Artificial neural network modeling for the oxidation kinetics of divalent manganese ions during chlorination and the role of arsenite ions in the binary/ternary systems.

This study investigated the coexistence and contamination of manganese (Mn(II)) and arsenite (As(III)) in groundwater and examined their oxidation behavior under different equilibrating parameters, including varying pH, bicarbonate (HCO3-) concentrations, and sodium hypochlorite (NaClO) oxidant concentrations. Results showed that if the molar ratio of NaClO: As(III) was >1, the oxidation of As(III) could be achieved within a minute with an extremely high oxidation rate of 99.7 %. In the binary system, the removal of As(III) prevailed over Mn(II). The As(III) oxidation efficiency increased from 59.8 ± 0.6 % to 70.8 ± 1.9 % when pH rose from 5.7 to 8.0. The oxidation reaction between As(III) and NaClO releases H+ ions, decreasing the pH from 6.77 to 6.19 and reducing the removal efficiency of Mn(II). The presence of HCO3- reduced the oxidation rate of Mn(II) from 63.2 % to 13.9 % within four hours. Instead, the final oxidation rate of Mn(II) increased from 68.1 % to 87.7 %. This increase can be attributed to HCO3- ions competing with the free Mn(II) for the adsorption sites on the sediments, inhibiting the formation of H+. Moreover, kinetic studies revealed that the oxidation reaction between Mn(II) and NaClO followed first-order kinetics based on their R2 values. The significant factors affecting the Mn(II) oxidation efficiency were the initial concentration of NaClO and pH. Applying an artificial neural network (ANN) model for data analysis proved to be an effective tool for predicting Mn(II) oxidation rates under different experimental conditions. The actual Mn(II) oxidation data and the predicted values obtained from the ANN model showed significant consistency. The training and validation data sets yielded R2 values of 0.995 and 0.992, respectively. Moreover, the ANN model highlights the importance of pH and NaClO concentrations in influencing the oxidation rate of Mn(II).

Assessment of effectiveness in stabilization/solidification of arsenic-contaminated soil: long-term leaching test and geophysical measurement.

This study focused on evaluating the effectiveness of stabilizer/binding agents in immobilizing arsenic (As) in contaminated soil using both geochemical and geophysical monitoring methods. The effluent from the stabilizer/binding agent's application and control columns was analyzed, and the status of the columns was monitored using electrical resistivity (ER) and induced polarization (IP) methods. As stabilizers/binder, acid mine drainage sludge (AMDS) and steel slag (SS) were used, which delayed As and Ca leaching time and significantly reduced As leaching amount. Determination coefficients for As and Fe leaching exhibited elevated values (control column, R2 = 0.955; AMDS column, R2 = 0.908; and SS column, R2 = 0.833). A discernible decline in the concentration of leached Fe was accompanied by a corresponding reduction in IP. The determination coefficients correlating IP and Fe leaching remained substantial (control column, R2 = 0.768; AMDS column, R2 = 0.807; and SS column, R2 = 0.818). Such IP measurements manifest as instrumental tools in monitoring and assessing the retention capacity of applied stabilizer/binding agents in As-affected soils, thereby furnishing crucial data for the enduring surveillance of stabilization/solidification locales. This research posits a swift and continuous monitoring method for solidification/stabilization locales in situ.

Molecular characterization of azoreductase and its potential for the decolorization of Remazol Red R and Acid Blue 29.

Azoreductase is a reductive enzyme that efficiently biotransformed textile azo dyes. This study demonstrated the heterologous overexpression of the azoreductase gene in Escherichia coli for the effective degradation of Remazol Red-R and Acid-Blue 29 dyes. The AzK gene of Klebsiella pneumoniae encoding a ≈22 kDa azoreductase enzyme was cloned into the pET21+C expression vector. The inoculum size of 1.5%, IPTG concentration of 0.5 mM, and incubation time of 6 h were optimized by response surface methodology a statistical tool. The crude extract showed 76% and 74%, while the purified enzyme achieved 94% and 93% decolorization of RRR and AB-29, respectively in 0.3 h. The reaction kinetics showed that RRR had a Km and Vmax value of 0.058 mM and 1416 U mg-1, respectively at an NADH concentration of 10 mM. HPLC and GC-MS analyses showed that RRR was effectively bio-transformed by azoreductase to 2-[3-(hydroxy-amino) benzene-1-sulfonyl and AB-29 to aniline and 3-nitrosoaniline. This study explored the potential of recombinant azoreductase isolated from K. pneumoniae in the degradation of toxic textile azo dyes into less toxic metabolites.

Polyol-mediated zinc oxide nanoparticles using the refluxing method as an efficient photocatalytic and antimicrobial agent.

Nanomaterials have attracted more curiosity recently because of their wide-ranging application in environmental remediation and electronic devices. The current study focuses on zinc oxide nanoparticles' (ZnO NPs) simple production, characterization, and applications in several fields, including medicinal and photocatalytic degradation of dyes. The non-aqueous-based reflux method is helpful for ZnO NP synthesis; the procedure involves refluxing zinc acetate dihydrate precursor in ethylene glycol for 3 hours in the absence of sodium acetate, in which the refluxing rate and the cooling rate are optimized to get the desired phase, and the unique morphology of polyol-mediated ZnO NPs; it has been achieved using the capping agent TBAB (tetra-butyl ammonium bromide) and precursor zinc acetate dihydrate. UV-Vis, FTIR, XRD, and FESEM structurally characterized polyol-mediated ZnO-NPs. The results show that the material is pure and broadly aggregated into spherical nanoparticles with an average particle size of 18.09 nm. According to XRD analysis, heat annealing made the crystallites more prominent and favored a monocrystalline state. These results and the low cost of making polyol-mediated ZnO NPs demonstrate photocatalytic and antimicrobial properties.

Fate of five bisphenol derivatives in Chlamydomonas mexicana: Toxicity, removal, biotransformation and microalgal metabolism.

Bisphenols (BPs) are recognized as emerging contaminants because of their estrogenic properties and frequent occurrence in environmental matrices. Here, we evaluated the toxic effects of five common BPs on freshwater microalga Chlamydomonas mexicana and removal of the BPs by the alga. Bisphenols -AF (BPAF), -B (BPB), and -Z (BPZ) (96 h, EC50 1.78-12.09 mg·L-1) exhibited higher toxicity to C. mexicana compared to bisphenol -S (BPS) and -F (BPF) (96 h, EC50 30.53-85.48 mg·L-1). In contrast, the mixture of BPs exhibited acute toxicity (96 h, EC50 8.07 mg·L-1). After 14 days, C. mexicana had effectively removed 61%, 99%, 55%, 87%, and 89% of BPS, BPF, BPAF, BPB, and BPZ, respectively, at 1 mg L-1. The biotransformed products of all five BPs were analyzed using UHPLC QTOF, and their toxicity was predicted. All biotransformed products were observed to be less toxic than the parent compounds. The fatty acid composition of C. mexicana after exposure to the BP mixture was predominantly palmitic acid (34.14%), followed by oleic acid (18.9%), and γ-linolenic acid (10.79%). The results provide crucial information on the ecotoxicity of these five BPs and their removal by C. mexicana; the resulting biomass is a potential feedstock for producing biodiesel.

Fluoride occurrence in environment, regulations, and remediation methods for soil: A comprehensive review.

Fluoride, a naturally occurring chemical element, is largely insoluble in soils. More than 90% of the fluoride in soil is bound to soil particles and is unable to be dissolved. As part of the soil, fluoride is predominantly located in the colloid or clay fraction of the soil, and the movement of fluoride is strongly affected by the sorption capacity of the soil, which is affected by pH, the type of soil sorbent present, and the salinity. The Canadian Council of Ministers of the Environment soil quality guideline for fluoride in soils under a residential/parkland land use scenario is 400 mg/kg. In this review, we focus on fluoride contamination in soil and subsurface environments, and the various sources of fluorides are discussed in detail. The average fluoride concentration in soil in different countries and their regulations for soil and water are comprehensively reviewed. In this article, the latest advances in defluoridation methods are highlighted and the importance of further research addressing efficient and cost-effective methods to remediate fluoride contamination in soil is critically discussed. Methods used to mitigate fluoride risks by removing fluoride from the soil are presented. We strongly recommend that regulators and soil chemists in all countries explore opportunities to improve defluoridation methods and consider adopting more stringent regulations for fluoride in soil depending on geologic conditions.

Morphology and stability of mineralized carbon influenced by magnesium ions.

Ex situ mineralization of CO2 is a promising technology that employs Ca- and Mg-rich industrial wastes but it simultaneously produces end products. Although Mg is a major mineralization source, it can adversely impact carbonate precipitation and crystal stability during co-precipitation in combination with Ca2+. In this study, the effects of Mg2+ ions on the mineralization process and its products were investigated using precipitates formed at different aqueous concentrations of Mg2+. The final phases of the precipitates were quantitatively evaluated at the end of each process. The alterations undergone by the calcite crystals, which constituted the dominant carbonate phase in each experiment, were analyzed using a sophisticated crystallographic approach. Aragonite was detected at high Mg2+ concentrations (Mg2+/Ca2+ ratio of 2.00), although brucite was the sole phase of the Mg crystal. The increase in Mg2+ ion concentration induced the formation of an amorphous solid. The results revealed that a drastic transformation of the calcite lattice occurred when the ratio of Mg2+/Ca2+ exceeded 1.00, agreeing with the shifts observed in the calcite structure upon comparing the precipitates formed at the Mg2+/Ca2+ ratios of 1.00 and 2.00, wherein microstrain and crystallite sizes changed from 0.040 and 55.33 nm to 0.1533 and 12.35 nm, respectively. At a Mg2+/Ca2+ ratio of 2.00, 6.51% of the Ca2+ ions in the calcite structure were substituted by Mg2+, increasing the surface energy of the crystal and the solubility of the carbonate. Therefore, Mg2+ is a potential hindrance that can impede the precipitation of carbonates and increase instability at certain concentrations.

Evaluation of pyrite/sodium hypochlorite for activating purification of arsenic from fractured-bedrock groundwater.

In this work, the effectiveness of pyrite/sodium hypochlorite (FeS2/NaClO) treatment to eliminate arsenic (As) from fractured-bedrock groundwater via oxidative adsorption was evaluated. The As concentration in the tested reactors decreased sharply during the initial 5 min, as the addition of NaClO effectively increased the As removal efficiency, attaining 98.6% removal within 60 min in the presence of 0.05 M NaClO. There was no coexisting anion effect (Cl-, CO3-, HCO3-, NO3-, and F-) on the As removal capacity of FeS2/NaClO, except for the PO43- which resulted in less removal of As. X-ray spectroscopy analysis of As(III)-sorbed FeS2 surfaces revealed that a portion of As(III) was oxidized into As(V) during the adsorption process. Scanning electron microscopy-energy-dispersive spectrometer results of FeS2 exhibited the distribution of adsorbed As on the newly formed iron (oxy) hydroxide surfaces, with an As element ratio of 1.27%. A continuous flow-bed column study further demonstrated the efficiency of FeS2/NaClO treatment to lower the contamination level of As at the removal rates of 0.66-3.02 mg/L·day for 160 h. These results suggest that FeS2/NaClO treatment can be considered an effective strategy for removing As in groundwater of bedrock aquifers.

Green synthesis of metalloid nanoparticles and its biological applications: A review.

Synthesis of metalloid nanoparticles using biological-based fabrication has become an efficient alternative surpassing the existing physical and chemical approaches because there is a need for developing safer, more reliable, cleaner, and more eco-friendly methods for their preparation. Over the last few years, the biosynthesis of metalloid nanoparticles using biological materials has received increased attention due to its pharmaceutical, biomedical, and environmental applications. Biosynthesis using bacterial, fungal, and plant agents has appeared as a faster developing domain in bio-based nanotechnology globally along with other biological entities, thus posing as an option for conventional physical as well as chemical methods. These agents can efficiently produce environment-friendly nanoparticles with the desired composition, morphology (shape as well as size), and stability, along with homogeneity. Besides this, metalloid nanoparticles possess various applications like antibacterial by damaging bacterial cell membranes, anticancer due to damaging tumour sites, targeted drug delivery, drug testing, and diagnostic roles. This review summarizes the various studies associated with the biosynthesis of metalloid particles, namely, tellurium, arsenic, silicon, boron, and antimony, along with their therapeutic, pharmaceutical and environmental applications.

Integrative biohydrogen- and biomethane-producing bioprocesses for comprehensive production of biohythane.

The production of biohythane, a combination of energy-dense hydrogen and methane, from the anaerobic digestion of low-cost organic wastes has attracted attention as a potential candidate for the transition to a sustainable circular economy. Substantial research has been initiated to upscale the process engineering to establish a hythane-based economy by addressing major challenges associated with the process and product upgrading. This review provides an overview of the feasibility of biohythane production in various anaerobic digestion systems (single-stage, dual-stage) and possible technologies to upgrade biohythane to hydrogen-enriched renewable natural gas. The main goal of this review is to promote research in biohythane production technology by outlining critical needs, including meta-omics and metabolic engineering approaches for the advancements in biohythane production technology.

The comprehensive effects of aluminum oxide nanoparticles on the physiology of freshwater microalga Scenedesmus obliquus and it's phycoremediation performance for the removal of sulfacetamide.

Nanoparticles are inevitable byproducts of modern industry. However, the environmental impacts arising from industrial applications of nanoparticles are largely under-reported. This study evaluated the ecotoxicological effects of aluminum oxide nanoparticles (Al2O3NP) and its influence on sulfacetamide (SA) biodegradation by a freshwater microalga, Scenedesmus obliquus. Although Al2O3NP showed limited toxicity effect on S. obliquus, we observed the toxicity attenuation aspect of Al2O3NP in a mixture of sulfacetamide on microalgae. The addition of 100 mg L-1 of Al2O3NP and 1 mg L-1 of SA reduced total chlorophyll by 23.3% and carotenoids by 21.6% in microalgal compared to control. The gene expression study demonstrated that ATPF0C, Lhcb1, HydA, and psbA genes responsible for ATP synthesis and the photosynthetic system were significantly downregulated, while the Tas gene, which plays a major role in biodegradation of organic xenobiotic chemicals, was significantly upregulated at 1 and 100 mg L-1 of Al2O3NP. The S. obliquus removed 16.8% of SA at 15 mg L-1 in 14 days. However, the removal was slightly enhanced (18.8%) at same concentration of SA in the presence of 50 mg L-1 Al2O3NP. This result proves the stability of sulfacetamide biodegradation capacity of S. obliquus in the presence of Al2O3NP co-contamination. The metabolic analysis showed that SA was degraded into simpler byproducts such as sulfacarbamide, sulfaguanidine, sulfanilamide, 4-(methyl sulfonyl)aniline, and N-hydroxy-benzenamine which have lower ecotoxicity than SA, demonstrating that the ecotoxicity of sulfacetamide has significantly decreased after the microalgal degradation, suggesting the environmental feasibility of microalgae-mediated wastewater technology. This study provides a deeper understanding of the impact of nanoparticles such as Al2O3NP on aquatic ecosystems.

Effect of Fuel Preheating on Engine Characteristics of Waste Animal Fat-Oil Biodiesel in Compression Ignition Engine.

The present study aims at understanding the effects of fuel preheating on engine characteristics of waste animal fat-oil (WAF-O) biodiesel in a single-cylinder CI engine, with the preheating technique proposed as an effective means for enhancing the fuel properties. To understand the effects of the preheated fuel, the WAF-O biodiesel was preheated at 60, 80, 100 and 120 °C and tested along with neat diesel and unheated WAF-O biodiesel. For this purpose, biodiesel was produced from different animal wastes by means of KOH-assisted ethanol-based transesterification, reporting its maximum yield as 96.37 ± 1.8%, with significant distribution of unsaturated oleic acid, saturated palmitic acid and stearic acid. Upon evaluating its fuel characteristics as per ASTM D6751 standards, a rise in preheating temperature by 1 °C reduced the density and kinematic viscosity of WAF-O biodiesel by 0.383 kg/m3 and 0.025 mm2/s, respectively, and was explained by the weakening of intermolecular forces between its fatty acid ester molecules. Preheated samples reported superior combustion characteristics by exhibiting increased in-cylinder pressure (2.24%, on average) and heat release rates in addition to their shortened ignition delay (1−4 °CA). Furthermore, preheating of WAF-O biodiesel reduced its specific fuel consumption and increased its brake thermal efficiency by 7.86% (on average) and 9.23% (on average), respectively. However, higher preheating temperatures (>120 °C) resulted in increased fuel consumption owing to its varied flow characteristics. In addition to the changes in combustion characteristics, preheating WAF-O bio-diesel also resulted in reduced carbon monoxide, nitrous oxide and hydrocarbon emission by 13.88%, 7.21% and 26.94%, respectively, and increased carbon dioxide emission by 7.58%. Summing up, the enhancements in overall engine characteristics of preheated samples were accounted for by their improvised fuel injection characteristics due to their reduced density and viscosity, which ensured for their effective combustion.

Marine Alga Ulva fasciata-Derived Molecules for the Potential Treatment of SARS-CoV-2: An In Silico Approach.

SARS-CoV-2 is the causative agent of the COVID-19 pandemic. This in silico study aimed to elucidate therapeutic efficacies against SARS-CoV-2 of phyco-compounds from the seaweed, Ulva fasciata. Twelve phyco-compounds were isolated and toxicity was analyzed by VEGA QSAR. Five compounds were found to be nonmutagenic, noncarcinogenic and nontoxic. Moreover, antiviral activity was evaluated by PASS. Binding affinities of five of these therapeutic compounds were predicted to possess probable biological activity. Fifteen SARS-CoV-2 target proteins were analyzed by the AutoDock Vina program for molecular docking binding energy analysis and the 6Y84 protein was determined to possess optimal binding affinities. The Desmond program from Schrödinger's suite was used to study high performance molecular dynamic simulation properties for 3,7,11,15-Tetramethyl-2-hexadecen-1-ol-6Y84 for better drug evaluation. The ligand with 6Y84 had stronger binding affinities (-5.9 kcal/mol) over two standard drugs, Chloroquine (-5.6 kcal/mol) and Interferon α-2b (-3.8 kcal/mol). Swiss ADME calculated physicochemical/lipophilicity/water solubility/pharmacokinetic properties for 3,7,11,15-Tetramethyl-2-hexadecen-1-ol, showing that this therapeutic agent may be effective against SARS-CoV-2.

A Promising Review on Cyclodextrin Conjugated Paclitaxel Nanoparticles for Cancer Treatment.

This review presented the unique characteristics of different types of cyclodextrin polymers by non-covalent host-guest interactions to synthesize an inclusion complex. Various cancers are treated with different types of modified cyclodextrins, along with the anticancer drug paclitaxel. PTX acts as a mitotic inhibitor, but due to its low dissolution and permeability in aqueous solutions, it causes considerable challenges for drug delivery system (DDS) designs. To enhance the solubility, it is reformulated with derivatives of cyclodextrins using freeze-drying and co-solvent lyophilization methods. The present supramolecular assemblies involve cyclodextrin as a key mediator, which is encapsulated with paclitaxel and their controlled release at the targeted area is highlighted using different DDS. In addition, the application of cyclodextrins in cancer treatment, which reduces the off-target effects, is briefly demonstrated using various types of cancer cell lines. A new nano-formulation of PTX is used to improve the antitumor activity compared to normal PTX DDS in lungs and breast cancer is well defined in the present review.

Syntrophic bacteria- and Methanosarcina-rich acclimatized microbiota with better carbohydrate metabolism enhances biomethanation of fractionated lignocellulosic biocomponents.

An inadequate lignocellulolytic capacity of a conventional anaerobic digester sludge (ADS) microbiota is the bottleneck for the maximal utilization of lignocellulose in anaerobic digestion. A well-constructed microbial consortium acclimatized to lignocellulose outperformed the ADS in terms of biogas productivity when fractionated biocomponents of rice straw were used to achieve a high methane bioconversion rate. A 33.3 % higher methane yield was obtained with the acclimatized consortium (AC) compared to that of ADS control. The dominant pair-wise link between Firmicutes (18.99-40.03 %), Bacteroidota (10.94-28.75 %), and archaeal Halobacteriota (3.59-20.57 %) phyla in the AC seed digesters indicated that the keystone members of these phyla were responsible for higher methane yield. A high abundance of syntrophic bacteria such as Proteiniphilum (1.22-5.19 %), Fermentimonas (0.71-5.31 %), Syntrophomonas (0.87-3.59 %), and their syntrophic partner Methanosarcina (4.26-18.80 %) maintained the digester stability and facilitated higher substrate-to-methane conversion in the AC seed digesters. The present combined strategy will help in boosting the 'biomass-to-methane" conversion.

Nanostructured Antibiotics and Their Emerging Medicinal Applications: An Overview of Nanoantibiotics.

Bacterial strains resistant to antimicrobial treatments, such as antibiotics, have emerged as serious clinical problems, necessitating the development of novel bactericidal materials. Nanostructures with particle sizes ranging from 1 to 100 nanometers have appeared recently as novel antibacterial agents, which are also known as "nanoantibiotics". Nanomaterials have been shown to exert greater antibacterial effects on Gram-positive and Gram-negative bacteria across several studies. Antibacterial nanofilms for medical implants and restorative matters to prevent bacterial harm and antibacterial vaccinations to control bacterial infections are examples of nanoparticle applications in the biomedical sectors. The development of unique nanostructures, such as nanocrystals and nanostructured materials, is an exciting step in alternative efforts to manage microorganisms because these materials provide disrupted antibacterial effects, including better biocompatibility, as opposed to minor molecular antimicrobial systems, which have short-term functions and are poisonous. Although the mechanism of action of nanoparticles (NPs) is unknown, scientific suggestions include the oxidative-reductive phenomenon, reactive ionic metals, and reactive oxygen species (ROS). Many synchronized gene transformations in the same bacterial cell are essential for antibacterial resistance to emerge; thus, bacterial cells find it difficult to build resistance to nanoparticles. Therefore, nanomaterials are considered as advanced solution tools for the fields of medical science and allied health science. The current review emphasizes the importance of nanoparticles and various nanosized materials as antimicrobial agents based on their size, nature, etc.

Metabolome and transcriptome analyses of plants grown in naturally attenuated soil after hydrogen fluoride exposure.

Accidental chemical leaks and illegal chemical discharges are a global environmental issue. In 2012, a hydrogen fluoride leak in Gumi, South Korea, killed several people and contaminated the environment. This leak also led to a significant decline in crop yield, even after the soil concentration of hydrogen fluoride decreased to below the standard level following natural attenuation. To determine the cause of this decreased plant productivity, we designed direct and indirect exposure tests by evaluating the metabolome, transcriptome, and phenome of the plants. In an indirect exposure test, soil metabolomics revealed downregulation of metabolites in vitamin B6, lipopolysaccharide, osmolyte, and exopolysaccharide metabolism. Next-generation sequencing of the plants showed that ABR1 and DREB1A were overexpressed in response to stress. Plant metabolomics demonstrated upregulation of folate biosynthesis and nicotinate and nicotinamide metabolism associated with detoxification of reactive oxygen species. These results demonstrate impaired metabolism of soil microbes and plants even after natural attenuation of hydrogen fluoride in soil. The novel chemical exposure testing used in this study can be applied to identify hidden damage to organisms after natural attenuation of chemicals in soil, as well as biomarkers for explaining the decline in yield of plants grown in soil near pollutant-emitting industrial facilities.

Feasibility assessment of bioethanol production from humic acid-assisted alkaline pretreated Kentucky bluegrass (Poa pratensis L.) followed by downstream enrichment using direct contact membrane distillation.

The effective fractionation of structural components of abundantly available lignocellulosic biomass is essential to unlock its full biorefinery potential. In this study, the feasibility of humic acid on the pretreatment of Kentucky bluegrass biomass in alkaline condition was assessed to separate 70.1% lignin and hydrolyzable biocomponents. The humic acid-assisted delignification followed by enzymatic saccharification yielded 0.55 g/g of reducing sugars from 7.5% (w/v) pretreated biomass loading and 16 FPU/g of cellulase. Yeast fermentation of the biomass hydrolysate produced 76.6% (w/w) ethanol, which was subsequently separated and concentrated using direct contact membrane distillation. The hydrophobic microporous flat-sheet membrane housed in a rectangular-shaped crossflow module and counter-current mode of flow of the feed (hot) and distillate (cold) streams yielded a flux of 11.6 kg EtOH/m2/24 h. A modular, compact, flexible, and eco-friendly membrane-integrated hybrid approach is used for the first time to effectively valorize Kentucky bluegrass biomass for sustainable production of biofuel.

Biodiesel production potential of microalgae, cultivated in acid mine drainage and livestock wastewater.

The adaptability and biofuel production potential of two strains of microalgae isolated and cultivated in livestock wastewater effluent (LWE) with acid mine drainage (AMD) were investigated. The isolated strains of microalgae from samples obtained from LWE and AMD, two microalgal strains (Nephroselmis sp. KGE2 and Autodesmus obliquus KGE17) were selected based on their growth rate and lipid productivity. The dry cell weight of Nephroselmis sp. KGE2 and Autodesmus obliquus KGE17 after 20 days of cultivation in AMD increased from 0.05 to 0.59 g/L and from 0.05 to 0.55 g/L, respectively. These findings revealed a significant accumulation of fatty acids with increasing AMD content. Nephroselmis sp. KGE2 in LWE with 5% AMD demonstrated a higher growth rate (0.59 ± 0.03 g/L) and fatty acid production (401.5 ± 47.3 mg/L) than Autodesmus obliquus KGE17 with 5% AMD. Additionally, Nephroselmis sp. KGE2 had C16-C18 fatty acid content (92.4%) in LWE with AMD. Biodiesel produced from Nephroselmis sp. KGE2 had a higher cetane number (52.31) and iodine value (88.26 g I2/100 g oil). Consequently, Nephroselmis sp. KGE2 can be considered a potential candidate for biodiesel production using AMD as an iron source.

Lignocellulolytic microbiomes for augmenting lignocellulose degradation in anaerobic digestion.

Bioaugmenting lignocellulose digestion with potent lignocellulolytic microbiomes (LMs) facilitates efficient biomethanation. Assessing the metabolic roles of microbial communities of the LMs and their complex interactions with the indigenous anaerobic digester microbiome is pivotal in implementing bioaugmentation. Multiple meta-omics are the frontline approaches to investigating gene functions, metabolic roles, and the ecological niches of LMs.