Bioinspired and Bioderived Aqueous Electrocatalysis.

The development of efficient and sustainable electrochemical systems able to provide clean-energy fuels and chemicals is one of the main current challenges of materials science and engineering. Over the last decades, significant advances have been made in the development of robust electrocatalysts for different reactions, with fundamental insights from both computational and experimental work. Some of the most promising systems in the literature are based on expensive and scarce platinum-group metals; however, natural enzymes show the highest per-site catalytic activities, while their active sites are based exclusively on earth-abundant metals. Additionally, natural biomass provides a valuable feedstock for producing advanced carbonaceous materials with porous hierarchical structures. Utilizing resources and design inspiration from nature can help create more sustainable and cost-effective strategies for manufacturing cost-effective, sustainable, and robust electrochemical materials and devices. This review spans from materials to device engineering; we initially discuss the design of carbon-based materials with bioinspired features (such as enzyme active sites), the utilization of biomass resources to construct tailored carbon materials, and their activity in aqueous electrocatalysis for water splitting, oxygen reduction, and CO2 reduction. We then delve in the applicability of bioinspired features in electrochemical devices, such as the engineering of bioinspired mass transport and electrode interfaces. Finally, we address remaining challenges, such as the stability of bioinspired active sites or the activity of metal-free carbon materials, and discuss new potential research directions that can open the gates to the implementation of bioinspired sustainable materials in electrochemical devices.

Ultrafast synthesis of hard carbon anodes for sodium-ion batteries.

Hard carbons (HCs) are a significantly promising anode material for alkali metal-ion batteries. However, long calcination time and much energy consumption are required for the traditional fabrication way, resulting in an obstacle for high-throughput synthesis and structure regulation of HCs. Herein, we report an emerging sintering method to rapidly fabricate HCs from different carbon precursors at an ultrafast heating rate (300 to 500 °C min-1) under one minute by a multifield-regulated spark plasma sintering (SPS) technology. HCs prepared via the SPS possess significantly fewer defects, lower porosity, and less oxygen content than those pyrolyzed in traditional sintering ways. The molecular dynamics simulations are employed to elucidate the mechanism of the remarkably accelerated pyrolysis from the quickly increased carbon sp2 content under the multifield effect. As a proof of concept, the SPS-derived HC exhibits an improved initial Coulombic efficiency (88.9%), a larger reversible capacity (299.4 mAh⋅g-1), and remarkably enhanced rate capacities (136.6 mAh⋅g-1 at 5 A⋅g-1) than anode materials derived from a traditional route for Na-ion batteries.

Rational Design of Enzymatic Electrodes: Impact of Carbon Nanomaterial Types on the Electrode Performance.

This research focuses on the rational design of porous enzymatic electrodes, using horseradish peroxidase (HRP) as a model biocatalyst. Our goal was to identify the main obstacles to maximizing biocatalyst utilization within complex porous structures and to assess the impact of various carbon nanomaterials on electrode performance. We evaluated as-synthesized carbon nanomaterials, such as Carbon Aerogel, Coral Carbon, and Carbon Hollow Spheres, against the commercially available Vulcan XC72 carbon nanomaterial. The 3D electrodes were constructed using gelatin as a binder, which was cross-linked with glutaraldehyde. The bioelectrodes were characterized electrochemically in the absence and presence of 3 mM of hydrogen peroxide. The capacitive behavior observed was in accordance with the BET surface area of the materials under study. The catalytic activity towards hydrogen peroxide reduction was partially linked to the capacitive behavior trend in the absence of hydrogen peroxide. Notably, the Coral Carbon electrode demonstrated large capacitive currents but low catalytic currents, an exception to the observed trend. Microscopic analysis of the electrodes indicated suboptimal gelatin distribution in the Coral Carbon electrode. This study also highlighted the challenges in transferring the preparation procedure from one carbon nanomaterial to another, emphasizing the importance of binder quantity, which appears to depend on particle size and quantity and warrants further studies. Under conditions of the present study, Vulcan XC72 with a catalytic current of ca. 300 µA cm-2 in the presence of 3 mM of hydrogen peroxide was found to be the most optimal biocatalyst support.

Single-Atom Iridium on Hematite Photoanodes for Solar Water Splitting: Catalyst or Spectator?

Single-atom catalysts (SACs) on hematite photoanodes are efficient cocatalysts to boost photoelectrochemical performance. They feature high atom utilization, remarkable activity, and distinct active sites. However, the specific role of SACs on hematite photoanodes is not fully understood yet: Do SACs behave as a catalytic site or as a spectator? By combining spectroscopic experiments and computer simulations, we demonstrate that single-atom iridium (sIr) catalysts on hematite (α-Fe2O3/sIr) photoanodes act as a true catalyst by trapping holes from hematite and providing active sites for the water oxidation reaction. In situ transient absorption spectroscopy showed a reduced number of holes and shortened hole lifetime in the presence of sIr. This was particularly evident on the second timescale, indicative of fast hole transfer and depletion toward water oxidation. Intensity-modulated photocurrent spectroscopy evidenced a faster hole transfer at the α-Fe2O3/sIr/electrolyte interface compared to that at bare α-Fe2O3. Density functional theory calculations revealed the mechanism for water oxidation using sIr as a catalytic center to be the preferred pathway as it displayed a lower onset potential than the Fe sites. X-ray photoelectron spectroscopy demonstrated that sIr introduced a mid-gap of 4d state, key to the fast hole transfer and hole depletion. These combined results provide new insights into the processes controlling solar water oxidation and the role of SACs in enhancing the catalytic performance of semiconductors in photo-assisted reactions.

Pyridine Functionalized Carbon Nanotubes: Unveiling the Role of External Pyridinic Nitrogen Sites for Oxygen Reduction Reaction.

Pyridinic nitrogen has been recognized as the primary active site in nitrogen-doped carbon electrocatalysts for the oxygen reduction reaction (ORR), which is a critical process in many renewable energy devices. However, the preparation of nitrogen-doped carbon catalysts comprised of exclusively pyridinic nitrogen remains challenging, as well as understanding the precise ORR mechanisms on the catalyst. Herein, a novel process is developed using pyridyne reactive intermediates to functionalize carbon nanotubes (CNTs) exclusively with pyridine rings for ORR electrocatalysis. The relationship between the structure and ORR performance of the prepared materials is studied in combination with density functional theory calculations to probe the ORR mechanism on the catalyst. Pyridinic nitrogen can contribute to a more efficient 4-electron reaction pathway, while high level of pyridyne functionalization result in negative structural effects, such as poor electrical conductivity, reduced surface area, and small pore diameters, that suppressed the ORR performance. This study provides insights into pyridine-doped CNTs-functionalized for the first time via pyridyne intermediates-as applied in the ORR and is expected to serve as valuable inspiration in designing high-performance electrocatalysts for energy applications.

Strain induced electrochemical behaviors of ionic liquid electrolytes in an electrochemical double layer capacitor: Insights from molecular dynamics simulations.

Electrochemical Double Layer Capacitors (EDLCs) with ionic liquid electrolytes outperform conventional ones using aqueous and organic electrolytes in energy density and safety. However, understanding the electrochemical behaviors of ionic liquid electrolytes under compressive/tensile strain is essential for the design of flexible EDLCs as well as normal EDLCs, which are subject to external forces during assembly. Despite many experimental studies, the compression/stretching effects on the performance of ionic liquid EDLCs remain inconclusive and controversial. In addition, there is hardly any evidence of prior theoretical work done in this area, which makes the literature on this topic scarce. Herein, for the first time, we developed an atomistic model to study the processes underlying the electrochemical behaviors of ionic liquids in an EDLC under strain. Constant potential non-equilibrium molecular dynamics simulations are conducted for EMIM BF4 placed between two graphene walls as electrodes. Compared to zero strain, low compression of the EDLC resulted in compromised performance as the electrode charge density dropped by 29%, and the performance reduction deteriorated significantly with a further increase in compression. In contrast, stretching is found to enhance the performance by increasing the charge storage in the electrodes by 7%. The performance changes with compression and stretching are due to changes in the double-layer structure. In addition, an increase in the value of the applied potential during the application of strain leads to capacity retention with compression revealed by the newly performed simulations.

Investigating the Role of Surface Roughness and Defects on EC Breakdown, as a Precursor to SEI Formation in Hard Carbon Sodium-Ion Battery Anodes.

Hard carbon (HC) anodes together with ethylene carbonate (EC)-based electrolytes have shown significant promise for high-performing sodium-ion batteries. However, questions remain in relation to the initial contact between the carbon surface and the EC molecules. The surface of the HC anode is complex and can contain both flat pristine carbon surfaces, curvature, nanoscale roughness, and heteroatom defects. Combining density functional theory and experiments, the effect of different carbon surface motifs and defects on EC adsorption are probed, concluding that EC itself does not block any sodium storage sites. Nevertheless, the EC breakdown products do show strong adsorption on the same carbon surface motifs, indicating that the carbon surface defect sites can become occupied by the EC breakdown products, leading to competition between the sodium and EC fragments. Furthermore, it is shown that the EC fragments can react with a carbon vacancy or oxygen defect to give rise to CO2 formation and further oxygen functionalization of the carbon surface. Experimental characterization of two HC materials with different microstructure and defect concentrations further confirms that a significant concentration of oxygen-containing defects and disorder leads to a thicker solid electrolyte interphase, highlighting the significant effect of atomic-scale carbon structure on EC interaction.

Screening Heteroatom Configurations for Reversible Sloping Capacity Promises High-Power Na-Ion Batteries.

Heteroatom doping has been proved to effectively enhance the sloping capacity, nevertheless, the high sloping capacity almost encounters a conflict with the disappointing initial Coulombic efficiency (ICE). Herein, we propose a heteroatom configuration screening strategy by introducing a secondary carbonization process for the phosphate-treated carbons to remove the irreversible heteroatom configurations but with the reversible ones and free radicals remaining, achieving a simultaneity between the high sloping capacity and ICE (≈250 mAh g-1 and 80 %). The Na storage mechanism was also studied based on this "slope-dominated" carbon to reveal the reason for the absence of the plateau. This work could inspire to distinguish and filter the irreversible heteroatom configurations and facilitate the future design of practical "slope-dominated" carbon anodes towards high-power Na-ion batteries.

Correlating Local Structure and Sodium Storage in Hard Carbon Anodes: Insights from Pair Distribution Function Analysis and Solid-State NMR.

Hard carbons are the leading candidate anode materials for sodium-ion batteries. However, the sodium-insertion mechanisms remain under debate. Here, employing a novel analysis of operando and ex situ pair distribution function (PDF) analysis of total scattering data, supplemented by information on the local electronic structure provided by operando 23Na solid-state NMR, we identify the local atomic environments of sodium stored within hard carbon and provide a revised mechanism for sodium storage. The local structure of carbons is well-described by bilayers of curved graphene fragments, with fragment size increasing, and curvature decreasing with increasing pyrolysis temperature. A correlation is observed between the higher-voltage (slope) capacity and the defect concentration inferred from the size and curvature of the fragments. Meanwhile, a larger lower-voltage (plateau) capacity is observed in samples modeled by larger fragment sizes. Operando PDF data on two commercially relevant hard carbons reveal changes at higher-voltages consistent with sodium ions stored close to defective areas of the carbon, with electrons localized in the antibonding π*-orbitals of the carbon. Metallic sodium clusters approximately 13-15 Å in diameter are formed in both carbons at lower voltages, implying that, for these carbons, the lower-voltage capacity is determined by the number of regions suitable for sodium cluster formation, rather than by having microstructures that allow larger clusters to form. Our results reveal that local atomic structure has a definitive role in determining storage capacity, and therefore the effect of synthetic conditions on both the local atomic structure and the microstructure should be considered when engineering hard carbons.

Intercalation chemistry of graphite: alkali metal ions and beyond.

Reversibly intercalating ions into host materials for electrochemical energy storage is the essence of the working principle of rocking-chair type batteries. The most relevant example is the graphite anode for rechargeable Li-ion batteries which has been commercialized in 1991 and still represents the benchmark anode in Li-ion batteries 30 years later. Learning from past lessons on alkali metal intercalation in graphite, recent breakthroughs in sodium and potassium intercalation in graphite have been demonstrated for Na-ion batteries and K-ion batteries. Interestingly, some significant differences proved to exist for the intercalation of Na+ and K+ into graphite compared with the Li+ case. Such different host-guest interactions are unique depending on the host materials and electrolytes, which greatly contribute to a deeper understanding of intercalation-type electrode materials for next generation alkali metal ion batteries. This review summarizes significant advances from both experimental and theoretical calculations with a focus on comparing the intercalation of three alkali metal ions (Li+, Na+, K+) into graphite and aims to clarify the intimate host-guest relationships and the underlying mechanisms. New approaches developed to achieve favorable intercalation coupled with the challenges in this field are also discussed. We also extrapolate alkali metal ion intercalation in graphite to mono-/multi-valent ions in layered electrode materials, which will deepen the understanding of intercalation chemistry and provide guidance to explore new guests and hosts.

Hydrothermal Conversion of Spent Sugar Beets into High-Value Platform Molecules.

The growing importance of bio-based products, combined with the desire to decrease the production of wastes, boosts the necessity to use wastes as raw materials for bio-based products. A waste material with a large potential is spent sugar beets, which are mainly used as animal feeds or fertilizers. After hydrothermal treatment, the produced chars exhibited an H/C ratio of 1.2 and a higher heating value of 22.7 MJ/kg, which were similar to that of subbituminous coal and higher than that of lignite. Moreover, the treatment of 25 g/L of glucose and 22 g/L of fructose by heating up to 160 °C led to a possible application of spent sugar beets for the production of 5-hydroxymethylfurfural. In the present study, the maximum concentration of 5-hydroxymethylfurfural was 3.4 g/L after heating up to 200 °C.

Surface Interactions during the Removal of Emerging Contaminants by Hydrochar-Based Adsorbents.

The aim of this work was to test activated carbons derived from hydrochars produced from sunflower stem, olive stone and walnut shells, as adsorbents for emerging contaminants in aqueous solution, namely fluoxetine and nicotinic acid. The adsorption capacity was determined by the chemical nature of the adsorbents, namely the presence of specific functional groups and their positive or negative ionization in aqueous solutions and also by steric factors. The activated carbons produced by air showed a higher adsorption capacity of fluoxetine, whilst the samples produced by carbon dioxide activation were more useful to remove nicotinic acid. In general, surface acidity was advantageous for fluoxetine adsorption and detrimental for nicotinic acid removal. The adsorption mechanisms involved in each case were discussed and related to the adsorbents characteristics. The maximum adsorption capacity, Q0, given by the Langmuir model was 44.1 and 91.9 mg g-1 for fluoxetine and nicotinic acid adsorption, respectively.

A Diverse View of Science to Catalyse Change.

Valuing diversity leads to scientific excellence, the progress of science and most importantly, it is simply the right thing to do. We can value diversity not only in words, but also in actions.

Nanoporous Materials for the Onboard Storage of Natural Gas.

Climate change, global warming, urban air pollution, energy supply uncertainty and depletion, and rising costs of conventional energy sources are, among others, potential socioeconomic threats that our community faces today. Transportation is one of the primary sectors contributing to oil consumption and global warming, and natural gas (NG) is considered to be a relatively clean transportation fuel that can significantly improve local air quality, reduce greenhouse-gas emissions, and decrease the energy dependency on oil sources. Internal combustion engines (ignited or compression) require only slight modifications for use with natural gas; rather, the main problem is the relatively short driving distance of natural-gas-powered vehicles due to the lack of an appropriate storage method for the gas, which has a low energy density. The U.S. Department of Energy (DOE) has set some targets for NG storage capacity to obtain a reasonable driving range in automotive applications, ruling out the option of storing methane at cryogenic temperatures. In recent years, both academia and industry have foreseen the storage of natural gas by adsorption (ANG) in porous materials, at relatively low pressures and ambient temperatures, as a solution to this difficult problem. This review presents recent developments in the search for novel porous materials with high methane storage capacities. Within this scenario, both carbon-based materials and metal-organic frameworks are considered to be the most promising materials for natural gas storage, as they exhibit properties such as large surface areas and micropore volumes, that favor a high adsorption capacity for natural gas. Recent advancements, technological issues, advantages, and drawbacks involved in natural gas storage in these two classes of materials are also summarized. Further, an overview of the recent developments and technical challenges in storing natural gas as hydrates in wetted porous carbon materials is also included. Finally, an analysis of design factors and technical issues that need to be considered before adapting vehicles to ANG technology is also presented.

Engineering the Interface of Carbon Electrocatalysts at the Triple Point for Enhanced Oxygen Reduction Reaction.

The aqueous oxygen reduction reaction (ORR) has recently received increased attention due to its critical role in clean and sustainable energy-generation technologies, such as proton exchange membranes (PEM) fuel cells, alkaline fuel cells and Zn-air batteries. The sluggish kinetics associated with ORR result from multistep electron-transfer process. The slow kinetics are partially related to the O2 adsorption process onto the catalyst, which happens at the triple-phase boundary (TPB) of the electrocatalyst-electrolyte-oxygen interface. Hence, tremendous efforts have been devoted to improving the intrinsic properties of electrocatalysts such as active sites, electrical conductivity and porosity. Engineering the electrocatalyst's interfacial properties is another critical issue in ORR, however less described in the literature. The surface of the catalyst provides the microenvironment for the triple boundary interface reaction, which directly influences its electrocatalytic activity and the kinetics. This Minireview is a summary of the existing literature on manipulating the interfacial surface of non-precious metal catalysts at the triple point between the solid catalyst, the aqueous electrolyte and the O2 gas with the aim of improving the ORR efficiency. Various approaches towards improving the wettability and nanostructuring the catalyst surface to boost the activity of the surface-active sites and provide improved stability are discussed.

Sustainable carbon materials.

Carbon-based structures are the most versatile materials used in the modern field of renewable energy (i.e., in both generation and storage) and environmental science (e.g., purification/remediation). However, there is a need and indeed a desire to develop increasingly more sustainable variants of classical carbon materials (e.g., activated carbons, carbon nanotubes, carbon aerogels, etc.), particularly when the whole life cycle is considered (i.e., from precursor "cradle" to "green" manufacturing and the product end-of-life "grave"). In this regard, and perhaps mimicking in some respects the natural carbon cycles/production, utilization of natural, abundant and more renewable precursors, coupled with simpler, lower energy synthetic processes which can contribute in part to the reduction in greenhouse gas emissions or the use of toxic elements, can be considered as crucial parameters in the development of sustainable materials manufacturing. Therefore, the synthesis and application of sustainable carbon materials are receiving increasing levels of interest, particularly as application benefits in the context of future energy/chemical industry are becoming recognized. This review will introduce to the reader the most recent and important progress regarding the production of sustainable carbon materials, whilst also highlighting their application in important environmental and energy related fields.

Towards Negative Emissions: Hydrothermal Carbonization of Biomass for Sustainable Carbon Materials.

The contemporary production of carbon materials heavily relies on fossil fuels, contributing significantly to the greenhouse effect. Biomass is a carbon-neutral resource whose organic carbon is formed from atmospheric CO2. Employing biomass as a precursor for synthetic carbon materials can fix atmospheric CO2 into solid materials, achieving negative carbon emissions. Hydrothermal carbonization (HTC) presents an attractive method for converting biomass into carbon materials, by which biomass can be transformed into materials with favorable properties in a distinct hydrothermal environment, and these carbon materials have made extensive progress in many fields. However, the HTC of biomass is a complex and interdisciplinary problem, involving simultaneously the physical properties of the underlying biomass and sub/supercritical water, the chemical mechanisms of hydrothermal synthesis, diverse applications of resulting carbon materials, and the sustainability of the entire technological routes. This review starts with the analysis of biomass composition and distinctive characteristics of the hydrothermal environment. Then, the factors influencing the HTC of biomass, the reaction mechanism, and the properties of resulting carbon materials are discussed in depth, especially the different formation mechanisms of primary and secondary hydrochars. Furthermore, the application and sustainability of biomass-derived carbon materials are summarized, and some insights into future directions are provided.

Poly(ionic liquid) Ionomers Help Prevent Active Site Aggregation, in Single-Site Oxygen Reduction Catalysts.

Anion exchange membrane fuel cells (AEMFCs) can produce clean electricity without the need for platinum-group metals at the cathode. To improve their durability and performance, most research investigations so far have focused on optimizing the catalyst and anion exchange membrane, while few studies have been dedicated to the effect of the ionomer. Herein, we address this gap by developing a poly(ionic liquid)-based ionomer and studying its effect on oxygen transport and oxygen reduction kinetics, in comparison to the commercial proton exchange and anion exchange ionomers Nafion and Fumion. Our study shows that the choice of ionomer has a dramatic effect on the morphology of the catalyst layer, in particular on iron aggregation. We also observed that the quality of the catalyst layer and the degree of iron aggregation can be correlated to the rheological properties of the catalyst ink. Moreover, this work highlights the impact of the ionomer on the resistance to oxygen transport and reports improved oxygen diffusion compared to Nafion, for poly(ionic liquid)s with fluorinated anions. Finally, the performance of the catalyst-ionomer layer for oxygen reduction was tested with a rotating disc electrode (RDE) and a gas diffusion electrode (GDE). We observed dramatic differences between the two configurations, which we attribute to the different morphologies of the catalyst layer. In summary, our study highlights the dramatic and overlooked effect of the ionomer and the limitations of the RDE in predicting fuel cell performance.