RESUMO
Salicylic acid (SA) has for a long time been used to treat various skin disorders due to its anti-inflammatory, bacteriostatic, and antifungal properties. In the present work, mesoporous magnesium carbonate (MMC), a promising drug carrier, was modified with 3-aminopropyl-triethoxysilane to enable loading of SA. The amine modified MMC (aMMC) was successfully loaded with 8 wt.% of SA via a solvent evaporation method. SA was later completely released from the carrier in less than 15 min. Furthermore, the cytotoxicity of the functionalized material was evaluated. aMMC was found to be non-toxic for human dermal fibroblast cells with particle concentration of up to 1000 µg/mL when exposed for 48 h. The presented results form the basis of future development of aMMC as a potential carrier for SA in dermatological applications.
Assuntos
Aminas/química , Portadores de Fármacos/química , Magnésio/química , Ácido Salicílico/farmacologia , Administração Tópica , Linhagem Celular , Sobrevivência Celular/efeitos dos fármacos , Composição de Medicamentos , Sistemas de Liberação de Medicamentos/métodos , Liberação Controlada de Fármacos , Humanos , Microscopia Eletrônica de Varredura , Porosidade , Ácido Salicílico/administração & dosagem , Espectroscopia de Infravermelho com Transformada de FourierRESUMO
Historically, the shoulder arthroplasty humeral component has been designed for the management of infections, tumours and fractures. In all these cases the stem was needed as a scaffold. Original humeral components were not developed for use in shoulder arthritis, so these designs and derivates had a long stem. The newest humeral implants innovations consist in shortening of the implant, or even removing the whole stem, to rely on stemless fixation at the level of the metaphysis. This implies the advantages of preserved bone stock, less stress shielding, eliminating the diaphyseal stress riser, easier implant removal at revision, and humeral component placement independent from the humeral diaphyseal axis. Nowadays, surgeons try to balance the need for a stable fixation of the humeral component with the potential need for revision surgery. Complications of revision shoulder arthroplasty are related to the need for removing a well-fixed humeral stem, the length of the procedure, and the need to treat severe bone loss.
RESUMO
A calcium magnesium carbonate composite (CMC) material containing highly porous amorphous calcium carbonate (HPACC) and mesoporous magnesium carbonate (MMC) was synthesized. CMCs with varying HPACC : MMC mol ratios and high BET surface area (over 490 m2 g-1) were produced. The CMCs retained the morphology shared by HPACC and MMC. All these materials were built up of aggregated nanometer-sized particles. We tested the CO2 uptake properties of the synthesized materials. The CMCs were calcined at 850 °C to obtain the corresponding calcium magnesium oxide composites (CMOs) that contained CaO : MgO at different mol ratios. CMO with CaO : MgO = 3 : 1 (CMO-3) showed comparable CO2 uptake at 650 °C (0.586 g g-1) to CaO sorbents obtained from pure HPACC (0.658 g g-1) and the commercial CaCO3 (0.562 g g-1). Over 23 adsorption-desorption cycles CMOs also showed a lower CO2 uptake capacity loss (35.7%) than CaO from HPACC (51.3%) and commercial CaCO3 (79.7%). Al was introduced to CMO by the addition of Al(NO3)3 in the synthesis of CMC-3 to give ACMO after calcination. The presence of â¼19 mol% of Al(NO3)3 in ACMO-4 significantly enhanced its stability over 23 cycles (capacity loss of 5.2%) when compared with CMO-3 (calcined CMC-3) without adversely affecting the CO2 uptake. After 100 cycles, ACMO-4 still had a CO2 uptake of 0.219 g g-1. Scanning electron microscope images clearly showed that the presence of Mg and Al in CMO hindered the sintering of CaCO3 at high temperatures and therefore, enhanced the cycle stability of the CMO sorbents. We tested the CO2 uptake properties of CMO and ACMO only under ideal laboratory testing environment, but our results indicated that these materials can be further optimized as good CO2 sorbents for various applications.
RESUMO
(3-Aminopropyl)triethoxysilane (APTES) was used to modify the surface of mesoporous magnesium carbonate (MMC). The as-synthesized MMC had an average pore diameter of â¼5nm, but amine grafting occurred preferentially on the walls of the largest MMC pores. Analysis of ibuprofen (IBU) loading and release showed that IBU remained stable in the amorphous phase in all the MMC and modified MMC samples. The kinetics of IBU release from the modified MMC were assessed and used to evaluate the effects of the different functional groups. The release rate showed that the release of IBU could be controlled by adjusting the amine surface coverage of MMC and also by changing the surface groups. It was concluded that the interaction between the grafted functional groups in the modified MMC and the OH in the carboxyl groups of IBU was the most important factor for prolonging the release of the drug. These results are expected to lead to investigation of other as yet unexplored applications for MMC, including using it as a plastic additive and for gas separation.