Grafting of Amine End-Functionalized Side-Chain Polybenzimidazole Acid-Base Membrane with Enhanced Phosphoric Acid Retention Ability for High-Temperature Proton Exchange Membrane Fuel Cells.

A high phosphoric acid uptake and retention capacity are crucial for the high performance and stable operation of phosphoric acid/polybenzimidazole (PA/PBI)-based high-temperature proton exchange membranes. In this work, amine end-functionalized side-chain grafted PBI (AGPBI) with different grafting degrees are synthesized to enhance both the phosphoric acid uptake and the acid retention ability of the accordingly formed membranes. The optimized acid-base membrane exhibits a PA uptake of 374.4% and an anhydrous proton conductivity of 0.067 S cm-1 at 160 °C, with the remaining proton conductivity percentages of 91.0% after a 100 h stability test. The accordingly fabricated membrane electrode assembly deliver peak power densities of 0.407 and 0.638 W cm-2 under backpressure of 0 and 200 kPa, which are significantly higher than 0.305 and 0.477 W cm-2 for the phosphoric acid-doped unmodified PBI membrane under the same conditions.

Surface Acidity Dictates Proton Transport in WO3/ZrO2: Proton-Conductive Behavior and Mechanistic Insight.

Development of inorganic proton conductors that are applicable in a wide temperature range is crucial for applications such as fuel cells. Most of the reported proton conductors suffer from limited proton conductivity, especially at low temperature. In addition, the mechanism of proton conduction in the conductors is not fully understood, which limits the rational design of advanced proton conductors. In this work, we report the use of metal oxide solid acid as a promising proton conductor. WO3/ZrO2 (WZ) with different surface acidities is synthesized by controlling the content of WO3 on the surface of ZrO2. It is demonstrated that proton conductivity of WZ samples is closely related with their acidity. WZ with the strongest acidity exhibits the highest proton conduction performance at low temperatures, with a proton conductivity of 3.27 × 10-5 S cm-1 at 14 °C. The excellent performance of the WZ-type proton conductor is clarified with theoretical calculations. The results show that the enhanced water adsorption and the lowered activation barrier for breakage of the O-H bond in surface-adsorbed water are the key to the excellent proton-conductive performance of WZ. The experimental results and mechanistic insights gained in this work suggest that WZ is a promising proton conductor, and tailoring the surface acidity of metal oxides is an effective approach to regulate their proton-conductive performance.

Pt Atomic Layers with Tensile Strain and Rich Defects Boost Ethanol Electrooxidation.

Surface and strain engineering are two effective strategies to improve performance; however, synergetic controls of surface and strain effects remains a grand challenge. Herein, we report a highly efficient and stable electrocatalyst with defect-rich Pt atomic layers coating an ordered Pt3Sn intermetallic core. Pt atomic layers enable the generation of 4.4% tensile strain along the [001] direction. Benefiting from synergetic controls of surface and strain engineering, Pt atomic-layer catalyst (Ptatomic-layer) achieves a remarkable enhancement on ethanol electrooxidation performance with excellent specific activity of 5.83 mA cm-2 and mass activity of 1166.6 mA mg Pt-1, which is 10.6 and 3.6 times higher than the commercial Pt/C, respectively. Moreover, the intermetallic core endows Ptatomic-layer with outstanding durability. In situ infrared reflection-absorption spectroscopy as well as density functional theory calculations reveal that tensile strain and rich defects of Ptatomci-layer facilitate to break C-C bond for complete ethanol oxidation for enhanced performance.

Polyolefin-Based Separator with Interfacial Chemistry Regulation for Robust Potassium Metal Batteries.

Potassium metal batteries (KMBs) are ideal choices for high energy density storage system owing to the low electrochemical potential and low cost of K. However, the practical KMB applications suffer from intrinsically active K anode, which would bring serious safety concerns due to easier generation of dendrites. Herein, to explore a facile approach to tackle this issue, we propose to regulate K plating/stripping via interfacial chemistry engineering of commercial polyolefin-based separator using multiple functional units integrated in tailored metal organic framework. As a case study, the functional units of MIL-101(Cr) offer high elastic modulus, facilitate the dissociation of potassium salt, improve the K+ transfer number and homogenize the K+ flux at the electrode/electrolyte interface. Benefiting from these favorable features, uniform and stable K plating/stripping is realized with the regulated separator. Full battery assembled with the regulated separator showed ∼19.9 % higher discharge capacity than that with glass fiber separator at 20 mA g-1 and much better cycling stability at high rates. The generality of our approach is validated with KMBs using different cathodes and electrolytes. We envision that the strategy to suppress dendrite formation by commercial separator surface engineering using tailor-designed functional units can be extended to other metal/metal ion batteries.

Fe-Incorporated Ni/MoO2 Hollow Heterostructure Nanorod Arrays for High-Efficiency Overall Water Splitting in Alkaline and Seawater Media.

Developing high-efficiency and cost-effective bifunctional catalysts for water electrolysis is fascinating but still remains challenging. Thus, diverse strategies have been utilized to boost the activity toward oxygen/hydrogen evolution reactions (OER/HER) for water splitting. Among them, composition and structure engineering as an effective strategy has received extensive attention. Here, by means of a self-sacrificing template strategy and simultaneous regulation of the composition and structure, Fe-incorporated Ni/MoO2 heterostructural (NiFe/Fe-MoO2 ) hollow nanorod arrays are designed and constructed. Benefiting from abundant catalytic active sites, high intrinsic activity, and fast reaction kinetics, NiFe/Fe-MoO2 exhibits superior OER (η20  = 213 and 219 mV) and Pt-like HER activity (η10  = 34 and 38 mV), respectively, in 1 m KOH and alkaline seawater media. This results in attractive prospects in alkaline water and seawater electrolysis with only voltages of 1.48 and 1.51 V, and 1.69 and 1.73 V to achieve current densities of 10 and 100 mA cm-2 , respectively, superior to the Pt/C and RuO2 pair as a benchmark. Undoubtedly, this work provides a beneficial approach to the design and construction of noble-metal-free bifunctional catalysts toward efficient hydrogen production from alkaline water and seawater electrolysis.

A cascade reaction for regioselective construction of pyrazole-containing aliphatic sulfonyl fluorides.

A copper-catalyzed cascade reaction of α-diazocarbonyl compounds with ethenesulfonyl fluoride (ESF) is developed, affording a variety of highly functionalized pyrazolyl aliphatic sulfonyl fluorides in good to excellent yields (66-98%). This transformation features broad substrates, exclusive regioselectivity, high atom economy and operational simplicity, thus providing a straightforward method for the direct construction of pyrazole-containing aliphatic sulfonyl fluorides, which will provide great applicable value in medicinal chemistry and other related disciplines.

PtNi Alloy Coated in Porous Nitrogen-Doped Carbon as Highly Efficient Catalysts for Hydrogen Evolution Reactions.

The development of low platinum loading hydrogen evolution reaction (HER) catalysts with high activity and stability is of great significance to the practical application of hydrogen energy. This paper reports a simple method to synthesize a highly efficient HER catalyst through coating a highly dispersed PtNi alloy on porous nitrogen-doped carbon (MNC) derived from the zeolite imidazolate skeleton. The catalyst is characterized and analyzed by physical characterization methods, such as XRD, SEM, TEM, BET, XPS, and LSV, EIS, it, v-t, etc. The optimized sample exhibits an overpotential of only 26 mV at a current density of 10 mA cm-2, outperforming commercial 20 wt% Pt/C (33 mV). The synthesized catalyst shows a relatively fast HER kinetics as evidenced by the small Tafel slope of 21.5 mV dec-1 due to the small charge transfer resistance, the alloying effect between Pt and Ni, and the interaction between PtNi alloy and carrier.

Tuning the Intrinsic Activity and Electrochemical Surface Area of MoS2 via Tiny Zn Doping: Toward an Efficient Hydrogen Evolution Reaction (HER) Catalyst.

Molybdenum sulfide (MoS2 ) is considered as an alternative material for commercial platinum catalysts for electrocatalytic hydrogen evolution reaction (HER). Improving the apparent HER activity of MoS2 to a level comparable to that of Pt is an essential premise for the commercial use of MoS2 . In this work, a Zn-doping strategy is proposed to enhance the HER performance of MoS2 . It is shown that tiny Zn doping into MoS2 leads to the enhancement of the electrochemical surface area, increases in proportion of HER active 1T phase in the material and formation of catalytic sites of higher intrinsic activity. These benefits result in a high-performance HER electrocatalyst with a low overpotential of 190 mV(@10 mA cm-2 ) and a low Tafel slope of 58 mV dec-1 . The origin for the excellent electrochemical performance of the doped MoS2 is rationalized with both experimental and theoretical investigations.

A general approach to nitrile- and sulfonyl fluoride-substituted cyclopropanes.

Both cis and trans relative configurations of functionalized cyano cyclopropane bearing sulfonyl fluoride moiety were accessed by Corey-Chaykovsky cyclopropanation reactions. This protocol used mild conditions, and obtained good yields with excellent functional group compatibility. Further application of this class of compounds in SuFEx reactions and cyano reductions were also successfully achieved in good yields.

Synergistic Coupling of Ni Nanoparticles with Ni3 C Nanosheets for Highly Efficient Overall Water Splitting.

Exploring earth-abundant bifunctional electrocatalysts with high efficiency for water electrolysis is extremely demanding and challenging. Herein, density functional theory (DFT) predictions reveal that coupling Ni with Ni3 C can not only facilitate the oxygen evolution reaction (OER) kinetics, but also optimize the hydrogen adsorption and water adsorption energies. Experimentally, a facile strategy is designed to in situ fabricate Ni3 C nanosheets on carbon cloth (CC), and simultaneously couple with Ni nanoparticles, resulting in the formation of an integrated heterostructure catalyst (Ni-Ni3 C/CC). Benefiting from the superior intrinsic activity as well as the abundant active sites, the Ni-Ni3 C/CC electrode demonstrates excellent bifunctional electrocatalytic activities toward the OER and hydrogen evolution reaction (HER), which are superior to all the documented Ni3 C-based electrocatalysts in alkaline electrolytes. Specifically, the Ni-Ni3 C/CC catalyst exhibits the low overpotentials of only 299 mV at the current density of 20 mA cm-2 for the OER and 98 mV at 10 mA cm-2 for the HER in 1 m KOH. Furthermore, the bifunctional Ni-Ni3 C/CC catalyst can propel water electrolysis with excellent activity and nearly 100% faradic efficiency. This work highlights an easy approach for designing and constructing advanced nickel carbide-based catalysts with high activity based on the theoretical predictions.

Multifunctional Polypropylene Separator via Cooperative Modification and Its Application in the Lithium-Sulfur Battery.

The continuous shuttling of dissolved polysulfides between the electrodes is the primary cause for the rapid decay of lithium-sulfur batteries. Modulation of the separator-electrolyte interface through separator modification is a promising strategy to inhibit polysulfide shuttling. In this work, we develop a graphene oxide and ferrocene comodified polypropylene separator with multifunctionality at the separator-electrolyte interface. The graphene oxide on the functionalized separator could physically adsorb the polysulfide while the ferrocene component could effectively facilitate the conversion of the adsorbed polysulfide. Due to the combination of these beneficial functionalities, the separator exhibits an excellent battery performance, with a high reversible capacity of 409 mAh g-1 after 500 cycles at 0.2 C. We anticipate that the combinatorial separator functionalization proposed herein is an effective approach for improving the performance of lithium-sulfur batteries.

Three-Dimensional Macroporous Co-Embedded N-Doped Carbon Interweaving with Carbon Nanotubes as Excellent Bifunctional Catalysts for Zn-Air Batteries.

Highly efficient noble metal-free bifunctional catalysts for expediting the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in metal-air batteries or fuel cells are still challenging and imperative. In this work, we report a facile and scalable method for syntheizing three-dimensional (3D) macroporous Co-embedded N-doped carbon interconnecting with in situ growth carbon nanotubes (CNTs). The as-synthesized material exhibits great electrocatalytic performance for ORR with an onset potential of 0.901 V vs RHE as well as a high limited current density of 4.83 mA/cm2 in an alkaline electrolyte under a rotation speed of 1600 rpm at 5 mV/s. Furthermore, this 3D porous carbon also shows good electrocatalytic performance for OER in an alkaline electrolyte. This high electrocatalytic performance is mainly attributed to its large specific surface area and highly conductive CNTs and the synergistic effect between Co-active species and the carbon framework. The result of a two-electrode Zn-air battery based on this carbon material achieves a peak density of 163 mW/cm2 at a voltage of 0.63 V, indicating the great potential of the catalyst for battery application.

Water-Stable Nanoporous Polymer Films with Excellent Proton Conductivity.

Achieving high values for proton conductivity in a material critically depends on providing hopping sites arranged in a regular fashion. Record values reported for regular, molecular crystals cannot yet be reached by technologically relevant systems, and the best values measured for polymer membranes suited for integration into devices are almost two orders of magnitude lower. Here, an alternative polymer membrane synthesis strategy based on the chemical modification of surface-mounted, monolithic, crystalline metal-organic framework thin films is demonstrated. Due to chemical crosslinking and subsequent removal of metal ions, these surface-mounted gels (SURGELs) are found to exhibit high proton conductivity (0.1 S cm-1 at 30 °C and 100% RH (relative humidity). These record values are attributed to the highly ordered polymer network structure containing regularly spaced carboxylic acid side groups. These covalently bound organic frameworks outperform conventional, ion-conductive polymers with regard to ion conductivity and water stability. Pronounced water-induced swelling, which causes severe mechanical instabilities in commercial membranes, is not observed.

Design of N-Coordinated Dual-Metal Sites: A Stable and Active Pt-Free Catalyst for Acidic Oxygen Reduction Reaction.

We develop a host-guest strategy to construct an electrocatalyst with Fe-Co dual sites embedded on N-doped porous carbon and demonstrate its activity for oxygen reduction reaction in acidic electrolyte. Our catalyst exhibits superior oxygen reduction reaction performance, with comparable onset potential (Eonset, 1.06 vs 1.03 V) and half-wave potential (E1/2, 0.863 vs 0.858 V) than commercial Pt/C. The fuel cell test reveals (Fe,Co)/N-C outperforms most reported Pt-free catalysts in H2/O2 and H2/air. In addition, this cathode catalyst with dual metal sites is stable in a long-term operation with 50 000 cycles for electrode measurement and 100 h for H2/air single cell operation. Density functional theory calculations reveal the dual sites is favored for activation of O-O, crucial for four-electron oxygen reduction.

Nanostructure-based proton exchange membrane for fuel cell applications at high temperature.

As a clean and highly efficient energy source, the proton exchange membrane fuel cell (PEMFC) has been considered an ideal alternative to traditional fossil energy sources. Great efforts have been devoted to realizing the commercialization of the PEMFC in the past decade. To eliminate some technical problems that are associated with the low-temperature operation (such as catalyst poisoning and poor water management), PEMFCs are usually operated at elevated temperatures (e.g., > 100 degrees C). However, traditional proton exchange membrane (PEM) shows poor performance at elevated temperature. To achieve a high-performance PEM for high temperature fuel cell applications, novel PEMs, which are based on nanostructures, have been developed recently. In this review, we discuss and summarize the methods for fabricating the nanostructure-based PEMs for PEMFC operated at elevated temperatures and the high temperature performance of these PEMs. We also give an outlook on the rational design and development of the nanostructure-based PEMs.

Structure-Performance Correlation Inspired Platinum-Assisted Anode with a Homogeneous Ionomer Layer for Proton Exchange Membrane Water Electrolysis.

PEMWE is becoming one of the most promising technologies for efficient and green hydrogen production, while the anode OER process is deeply restricted by the now commercially used iridium oxide with sluggish reaction kinetics and super high cost. Deeply exploring the essential relationship between the underlying substrate materials and the performance of PEMWE cells while simultaneously excavating new practical and convenient methods to reduce costs and increase efficiency is full of challenges. Herein, two representative kinds of iridium oxide were studied, and their performance difference in PEMWE was precisely analyzed with electrochemical techniques and physical characterization and further linked to the ionomer/catalyst compound features. A novel anode with a uniform thin ionomer coating was successfully constructed, which simultaneously optimized the ionomer/catalyst aggregates as well as electrical conductivity, resulting in significantly enhanced PEMWE performance. This rigorous qualitative analysis of the structure-performance relationship as well as effective ionomer-affinitive optimization strategies are of great significance to the development of next-generation high-performance PEM water electrolyzers.

On-surface conversion reaction realizes advanced red phosphorus/carbon anode for high-performance lithium-ion batteries.

Red phosphorus (RP), the one of the most prospective anodes in lithium-ion batteries (LIBs), has been severely limited due to the intrinsic defects of massive volume expansion and low electronic conductivity. The vaporization-condensation-conversion (VCC), which confines RP nanoparticles into carbon host, is the most widely used method to address the above drawbacks and prepare RP/C nanostructured composites. However, the volume effect-dominated RP caused by the inevitably deposition of RP vapor on the surface of carbon material suffers from the massive volume change and unstable solid electrolyte interface (SEI) film. Herein, we propose a simple interfacial modification method to eliminate the superficial RP and yield stable surface composed of ion-conducting Li3PS4 solid electrolyte, endowing RP/AC composites excellent cycling performance and ultrafast reaction kinetics. Therefore, the RP/AC@S composites exhibit 926 mAh/g after 320 cycles at 0.2 A/g (running over 181 days), with 81.6 % capacity retention and a corresponding capacity decay rate of as low as 0.059 %. When coupled with LiFePO4 cathode, the full cells present superior cycling performance (62.1 mAh/g after 500 cycles at 1 A/g) and excellent rate capability (81.1 mAh/g at 1.0 A/g).

Optimization of Porous Structures of Carbon Matrices for Loading Red Phosphorus to Achieve High-Capacity and Long-Life Anodes for All-Solid-State Lithium-Ion Batteries.

All-solid-state lithium-ion batteries (ASSLIBs) using sulfide electrolytes and high-capacity alloy-type anodes have attracted sizable interest due to their potential excellent safety and high energy density. Encapsulating insulating red phosphorus (P) inside nanopores of a carbon matrix can adequately activate its electrochemical alloying reaction with lithium. Therefore, the porosity of the carbon matrix plays a crucial role in the electrochemical performance of the resulting red P/carbon composites. Here, we use zeolite-templated carbon (ZTC) with monodisperse micropores and mesoporous carbon (CMK-3) with uniform mesopores as the model hosts of red P. Our results reveal that micropores enable more effective pore utilization for the red P loading, and the P@ZTC material can achieve a record-high content (65.0 wt %) of red P confined within pores. When used as an anode of ASSLIBs, the P@ZTC electrode delivers an ultrahigh capacity of 1823 mA h g-1 and a high initial Coulombic efficiency of 87.44%. After 400 deep discharge-charge cycles (running over 250 days) at 0.2 A g-1, the P@ZTC electrode still holds a reversible capacity of 1260 mA h g-1 (99.92% capacity retention per cycle). Moreover, a P@ZTC||LiNi0.8Co0.1Mn0.1O2 full cell can deliver a reversible areal capacity of over 3 mA h cm-2 at 0.1C after 100 cycles.

Electronic structure optimizing of Ru nanoclusters via Co single atom and N, S co-doped reduced graphene oxide for accelerating water electrolysis.

The development of efficient and stable electrocatalysts for hydrogen evolution reaction (HER) is impending for the advancement of water-splitting. In this study, we developed a novel electrocatalyst consisting of highly dispersed Ru nanoclusters ameliorated by cobalt single atoms and N, S co-doped reduced graphene oxide (CoSARuNC@NSG). Benefitted from the optimized electronic structure of the Ru nanoclusters induced by the adjacent single atomic Co and N, S co-doped RGO support, the electrocatalyst exhibits exceptional HER performance with overpotentials of 15 mV and 74 mV for achieving a current density of 10 mA cm-2 in alkaline and acidic water. The catalyst outperforms most noble metal-based HER electrocatalysts. Furthermore, the electrolyzer assembled with CoSARuNC@NSG and RuO2 demonstrated an overall voltage of 1.56 V at 10 mA cm-2 and an excellent operational stability for over 25 h with almost no attenuation. Theoretical calculations also deduce its high HER activity demonstrated by the smaller reaction energy barrier due to the optimized electronic structure of Ru nanoclusters. This strategy involving the regulation of metal nanoparticles activity through flexible single atom and GO support could provide valuable insights into the design of high-performance and low-cost HER catalysts.

Potassium-Hydrogen Hybrid Ion Alkaline Battery: A New Rechargeable Aqueous Battery Combined a K+ Storage Cathode and an Electrochemical Hydrogen Storage Anode.

A rechargeable aqueous hybrid ion alkaline battery, using a proton and a potassium ion as charge carriers for the anode and cathode, respectively, is proposed in this study by using well-developed potassium nickel hexacyanoferrate as the cathode material and mesoporous carbon sheets as the anode material, respectively. The constructed battery operates in a concentrated KOH solution, in which the energy storage mechanism for potassium nickel hexacyanoferrate involves the redox reaction of Fe2+/Fe3+ associated with potassium ion insertion/extraction and the redox reaction of Ni(OH)2/NiOOH. The mechanism for the carbon anode is electrochemical hydrogen storage. The cathode made of potassium nickel hexacyanoferrate exhibits both an ultrahigh capacity of 232.7 mAh g-1 under 100 mA g-1 and a consistent performance of 214 mAh g-1 at 2000 mA g-1 (with a capacity retention of 92.8% after 200 cycles). The mesoporous carbon sheet anode exhibits a capacity of 87.6 mAh·g-1 at 100 mA g-1 with a good rate and cyclic performance. The full cell provides an operational voltage of 1.55 V, a capacity of 93.6 mAh g-1 at 100 mA g-1, and 82.4% capacity retention after 1000 cycles at 2000 mA g-1 along with a low self-discharge rate. The investigation and discussion about the energy storage mechanisms for both electrode materials are also provided.