Remineralizing pretreatment using casein phosphopeptide-amorphous calcium phosphate fluoride, self-assembling peptide, and nanohydroxyapatite gel activation via invisible infrared light on the dentin microhardness and micro shear bond strength to the composite restoration.

AIM: Different remineralizing pretreatments Casein phosphopeptide-amorphous calcium phosphate fluoride (CPP-ACPF), tricalcium phosphate fluoride (TCP-F), self-assembling peptide (SAP) P11-4 and 10 % Nanohydroxyapatite (nHA) gel activation via invisible infrared light on the dentin microhardness (MH) and micro shear bond strength (µSBS) of composite restoration. METHODS: Seventy-five human molar teeth were collected and the dentinal surface of all the samples was exposed to different demineralizing solutions. (n = 15) Group 1 (demineralized dentin), Group 2 (CPP ACP), Group 3 (TCP-F), Group 4 (SAP P11-4), Group 5 (nHA gel activation via invisible infrared light). MH assessment was performed using Vickers hardness. Each group of 10 samples was subjected to composite restoration buildup and µSBS were tested. The debonded samples were then observed under a stereo-microscope for failure analysis. ANOVA was conducted, along with Tukey's post hoc analysis, to examine the µSBS of composite and MH of the remineralized surface. RESULTS: nHA gel activation via invisible infrared light pretreated specimens showed the maximum outcomes of surface hardness (331.2 ± 77.3) and bond strength (10.38 ± 2.77). However, Group 4 (SAP P11-4) (148.3 ± 29.2) remineralized dentin displayed minimum scores of MH and µSBS (5.88 ± 1.01). CONCLUSION: Remineralizing pretreatment nHA gel activation via invisible infrared light and casein phosphopeptide-amorphous calcium phosphate fluoride seem to improve the dentin MH and µSBS of the composite restoration.

Analysis of recurrent esthetic dental proportion of natural maxillary anterior teeth: A systematic review.

STATEMENT OF PROBLEM: The recurrent esthetic dental (RED) proportion has been a benchmark for the rehabilitation of the maxillary anterior teeth of North American patients. While it has been evaluated in other populations, the global application of RED proportions in the rehabilitation of maxillary anterior teeth is unclear. PURPOSE: The purpose of this systematic review was to examine the existing evidence on dental proportion to evaluate the existence of RED proportions in the esthetic smile in different geographic regions. MATERIAL AND METHODS: A systematic search was conducted by reviewing different databases. The focused question was "Does RED proportion exist in esthetically pleasing smiles in different populations around the world?" The search included articles with a combination of MeSH keywords based on dental proportion from January 2000 to July 2020. The titles and abstracts were identified by using a search protocol. Full text of the articles was independently evaluated. The systematic review was modified to summarize the relevant data. The general characteristics, outcomes, and quality of studies were reviewed and analyzed systematically. RESULTS: Seventeen studies were selected from the reviewed articles. Three studies were conducted in Europe, 10 in South Asia, and 4 in Western Asia. Eleven studies found that the mean perceived ratio of anterior teeth was not constant when progressing distally. Five studies reported that the ratio was constant in a small percentage of their populations, and 1 suggested that the ratio was constant if it remains between 60% and 80%. The central-to-LI and Ca-to-LI proportion values were not constant. Overall, the Ca-to-LI proportion values were higher than the central-to-LI proportions. CONCLUSIONS: RED proportions were not found in the successive widths of maxillary anterior teeth among the reviewed data from different geographic regions. RED proportions are not the only standard for restoring esthetic smiles worldwide, and anterior tooth proportions differ among populations based on their race and ethnicity.

Influence of Concentration Levels of ß-Tricalcium Phosphate on the Physical Properties of a Dental Adhesive.

Our study assessed the influence of integrating 5% and 10% tricalcium phosphate (ß-TCP-Ca3(PO4)2.) nanoparticles into a dental adhesive on the adhesive's bonding. To evaluate the filler nanoparticles, scanning electron microscopy (SEM), Energy Dispersive X-Ray (EDX) spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and micro-Raman spectroscopy techniques were used. Shear Bond strength (SBS) testing, degree of conversion (DC) analysis, investigation of the adhesive-dentin interface, and biofilm experiments were conducted. The SEM micrographs revealed non-uniform agglomerates, while the EDX demonstrated the existence of oxygen 'O' (24.2%), phosphorus 'P' (17.4%) and calcium 'Ca' (60.1%) in the ß-TCP nanoparticles. The FTIR and micro-Raman spectra indicated characteristic bands for ß-TCP containing materials. The 10 wt.% ß-TCP adhesive presented the highest SBS values (NTC-10 wt.% ß-TCP: 33.55 ± 3.73 MPa, TC-10 wt.% ß-TCP: 30.50 ± 3.25 MPa), followed by the 5 wt.% ß-TCP adhesive (NTC-5 wt.% ß-TCP: 32.37 ± 3.10 MPa, TC-5 wt.% ß-TCP: 27.75 ± 3.15 MPa). Most of the detected failures after bond strength testing were adhesive in nature. The ß-TCP adhesives demonstrated suitable dentin interaction by forming a hybrid layer (with few or no gaps) and resin tags. The ß-TCP adhesives (10 wt.%) revealed lower DC values compared to control. The incorporation of 5 and 10 wt.% concentrations of ß-TCP particles resulted in an increase in SBS values. A linear decline in DC values was witnessed when the nanoparticle concentration was increased. Further research focusing on exploring the influence of higher filler concentrations on adhesive's properties is recommended.

Surface Properties of Polymer Resins Fabricated with Subtractive and Additive Manufacturing Techniques.

This study aimed to compare the surface roughness, hardness, and flexure strength of interim indirect resin restorations fabricated with CAD-CAM (CC), 3D printing (3D), and conventional techniques (CV). Twenty disk (3 mm × Ø10 mm) and ten bar specimens (25 × 2 × 2 mm) were fabricated for the CC, 3D, and CV groups, to be used for surface roughness, micro-hardness, and flexural strength testing using standardized protocol. Three indentations for Vickers micro-hardness (VHN) were performed on each disk and an average was identified for each specimen. Surface micro-roughness (Ra) was calculated in micrometers (µm) using a 3D optical non-contact surface microscope. A three-point bending test with a universal testing machine was utilized for assessing flexural strength. The load was applied at a crosshead speed of 3 mm/min over a distance of 25 mm until fracture. Means and standard deviations were compared using ANOVA and post hoc Tukey-Kramer tests, and a p-value of ≤0.05 was considered statistically significant. Ra was significantly different among the study groups (p < 0.05). Surface roughness among the CC and CV groups was statistically comparable (p > 0.05). However, 3D showed significantly higher Ra compared to CC and CV samples (p < 0.05). Micro-hardness was significantly higher in 3D samples (p < 0.05) compared to CC and CV specimens. In addition, CC and CV showed comparable micro-hardness (p > 0.05). A significant difference in flexural strength was observed among the study groups (p < 0.05). CC and 3D showed comparable strength outcomes (p > 0.05), although CV specimens showed significantly lower (p < 0.05) strength compared to CC and 3D samples. The 3D-printed provisional restorative resins showed flexural strength and micro-hardness comparable to CAD-CAM fabricated specimens, and surface micro-roughness for printed specimens was considerably higher compared to CAD-CAM and conventional fabrication techniques.

Polymer-Based Bioactive Luting Agents for Cementation of All-Ceramic Crowns: An SEM, EDX, Microleakage, Fracture Strength, and Color Stability Study.

The aim of the study was to compare microleakage and fracture loads of all ceramic crowns luted with conventional polymer resins and polymeric bioactive cements and to assess the color stability of polymeric bioactive cements. Seventy-five extracted premolar teeth were tested for fracture loads and microleakage in all-ceramic crowns cemented with two types of polymeric bioactive cements and resin cements. In addition, the degree of color change for each cement with coffee was assessed. Thirty maxillary premolar teeth for fracture loads and thirty mandibular premolar teeth for microleakage were prepared; standardized teeth preparations were performed by a single experienced operator. All prepared specimens were randomly distributed to three groups (n = 20) based on the type of cement, Group 1: resin cement (Multilink N); Group 2: polymeric bioactive cement (ACTIVA); Group 3: polymeric bioactive cement (Ceramir). The cementation procedures for all cements (Multilink, ACTIVA, and Ceramir) were performed according to the manufacturers' instructions. All specimens were aged using thermocycling for 30,000 cycles (5-55 °C, dwell time 30 s). These specimens were tested using the universal testing machine for fracture strength and with a micro-CT for microleakage. For the color stability evaluation, the cement specimens were immersed in coffee and evaluated with a spectrometer. Results: The highest and lowest means for fracture loads were observed in resin cements (49.5 ± 8.85) and Ceramir (39.8 ± 9.16), respectively. Ceramir (2.563 ± 0.71) showed the highest microleakage compared to resin (0.70 ± 0.75) and ACTIVA (0.61 ± 0.56). ACTIVA cements showed comparable fracture loads, microleakage, and stain resistance compared to resin cements.

Influence of TiO2 and ZrO2 Nanoparticles on Adhesive Bond Strength and Viscosity of Dentin Polymer: A Physical and Chemical Evaluation.

The present study aimed to formulate an experimental adhesive (EA) and reinforce it with 5 wt.% titanium dioxide (TiO2) or zirconium oxide (ZrO2) to yield 5% TiO2 and 5% ZrO2 adhesives, respectively, and then analyze the impact of this reinforcement on various mechanical properties of the adhesives. The EA contained a blend of monomers such as bisphenol A glycol dimethacrylate (BisGMA), triethylene glycol dimethacrylate (TEGDMA), 2-hydroxyethyl methacrylate (HEMA), and ethyl 4-dimethylamino benzoate and camphorquinone. The EA included ethyl 4-dimethylamino benzoate and camphorquinone photo-initiators, and diphenyliodonium hexafluorophosphate (DPIHP) was also included to act as an electron initiator. The TiO2 and ZrO2 nanoparticles were incorporated into the EA post-synthesis. To characterize the filler nanoparticles, scanning electron microscopy (SEM) and line-energy dispersive X-ray (EDX) spectroscopy were performed. The adhesives were characterized by analyzing their rheological properties, shear-bond strength (SBS), and interfacial failure types. Further, the resin-dentin interface was also analyzed via SEM. The TiO2 nanoparticles were spherically shaped on the SEM micrographs, while the ZrO2 nanoparticles were seen as non-uniformly shaped agglomerates. The EDX mapping demonstrated the presence of Ti and oxygen for TiO2 and Zr and oxygen for the ZrO2 nanoparticles. Both 5% TiO2 and 5% ZrO2 adhesives revealed decreased viscosity as compared with the EA. The 5% TiO2 adhesive demonstrated higher SBS values for both non-thermocycled (NTC) and thermocycled samples (NTC: 25.35 ± 1.53, TC: 23.89 ± 1.95 MPa), followed by the 5% ZrO2 adhesive group (NTC: 23.10 ± 2.22, TC: 20.72 ± 1.32 MPa). The bulk of the failures (>70%) were of adhesive type in all groups. The SEM analysis of the resin-dentin interface revealed the development of a hybrid layer and resin tags (of variable depth) for the EA and 5% TiO2 groups. However, for the 5% ZrO2 group, the hybrid layer and resin tag establishment appeared compromised. Reinforcement of the EA with TiO2 or ZrO2 caused an increase in the adhesive's SBS (with the 5% TiO2 group demonstrating the highest values) in comparison with the EA (without nanoparticles). However, both nanoparticle-containing adhesives revealed decreased viscosity compared with the EA (without nanoparticles). Further studies investigating the impact of diverse filler concentrations on the properties of adhesives are suggested.