Enhanced solar-driven photoelectrochemical water splitting using nanoflower Au/CuO/GaN hybrid photoanodes.

Harnessing solar energy for large-scale hydrogen fuel (H2) production shows promise in addressing the energy crisis and ecological degradation. This study focuses on the development of GaN-based photoelectrodes for efficient photoelectrochemical (PEC) water splitting, enabling environmentally friendly H2 production. Herein, a novel nanoflower Au/CuO/GaN hybrid structure was successfully synthesized using a combination of methods including successive ionic layer adsorption and reaction (SILAR), RF/DC sputtering, and metal-organic chemical vapour deposition (MOCVD) techniques. Structural, morphological, and optical characteristics and elemental composition of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-Vis spectroscopy, and energy-dispersive X-ray (EDX) spectroscopy, respectively. PEC and electrochemical impedance measurements were performed for all samples. The nanoflower Au/CuO/GaN hybrid structure exhibited the highest photocurrent density of ∼4 mA cm-2 at 1.5 V vs. RHE in a Na2SO4 electrolyte with recorded moles of H2 of about 3246 µmol h-1 cm-2. By combining these three materials in a unique structure, we achieved improved performance in the conversion of solar energy into chemical energy. The nanoflower structure provides a large surface area and promotes light absorption while the Au, CuO, and GaN components contribute to efficient charge separation and transfer. This study presents a promising strategy for advancing sustainable H2 production via efficient solar-driven water splitting.

Sputtered Cu-doped NiO thin films as an efficient electrocatalyst for methanol oxidation.

The efficient electrocatalysts for direct methanol oxidation play an essential role in the electrochemical energy conversion systems for their application in a wide range of portable applications. Consequently, Cu-doped NiO thin films on fluorine-doped tin oxide (FTO) were successfully prepared by the co-sputtering deposition technique, using various deposition times (300, 600, 900, and 1200 seconds), and producing films of different thicknesses (30, 55, 90, and 120 nm, respectively). X-ray diffraction (XRD) revealed the ideal crystallinity of the structure of the prepared films and was used to observe the effect of the thickness of the films on the crystal size. Energy-dispersive X-ray spectroscopy (EDS) confirmed the purity of the deposited film without any contamination. Field emission scanning electron microscopy (FESEM) images confirmed the film thickness increase with increasing deposition time. The surface roughness value of the Cu-NiO 1200 film was found to be 3.2 nm based on the atomic force microscopy (AFM) measurements. The deposited thin films of different thicknesses have been used as electrocatalysts for methanol oxidation at various concentrations of methanol (0, 0.5, 1, and 2 M), and displayed the highest electrocatalytic performance in 1 M methanol. Cu-doped NiO thin films have the advantage as electrocatalysts where they can be used directly without adding any binder or conducting agents, this is because Cu-doped NiO is deposited with high adhesion and strong electrical contact to the FTO substrate. A clear impact on the catalytic activity with increasing film thickness and a correlation between the film thickness and its catalytic activity was observed. The current density increased by about 60% for the Cu-NiO 1200 sample compared to Cu-NiO 300 sample, with the lowest onset potential of 0.4 V vs. Ag/AgCl. All deposited thin films of different thicknesses exhibited high stability at 0.6 V in 1 M methanol. This will open the window toward using physical deposition techniques for optimizing the electrocatalytic activity of different catalysts for electrocatalytic applications.

Structural, Optical, and Electrical Investigations of Nd2O3-Doped PVA/PVP Polymeric Composites for Electronic and Optoelectronic Applications.

In this present work, a PVA/PVP-blend polymer was doped with various concentrations of neodymium oxide (PB-Nd+3) composite films using the solution casting technique. X-ray diffraction (XRD) analysis was used to investigate the composite structure and proved the semi-crystallinity of the pure PVA/PVP polymeric sample. Furthermore, Fourier transform infrared (FT-IR) analysis, a chemical-structure tool, illustrated a significant interaction of PB-Nd+3 elements in the polymeric blends. The transmittance data reached 88% for the host PVA/PVP blend matrix, while the absorption increased with the high dopant quantities of PB-Nd+3. The absorption spectrum fitting (ASF) and Tauc's models optically estimated the direct and indirect energy bandgaps, where the addition of PB-Nd+3 concentrations resulted in a drop in the energy bandgap values. A remarkably higher quantity of Urbach energy for the investigated composite films was observed with the increase in the PB-Nd+3 contents. Moreover, seven theoretical equations were utilized, in this current research, to indicate the correlation between the refractive index and the energy bandgap. The indirect bandgaps for the proposed composites were evaluated to be in the range of 5.6 eV to 4.82 eV; in addition, the direct energy gaps decreased from 6.09 eV to 5.83 eV as the dopant ratios increased. The nonlinear optical parameters were influenced by adding PB-Nd+3, which tended to increase the values. The PB-Nd+3 composite films enhanced the optical limiting effects and offered a cut-off laser in the visible region. The real and imaginary parts of the dielectric permittivity of the blend polymer embedded in PB-Nd+3 increased in the low-frequency region. The AC conductivity and nonlinear I-V characteristics were augmented with the doping level of PB-Nd+3 contents in the blended PVA/PVP polymer. The outstanding findings regarding the structural, electrical, optical, and dielectric performance of the proposed materials show that the new PB-Nd+3-doped PVA/PVP composite polymeric films are applicable in optoelectronics, cut-off lasers, and electrical devices.

Electrocatalytic Degradation of Rhodamine B Using Li-Doped ZnO Nanoparticles: Novel Approach.

In this paper, we discuss the preparation of Li-doped ZnO nanostructures through combustion and report on their structural, morphological, optical, and electrocatalysis properties. X-ray diffraction analyses show that the samples have a structure crystallized into the usual hexagonal wurtzite ZnO structure according to the P63mc space group. The scanning electron microscope images conceal all samples' nanosphere bundles and aggregates. The reflectance spectra analysis showed that the direct bandgap values varied from 3.273 eV (for pure ZnO, i.e., ZnL1) to 3.256 eV (for high Li-doped ZnO). The measured capacitance concerning frequency has estimated the variation of dielectric constant, dielectric loss, and AC conductivity against AC electric field frequency. The dielectric constant variations and AC conductivity are analyzed and discussed by well-known models such as Koop's phenomenological theory and Jonscher's law. The Raman spectra have been recorded and examined for the prepared samples. Rhodamine B was electro-catalytically degraded in all prepared samples, with the fastest time for ZnL5 being 3 min.

Enhancement in the Structural, Electrical, Optical, and Photocatalytic Properties of La2O3-Doped ZnO Nanostructures.

A lanthanum oxide (La2O3)-ZnO nanostructured material was synthesized in the proposed study with different La2O3 concentrations, 0.001 g to 5 g (named So to S7), using the combustion method. X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transformation infrared spectroscopy (FT-IR) were utilized for investigating the structure, morphology, and spectral studies of the La2O3- ZnO nanomaterials, respectively. The results obtained from previous techniques support ZnO's growth from crystalline to nanoparticles' fine structure by changing the concentrations of lanthanum oxide (La2O3) dopants in the host matrix. The percentage of ZnO doped with La- influences the ZnO photocatalytic activity. SEM analysis confirmed the grain size ranged between 81 and 138 nm. Furthermore, UV-Vis diffuse reflectance spectroscopy was performed to verify the effects of La2O3 dopants on the linear optical properties of the nano-composite oxides. There was a variation in the energy bandgaps of La2O3-ZnO nanocomposites, increasing the weight concentrations of lanthanum dopants. The AC electrical conductivity, dielectric properties, and current-voltage properties support the enactment of the electrical characteristics of the ZnO nanoparticles by adding La2O3. All the samples under investigation were used for photodegradation with Rhodamine B (RhB) and Methylene Blue (MB). In less than 30 min of visible light irradiation, S4 (0.5 g) La2O3-ZnO reached 99% of RhB and MB degradation activity. This study showed the best photocatalytic effect for RhB and MB degradation of 0.13 and 0.11 min-1 by 0.5 g La2O3-ZnO. Recycling was performed five times for the nanocatalysts that displayed up to 98 percent catalytic efficiency for RhB and MB degradation in 30 min. The prepared La2O3-ZnO nanostructured composites are considered novel candidates for various applications in biomedical and photocatalytic studies.

Development of Nanocoated Filaments for 3D Fused Deposition Modeling of Antibacterial and Antioxidant Materials.

Three-dimensional (3D) printing is one of the most futuristic manufacturing technologies, allowing on-demand manufacturing of products with highly complex geometries and tunable material properties. Among the different 3D-printing technologies, fused deposition modeling (FDM) is the most popular one due to its affordability, adaptability, and pertinency in many areas, including the biomedical field. Yet, only limited amounts of materials are commercially available for FDM, which hampers their application potential. Polybutylene succinate (PBS) is one of the biocompatible and biodegradable thermoplastics that could be subjected to FDM printing for healthcare applications. However, microbial contamination and the formation of biofilms is a critical issue during direct usage of thermoplastics, including PBS. Herein, we developed a composite filament containing polybutylene succinate (PBS) and lignin for FDM printing. Compared to pure PBS, the PBS/lignin composite with 2.5~3.5% lignin showed better printability and antioxidant and antimicrobial properties. We further coated silver/zinc oxide on the printed graft to enhance their antimicrobial performance and obtain the strain-specific antimicrobial activity. We expect that the developed approach can be used in biomedical applications such as patient-specific orthoses.

The Auto-Combustion Method Synthesized Eu2O3- ZnO Nanostructured Composites for Electronic and Photocatalytic Applications.

An efficient and environmentally friendly combustion technique was employed to produce ZnO nanopowders with different Eu concentrations (from 0.001 g to 5 g). The structural morphology of the Eu2O3-ZnO nanocomposites was examined using XRD, SEM, and infrared spectroscopy (FT-IR). In addition, UV-Vis diffuse reflectance spectroscopy was also used to investigate the effects of europium (Eu) dopant on the optical behaviors and energy bandgaps of nano-complex oxides. The photocatalytic degradation efficiency of phenol and methylene blue was investigated using all the prepared Eu2O3-ZnO nanostructured samples. Photocatalytic effectiveness increased when europium (Eu) doping ratios increased. After adding moderate Eu, more hydroxyl radicals were generated over ZnO. The best photocatalyst for phenol degradation was 1 percent Eu2O3-ZnO, while it was 0.5 percent Eu2O3-ZnO for methylene blue solutions. The obtained Eu2O3-doped ZnO nanostructured materials are considered innovative, promising candidates for a wide range of nano-applications, including biomedical and photocatalytic degradation of organic dyes and phenol.

The Photocatalytic Performance of Nd2O3 Doped CuO Nanoparticles with Enhanced Methylene Blue Degradation: Synthesis, Characterization and Comparative Study.

The growth of the textile industry results in a massive accumulation of dyes on water. This enormous rise in pigments is the primary source of water pollution, affecting the aquatic lives and our ecosystem balance. This study aims to notify the fabrication of neodymium incorporated copper oxide (Nd2O3 doped CuO) nanoparticles by combustion method for effective degradation of dye, methylene blue (MB). X-ray diffraction (XRD), Field emission Scanning electron microscopy (FESEM), Zeta potential have been applied for characterization. Photocatalyst validity has been evaluated for methylene blue degradation (MB). Test conditions such as time of contact, H2O2, pH, and photo-Fenton have been modified to identify optimal degradation conditions. Noticeably, 7.5% Nd2O3 doped CuO nanoparticle demonstrated the highest photocatalytic efficiency, up to 90.8% in 80 min, with a 0.0227 min-1 degradation rate. However, the photocatalytic efficiency at pH 10 becomes 99% with a rate constant of 0.082 min-1. Cyclic experiments showed the Nd2O3 doped CuO nanoparticle's stability over repeated use. Scavenge hydroxyl radical species responsible for degradation using 7.5% Nd2O3 doped CuO nanoparticles have been investigated under visible irradiation.

Fabrication and Characterization of Highly Efficient As-Synthesized WO3/Graphitic-C3N4 Nanocomposite for Photocatalytic Degradation of Organic Compounds.

The incorporation of tungsten trioxide (WO3) by various concentrations of graphitic carbon nitride (g-C3N4) was successfully studied. X-ray diffraction (XRD), Scanning Electron Microscope (SEM), and Diffused Reflectance UV-Vis techniques were applied to investigate morphological and microstructure analysis, diffused reflectance optical properties, and photocatalysis measurements of WO3/g-C3N4 photocatalyst composite organic compounds. The photocatalytic activity of incorporating WO3 into g-C3N4 composite organic compounds was evaluated by the photodegradation of both Methylene Blue (MB) dye and phenol under visible-light irradiation. Due to the high purity of the studied heterojunction composite series, no observed diffraction peaks appeared when incorporating WO3 into g-C3N4 composite organic compounds. The particle size of the prepared composite organic compound photocatalysts revealed no evident influence through the increase in WO3 atoms from the SEM characteristic. The direct and indirect bandgap were recorded for different mole ratios of WO3/g-C3N4, and indicated no apparent impact on bandgap energy with increasing WO3 content in the composite photocatalyst. The composite photocatalysts' properties better understand their photocatalytic activity degradations. The pseudo-first-order reaction constants (K) can be calculated by examining the kinetic photocatalytic activity.