Enhanced photoelectrochemical water splitting by a 3D hierarchical sea urchin-like structure: ZnO nanorod arrays on TiO2hollow hemisphere.

A hierarchical sea urchin-like hybrid metal oxide nanostructure of ZnO nanorods deposited on TiO2porous hollow hemispheres with a thin zinc titanate interface layer is specifically designed and synthesized to form a combined type I straddling and type II staggered junctions. The HHSs, synthesized by electrospinning, facilitate light trapping and scattering. The ZnO nanorods offer a large surface area for improved surface oxidation kinetics. The interface layer of zinc titanate (ZnTiO3) between the TiO2HHSs and ZnO nanorods regulates the charge separation in a closely coupled hierarchy structure of ZnO/ZnTiO3/TiO2. The synergistic effects of the improved light trapping, charge separation, and fast surface reaction kinetics result in a superior photoconversion efficiency of 1.07% for the photoelectrochemical water splitting with an outstanding photocurrent density of 2.8 mA cm-2at 1.23 V versus RHE.

A hybrid mesoporous composite of SnO2 and MgO for adsorption and photocatalytic degradation of anionic dye from a real industrial effluent water.

Water pollution by synthetic anionic dyes is one of the most critical ecological concerns and challenges. Therefore, there is an urgent need to find an efficient adsorbent and photocatalyst for dye removal. In the present study, we aimed to fabricate a hybrid mesoporous composite of spongy sphere-like SnO2 and three-dimensional (3D) cubic-like MgO (SnO2/MgO) as a promising adsorbent/photocatalyst to remove the anionic sunset yellow (SSY) dye from real wastewater at neutral pH conditions. The as-synthesized SnO2 and MgO composite was investigated using XRD, SEM, EDX, TEM, XPS, BET, and zeta potential. The experimental study of the SSY removal using SnO2/MgO composite was performed at different conditions, such as pH, stirring time, dose, and temperature. More than 99% of 10 mg/L SSY was effectively adsorbed from aqueous solution using 40 mg of SnO2/MgO composite at pH 7 and a stirring time of 60 min. The SSY adsorption behavior was well fitted by pseudo-second order and the Langmuir model, indicating that the SSY was chemisorbed to the composite-active sites as a monolayer. On the other hand, photocatalytic degradation process exhibited better results in terms of speed of removal and used quantity of photocatalyst, where 20 mg of SnO2/MgO composite can be used to remove > 99% of SSY dye within 30 min. Mechanism of SSY adsorption and photocatalytic degradation was discussed. In addition, elution experiments demonstrated that the SnO2/MgO composite as an SSY adsorbent could be reused for nine cycles without considerable reduction in the SSY adsorption efficiency. Therefore, this work exhibited that the mesoporous SnO2/MgO composite can be considered an effective adsorbent/photocatalyst to remove SSY dye from real industrial effluent water at neutral pH conditions.

Synergistic effect of gold nanoparticles anchored on conductive carbon black as an efficient electrochemical sensor for sensitive detection of anti-COVID-19 drug Favipiravir in absence and presence of co-administered drug Paracetamol.

Favipiravir (FVP) is introduced as a promising newly developed antiviral drug against the coronavirus disease 2019 (COVID-19). Therefore, the accurate determination of FVP is of great significance for quality assessment and clinical diagnosis. Herein, a novel electrochemical sensing platform for FVP based on gold nanoparticles anchored conductive carbon black (Au@CCB) modified graphite nanopowder flakes paste electrode (GNFPE) was constructed. Morphological and nanostructure properties of Au@CCB have been investigated by TEM, HRTEM, and EDX methods. The morphology and electrochemical properties of Au@CCB/GNFPE were characterized by SEM, cyclic voltammetry (CV), and EIS. The Au@CCB nanostructured modified GNFPE exhibited strong electro-catalytic ability towards the oxidation of FVP. The performance of the fabricated Au@CCB/GNFPE was examined by monitoring FVP concentrations in the absence and presence of co-administered drug paracetamol (PCT) by AdS-SWV. It was demonstrated that the proposed sensor exhibited superior sensitivity, stability, and anti-interference capability for the detection of FVP. The simultaneous determination of a binary mixture containing FVP and the co-administered drug PCT using Au@CCB/GNFPE sensor is reported for the first time. Under optimized conditions, the developed sensor exhibited sensitive voltammetric responses to FVP and PCT with low detection limits of 7.5 nM and 4.3 nM, respectively. The sensing electrode was successfully used to determine FVP and PCT simultaneously in spiked human plasma and pharmaceutical preparations, and the findings were satisfactory. Finally, the fabricated sensor exhibited high sensitivity for simultaneous detection of FVP and PCT in the presence of ascorbic acid in a real sample.

Light trapping by porous TiO2 hollow hemispheres for high efficiency photoelectrochemical water splitting.

Photocatalytic water splitting has recently received increasing attention as a green fuel source. The controlled nano-geometry of the photocatalytic material can improve light harvesting. In this study, as a proof of concept, hollow hemisphere (HHS)-based films of TiO2 material were created by a conventional electrospray method and subsequently applied for photoelectrochemical (PEC) water splitting. To preserve the morphology of the HHS structure, a hydrolysis precipitation phase separation method (HPPS) was developed. As a result, the TiO2 HHS-based thin films presented a maximum PEC water splitting efficiency of ca. 0.31%, almost two times that of the photoanode formed by TiO2 nanoparticle-based films (P25). The unique morphology and porous structure of the TiO2 HHSs with reduced charge recombination and improved light absorption are responsible for the enhanced PEC performance. Light scattering by the HHS was demonstrated with total reflection internal fluorescence microscopy (TRIFM), revealing the unique light trapping phenomenon within the HHS cavity. This work paves the way for the rational design of nanostructures for photocatalysis in fields including energy, environment, and organosynthesis.

Controllable Fabrication of Zn2+ Self-Doped TiO2 Tubular Nanocomposite for Highly Efficient Water Treatment.

Tailoring high-efficiency photocatalytic composites for various implementations is a major research topic. 1D TNTs-based nanomaterials show promise as a photocatalyst for the remediation of organic pigments in an aqueous solution. Despite this, TiO2 (TNTs) is only photoactive in the UV range due to its inherent restriction on absorption of light in the UV range. Herein, we provide a facile recipe to tailor the optical characteristics and photocatalytic activity of TNTs by incorporating Zn (II) ionic species via an ion-exchange approach in an aqueous solution. The inclusion of Zn (II) ions into the TNTs framework expands its absorption of light toward the visible light range, therefore TiO2 nanotubes shows the visible-light photo-performance. Activity performance on photocatalytic decontamination of RhB at ambient temperature demonstrates that Zn-TNTs offer considerable boosted catalytic performance compared with untreated tubular TiO2 during the illumination of visible light. RhB (10 mg L-1) degradation of around 95% was achieved at 120 min. Radical scavenger experiment demonstrated that when electron (e-) or holes (h+) scavengers are introduced to the photodegradation process, the assessment of decontamination efficacy decreased by 45% and 76%, respectively. This demonstrates a more efficient engagement of the photoexcited electrons over photogenerated holes in the photodegradation mechanism. Furthermore, there seems to be no significant decrease in the activity of the Zn-TNTs after five consecutive runs. As a result, the fabricated Zn-TNTs composite has a high economic potential in the energy and environmental domains.

Bifunctional ratiometric sensor based on highly fluorescent nitrogen and sulfur biomass-derived carbon nanodots fabricated from manufactured dairy product as a precursor.

Novel biomass-derived carbon dots co-doped with nitrogen and sulfur were fabricated through facile and simple synthetic method from manufactured milk powder and methionine as precursors. The as-fabricated platform was used for ratiometric fluorescence sensing of Cu (II) and bisphosphonate drug risedronate sodium. The sensing platform is based on oxidation of o-phenylenediamine by Cu (II) to form 2, 3-diaminophenazine (oxidized product) with an emission peak at 557 nm. The resultant product quenched the fluorescence emission of as-fabricated carbon dots at 470 nm through Förster resonance energy transfer (FRET) and inner-filter effect (IFE). Upon addition of risedronate sodium, the formation of 2, 3-diaminophenazine was decreased as a result of Cu (II) chelation with risedronate sodium, recovering the fluorescence emission of carbon dots. The ratio of fluorescence at 470 nm and 557 nm was measured as a function of Cu (II) and risedronate sodium concentrations. The proposed sensing platform sensitively detected Cu (II) and risedronate sodium in the range of 0.01-55 µM and 5.02-883 µM with LODs (S/N = 3) of 0.003 µM and 1.48 µM, respectively. The sensing platform exhibited a good selectivity towards Cu (II) and risedronate sodium. The sensing system was used to determine Cu (II) and risedronate sodium in different sample matrices with recoveries % in the range of 99-103 % and 97.4-103.8 %, and RSDs % in the range of 1.5-3.0 % and 1.8-3.6 %, respectively.

Hydrothermal Conversion of Food Waste to Carbonaceous Solid Fuel-A Review of Recent Developments.

This review critically discussed recent developments in hydrothermal carbonization (HTC) of food waste and its valorization to solid fuel. Food waste properties and fundamentals of the HTC reactor were also covered. The review further discussed the effect of temperature, contact time, pressure, water-biomass ratio, and heating rate on the HTC of food waste on the physiochemical properties of hydrochar. Literature review of the properties of the hydrochar produced from food waste in different studies shows that it possesses elemental, proximate, and energy properties that are comparable to sub-bituminous coal and may be used directly as fuel or co-combusted with coal. This work conclusively identified the existing research gaps and provided recommendation for future investigations.

Selective Spectrofluorimetric Approach for the Assessment of Two Antipsychotic Drugs through Derivatization with O-Phthalaldehyde.

A facile and sensible spectrofluorimetric approach for the measurement of two antipsychotic medications, aripiperazole (ARP) and clozapine (CLZ), was devised and validated. The approach involves reacting the examined medicines with o-phthalaldehyde in the presence of ß-mercaptoethanol in a borate buffer of pH 9.0 and pH 10 for ARP and CLZ, respectively, to produce a robustly fluorescent compound that is detected at 450 nm following excitation at 340 nm. The experimental variables influencing the performance and product stability were thoroughly investigated and optimized. Under optimal conditions, the intensity of the fluorescence was linear during a concentration range of 0.1-0.5 µg/mL, with a limit of detection (0.0391 and 0.0400 µg/mL) and limit of quantitation (0.1035 and 0.1332 µg/mL), respectively, for ARP and CLZ. The suggested approach was successful in analyzing commercialized tablets. A statistical investigation of the results produced by the suggested and standard methods showed no remarkable variation in the precision and accuracy of the two approaches. A chemical mechanism using o-phthalaldehyde was proposed.

Comparative Investigation of the Physicochemical Properties of Chars Produced by Hydrothermal Carbonization, Pyrolysis, and Microwave-Induced Pyrolysis of Food Waste.

This work presents a comparative study of the physicochemical properties of chars derived by three thermochemical pathways, namely: hydrothermal carbonization, HTC (at 180, 200 and 220 °C), pyrolysis, PY, (at 500, 600 and 700 °C) and microwave assisted pyrolysis, MW (at 300, 450 and 600 W). The mass yield of HTC samples showed a decrease (78.7 to 26.7%) as the HTC temperature increased from 180 to 220 °C. A similar decreasing trend in the mass yield was also observed after PY (28.45 to 26.67%) and MW (56.45 to 22.44%) of the food waste mixture from 500 to 700 °C and 300 to 600 W, respectively. The calorific value analysis shows that the best among the chars prepared by three different heating methods may be ranked according to the decreasing value of the heating value as: PY500, MW300, and HTC180. Similarly, a decreasing trend in H/C values was observed as: PY500 (0.887), MW300 (0.306), and HTC180 (0.013). The scanning electron microscope (SEM) analyses revealed that the structure of the three chars was distinct due to the different temperature gradients provided by the thermochemical processes. The results clearly show that the suitable temperature for the HTC and PY of food waste was 180 °C and 500 °C, respectively, while the suitable power for the MW of food waste was 300 W.

Biogenic-Mediated Synthesis of the Cs2O-MgO/MPC Nanocomposite for Biodiesel Production from Olive Oil.

In this work, a biogenic-mediated approach is successfully used to synthesize a novel heterogeneous Cs2O-MgO/MPC basic nanocomposite. For the first time, the established technicality employs pomegranate seed extract that gives a green capping fuel and reducing mediators during an aqueous solution combustion process of metal ion precursors. The synthesized nanocomposites were identified by X-ray diffraction, Fourier transform infrared, N2 isotherms, field emission scanning electron microscopy, and CO2-TPD analyses. The transesterification process of olive oil was used to evaluate the catalytic performance. The nanocomposite displayed outstanding catalytic efficiency stemming from the boosting of the reactant and product diffusion. The transesterification activity and the optimization design were assessed by applying the response surface methodology. Based on the experimental tests, the finest experimental conditions with a biodiesel yield of 96.1% are 4 h, 4% catalyst amount, an oil/methanol ratio of 1:15, and a temperature of 65 °C. The predicted optimal conditions based on the statistical model are 6 h contact time, 5.2 % catalyst dose, 65 °C reaction temperature, and 1:15 oil/methanol molar ratio, attaining a biodiesel yield of 95.18%. The catalyst reusability has been performed almost continuously up to four cycles, with no loss of the active constituents. The obtained biodiesel demonstrated characteristics close to those of international standards of biodiesel. Besides, the process employed in this study demonstrated significant potential for further development and commercialization and is cheaper than the refined vegetable oil used in traditional approaches of biodiesel manufacturing.

Assessment of Trace Elements in Urban Road Dust of a City in a Border Province Concerning Their Levels, Sources, and Related Health Risks.

Most research studies regarding the contamination of urban road dust (RD) focused on mega cities, but little consideration is given for small cities in border areas. The present work investigated the trace elements content in 16 RD samples of particle size < 63 µm at six areas with different anthropogenic activities in Sakaka city, KSA. The trace elements were analyzed using XRF and ICP-MS. Significantly high trace elements concentrations were recorded at small-scale industrial area. Concentrations of trace elements are ranked as Fe > Mn > Pb > Zn > Cr > Cu > Co > As > Se. The contamination evaluation through enrichment factor calculation refers to the existence of an anthropogenic source for certain trace elements, such as Fe, Zn, Mn, Cu, and Pb. The values of contamination factor indicate the contamination of RD samples collected from small-scale industrial area with these trace elements. The highest pollution load index value recorded at this industrial area suggests that it is a highly polluted area. This was confirmed by applying the one-way ANOVA test for the difference analysis between the investigated areas. The correlation between most of the detected trace elements at the small scale-industrial area was lost due to the variation in their industrial sources. The health risk of some detected trace elements was estimated for two groups of populations, namely workers at the small scale-industrial area and residents (adults and children) at residential areas at this city under study. Workers and resident children were more likely affected by arsenic through the ingestion pathway to cancer because of its higher cancer risk values that were more than the acceptable value 1 × 10-6. Workers and residents (adults and children) are susceptible to noncarcinogenic risks through the ingestion pathway of Fe because of its higher hazard quotient values that are more than one.