Microstructure and mechanical behavior of cemented gold/tungsten mine tailings-crushed rock backfill: Effects of rock gradation and content.

Without appropriate and responsible waste management in place, the cursory storage of tailings and waste rocks on the surface can cause devastating damage to the planet's ecosystems. To proactively manage or abolish the damage, some techniques such as mine backfill have been already used repeatedly in mines. Microstructure and strength behavior of cementitious tailings-crushed rock backfill (CTCRB) with gold/tungsten tailings and rock contents (e.g., 10%, 20%, 30%, 40%, and 50%) were conducted in this study by using both UCS (unconfined compressive strength) tests (e.g., peak strengths, stress-strain curves, failure modes) and SEM micro-graphs. Key conclusions were shown that: when gradation and content of crushed rock was considered as 1-3 mm and 50% respectively, the UCS value of gold tailings based backfills was 1.02 MPa. In contrast, the UCS value of tungsten mine tailings based backfills was 1.36 MPa when the amount of crushed rock within the filling matrix became 10%. Tungsten tailings based backfills were more sensitive to crushed rock gradation than gold tailings based backfills. CTCRB's stress-strain curvatures were up-concave in the step of pore compaction. With the increase in the content and gradation of crushed rock, tungsten tailings based backfills showed swelling and crushing in complete destruction. Tailings' particle size, crushed rock content and gradation utterly affected the failure modes of CTCRB. Ettringite/CSH gel was found to be the leading hydration materials in the backfill matrix. The micro-cracks within CTCRB specimens were unfavorably correlated with its UCS data. To conclude, this study's main outcomes could give a significant guide for CTCRB's industrial uses.

Physico-chemical and micro-structural behavior of cemented mine backfill: Effect of pH in dam tailings.

The tailings created during ore processing have been a serious problem for mining companies and environment since it is a challenging task to effectively manage these highly voluminous/dangerous tailings. Therefore, several tailings disposal methods like tailings dams are needed for sustainable mining operations. The tailings accumulated in the dams reflect a critical raw material source since they might contain key base/precious metals, such as Au, Ag, Co, Ni, Cu and Zn. This study deals with the use-ability of dam tailings in cemented mine/paste backfill (CMB/CPB), considering the physico-chemical and micro-structural aspects. The backfill mixtures were manufactured at 76 wt% solid and 5 wt% cement contents, exposed to cure for up to 56 days, and tested for determining their strength (UCS), geo-chemical (i.e., pH, redox potential, and conductivity) and microstructure (i.e., XRD, TGA, and SEM) characteristics. Results disclosed that the strength of backfill was improved by the augmented basicity/age while only backfills made with sulfide-rich tailings had a noticeable drop in strength. This can be enlightened by the types of tailings (aged and fresh), and the hydration products shaped owing to the interaction of these tailings mixed with cement. While the values of pH detected by chemical tests were amplified up to 14 days, some decreased up to 56 days due to acid formations and erosions. This is the key function of CPB's deterioration physically, chemically, and microstructurally. Lastly, the outcomes of this study will allow us to further explore/assess the effects of dam tailings' potential usages on quality/performance of backfill mixtures.

Microstructure evolution and mechanical behavior of foamed cement-based tail backfills under varying fiber types and concentrations.

Industrial solid waste (mine tailings) management has emerged as the key universal ecological challenge as a result of the unceasing creation of rising waste by-products. Employing tailings makes mine fill production economical and assists resolve disposal problems. Foamed cement-based tailings backfill (FCTB) is a mine fill consisting of tailing, cement, water, and foaming agents. It provides certain advantages such as lightweight, good fluidity, and thermal insulation yet is relatively weak in strength. Additionally, FCTB's strength properties can be intensely improved by adding fibers. A total of three diverse fibers: polypropylene (PP), glass (G), and basalt (B) as well as dodecyltrimethylammonium bromide (DTAB) as a foaming agent were used to prepare fiber-reinforced foamed cementitious tailings backfill (FR-FCTB). The mechanical properties, energy evolution, ductility, and microstructure of FR-FCTB were elaborately investigated by uniaxial compression tests (UCS) and SEM. Laboratory findings demonstrate the reinforcing effect of three fibers on FCTB specimens: glass > polypropylene > basalt. FR-FCTB showed the best strength features as a fiber content of 0.3% was adopted in FCTB. At this time, the UCS performance of glass fiber-reinforced FCTBs was 0.85 MPa increased by 18.1%. The addition of fibers can increase the fill's energy storage limit, slow down the discharge of elastic strain energy within the backfill, and enhance the fill's ductility and toughness. The ductility factor evaluates the degree of deterioration of filling in terms of post-peak drop, with all FR-FCTB values being greater than CTB. FR-FCTB's chief hydration product is the C-S-H gel. Fiber's bridging effect significantly rallies crack extension and thus fill's strength features. Lastly, the study's main results are instructive for the industrial application of FR-FCTB used in metallic mines.

Long-term prognosis of patients with photosensitive idiopathic generalized epilepsy.

OBJECTIVE: The long-term prognosis of photosensitive idiopathic generalized epilepsy (p-IGE) is generally considered favorable; however, its specific characteristics remain unclear. Our objective was to investigate the extended prognosis of p-IGE. METHODS: We analyzed the demographics, clinical, and electroencephalographic (EEG) data of consecutive patients who were diagnosed as having p-IGE, who were under follow-up for a minimum of 10 years and exhibited a photoparoxysmal response (PPR) in their EEGs. Prognostic data, epilepsy course types, and electroclinical variables were compared using appropriate statistical methods. RESULTS: The mean follow-up duration for 108 consecutive patients with p-IGE (74.1 % female) was 16.8 ± 6.5 years. The main syndromes within this cohort included juvenile myoclonic epilepsy (37 %), juvenile absence epilepsy (15.7 %), and epilepsy with eyelid myoclonia (EEM) (14.8 %). In terms of epilepsy course types, 27.8 % were in the relapse-remission group, and 13.9 % had never experienced remission. A low early remission rate (5.6 %) was evident, with the remaining half of the cohort categorized as the late remission group. Several significant poor prognostic factors were identified including self-induction, clinical symptoms accompanying PPR, asynchrony and focal findings in EEG discharges, a wide frequency range of PPR, the coexistence of three seizure types, the presence of accompanying focal seizure features, and a history of convulsive status epilepticus. CONCLUSIONS: Our long-term follow-up study, conducted within a substantial p-IGE group, unveiled newly proposed course types within this epilepsy category and highlighted significant poor prognostic factors related to photosensitivity. These findings furnish valuable insights for precise prognosis counselling and effective management strategies for patients with p-IGE.

Acute effect of transcranial direct current stimulation on photoparoxysmal response.

INTRODUCTION: Transcranial direct current stimulation (tDCS) is a non-invasive technique, used to modify the excitability of the central nervous system. The main mechanism of tDCS is to change the excitability by subthreshold modulation by affecting neuronal membrane potentials in the direction of depolarization or repolarization. tDCS was previously investigated as an alternative adjunctive therapy in patients with epilepsy. We aimed here to investigate the acute effect of tDCS on the photoparoxysmal response (PPR) in EEG. METHODS: We enrolled 11 consecutive patients diagnosed with idiopathic generalized epilepsy who had PPR on at least 2 EEGs. Three different procedures, including sham, anodal, and cathodal tDCS were applied to the patients at intervals of one week by placing the active electrode over Oz, for 2 mA, 20 minutes. Spike-wave indices (SWI) were counted by two researchers independently and were compared during intermittent photic stimulation (IPS) on EEGs both before and after the application. RESULTS: After cathodal tDCS, SWI increased compared to baseline EEG and sham EEG in 3 patients, and after anodal tDCS, SWI increased in 2 patients. Although the SWI values did not change significantly, 8 patients reported subjectively that the applications were beneficial for them and that they experienced less discomfort during photic stimulation after the sessions. There were no side effects except transient skin rash in one patient, only. CONCLUSIONS: In our sham controlled tDCS study with both cathodal and anodal stimulation, our data showed that there was no significant change in SWI during IPS, despite subjective well-being. tDCS' modulatory effect does not seem to act in the acute phase on EEG parameters after photic stimulation.

Ultrasonic evaluation of strength properties of cemented paste backfill: Effects of mineral admixture and curing temperature.

This paper presents the findings of a research study designed and conducted to investigate the effects of mineral admixture and curing temperature on uniaxial compressive strength (UCS) and ultrasonic pulse velocity (UPV) behavior of laboratory-prepared cemented paste backfill (CPB) samples. A total of 290 CPB samples were prepared at different replacement rates (10-80%), cured at various temperatures (10-50 °C), and respectively subjected to both UPV and UCS testing after curing times of 3, 7, 14, 28, 56 and 90 days. The obtained experimental results show that the addition of fly ash (FA) can lead to an increase or decrease trend in UCS and UPV behavior of CPB samples, depending on the replacement level of admixtures. There is a competition between the strength-increasing factor (micro-filler effect of FA) and strength-decreasing factor (lower amount of cement hydration products induced by replacement ratio). Both UPV and UCS are found to decrease with increasing blast furnace slag (Slag) replacement level mainly attributable to its low pozzolanic reactivity. Besides, the curing temperature has a significant influence on UCS and UPV behavior, depending on the curing time. Results also suggest that UPV is less sensitive to the variation in the admixture dosage and curing temperature than UCS. As a result, there exists a clear linear relationship between UPV and UCS behavior of both CPB samples prepared with FA and/or Slag admixtures, and CPB samples tested at each curing temperature. The main findings of this research study suggest that the UPV test can be reliably used for predicting CPB's strength properties, saving money and time to mine operators.

Effect of lipid-containing, positively charged nanoemulsions on skin hydration, elasticity and erythema--an in vivo study.

Dry skin and other skin disorders such as atopic dermatitis are characterized by impaired stratum corneum (SC) barrier function and by an increase in transepidermal water loss (TEWL) leading to a decrease in skin hydration. The possibility that dermatological and cosmetic products containing SC lipids could play a part in the restoration of disturbed skin barrier function is of great interest in the field of dermatology and cosmetics. The aim of the present study was to evaluate the effect of positively charged oil/water nanoemulsions (PN) containing ceramide 3B and naturally found SC lipids (PNSC) such as ceramide 3, cholesterol, and palmitic acid on skin hydration, elasticity, and erythema. Creams of PNSC were compared to PN creams, to creams with negatively charged o/w nanoemulsion and SC lipids (NNSC) and to Physiogel cream, a SC lipid containing formulation, which is already on the market. The formulations (PN, PNSC, and NNSC) were prepared by high-pressure homogenization. After adding Carbopol 940 as thickener, particle size and stability of the creams were not significantly changed compared to the nanoemulsions. The studies were carried out on three groups, each with 14 healthy female test subjects between 25 and 50 years of age, using Corneometer 825, Cutometer SEM 575 and Mexameter 18 for measurements of skin hydration, elasticity, and erythema of the skin, respectively. The creams were applied regularly and well tolerated throughout the study. All formulations increased skin hydration and elasticity. There was no significant difference between PNSC and Physiogel. However, PNSC was significantly more effective in increasing skin hydration and elasticity than PN and NNSC indicating that phytosphingosine inducing the positive charge, SC lipids and ceramide 3B are crucial for the enhanced effect on skin hydration and viscoelasticity.

Design of a phytosphingosine-containing, positively-charged nanoemulsion as a colloidal carrier system for dermal application of ceramides.

Positively charged oil/water (o/w) nanoemulsions (PN) are effective vehicles to change the permeability of the skin. This study focused on the preparation and characterisation of phytosphingosine (PS) containing PN (PPN) which serve as colloidal carriers for the dermal application of ceramide IIIB (CIIIB) and the stratum corneum (SC) lipids (PPNSC) such as ceramide III (CIII), cholesterol, and palmitic acid. The investigations were conducted using appropriate emulsification and homogenisation processing conditions to optimise PPNSC with regard to droplet size, physical stability, and solubility of PS, CIII and CIIIB. A decrease in droplet size was observed through eight homogenisation cycles at a pressure of 500 bar and a temperature of 50 degrees C. Above these optimal values, an increase in droplet size was observed. PS and ceramides have low solubilities in oil and water. When Lipoid E-80 (LE80) was added to the oil phase, the solubility of PS and ceramides increased, indicating some interactions shown by DSC measurements. SC lipids and CIIIB could be successfully incorporated in PPN without producing any physical instability. The high stability of PPNSC is probably due to the presence of a hydrophilic (Tween 80) and a lipophilic surfactant (LE80), supported by the lipophilic cosurfactant PS, at the o/w interface. It was shown that PS was responsible for the positive charge and thus supported the high physical stability of PPNSC. This optimised emulsion was selected for further skin absorption evaluation.

In vitro and in vivo drug release from a novel in situ forming drug delivery system.

PURPOSE: The objective of this work was to investigate the influence of various preparation and formulation parameters on the in vitro and in vivo release of bupivacaine hydrochloride from an injectable in situ forming microparticle system (ISM). METHODS: The in vitro drug release of ISM was investigated as a function of various formulation and process parameters and was compared to the drug release from in situ forming implants and conventional microparticles. In vivo studies were carried out in male Sprague-Dawley rats. RESULTS: Upon contact with an aqueous medium, the internal polymer phase of the ISM system solidified and formed microparticles. The initial drug release from ISM systems was reduced with decreasing polymer phase/external oil phase ratio. An advantage of the ISM system compared to in situ implant systems was the significantly reduced burst effect, resulting in drug release profiles comparable to microparticles prepared by conventional methods. The in vivo drug release studies were in good agreement with the in vitro drug release. With the ISM system, the analgesic effect of the bupivacaine hydrochloride was prolonged when compared to the injection of a drug solution or drug-polymer solution. CONCLUSIONS: ISM are an attractive alternative for parenteral drug delivery systems.