Performances and Biosensing Mechanisms of Interdigitated Capacitive Sensors Based on the Hetero-mixture of SnO2 and In2O3.

This study aims to discuss the synthesis and fabrication of SnO2-In2O3-based thick-films and their biosensing applications. The structural characterization of SnO2-In2O3 nanocomposites was performed using X-ray diffraction, Raman spectroscopy and transmission electron microscopy. Furthermore, the screen-printing technology was used in the fabrication of conductive electrodes to form an interdigitated capacitive structure, and the sensor layer based on the mixture of SnO2 and In2O3. Moreover, the sensing performance of the developed structure was tested using Pseudomonas aeruginosa (P. aeruginosa) and Staphylococcus aureus (S. aureus) bacteria. In addition, the validation of sensing characteristics was performed by electrochemical impedance spectroscopic and self-resonant frequency analysis. Finally, the sensing properties were analyzed for two consecutive days, and changes in both P. aeruginosa and S. aureus pathogens growing media were also studied.

A Wireless LC Sensor Coated with Ba0.9Bi0.066TiO3 for Measuring Temperature.

This paper presents a passive LC wireless sensor for measuring temperature. The sensor is designed as a parallel connection of a spiral inductor and an interdigitated capacitor and it was fabricated in a conductive layer using LTCC (Low Temperature Co-fired Ceramic) technology. The inderdigitated capacitor electrodes were coated with a thin film of bismuth doped barium titanate (Ba0.9Bi0.066TiO3), whose permittivity changes with temperature, which directly induces changes in the capacitance of the interdigitated capacitor and consequently changes the resonant frequency of the sensor. The measurements of S-parameter of the sensor were performed using a Vector Network Analyzer (E5071B, Agilent Technologies, Santa Clara, CA, USA), whose port was connected to the antenna coil that was placed around the sensor in order to be able to wirelessly detect temperature, in the temperature range from 25 °C to 165 °C.

Comprehensive Study of the Chemistry behind the Stability of Carboxylic SWCNT Dispersions in the Development of a Transparent Electrode.

Single-walled carbon nanotubes (SWCNTs) are well-known for their excellent electrical conductivity. One promising application for SWCNT-based thin films is as transparent electrodes for uncooled mid-IR detectors (MIR). In this paper, a combination of computational and experimental studies were performed to understand the chemistry behind the stability of carboxylic SWCNTs (SWCNTs-COOH) dispersions in different solvents. A computational study based on the density functional tight-binding (DFTB) method was applied to understand the interactions of COOH-functionalized carbon nanotubes with selected solvents. Attention was focused on understanding how the protonation of COOH groups influences the binding energies between SWCNTs and different solvents. Thin film electrodes were prepared by alternately depositing PEI and SWCNT-COOH on soda lime glass substrates. To prepare a stable SWCNT dispersion, different solvents were tested, such as deionized (DI) water, ethanol and acetone. The SWCNT-COOH dispersion stability was tested in different solvents. Samples were prepared to study the relationship between the number of depositions, transparency in the MIR range (2.5-5 µm) and conductivity, looking for the optimal thickness that would satisfy the application. The MIR transparency of the electrode was reduced by 20% for the thickest SWCNT layers, whereas sheet resistance values were reduced to 150-200 kΩ/sq.

Structure and dielectric properties of (1-x)Bi0.5Na0.5TiO3-xBaTiO3 piezoceramics prepared using hydrothermally synthesized powders.

The influence of different processing parameters and various Ba2+ addition (up to 10 mol%) on the structure and dielectric properties of Bi0.5Na0.5TiO3-BaTiO3 (BNT-BT) ceramics was investigated. The powders were hydrothermally synthesized in the alkaline environment at 180°C for different time periods. X-ray diffraction confirmed the presence of dominant rhombohedral Bi0.5Na0.5TiO3 phase and a small amount of secondary pyrochlore Bi2Ti2O7 phase in the pure BNT powders. In addition, one-dimensional Na2Ti2O7 structure was also observed in the powder hydrothermally treated for a long time (i.e. 48 h). The amount of secondary pyrochlore phase in the BNT-BT powders increases with the increase of Ba2+ content. The synthesized powders were pressed into pellets and finally sintered at various temperatures up to 1150°C. High density (more than 90%TD) was obtained in all BNT-BT sintered samples. Optimal sintering parameters were chosen in order to obtain dense ceramics with the optimal phase composition. The temperature dependence of dielectric properties for the BNT-BT ceramics was also studied. Relaxor behaviour of BNT-based ceramics and broad transition peaks are evident in all samples. Dielectric constant up to 400 as well as an acceptable low dielectric loss at temperatures lower than 200°C were obtained in BNT-BT ceramics.

Chemical vapor synthesis of nanocrystalline perovskites using laser flash evaporation of low volatility solid precursors.

One key requirement for the production of multinary oxide films by chemical vapor deposition (CVD) or nanocrystalline multinary oxides particles by chemical vapor synthesis (CVS) is the availability of precursors with high vapor pressure. This is especially the case for CVS where much higher production rates are required compared to thin films prepared by CVD. However, elements, which form low valent cations such as alkaline earth metals, are typically only available as solid precursors of low volatility, e.g., in form of beta-diketonates. This study describes laser flash evaporation as precursor delivery method for CVS of nanocrystalline perovskites. Laser flash evaporation exploits the nonequilibrium evaporation of solid metal organic precursors of low vapor pressure by absorption of the infrared radiation of a CO(2) laser. It is shown that stoichiometric, nanocrystalline particles consisting of SrZrO(3) and SrTiO(3) can be formed from corresponding mixtures of beta-diketonates which are evaporated nonselectively and with high rates by laser flash evaporation.