Liquid uptake in porous cellulose sheets studied with UFI-NMR: Penetration, swelling and air displacement.

Liquid penetration in porous cellulosic materials is crucial in many technological fields. The complex geometry, small pore size, and often fast timescale of liquid uptake makes the process hard to capture. Effects such as swelling, vapor transport, film flow and water transport within cellulosic material makes transport deviate from well-known relations such as Lucas-Washburn and Darcy's Law. In this work it is demonstrated how Ultra-Fast Imaging NMR can be used to simultaneously monitor the liquid distribution and swelling during capillary uptake of water with a temporal- and spatial resolution of 10 ms and 14.5-18 µm respectively. The measurements show that in a cellulose fiber sheet, within the first 65 ms, liquid first penetrates the whole sheet before swelling takes place for another 30 s. Furthermore, it was observed that the liquid front traps 15 v% of air which is slowly replaced by water during the final stage of liquid uptake. Our method makes it possible to simultaneously quantify the concentration of all three phases (solid, liquid and air) within porous materials during processes exceeding 50 ms (5 times the temporal resolution). We hence believe that the proposed method should also be useful to study liquid penetration, or water diffusion, into other porous cellulosic materials like foams, membranes, nonwovens, textiles and films.

Ultra Fast Imaging NMR method for measuring fast transport processes in thin porous media.

Measuring moisture distributions during fast transport processes in thin porous media is a challenging task. In this paper, Ultra Fast Imaging (UFI) NMR is proposed as a valuable measurement technique for investigating moisture uptake in porous media by achieving a temporal resolution of 10 ms and spatial resolution between 14.5 and 18 µm. This paper gives a detailed explanation about the methodology and the interpretation of the signal intensity. It is shown that there exist specific T1- and T2- relaxation time conditions for performing UFI experiments with signal-to-noise ratios that are sufficiently high. In most cases, a contrast agent is required to optimize these relaxation times and achieve the optimal measurement conditions. In the first part of this paper, both CuSO4 and Clariscan are discussed as possible contrast agents. Furthermore, it is shown that the signal intensity can be linked to the moisture content for water based liquids. The second part of this paper covers penetration experiments on porous PVDF membranes. These measurements show that the technique is able to measure moisture profiles during fast capillary penetration and allows to extract moisture front positions. Those front positions follow a linear time behavior in PVDF membranes. Lastly the NMR-measurements showed similar results when compared to scanning absorptometry (ASA).

High-speed NMR imaging of capillary action in thin nontransparent porous media.

An improved high-speed NMR profiling method is introduced that enables us to measure capillary action in thin, nontransparent porous media. Liquid profiles can be measured as fast as 10 ms with a spatial resolution of 14.5µm. Capillary absorption of microliter-sized droplets into nontransparent nylon-6,6 porous membranes was studied. In nylon-6,6 sharp fronts obeying a one-dimensional Darcy model were observed. In paper the uptake did not follow this model: retardation in uptake, broader fluid fronts, and swelling was observed. These measurements nicely demonstrate the possibilities and versatility of the developed method.

New and Interesting Fungi. 4.

An order, family and genus are validated, seven new genera, 35 new species, two new combinations, two epitypes, two lectotypes, and 17 interesting new host and / or geographical records are introduced in this study. Validated order, family and genus: Superstratomycetales and Superstratomycetaceae (based on Superstratomyces ). New genera: Haudseptoria (based on Haudseptoria typhae); Hogelandia (based on Hogelandia lambearum); Neoscirrhia (based on Neoscirrhia osmundae); Nothoanungitopsis (based on Nothoanungitopsis urophyllae); Nothomicrosphaeropsis (based on Nothomicrosphaeropsis welwitschiae); Populomyces (based on Populomyces zwinianus); Pseudoacrospermum (based on Pseudoacrospermum goniomae). New species: Apiospora sasae on dead culms of Sasa veitchii (Netherlands); Apiospora stipae on dead culms of Stipa gigantea (Spain); Bagadiella eucalyptorum on leaves of Eucalyptus sp. (Australia); Calonectria singaporensis from submerged leaf litter (Singapore); Castanediella neomalaysiana on leaves of Eucalyptus sp. (Malaysia); Colletotrichum pleopeltidis on leaves of Pleopeltis sp. (South Africa); Coniochaeta deborreae from soil (Netherlands); Diaporthe durionigena on branches of Durio zibethinus (Vietnam); Floricola juncicola on dead culm of Juncus sp. (France); Haudseptoria typhae on leaf sheath of Typha sp. (Germany); Hogelandia lambearum from soil (Netherlands); Lomentospora valparaisensis from soil (Chile); Neofusicoccum mystacidii on dead stems of Mystacidium capense (South Africa); Neomycosphaerella guibourtiae on leaves of Guibourtia sp. (Angola); Niesslia neoexosporioides on dead leaves of Carex paniculata (Germany); Nothoanungitopsis urophyllae on seed capsules of Eucalyptus urophylla (South Africa); Nothomicrosphaeropsis welwitschiae on dead leaves of Welwitschia mirabilis (Namibia); Paracremonium bendijkiorum from soil (Netherlands); Paraphoma ledniceana on dead wood of Buxus sempervirens (Czech Republic); Paraphoma salicis on leaves of Salix cf. alba (Ukraine); Parasarocladium wereldwijsianum from soil (Netherlands); Peziza ligni on masonry and plastering (France); Phyllosticta phoenicis on leaves of Phoenix reclinata (South Africa); Plectosphaerella slobbergiarum from soil (Netherlands); Populomyces zwinianus from soil (Netherlands); Pseudoacrospermum goniomae on leaves of Gonioma kamassi (South Africa); Pseudopyricularia festucae on leaves of Festuca californica (USA); Sarocladium sasijaorum from soil (Netherlands); Sporothrix hypoxyli in sporocarp of Hypoxylon petriniae on Fraxinus wood (Netherlands); Superstratomyces albomucosus on Pycnanthus angolensis (Netherlands); Superstratomyces atroviridis on Pinus sylvestris (Netherlands); Superstratomyces flavomucosus on leaf of Hakea multilinearis (Australia); Superstratomyces tardicrescens from human eye specimen (USA); Taeniolella platani on twig of Platanus hispanica (Germany), and Tympanis pini on twigs of Pinus sylvestris (Spain). Citation: Crous PW, Hernández-Restrepo M, Schumacher RK, Cowan DA, Maggs-Kölling G, Marais E, Wingfield MJ, Yilmaz N, Adan OCG, Akulov A, Álvarez Duarte E, Berraf-Tebbal A, Bulgakov TS, Carnegie AJ, de Beer ZW, Decock C, Dijksterhuis J, Duong TA, Eichmeier A, Hien LT, Houbraken JAMP, Khanh TN, Liem NV, Lombard L, Lutzoni FM, Miadlikowska JM, Nel WJ, Pascoe IG, Roets F, Roux J, Samson RA, Shen M, Spetik M, Thangavel R, Thanh HM, Thao LD, van Nieuwenhuijzen EJ, Zhang JQ, Zhang Y, Zhao LL, Groenewald JZ (2021). New and Interesting Fungi. 4. Fungal Systematics and Evolution 7: 255-343. doi: 10.3114/fuse.2021.07.13.

One-Dimensional NMR Imaging of High-Temperature First-Drying in Monolithics.

In this study a specialized high-temperature nuclear magnetic resonance (NMR) setup is presented for measuring free moisture in monolithic refractory castables during one-sided heating (100-300 °C). This setup makes use of a high thermal-stability Birdcage-coil for measuring the quantitative moisture content at high-temperatures, while also utilizing a mini-coil for calibrating transverse relaxation changes, as a function of temperature and hydration state, taking place in the sample throughout a drying experiment. We employ a high-temperature correction scheme that calibrates the effects of rising temperatures on the NMR signal. With this configuration, we can non-destructively measure moisture and temperature profiles continuously and achieve a spatial resolution of 2-3 mm for samples as long as 74 mm. After applying the NMR correction, we can extract information about the physical and chemical components of water as they are released from the porous matrix during first heat up. As a model material, we demonstrate the capability of our setup with a conventional castable after it has been cast and cured for 48 h.

Nano-particle dynamics during capillary suction.

Due to the increased use of nanoparticles in everyday applications, there is a need for theoretical descriptions of particle transport and attachment in porous media. It should be possible to develop a one dimensional model to describe nanoparticle retention during capillary transport of liquid mixtures in porous media. Water-glycerol-nanoparticle mixtures were prepared and the penetration process in porous Al2O3 samples of varying pore size is measured using NMR imaging. The liquid and particle front can be measured by utilizing T2 relaxation effects from the paramagnetic nanoparticles. A good agreement between experimental data and the predicted particle retention by the developed theory is found. Using the model, the binding constant for Fe2O3 nanoparticles on sintered Al2O3 samples and the maximum surface coverage are determined. Furthermore, we show that the penetrating liquid front follows a square root of time behavior as predicted by Darcy's law. However, scaling with the liquid parameters is no longer sufficient to map different liquid mixtures onto a single master curve. The Darcy model should be extended to address the two formed domains (with and without particles) and their interaction, to give an accurate prediction for the penetrating liquid front.

Wood staining fungi revealed taxonomic novelties in Pezizomycotina: New order Superstratomycetales and new species Cyanodermella oleoligni.

A culture-based survey of staining fungi on oil-treated timber after outdoor exposure in Australia and the Netherlands uncovered new taxa in Pezizomycotina. Their taxonomic novelty was confirmed by phylogenetic analyses of multi-locus sequences (ITS, nrSSU, nrLSU, mitSSU, RPB1, RPB2, and EF-1α) using multiple reference data sets. These previously unknown taxa are recognised as part of a new order (Superstratomycetales) potentially closely related to Trypetheliales (Dothideomycetes), and as a new species of Cyanodermella, C. oleoligni in Stictidaceae (Ostropales) part of the mostly lichenised class Lecanoromycetes. Within Superstratomycetales a single genus named Superstratomyces with three putative species: S. flavomucosus, S. atroviridis, and S. albomucosus are formally described. Monophyly of each circumscribed Superstratomyces species was highly supported and the intraspecific genetic variation was substantially lower than interspecific differences detected among species based on the ITS, nrLSU, and EF-1α loci. Ribosomal loci for all members of Superstratomyces were noticeably different from all fungal sequences available in GenBank. All strains from this genus grow slowly in culture, have darkly pigmented mycelia and produce pycnidia. The strains of C. oleoligni form green colonies with slimy masses and develop green pycnidia on oatmeal agar. These new taxa could not be classified reliably at the class and lower taxonomic ranks by sequencing from the substrate directly or based solely on culture-dependent morphological investigations. Coupling phenotypic observations with multi-locus sequencing of fungi isolated in culture enabled these taxonomic discoveries. Outdoor situated timber provides a great potential for culturable undescribed fungal taxa, including higher rank lineages as revealed by this study, and therefore, should be further explored.

Production of an extracellular matrix as an isotropic growth phase of Penicillium rubens on gypsum.

Indoor mold represents an important environmental concern, but a fundamental knowledge of fungal growth stages is needed to limit indoor fungal proliferation on finishing materials used in buildings. The present study focused on the succession of germination stages of the common indoor fungus Penicillium rubens on a gypsum substrate. This substrate is used as a model system representing porous materials that are widely used in indoor environments. Imaging with cryo-scanning electron microscopy showed that the formation of an extracellular matrix (ECM) is a phase of the isotropic growth of P. rubens that is uniquely related to germinating conidia. Furthermore, the ECM is observed only when a dry-state inoculation of the surface is applied, i.e., applying conidia directly from a 7-day-old colony, mimicking airborne contamination of the surface. When inoculation is done by spraying an aqueous conidial suspension, no ECM is observed. Moreover, it is concluded that the formation of an ECM requires active processes in the fungal cell. The porosity of the substrate proved that the ECM substance has high-viscosity characteristics. The present results stress that studies of indoor fungal growth should consider the method of inoculation, knowing that the common aqueous suspension may obscure specific stages in the initial phases of germination.

Morphology, binding behavior and MR-properties of paramagnetic collagen-binding liposomes.

Collagen is an important component of the extracellular matrix (ECM) and plays an important role in normal tissue maturation and in pathological processes such as atherosclerosis and myocardial infarction. The diagnostics of the latter diseases using MRI could strongly benefit from the use of collagen-specific contrast agents. The current study aimed to develop a bimodal liposomal MR contrast agent that was functionalized with CNA35, a collagen adhesion protein of the Staphylococcus aureus bacterium. The liposomes were characterized in terms of CNA35 protein conjugation and loading. The overall morphology was assessed with DLS and cryo-TEM, while cryo-TEM tomography was used to visualize the protein coverage of the liposomes. The binding properties of the contrast agent were investigated using a fluorescence assay based on the rhodamine content of the liposomes. The bulk relaxivity was determined using regular relaxometry while the MR-properties of liposomes in their bound state were studied using NMR depth profiling. This CNA35 functionalized contrast agent and the set of in vitro experiments we performed indicate the potential of this technology for in vivo molecular imaging of collagen.

High-resolution NMR imaging of paramagnetic liposomes targeted to a functionalized surface.

A major application of molecular MR imaging is receptor mapping of cells lining blood vessels with targeted contrast agents. Since these agents accumulate at interfaces, knowledge of their influence on the relaxation process in this specific configuration is a prerequisite for understanding their working principle. A methodology is presented to study the influence of targeted contrast agents on surface relaxation in vitro. Paramagnetic liposomes attached to a functionalized surface were studied with high-resolution NMR imaging. The surface was prepared by covering a solid substrate with a layer of collagen. Paramagnetic liposomes were targeted to this surface by functionalizing the liposomes with collagen adhesion protein CNA-35. With a saturation-recovery sequence, 1D magnetization profiles with a resolution of 5 microm were measured in water in contact with the surface. Analytical predictions, obtained with the Bloch-Torrey equation, perfectly agreed with the experimental data. Therefore, the magnitude of the surface relaxation rate could be determined from the measurements without any assumption. By using the relaxivity of liposome solutions the surface coverage by liposomes could be estimated. With the presented methodology the behavior of Gd-based targeted contrast agents at biological interfaces can be studied in vitro. Their influence on relaxation processes can be characterized and quantified.