calculated from the atomic force microscopy (AFM) images. Furthermore, the lateral ordering, homogeneity, and interparticle distances averaged over a mesoscopic scale of the ordered monolayers were studied by the grazing-incidence small-angle X-ray scattering (GISAXS) technique. We demonstrate that the (nanoparticle) centre-to-centre distance in the ordered assemblies constituted by the IONPs with the core diameter of about 6 nm can be varied from 7.6 to about 12 nm with the resulting interparticle gap change by a factor of about 4.

An elevated concentration of MoS2 lowers the efficacy of liquid-phase exfoliation and triggers the production of MoOx nanoparticles.

It is generally accepted that liquid-phase exfoliation (LPE) enables large-scale production of few-layer MoS2 flakes. In our work, we studied in detail few-layer MoS2 oxidation in the course of standard LPE in a water/ethanol solution. We demonstrate that an increase of the initial MoS2 concentration above a certain threshold triggers a pronounced oxidation and the exfoliation process starts to produce MoOx nanoparticles. A subsequent decrease of the water pH along with an increased content of SO42- suggests an oxidation scenario of few-layer MoS2 oxidation towards MoOx nanoparticles. Moreover, the lowered pH leads to agglomeration and sedimentation of the few-layer MoS2 flakes, which significantly lowers their production yield. We employed a large number of physico-chemical techniques to study the MoS2-to-MoOx transformation and found a threshold value of 10 mg ml-1 of the initial MoS2 concentration to trigger this transformation.

Label-free tracking of nanosized graphene oxide cellular uptake by confocal Raman microscopy.

Graphene oxide (GO), a partially oxidized two-dimensional allotrope of carbon, is an attractive nanocarrier for cancer diagnostics and therapy. The nanometer-sized GO is known to permeate cell membranes. Herein we studied the cellular uptake pathways of GO nanoflakes by cancer and non-cancerous cell lines. By employing confocal Raman imaging, we were able to track the GO cellular uptake in living cells (C33 and MDCK) without any additional fluorescent or plasmonic labels. This specific progress in label-free Raman imaging of GO facilitates the monitoring of nanoflakes at the cellular level.

Fast low-temperature plasma reduction of monolayer graphene oxide at atmospheric pressure.

We report on an ultrafast plasma-based graphene oxide reduction method superior to conventional vacuum thermal annealing and/or chemical reduction. The method is based on the effect of non-equilibrium atmospheric-pressure plasma generated by the diffuse coplanar surface barrier discharge in proximity of the graphene oxide layer. As the reduction time is in the order of seconds, the presented method is applicable to the large-scale production of reduced graphene oxide layers. The short reduction times are achieved by the high-volume power density of plasma, which is of the order of 100 W cm-3. Monolayers of graphene oxide on silicon substrate were prepared by a modified Langmuir-Schaefer method and the efficient and rapid reduction by methane and/or hydrogen plasma was demonstrated. The best results were obtained for the graphene oxide reduction in hydrogen plasma, as verified by x-ray photoelectron spectroscopy and Raman spectroscopy.

Evaluation of low-cadmium ZnCdSeS alloyed quantum dots for remote phosphor solid-state lighting technology.

We report on the possibility to enhance color rendering of commercially available remote phosphor light-emitting diode modules by using low-cadmium content ZnCdSeS alloyed quantum dots. The employed numerical simulations showed that the color-rendering index of 90+ at the color-correlated temperature of 3200 K can be achieved by application of a single layer of quantum dots onto a neutral-white remote phosphor substrate. The experimental results fully support the numerical calculations, thus revealing the only limiting factor in achieving a higher photometric performance: the self-absorption effect in quantum dots. The presented low-cadmium content quantum dots allow a price-effective upgrade of already existing remote phosphor solid-state lighting technology toward a higher color-rendering capability.

Above room temperature spin crossover in mononuclear iron(II) complexes featuring pyridyl-benzimidazole bidentate ligands adorned with aliphatic chains.

Two bidentate ligands (L1 = 1-pentyl-2-(pyridin-2-yl)-1H-benzimidazole and L2 = 1-heptyl-2-(pyridin-2-yl)-1H-benzimidazole) were employed for the synthesis of five mononuclear Fe(II) coordination compounds 1-5 containing perchlorate, tetrafluoroborate and triflate counterions. Single-crystal X-ray diffraction analysis confirmed the expected molecular structures of all the reported compounds, revealing a moderately distorted octahedral geometry of {FeN6} coordination chromophores. All five compounds exhibit thermal spin crossover with T1/2 temperatures allocated above 400 K. The theoretical calculations supported the experimental magnetic investigation and helped to explain the electronic structures of the reported complexes with respect to the occurrence of thermal spin state switching. In addition, compound 4 was employed for the preparation of Langmuir-Blodgett films and fabrication of molecular films using the method of spontaneous evaporation of the subphase. While the formation of Langmuir-Blodgett films was unsuccessful due to the instability of the compound at the water/air interface, the latter technique allowed the formation of molecular films of 4 with well-defined thickness and homogeneity.

Evolution of Defects, Morphology, and Strain during FAMAPbI3 Perovskite Vacuum Deposition: Insights from In Situ Photoluminescence and X-ray Scattering.

At present, the power conversion efficiency of single-junction perovskite-based solar cells reaches over 26%. The further efficiency increase of perovskite-based optoelectronic devices is limited mainly by defects, causing the nonradiative recombination of charge carriers. To improve efficiency and ensure reproducible fabrication of high-quality layers, it is crucial to understand the perovskite nucleation and growth mechanism along with associated process control to reduce the defect density. In this study, we investigate the growth kinetics of a promising narrow bandgap perovskite, formamidinium methylammonium lead iodide (FAMAPbI3), for high-performance single-junction solar cells. The temporal evolution of structural and optoelectronic properties during FAMAPbI3 vacuum codeposition was inspected in real time by grazing-incidence wide-angle X-ray scattering and photoluminescence. Such a combination of analytical techniques unravels the evolution of intrinsic defect density and layer morphology correlated with lattice strain from the early stages of the perovskite deposition.

SERS Performance of Ti3C2Tx MXene-Based Substrates Correlates with Surface Morphology.

The surface-enhanced Raman scattering (SERS) properties of low-dimensional semiconducting MXene nanoflakes have been investigated over the last decade. Despite this fact, the relationship between the surface characteristics and SERSing performance of a MXene layer has yet to be comprehensively investigated and elucidated. This work shows the importance of surface morphology on the overall SERS effect by studying few-layer Ti3C2Tx MXene-based SERS substrates fabricated by vacuum-assisted filtration (VAF) and spray coating on filter paper. The VAF deposition results in a dense MXene layer suitable for SERS with high spot-to-spot and substrate-to-substrate reproducibility, with a significant limit of detection (LoD) of 20 nM for Rhodamine B analyte. The spray-coated MXenes film revealed lower uniformity, with a LoD of 50 nM for drop-casted analytes. Moreover, we concluded that the distribution of the analyte deposited onto the MXene layer is affected by the presence of MXene aggregates created during the deposition of the MXene layer. Accumulation of the analyte molecules in the vicinity of MXene aggregates was observed for drop-casted deposition of the analyte, which affects the resulting SERS enhancement. Ti3C2Tx MXene layers deposited on filter paper by VAF offer great potential as a cost-effective, easy-to-manufacture, yet robust, platform for sensing applications.

Tunable Subnanometer Gaps in Self-Assembled Monolayer Gold Nanoparticle Superlattices Enabling Strong Plasmonic Field Confinement.

Nanoparticle superlattices produced with controllable interparticle gap distances down to the subnanometer range are of superior significance for applications in electronic and plasmonic devices as well as in optical metasurfaces. In this work, a method to fabricate large-area (∼1 cm2) gold nanoparticle (GNP) superlattices with a typical size of single domains at several micrometers and high-density nanogaps of tunable distances (from 2.3 to 0.1 nm) as well as variable constituents (from organothiols to inorganic S2-) is demonstrated. Our approach is based on the combination of interfacial nanoparticle self-assembly, subphase exchange, and free-floating ligand exchange. Electrical transport measurements on our GNP superlattices reveal variations in the nanogap conductance of more than 6 orders of magnitude. Meanwhile, nanoscopic modifications in the surface potential landscape of active GNP devices have been observed following engineered nanogaps. In situ optical reflectance measurements during free-floating ligand exchange show a gradual enhancement of plasmonic capacitive coupling with a diminishing average interparticle gap distance down to 0.1 nm, as continuously red-shifted localized surface plasmon resonances with increasing intensity have been observed. Optical metasurfaces consisting of such GNP superlattices exhibit tunable effective refractive index over a broad wavelength range. Maximal real part of the effective refractive index, nmax, reaching 5.4 is obtained as a result of the extreme field confinement in the high-density subnanometer plasmonic gaps.