Janus membranes derived from multi-shelled hollow spheres coated electrospun PVA membranes as phase change composites for photothermal conversion.

The development and preparation of multifunctional photothermal conversion materials has far-reaching significance for the utilization of solar energy resources in response to the energy crisis. Herein, we propose a Janus membrane for interfacial solar evaporation and phase change energy storage. The membranes were fabricated via combining the PVA film with multi-shelled hollow spheres (MHS). The membranes have asymmetric wettability, that is, one side is hydrophilic and the other side is hydrophobic. The as-resulted membranes obtain outstanding light absorption without further processing. According to these two advantages, the membranes were applied to solar evaporation. The evaporation rate of the membrane is 1.41 kg*m-2h-1 and the evaporation efficiency is 92.4 % under 1sun irradiation. Moreover, the membrane prepared by impregnating 1-Hexadecanamine (HDA) into MHS possesses excellent tensile strength (2.21 MPa) and photothermal conversion ability. The light-to-thermal conversion efficiency can reach 81.9 % under 1sun irradiation. Therefore, the membranes have broad application prospects in the field of photothermal conversion.

A Periosteum-Bioinspired Electrospun Janus Membrane with Antibacterial and Osteogenic Dual Function.

For a guided bone regeneration membrane, it is critical to possess osteogenic capability while inhibiting infection caused by bacteria. Inspired by the bilayer structure of the native periosteum, an electrospun Janus membrane with osteogenic and antibacterial dual-function is fabricated for guided bone regeneration. Hydrophilic moxifloxacin (MXF) and hydrophobic icariin (ICA) are loaded in the nanofibers made of a mixture of polycaprolactone and gelatin at the top and bottom layers, respectively, leading to the opposing hydrophilic/hydrophobic properties of the bilayer Janus membranes. The as-obtained Janus membrane exhibits excellent physical properties (tensile strength > 6.0 MPa) and robust biocompatibility, indicating the immense potential as a suitable replacement for the native periosteum. The membrane has a superior surface morphology and outstanding degradation performance in vitro. Besides, the rapid release of MXF and the slow release of ICA can meet the different needs of drug release rates. Only ≈30% ICA is released from the as-obtained Janus membrane after 21 d while almost 80% MXF is released. Mimicking the bilayer structure of the native periosteum, the electrospun Janus membrane containing ICA and MXF exhibits excellent comprehensive properties, which provides a promising strategy for preparing multifunctional scaffolds for tissue engineering.

A Janus, robust, biodegradable bacterial cellulose/Ti3C2Tx MXene bilayer membranes for guided bone regeneration.

Guided bone regeneration (GBR) stands as an essential modality for craniomaxillofacial bone defect repair, yet challenges like mechanical weakness, inappropriate degradability, limited bioactivity, and intricate manufacturing of GBR membranes hindered the clinical efficacy. Herein, we developed a Janus bacterial cellulose(BC)/MXene membrane through a facile vacuum filtration and etching strategy. This Janus membrane displayed an asymmetric bilayer structure with interfacial compatibility, where the dense layer impeded cell invasion and the porous layer maintained stable space for osteogenesis. Incorporating BC with Ti3C2Tx MXene significantly enhanced the mechanical robustness and flexibility of the material, enabling clinical operability and lasting GBR membrane supports. It also contributed to a suitable biodegradation rate, which aligned with the long-term bone repair period. After demonstrating the desirable biocompatibility, barrier role, and osteogenic capability in vitro, the membrane's regenerative potential was also confirmed in a rat cranial defect model. The excellent bone repair performance could be attributed to the osteogenic capability of MXene nanosheets, the morphological cues of the porous layer, as well as the long-lasting, stable regeneration space provided by the GBR membrane. Thus, our work presented a facile, robust, long-lasting, and biodegradable BC/MXene GBR membrane, offering a practical solution to craniomaxillofacial bone defect repair.

Janus Membranes with Asymmetric Superwettability for High-Performance and Long-Term On-Demand Oil/Water Emulsion Separation.

Current single-function superwettable materials are typically designed for either oil removal or water removal and are constrained by oil density, limiting their widespread applications. Janus membranes with opposite wettability on their two surfaces have recently emerged and present attractive opportunities for on-demand oil/water emulsion separation. Here, a combination strategy is introduced to prepare a Janus membrane with asymmetric superwettability for switchable oil/water emulsion separation. A mussel-inspired asymmetric interface introduction cooperating with the sequence-confined surface modification not only brings about an asymmetric superwettability Janus interface but also guarantees an outstanding stable interface and remarkable chemical stability surfaces. Specifically, the superhydrophilic surface with underwater superoleophobicity can separate surfactant-stabilized oil-in-water emulsions. Conversely, other surface displays opposite superhydrophobicity and superoleophilicity to treat surfactant-stabilized water-in-oil emulsions. Significantly, this superwettable Janus membrane presents superior long-term on-demand oil/water emulsion separation without obvious flux decline and high recovery ability because of its superwettability and superior stability. Furthermore, the asymmetric superwettability enhances the interfacial floatability at air-water interfaces, enabling the design of advanced interfacial materials. The as-prepared superwettable Janus membrane has established a cooperated separation system, overcoming the monotony of conventional superwettable membranes and expanding the application of these specialized membranes to oily wastewater treatment.

CsPbBr3 perovskite quantum dots-based Janus membrane with multifunction of luminescence, magnetism and aeolotropic electroconductivity.

Lead halide perovskite quantum dots (QDs) are promising semiconductors for next-generation photoelectric devices. However, the development of perovskite QDs-based multifunctional materials still needs to be addressed in order to further advance the application of perovskite QDs. Herein, a successful synthesis of Janus microfibers array Janus membrane (JMAJM) with up-down structure and multifunction of luminescence, magnetism and electroconductivity is firstly achieved based on CsPbBr3 QDs through a parallel electrospinning. JMAJM comprises up-down two layers tightly bonded together. The up-layer of JMAJM is luminescence/magnetism Janus microfibers array (L/M-JMAJM) constructed by [CsPbBr3/polymethyl methacrylate (PMMA)]//[CoFe2O4/PMMA] Janus microfibers as building elements. The down-layer of JMAJM is luminescence/electroconductivity Janus microfibers array (L/E-JMAJM) fabricated by [CsPbBr3/PMMA]//[polyaniline (PANI)/PMMA] Janus microfibers as building elements. Two independent microcosmic regions are designed and realized in a Janus microfiber, confining luminescence with magnetic or conductive substances into their respective regions, thus minimizing adverse effects of other dark-colored functional substances on the fluorescence of CsPbBr3 QDs. This peculiar Janus microfiber enables the effective separation and high integration of CsPbBr3 QDs with other functional substances. The up-down structure of JMAJM ensures a high integration of luminescence, magnetism and conductivity. Meanwhile, JMAJM addresses the environmental instability of CsPbBr3 QDs while simultaneously endows perovskite QDs-based materials with additional functions to realize multifunction. Under ultraviolet excitation, fluorescence characteristics of the CsPbBr3 QDs in JMAJM are maintained, exhibiting a vibrant green emission at 517 nm. Meanwhile, JMAJM achieves a maximum saturation magnetization of 20.32 emu·g-1, high conductance of 10-2 S and aeolotropic electroconductivity degree of 107. The combination of micro-partition with macro-partition in JMAJM receives superior concurrent luminescence-magnetic-conductive multifunction. This work provides a novel idea and strategy for advancing perovskite QDs-based multifunctional materials.

Green electrospun Janus membrane of polyether block amide (PEBA) doped with hierarchical magnesium hydrogen phosphate for the removal of pharmaceuticals and personal care products.

It has been a challenge to prepared polyether block amide (PEBA) fibrous membrane via solution electrospinning. The only few reported methods though involved hazardous solvents and surfactants which were against the principle of green chemistry. In this work, uniform fibrous membrane of PEBA was successfully fabricated by solution electrospinning with a bio-based solvent dihydrolevoglucosenone (Cyrene). To further improve the mechanical strength and adsorption performance of the PEBA membrane, a hierarchical magnesium hydrogen phosphate (MgHPO4·1.2H2O, MHP) was synthesized to blend evenly into the PEBA matrix. A Janus MHP/PEBA membrane with one side of hydrophobic surface and the other side of hydrophilic surface was subsequently prepared, which exhibited fast adsorption, high capacity, good selectivity and reusability towards ibuprofen, acetaminophen, carbamazepine and triclosan. In addition, the Janus membrane showed high removal efficiency of the above contaminants in secondary wastewater effluent with good long term stability. It demonstrated that this Janus MHP/PEBA membrane had a good potential in practical wastewater treatment.

Janus Membrane-Based Wearable pH Sensor with Sweat Absorption, Gas Permeability, and Self-Adhesiveness.

Wearable biomedical sensors have enabled noninvasive and continuous physiological monitoring for daily health management and early detection of chronic diseases. Among biomedical sensors, wearable pH sensors attracted significant interest, as pH influences most biological reactions. However, conformable pH sensors that have sweat absorption ability, are self-adhesive to the skin, and are gas permeable remain largely unexplored. In this study, we present a pioneering approach to this problem by developing a Janus membrane-based pH sensor with self-adhesiveness on the skin. The sensor is composed of a hydrophobic polyurethane-polydimethylsiloxane porous hundreds nanometer-thick substrate and a hydrophilic poly(vinyl alcohol)-poly(acrylic acid) porous nanofiber layer. This Janus membrane exhibits a thickness of around 10 µm, providing a conformable adhesion to the skin. The simultaneous realization of solution absorption, gas permeability, and self-adhesiveness makes it suitable for long-term continuous monitoring without compromising the comfort of the wearer. The pH sensor was tested successfully for continuous monitoring for 7.5 h, demonstrating its potential for stable analysis of skin health conditions. The Janus membrane-based pH sensor holds significant promise for comprehensive skin health monitoring and wearable biomedical applications.

Multifunctional Janus Membrane for Diabetic Wound Healing and Intelligent Monitoring.

The complex microenvironment of diabetic wounds often hinders the healing process, ultimately leading to the formation of diabetic foot ulcers and even death. Dual monitoring and treatment of wounds can significantly reduce the incidence of such cases. Herein, a multifunctional Janus membrane (3D chitosan sponge-ZE/polycaprolactone nanofibers-ZP) was developed by incorporating the zinc metal-organic framework, europium metal-organic framework, and phenol red into nanofibers for diabetic wound monitoring and treatment. The directional water transport capacity of the resulting Janus membrane allows for unidirectional and irreversible drainage of wound exudate, and the multifunctional Janus membrane creates up to a 99% antibacterial environment, both of which can treat wounds. Moreover, the pH (5-8) and H2O2 (0.00-0.80 µM) levels of the wound can be monitored using the color-changing property of phenol red and the fluorescence characteristic of Eu-MOF on the obtained membrane, respectively. The healing stages of the wound can also be monitored by analyzing the RGB values of the targeted membrane images. This design can more accurately reflect the wound state and treat the wound to reduce bacterial infection and accelerate wound healing, which has been demonstrated in in vivo experiments. The results provide an important basis for early intervention in diabetic patients.

Surface energy-induced anti-wetting and anti-fouling enhancement of Janus membrane for membrane distillation.

Membrane distillation (MD) presents a promising alternative to conventional desalination systems, particularly for the treatment of hypersaline wastewater. However, the large-scale application of MD is hindered by challenges such as membrane wetting, membrane fouling, and low permeate flux. Herein, we proposed an air/liquid interface deposition method to fabricate a Janus membrane, termed the PVDF-PDA/PEI-Si membrane. The membrane featured a nanosieving, superhydrophilic polydopamine/polyethylenimine (PDA/PEI) layer decorated with silica nanoparticles, coupled with a microporous, hydrophobic polyvinylidene fluoride (PVDF) layer. The introduction of a dense PDA/PEI-Si layer featuring high surface energy significantly enhanced the wetting and fouling resistance of the membrane, with a minor effect on the permeate flux. The performance enhancement was particularly evident when hypersaline water containing sodium dodecyl sulfate (SDS) and oily contaminants was used as the feed. The interactions between the membrane and contaminants were calculated using the XDLVO theory and molecular dynamics simulations to elucidate the mechanisms underlying the enhanced anti-wetting and anti-fouling properties, respectively. According to the XDLVO theory, a large energy barrier must be overcome for the SDS to attach onto the PDA/PEI-Si surface. Meanwhile, molecular dynamics simulations confirmed the weak interaction energy between the oily foulants and the PVDF-PDA/PEI-Si membrane due to its high surface energy. This study presents a promising approach for the fabrication of high-performance MD membranes and provides new insights into the mechanisms underlying the enhanced anti-wetting and anti-fouling properties.

Shear Flow-Assembled Janus Membrane with Bifunctional Osteogenic and Antibacterial Effects for Guided Bone Regeneration.

Guided bone regeneration (GBR) membranes that reside at the interface between the bone and soft tissues for bone repair attract increasing attention, but currently developed GBR membranes suffer from relatively poor osteogenic and antibacterial effects as well as limited mechanical property and biodegradability. We present here the design and fabrication of a bifunctional Janus GBR membrane based on a shear flow-driven layer by a layer self-assembly approach. The Janus GBR membrane comprises a calcium phosphate-collagen/polyethylene glycol (CaP@COL/PEG) layer and a chitosan/poly(acrylic acid) (CHI/PAA) layer on different sides of a collagen membrane to form a sandwich structure. The membrane exhibits good mechanical stability and tailored biodegradability. It is found that the CaP@COL/PEG layer and CHI/PAA layer contribute to the osteogenic differentiation and antibacterial function, respectively. In comparison with the control group, the Janus GBR membrane displays a 2.52-time and 1.84-time enhancement in respective volume and density of newly generated bone. The greatly improved bone repair ability of the Janus GBR membrane is further confirmed through histological analysis, and it has great potential for practical applications in bone tissue engineering.

Exudate Unidirectional Pump to Promote Glucose Catabolism Triggering Fenton-Like Reaction for Chronic Diabetic Wounds Therapy.

The massive accumulation of exudate containing high concentrations of glucose causes wound infection and triggers the release of inflammatory factors, which in turn delays the closure of diabetic wounds. In this study, a Janus membrane is constructed by combining glucose oxidase (GOx) and copper ions (Cu2+) for the treatment of diabetic wounds, which is named as Janus@GOx/Cu2+. It consists of hydrophobic, transitional, and superhydrophilic layers in a three-layer structure with gradient hydrophilicity for self-pumping properties. The Janus@GOx/Cu2+ membrane triggers a series of cascading reactions while pumping out diabetic wound exudates. First, glucose oxidase loaded onto the hydrophilic layer of the Janus@GOx/Cu2+ membrane decomposes glucose into hydrogen peroxide (H2O2) and glucuronic acid, reducing the local glucose level. The generated glucuronic acid neutralizes the local alkaline environment of chronic wounds. Simultaneously, the H2O2 interacts with the Cu2+ contained in the hydrophobic layers of the Janus@GOx/Cu2+ membrane via a Fenton-like reaction, generating hydroxyl radicals with excellent bactericidal properties. Cu2+ promotes angiogenesis and wound healing in diabetic wounds. Under the action of multiple responses, the Janus@GOx/Cu2+ membrane promotes wound healing in diabetic infections.