Graphene/chitosan nanoreactors for ultrafast and precise recovery and catalytic conversion of gold from electronic waste.

The extraction of gold (Au) from electronic waste (e-waste) has both environmental impact and inherent value. Improper e-waste disposal poses environmental and health risks, entailing substantial remediation and healthcare costs. Large efforts are applied for the recovery of Au from e-waste using complex processes which include the dissolution of Au, its adsorption in an ionic state and succeeding reduction to metallic Au. These processes themselves being complex and utilizing harsh chemicals contribute to the environmental impact of e-waste. Here, we present an approach for the simultaneous recovery and reduction of Au3+ and Au+ ions from e-waste to produce solid Au0 forms, thus skipping several technological steps. We develop a nanoscale cross-dimensional composite material via self-assembly of two-dimensional graphene oxide and one-dimensional chitosan macromolecules, capable of acting simultaneously as a scavenger of gold ions and as a reducing agent. Such multidimensional architecture doesn't require to apply any voltage for Au adsorption and reduction and solely relies on the chemisorption kinetics of Au ions in the heterogeneous GO/CS nanoconfinements and their chemical reduction on multiple binding sites. The cooperative phenomena in ionic absorption are responsible for the extremely high efficiency of gold extraction. The extraction capacity reaches 16.8 g/g for Au3+ and 6.2 g/g for Au+, which is ten times larger than any existing gold adsorbents can propose. The efficiency is above 99.5 wt.% (current limit is 75 wt.%) and extraction ability is down to very low concentrations of 3 ppm.

Mechanochemical upcycling of spent LiCoO2 to new LiNi0.80Co0.15Al0.05O2 battery: An atom economy strategy.

The use of strong acids and low atom efficiency in conventional hydrometallurgical recycling of spent lithium-ion batteries (LIBs) results in significant secondary wastes and CO2 emissions. Herein, we utilize the waste metal current collectors in spent LIBs to promote atom economy and reduce chemicals consumption in a conversion process of spent Li1-xCoO2 (LCO) → new LiNi0.80Co0.15Al0.05O2 (NCA) cathode. Mechanochemical activation is employed to achieve moderate valence reduction of transition metal oxides (Co3+→Co2+,3+) and efficient oxidation of current collector fragments (Al0→Al3+, Cu0→Cu1+,2+), and then due to stored internal energy from ball-milling, the leaching rates of Li, Co, Al, and Cu in the ≤4 mm crushed products uniformly approach 100% with just weak acetic acid. Instead of corrosive precipitation reagents, larger Al fragments (≥4 mm) are used to control the oxidation/reduction potential (ORP) in the aqueous leachate and induce the targeted removal of impurity ions (Cu, Fe). After the upcycling of NCA precursor solution to NCA cathode powders, we demonstrate excellent electrochemical performance of the regenerated NCA cathode and improved environmental impact. Through life cycle assessments, the profit margin of this green upcycling path reaches about 18%, while reducing greenhouse gas emissions by 45%.

Investigating the Potential Use of Ni-Mn-Co (NMC) Battery Materials as Electrocatalysts for Electrochemical Water Splitting.

The imminent generation of significant amounts of Li ion battery waste is of concern due to potential detrimental environmental impacts. However, this also poses an opportunity to recycle valuable battery materials for later use. One underexplored area is using commonly employed cathode materials such as nickel, manganese cobalt (NMC) oxide as an electrocatalyst for water splitting reactions. In this work we explore the possibility of using NMC materials of different metallic ratios (NMC 622 and 811) as oxygen evolution and hydrogen evolution catalysts under alkaline conditions. We show that both materials are excellent oxygen evolution reaction (OER) electrocatalysts but perform poorly for the hydrogen evolution reaction. NMC 622 demonstrates the better OER activity with an overpotential of only 280 mV to pass 100 mA cm-2 and a low tafel slope of 42 mV dec-1. The material can also pass high current densities of 150 mA cm-2 for 24 h while also being tolerant to extensive potential cycling indicating suitability for direct integration with renewable energy inputs. This work demonstrates that NMC cathode materials if recovered from Li ion batteries are suitable OER electrocatalysts.

Identification of yttrium oxide-specific peptides for future recycling of rare earth elements from electronic scrap.

Yttrium is a heavy rare earth element (REE) that acquires remarkable characteristics when it is in oxide form and doped with other REEs. Owing to these characteristics Y2 O3 can be used in the manufacture of several products. However, a supply deficit of this mineral is expected in the coming years, contributing to its price fluctuation. Thus, developing an efficient, cost-effective, and eco-friendly process to recover Y2 O3 from secondary sources has become necessary. In this study, we used phage surface display to screen peptides with high specificity for Y2 O3 particles. After three rounds of enrichment, a phage expressing the peptide TRTGCHVPRCNTLS (DM39) from the random pVIII phage peptide library Cys4 was found to bind specifically to Y2 O3 , being 531.6-fold more efficient than the wild-type phage. The phage DM39 contains two arginines in the polar side chains, which may have contributed to the interaction between the mineral targets. Immunofluorescence assays identified that the peptide's affinity was strong for Y2 O3 and negligible to LaPO4 :Ce3+ ,Tb3+ . The identification of a peptide with high specificity and affinity for Y2 O3 provides a potentially new strategic approach to recycle this type of material from secondary sources, especially from electronic scrap.

Utilisation of acid-tolerant bacteria for base metal recovery under strongly acidic conditions.

Hydrometallurgical bioprocesses for base metal recovery in environmentally friendly electronic device waste (e-waste) recycling are typically studied under neutral pH conditions to avoid competition between metals and hydrogen ions. However, metal leachate is generally strongly acidic, thus necessitating a neutralisation process in the application of these bioprocesses to e-waste recycling. To solve this pH disparity, we focused on acid-tolerant bacteria for metal recovery under strongly acidic conditions. Four acid-tolerant bacterial strains were isolated from neutral pH environments to recover base metals from simulated waste metal leachate (pH 1.5, containing 100 or 1000 mg L-1 of Co, Cu, Li, Mn, and Ni) without neutralisation. The laboratory setting for sequential metal recovery was established using these strains and a reported metal-adsorbing bacterium, Micrococcus luteus JCM1464. The metal species were successfully recovered from 100 mg L-1 metal mixtures at the following rates: Co (8.95%), Cu (21.23%), Li (5.49%), Mn (13.18%), and Ni (9.91%). From 1000 mg L-1 metal mixtures, Co (7.23%), Cu (6.82%), Li (5.85%), Mn (7.64%), and Ni (7.52%) were recovered. These results indicated the amenability of acid-tolerant bacteria to environmentally friendly base metal recycling, contributing to the development of novel industrial application of the beneficial but unutilised bioresource comprising acid-tolerant bacteria.

Identification of Emerging Per- and Polyfluoroalkyl Substances (PFAS) in E-waste Recycling Practices and New Precursors for Trifluoroacetic Acid.

Electronic waste is an emerging source of per- and polyfluoroalkyl substance (PFAS) emissions to the environment, yet the contribution from hazardous recycling practices in the South Asian region remains unclear. This study detected 41 PFAS in soil samples from e-waste recycling sites in Pakistan and the total concentrations were 7.43-367 ng/g dry weight (dw) (median: 37.7 ng/g dw). Trifluoroacetic acid (TFA) and 6:2 fluorotelomer sulfonic acid emerged as the dominant PFAS, constituting 49% and 13% of the total PFAS concentrations, respectively. Notably, nine CF3-containing emerging PFAS were identified by the high-resolution mass spectrometry (HRMS)-based screening. Specifically, hexafluoroisopropanol and bistriflimide (NTf2) were consistently identified across all the samples, with quantified concentrations reaching up to 854 and 90 ng/g dw, respectively. This suggests their potential association with electronic manufacturing and recycling processes. Furthermore, except for NTf2, all the identified emerging PFAS were confirmed as precursors of TFA with molar yields of 8.87-40.0% by the TOP assay validation in Milli-Q water. Overall, this study reveals significant emission of PFAS from hazardous e-waste recycling practices and emphasizes the identification of emerging sources of TFA from precursor transformation, which are essential for PFAS risk assessment.

Abnormal erythrocyte-related parameters in children with Pb, Cr, Cu and Zn exposure.

The link between exposure to a particular heavy metal or metalloid and the development of anemia is well established. However, the association between combined exposure to multiple heavy metal(loid)s and anemia in children is still lacking in evidence. In this study, a total of 266 children aged 3 to 7 were recruited from Guiyu, China. Inductively coupled plasma mass spectrometry (ICP-MS) was used to measure blood heavy metal(loid) concentrations. Blood cell count, hemoglobin (HGB), mean corpuscular hemoglobin (MCH), mean corpuscular volume (MCV), mean corpuscular hemoglobin concentration (MCHC), hematocrit (HCT), and red blood cell distribution width (RDW) were measured by an automated hematology analyzer. Erythrocyte-related parameters were negatively correlated with the Cu and Cu/Zn ratios and positively correlated with Cr, Ni, Zn, and Se by Spearman correlation analysis. Only blood Cu level was negatively correlated with HGB [ß = -2.74, (95% Cl: -4.49, -0.995)], MCH [ß = -0.505, (95% Cl: -0.785, -0.226)], MCV [ß = -1.024, (95% Cl: -1.767, -0.281)], and MCHC [ß = -2.137, (95% Cl: -3.54, -0.734)] by multiple linear regression analysis. The Bayesian Kernel Machine Regression (BKMR) model analysis indicated a negative correlation between the combined exposure to Cu, Zn, Pb, and Cr and MCH and MCV. The single-factor analysis showed a considerable statistical difference only with Cu on MCV, MCH, and HGB. Furthermore, the interaction analysis highlighted the interdependent effects of Cu and Zn, Pb and Zn, and Cr and Zn on MCH and MCV levels. Additionally, the oxidation and/or antioxidation reactions may play a significant role in the development of metal(loid)-induced anemia risk. It is crucial to investigate the effects of co-exposure to multiple heavy metal(loid) elements on anemia, especially the interrelationships and mechanisms among them.

HBM4EU E-waste study: Assessing persistent organic pollutants in blood, silicone wristbands, and settled dust among E-waste recycling workers in Europe.

E-waste recycling is an increasingly important activity that contributes to reducing the burden of end-of-life electronic and electrical apparatus and allows for the EU's transition to a circular economy. This study investigated the exposure levels of selected persistent organic pollutants (POPs) in workers from e-waste recycling facilities across Europe. The concentrations of seven polychlorinated biphenyls (PCBs) and eight polybrominated diphenyl ethers (PBDEs) congeners were measured by GC-MS. Workers were categorized into five groups based on the type of e-waste handled and two control groups. Generalized linear models were used to assess the determinants of exposure levels among workers. POPs levels were also assessed in dust and silicone wristbands (SWB) and compared with serum. Four PCB congeners (CB 118, 138, 153, and 180) were frequently detected in serum regardless of worker's category. With the exception of CB 118, all tested PCBs were significantly higher in workers compared to the control group. Controls working in the same company as occupationally exposed (Within control group), also displayed higher levels of serum CB 180 than non-industrial controls with no known exposures to these chemicals (Outwith controls) (p < 0.05). BDE 209 was the most prevalent POP in settled dust (16 µg/g) and SWB (220 ng/WB). Spearman correlation revealed moderate to strong positive correlations between SWB and dust. Increased age and the number of years smoked cigarettes were key determinants for workers exposure. Estimated daily intake through dust ingestion revealed that ΣPCB was higher for both the 50th (0.03 ng/kg bw/day) and 95th (0.09 ng/kg bw/day) percentile exposure scenarios compared to values reported for the general population. This study is one of the first to address the occupational exposure to PCBs and PBDEs in Europe among e-waste workers through biomonitoring combined with analysis of settled dust and SWB. Our findings suggest that e-waste workers may face elevated PCB exposure and that appropriate exposure assessments are needed to establish effective mitigation strategies.

Association between 6PPD-quinone exposure and BMI, influenza, and diarrhea in children.

N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine-quinone (6PPD-quinone) has received extensive attention due to its ubiquitous distribution and potential toxicity. However, the distribution characteristics of 6PPD-quinone in dust from e-waste recycling areas and the consequential health risks to children are unclear. A total of 183 dust samples were collected from roads (n = 40), homes (n = 91), and kindergartens (n = 52) in Guiyu (the e-waste-exposed group) and Haojiang (the reference group) from 2019 to 2021. The results show that the concentrations of 6PPD-quinone in kindergarten and house dust from the exposed group were significantly higher than those from the reference group (P < 0.001). These findings show that e-waste may be another potential source of 6PPD-quinone, in addition to rubber tires. The exposure risk of 6PPD-quinone in children was assessed using their daily intake. The daily intake of 925 kindergarten children was calculated using the concentration of 6PPD-quinone in kindergarten dust. The daily intake of 6PPD-quinone via ingestion was approximately five orders of magnitude higher than via inhalation. Children in the exposed group had a higher exposure risk to 6PPD-quinone than the reference group. A higher daily intake of 6PPD-quinone from kindergarten dust was associated with a lower BMI and a higher frequency of influenza and diarrhea in children. This study reports the distribution of 6PPD-quinone in an e-waste recycling town and explores the associated health risks to children.

Tetrabromobisphenol-A/S and their derivatives in surface particulates from workshop floors of three representative e-waste recycling sites in China.

Surface particulates collected from the workshop floors of three major e-waste recycling sites (Taizhou, Qingyuan, and Guiyu) in China were analyzed for tetrabromobisphenol A/S (TBBPA/S) and their derivatives to investigate the environmental pollution caused by e-waste recycling activities. Mean concentrations of total TBBPA/S analogs in surface particulates were 31,471-116,059 ng/g dry weight (dw). TBBPA, TBBPA-BGE, and TBBPA-BDBPE were the most frequently detected in particulates with average concentration ranges of 17,929-78,406, 5601-15,842, and 5929-21,383 ng/g dw, respectively. Meanwhile, TBBPA, TBBPA-BGE, and TBBPA-BDBPE were the most abundant TBBPA/S analogs, accounting for around 96% of the total. The composition profiles of TBBPA/S analogs differed significantly among three e-waste sites. Similarly, principal component analysis uncovered different pollution patterns among different sites. The discrepancy in the profiles of TBBPA/S analogs largely relied on the e-waste types recycled in different areas. E-waste recycling led to the release of TBBPA/S analogs, and TBBPA/S analogs produced differentiation during migration from source (surface particulates) to nearby soil. More researches are necessary to find a definite relationship between pollution status and e-waste types and study differentiation behavior of TBBPA/S analogs in migration and diffusion from source to environmental medium.

Urinary metals and their associations with DNA oxidative damage among e-waste recycling workers in Hong Kong.

Recycling electronic waste (e-waste) poses risks of metal exposure, potentially leading to health impairments. However, no previous study has focused on this issue in Hong Kong. Therefore, from June 2021 to September 2022, this study collected urine samples from 101 e-waste workers and 100 office workers in Hong Kong to compare their urinary levels of metals using ICP-MS. Among the 15 included metals (with detection rates above the 70 % threshold), eight showed significantly higher urinary concentrations (unit: µg/g creatinine) in e-waste workers compared to office workers: Li (25.09 vs. 33.36), Mn (1.78 vs. 4.15), Ni (2.10 vs. 2.77), Cu (5.81 vs. 9.23), Zn (404.35 vs. 431.52), Sr (151.33 vs. 186.26), Tl (0.35 vs. 0.43), and Pb (0.69 vs. 1.16). E-waste workers in Hong Kong generally exhibited lower metal levels than those in developing regions but higher than their counterparts in developed areas. The urine level of 8-hydroxy-2-deoxyguanosine (8-OHdG) was determined by HPLC-MS/MS, and no significant difference was found between the two groups. Multiple linear regression models revealed no significant association between individual metal and urinary 8-OHdG concentrations. However, the metal mixture was identified to marginally elevate the 8-OHdG concentrations (1.12, 95 %CI: 0.04, 2.19) by quantile g­computation models, with Mn and Cd playing significant roles in such effect. In conclusion, while the metal levels among Hong Kong e-waste workers compared favorably with their counterparts in other regions, their levels were higher than those of local office workers. This underscores the need for policymakers to prioritize attention to this unique industry.

Biomarker responses in Danio rerio following an acute exposure (96 h) to e-waste leachate.

Electronic waste (e-waste) has been identified as an emerging pollutant and is the fastest growing waste stream at the present time. Significant technological development and modernization within the last decade has led to the rapid accumulation of outdated, broken and unwanted electrical and electronic equipment (EEE). Electronic products mainly consist of a range of metal containing components that, when disposed of improperly, could result in metal constituents leached into the environment and posing a health risk to humans and animals alike. Metal exposure can induce oxidative stress in organisms, which could lead to synergistic, antagonistic and additive effects. The metals found highest in abundance in the simulated e-waste leachate, were nickel (Ni), barium (Ba), zinc (Zn), lithium (Li), iron (Fe), aluminium (Al) and copper (Cu). An acute exposure study was conducted over a 96 h period to determine the potential toxicity of e-waste on the test organism Danio rerio. Biomarker analysis results to assess the biochemical and physiological effects induced by e-waste leachate, showed a statistically significant effect induced on acetylcholinesterase activity, superoxide dismutase, catalase activity, reduced glutathione content, glutathione s-transferase, malondialdehyde and glucose energy available. The Integrated Biomarker Response (IBRv2) analysis revealed a greater biomarker response induced as the exposure concentration of e-waste leachate increased.

Rhodococcus erythropolis ATCC 4277 behavior against different metals and its potential use in waste biomining.

Rhodococcus erythropolis bacterium is known for its remarkable resistance characteristics that can be useful in several biotechnological processes, such as bioremediation. However, there is scarce knowledge concerning the behavior of this strain against different metals. This study sought to investigate the behavior of R. erythropolis ATCC 4277 against the residue of chalcopyrite and e-waste to verify both resistive capacities to the metals present in these residues and their potential use for biomining processes. These tests were carried out in a stirred tank bioreactor for 48 h, at 24ºC, pH 7.0, using a total volume of 2.0 L containing 2.5% (v/v) of a bacterial pre-culture. The pulp density of chalcopyrite was 5% (w/w), and agitation and oxygen flow rates were set to 250 rpm and 1.5 LO2 min-1, respectively. On the other hand, we utilized a waste of computer printed circuit board (WPCB) with a pulp density of 10% (w/w), agitation at 400 rpm, and an oxygen flow rate of 3.0 LO2 min-1. Metal concentration analyses post-fermentation showed that R. erythropolis ATCC 4277 was able to leach about 38% of the Cu present in the chalcopyrite residue (in ~ 24 h), and 49.5% of Fe, 42.3% of Ni, 27.4% of Al, and 15% Cu present in WPCB (in ~ 24 h). In addition, the strain survived well in the environment containing such metals, demonstrating the potential of using this bacterium for waste biomining processes as well as in other processes with these metals.

Influence of Canadian provincial stewardship model attributes on the cost effectiveness of e-waste management.

This paper presents a comprehensive analysis of e-waste collection and management trends across six Canadian provinces, focusing on e-waste collection rates, provincial stewardship model attributes, program strategies and budget allocations from 2013 to 2020. Temporal and regression analyses were conducted using data from Electronic Product Recycling Association reports. A group characterization based on geographical proximity is proposed, aiming to explore the potential outcomes of fostering collaboration among neighboring provinces. The analysis emphasizes the significant impact of stewardship model attributes on e-waste collection rates, with Quebec emerging as a standout case, showcasing a remarkable 61.5% surge in collection rates. Findings from group analysis reveal a positive correlation between per capita e-waste collection rate and the growth of businesses and collection sites in Western Canada (Group A - British Columbia, Saskatchewan, and Manitoba). This highlights the potential benefits of a coordinated waste management approach, emphasizing the importance of shared resources and collaborative policies. Saskatchewan and Manitoba allocated only 6.6% and 7.0% of their respective budgets to e-waste transfer and storage. British Columbia's observed steady decrease of e-waste collection rate. In Group A, stewards handled 2.18-13.95 tonnes of e-waste during the study period. The cost per tonne of e-waste tended to be lower when more e-waste is managed per steward, suggesting the potential benefits of an integrated e-waste collection and management system.

A computer vision-based system for real-time component identification from waste printed circuit boards.

With an exponential increase in consumers' need for electronic products, the world is facing an ever-increasing economic and environmental threat of electronic waste (e-waste). To minimize their adverse effects, e-waste recycling is one of the pivotal factors that can help in minimizing the environmental pollution andto increase recovery of valuable materials. For instance, Printed Circuit Boards (PCBs), while they have several valuable elements, they are hazardous too; and therefore, they form a large chunk of e-waste being generated today. Thus, in recycling PCBs, Electronic Components (ECs) are segregated at first, and separately processed for recovering key elements that could be re-used. However, in the current recycling process, especially in developing nations, humans manually screen ECs, which goes on to affect their health. It also causes losses of valuable materials. Therefore, automated solutions need to be adopted for both to classify and to segregate ECs from waste PCBs. The study proposes a robust EC identification system based on computer vision and deep learning algorithms (YOLOv3) to automate sorting process which would help in further processing. The study uses a publicly available dataset, and a PCB dataset which reflect challenging recycling environments like lighting conditions, cast shadows, orientations, viewpoints, and different cameras/resolutions. The outcome of YOLOv3 detection model based on training of both datasets presents satisfactory classification accuracy and capability of real-time competent identification, which in turn, could help in automatically segregating ECs, while leading towards effective e-waste recycling.

Surface modification of toner-based recyclable iron oxide self-doped graphite nanocomposite to enhance methylene blue and tetracycline adsorption.

An innovative task was undertaken to convert ubiquitous and toxic electronic waste, waste toner powder (WTP), into novel adsorbents. Alkaline modification with KOH, NaOH, and NH4OH was employed for the first time to synthesize a series of surface-modified WTP with enhanced dispersibility and adsorption capacity. XRD, XRF, FTIR, and BET analyses confirmed that the prepared KOH-WTP, NaOH-WTP, and NH4OH-WTP were oxygen-functionalized self-doped iron oxide-graphite nanocomposites. The prepared adsorbents were used to remove methylene blue and tetracycline from aqueous solutions. KOH-WTP (0.1 g/100 mL) adsorbed 80% of 10 mg/L methylene blue within 1 h, while 0.1 g/100 mL NH4OH-WTP removed 72% of 10 mg/L tetracycline in 3 h. Exploring surface chemistry by altering solution pH and temperature suggested that hydrogen bonding, electrostatic interactions, π-π electron stacking, and pore filling were plausible adsorption mechanisms. Scanning electron microscopy revealed a diminishing adsorbents porosity after adsorption proving the filling of pores by the adsorbates. KOH-WTP and NH4OH-WTP removed 77% and 61% of methylene blue and tetracycline respectively in the fourth reuse. The adsorption data of methylene blue and tetracycline fitted the Freundlich isotherm model. The maximum adsorption capacities of KOH-WTP and NH4OH-WTP for methylene blue and tetracycline were 59 mg/g and 43 mg/g respectively. The prepared adsorbents were also compared with other adsorbents to assess their performance. The transformation of waste toner powder into magnetically separable oxygen-functionalized WTP with outstanding recyclability and adsorption capacity showcases a significant advancement in sustainable wastewater treatment. This further aligns with the principles of the circular economy through the utilization of toxic e-waste in value-added applications. Additionally, magnetic separation of surface-modified WTP post-treatment can curtail filtration and centrifugation expenses and adsorbent loss during wastewater treatment.

A biogenic hydrogel to recover Au(III) from electronic waste.

In the course of this investigation, we undertook the contemplation of a green chemistry paradigm with the express intent of procuring valuable metal, namely gold, from electronic waste (e-waste). In pursuit of this overarching objective, we conceived a procedural framework consisting of two pivotal stages. As an initial stage, we introduced a physical separation procedure relying on the utilization of the Eddy current separator, prior to embarking on the process of leaching from e-waste. Subsequent to the partitioning of metals from the non-metal constituents of waste printed circuit boards (PCB), we initiated an investigation into the hydrogel derived from basil seeds (Ocimum basilicum L.), utilizing it as a biogenic sorbent medium. The thorough characterization of hydrogel extracted from basil seeds involved the application of an array of analytical techniques, encompassing FTIR, XRD, SEM, and BET. The batch sorption experiments show more than 90% uptake in the pH range of 2-5. The sorption capacity of the hydrogel material was evaluated as 188.44 mg g-1 from the Langmuir Isotherm model. The potential interference stemming from a spectrum of other ions, encompassing Al, Cu, Ni, Zn, Co, Cr, Fe, Mn, and Pb was systematically examined. Notably, the sole instance of interference in the context of adsorption of gold ions was observed to be associated with the presence of lead. The application of the hydrogel demonstrated a commendable efficiency in the recovery of Au(III) from the leached solution derived from the waste PCB.

Preparation of 97% pure nickel-cobalt alloy from waste Ni-MH batteries by using waste glass as a fluxing agent.

With the e-waste growing rapidly all over the globe due to growing demand of electronics, smartphones, etc., coming up with an efficient and sustainable recycling process is the need of the hour. The present work reports a novel and sustainable process of manufacturing Ni alloy by bringing together three major waste streams such as waste Ni-MH batteries, e-waste plastics, and waste glass. The chosen temperature (1550 °C) favours the reduction of nickel-oxide by e-waste plastic as the reductant and sends rare earth elements present in the waste Ni-MH battery as oxide mixture to the slag phase. Waste glass powder used in this process functions as the fluxing agent, hence not requiring any additional flux. The reduction mechanism is gas-based, controlled mainly by hydrogen and carbon monoxide gases released as a result of decomposition of e-waste plastic as reaction commenced from cold zone (∼300 °C) to hot zone (1550 °C) in the horizontal tubular furnace. Formation of nickel alloy and enrichment of slag with mixture of rare earth oxides were confirmed by XRD, SEM-EDS, and Rietveld refining analysis performed on the XRD spectra of slag phase. ICP-OES (Inductively coupled plasma optical emission spectroscopy) and LIBS (laser induced breakdown spectrometer KT-100S) confirmed the high metal content in the alloy, thereby emphasizing the purity (∼98%) which is close to the composition of nickel super alloy. A maximum of 61% by weight REO enrichment was achieved in the slag phase, having La2O3:44.6%, Pr2O3:14.8%, and Nd2O3: 1.6% under optimised experimental conditions (1550 °C, 15 min, and 20% waste glass powder). This scientific investigation evinces a promising route for efficient utilisation of waste streams emanating from e-waste, thereby devising a sustainable recycling technique and protecting the environment, too.

Opportunities and challenges for circular economy in the Maldives: A stakeholder analysis of informal E-waste management in the Greater Malé Region.

In the Maldives, the contribution of the informal sector to e-waste management is significant as a formal e-waste management system is not yet established. The opportunities for advancing the circular economy in the Maldives' e-waste sector rely on the possibility of its formalization. This study aimed to examine the current and anticipated situations of e-waste management in the Greater Malé Region of the Maldives, with a specific focus on formalizing the informal sector. Interviews and questionnaire-based surveys were conducted followed by statistical analysis of the data. The t-test performed for the consumer survey data (n = 202) suggests that formalization encourages consumers to engage with the informal sector, resulting in increased resource recovery. Thematic analysis of interviews conducted with both formal and informal sector stakeholders (n = 17) revealed that the informal sector plays a substantial role in managing e-waste. It also underscored the need for government assistance to enhance safety and productivity in this sector. Various opportunities and challenges for establishing a circular economy in the country were identified, such as the rise in e-waste generation, the presence of an active informal workforce, the lack of sufficient government support, and prevailing stereotypes among consumers regarding informal workers. These findings provide a fresh perspective on the solutions for waste management in the Maldives and open the door to further explore the significance of the informal sector and feasible formalization initiatives. This study could contribute to the literature on the role of the informal sector in waste management in the Maldives and other small island developing states.

Development of complete hydrometallurgical processes for gold recovery from ICs and CPUs using ionic liquids.

Integrated circuits (ICs) and central processing units (CPUs), essential components of electrical and electronic equipment (EEE), are complex composite materials rich in recyclable high-value strategic and critical metals, with many in concentrations higher than in their natural ores. With gold the most valuable metal present, increase in demand for gold for EEE and its limited availability have led to a steep rise in the market price of gold, making gold recycling a high priority to meet demand. To overcome the limitations associated with conventional technologies for recycling e-waste, the use of greener technologies (ionic liquids (ILs) as leaching agents), offers greater potential for the recovery of gold from e-waste components. While previous studies have demonstrated the efficiency and feasibility of using ILs for gold recovery, these works predominantly concentrate on the extraction stage and often utilise simulated solutions, lacking the implementation of a complete process validated with real samples to effectively assess its overall effectiveness. In this work, a simulated Model Test System was used to determine the optimal leaching and extraction conditions before application to real samples. With copper being the most abundant metal in the e-waste fractions, to access the gold necessitated a two-stage pre-treatment (nitric acid leaching followed by aqua regia leaching) to ensure complete removal of copper and deliver a gold-enriched leach liquor. Gold extraction from the leach liquor was achieved by liquid-liquid extraction using Cyphos 101 (0.1 M in toluene with an O:A = 1:1, 20 °C, 150 rpm, and 15 min) and as a second process by sorption extraction with loaded resins (Amberlite XAD-7 with 300 mg of Cyphos 101/g of resins at 20 °C, 150 rpm and 3 h). In both processes, complete stripping and desorption of gold was achieved (0.5 M thiourea in 0.5 M HCl) and gold recovered, as nanoparticles of purity ≥95%, via a reduction step using a sodium borohydride solution (0.1 M NaBH4 in 0.1 M NaOH). These two hydrometallurgical processes developed can achieve overall efficiencies of ≥95% for gold recovery from real e-waste components, permit the reuse of the IL and resins up to five consecutive times, and offer a promising approach for recovery from any e-waste stream rich in gold.