Ultra-long-distance distribution of low-phase-noise reference lightwave for optical communications.

The remote delivery of optical reference with highly stable oscillation frequency and carrier phase can eliminate the need of digital signal processing for the estimation of these parameters in optical communication. The distribution distance of the optical reference has been limited, however. In this paper, an optical reference distribution over 12,600 km is achieved while maintaining low-noise characteristics, using an ultra-narrow-linewidth laser as a reference source and a fiber Bragg grating filter for noise removal. The distributed optical reference enables 10 GBaud, 5 wavelength-division-multiplexed dual-polarization 64QAM data transmission without using carrier phase estimation, which significantly reduces off-line signal processing time. In the future, this method can enable all coherent optical signals in the network to be synchronized to a common reference ideally, thereby improving overall energy efficiency and cost.

Real-time transmission of geometrically-shaped signals using a software-defined GPU-based optical receiver.

A software-defined optical receiver is implemented on an off-the-shelf commercial graphics processing unit (GPU). The receiver provides real-time signal processing functionality to process 1 GBaud minimum phase (MP) 4-, 8-, 16-, 32-, 64-, 128-ary quadrature amplitude modulation (QAM) as well as geometrically shaped (GS) 8- and 128-QAM signals using Kramers-Kronig (KK) coherent detection. Experimental validation of this receiver over a 91 km field-deployed optical fiber link between two Tokyo locations is shown with detailed optical signal-to-noise ratio (OSNR) investigations. A net data rate of 5 Gbps using 64-QAM is demonstrated.

Demonstration of a 90 Tb/s, 234.8 km, C+L band unrepeatered SSMF link with bidirectional Raman amplification.

This work demonstrates the use of bidirectional Raman amplification to achieve an unrepeatered 234 km link using standard single mode fibers and with a capacity×distance product of 21.132 Pb/s·km. A throughput above 90 Tb/s is achieved with an 87 nm wavelength-division multiplexed signal carrying 424 PDM-64QAM signals at 24.5 GBaud across C and L bands. Transmission is supported using up to 12 Raman pumps per propagation direction, covering a wavelength range between 1410.8 nm and 1502.7 nm and with total power under 2.6 W.

S-, C- and L-band transmission over a 157†nm bandwidth using doped fiber and distributed Raman amplification.

We investigate optical transmission of an ultra-wideband signal in a standard single mode fiber. Using a near continuous optical bandwidth exceeding 157 nm across the S-, C- and L-bands, we combine doped-fiber amplifiers covering S, C and L-bands with distributed Raman amplification to enable high-quality transmission of polarization division multiplexed (PDM)-256-quadrature-amplitude modulation (QAM) signals over a 54 km standard single-mode fiber. We receive 793 × 24.5 GBd signals from 1466.34 nm to 1623.57 nm and measure a data rate estimated from the generalized mutual information (GMI) of 256.4 Tb/s and an LDPC decoded throughput of 244.3 Tb/s. The measured data rates exceed the highest previously measured in a single mode fiber, showing the potential for S-band transmission to enhance achievable data rates in optical fibers.

Peta-bit-per-second optical communications system using a standard cladding diameter 15-mode fiber.

Data rates in optical fiber networks have increased exponentially over the past decades and core-networks are expected to operate in the peta-bit-per-second regime by 2030. As current single-mode fiber-based transmission systems are reaching their capacity limits, space-division multiplexing has been investigated as a means to increase the per-fiber capacity. Of all space-division multiplexing fibers proposed to date, multi-mode fibers have the highest spatial channel density, as signals traveling in orthogonal fiber modes share the same fiber-core. By combining a high mode-count multi-mode fiber with wideband wavelength-division multiplexing, we report a peta-bit-per-second class transmission demonstration in multi-mode fibers. This was enabled by combining three key technologies: a wideband optical comb-based transmitter to generate highly spectral efficient 64-quadrature-amplitude modulated signals between 1528 nm and 1610 nm wavelength, a broadband mode-multiplexer, based on multi-plane light conversion, and a 15-mode multi-mode fiber with optimized transmission characteristics for wideband operation.

Experimental evaluation of the impact of the light source on the measurement of short-term average crosstalk in homogeneous single-mode multi-core fibers.

This work compares the random time-varying crosstalk in homogeneous multi-core fibers measured using different types of light sources with linewidths ranging from 100 Hz to 2.5 MHz. We show that the frequency stability of the light source plays a significant role on the quality of short-term average crosstalk measurements with no observable impact from laser linewidth. We also compare the use of filtered amplified spontaneous emission noise and coherent light sources for crosstalk measurements. The former are shown to enable average crosstalk measurements in short time periods. In contrast, measurements using coherent light sources require long measurement periods to reach similar results.

Space-division multiplexed transmission in the S-band over 55 km few-mode fibers.

Transmission of highly spectral efficient 24.5 GBaud quadrature phase shift keying and 16- and 64-quadrature amplitude modulated signals in the S-band between 1492 nm and 1518 nm wavelength is demonstrated over 55 km few-mode fibers. The carrier lines for S-band transmission were generated by a single wideband optical comb source with more than 120 nm optical bandwidth. While the three-mode fiber was originally optimized for C- and L-band transmission, we show that differential mode delay and mode-dependent loss show only a minor wavelength dependence within the measured S-band channels. However, the transceiver sub-system, including S-band optical amplifiers as well as a reduced optical signal-to-noise ratio of the comb source, leads to a significant Q-factor penalty for channels towards the edges of the S-band optical amplifiers below 1495 nm and above 1515 nm wavelength.

Master-slave carrier recovery for M-QAM multicore fiber transmission.

Master-slave carrier recovery is a digital signal processing technique that uses correlated phase noise in multi-channel receivers to eliminate redundant carrier recovery blocks. In this paper we experimentally investigate the performance of master-slave carrier recovery for multicore fiber transmission in the presence of inter-channel nonlinear interference. Using a triple parallel loop setup we jointly receive three spatial channels in a 7-core fiber for transmission distances of up to 1600 km. We find that an increased launch power causes a moderate penalty on the slave channels. Furthermore, we study the penalty from a non-zero inter-core skew.

Long distance crosstalk-supported transmission using homogeneous multicore fibers and SDM-MIMO demultiplexing.

We propose and evaluate the use of spatial-division multiplexing (SDM) multiple input multiple output (MIMO) systems to support long distance transmission using single-mode homogeneous multicore fibers. We show that on a uniform link with per-span inter-core skew compensation, the required SDM-MIMO memory length corresponds to the largest inter-core skew per span on the link. Furthermore, we show that with inter-core skew compensation, the required memory length of the SDM-MIMO is nearly constant with the transmission distance for accumulated crosstalk below -11 dB. We experimentally demonstrate the use of SDM-MIMO with a memory length of 20 ns on a long distance transmission link using 20 GBaud PDM-QPSK signals. We achieve a reach of 9780 km, which corresponds to a 9% improvement over the case without SDM-MIMO. We also show that the use of SDM-MIMO is applicable to the transmission of signals with higher modulation order, achieving transmission reach improvements of 14% for 20 GBaud PDM-16QAM and PDM-64QAM signals.

Few-mode fiber, splice and SDM component characterization by spatially-diverse optical vector network analysis.

This paper discusses spatially diverse optical vector network analysis for space division multiplexing (SDM) component and system characterization, which is becoming essential as SDM is widely considered to increase the capacity of optical communication systems. Characterization of a 108-channel photonic lantern spatial multiplexer, coupled to a 36-core 3-mode fiber, is experimentally demonstrated, extracting the full impulse response and complex transfer function matrices as well as insertion loss (IL) and mode-dependent loss (MDL) data. Moreover, the mode-mixing behavior of fiber splices in the few-mode multi-core fiber and their impact on system IL and MDL are analyzed, finding splices to cause significant mode-mixing and to be non-negligible in system capacity analysis.

Crosstalk dynamics in multi-core fibers.

Inter-core crosstalk is a potential limitation on the achievable data-rates in optical fiber transmission systems using multi-core fibers. Crosstalk arises from unwanted coupling between cores of a homogenous multi-core fiber and it's average power has been observed to vary over time by 10s of decibels, potentially requiring an additional performance margin to achieve acceptable outage probability. Most investigations of crosstalk have so far only considered continuous wave laser light or amplified spontaneous emission as sources of crosstalk. In this paper, we theoretically and experimentally investigate the time-dependence of inter-core crosstalk in a homogeneous multi-core fiber when considering signals with various modulation formats and symbol rates. We find that crosstalk power fluctuations depend on the symbol rate, modulation and skew between cores. For carrier-free signals, such as quadrature amplitude modulation, the crosstalk power is nearly constant for expected conditions of multi-core transmission systems. However, carrier-supported signals, such as OOK, always induce time-varying crosstalk powers.

Performance of adaptive DD-OFDM multicore fiber links and its relation with intercore crosstalk.

Adaptive direct-detection (DD) orthogonal frequency-division multiplexing (OFDM) is proposed to guarantee signal quality over time in weakly-coupled homogenous multicore fiber (MCFs) links impaired by stochastic intercore crosstalk (ICXT). For the first time, the received electrical power of the ICXT and the performance of the adaptive DD-OFDM MCF link are experimentally monitored quasi-simultaneously over a 210 hour period. Experimental results show that the time evolution of the error vector magnitude due to the ICXT can be suitably estimated from the normalized power of the detected crosstalk. The detected crosstalk results from the beating between the carrier in the test core and ICXT originating from the carrier and modulated signal from interfering core. The results show that the operation of DD-OFDM systems employing fixed modulation can be severely impaired by the presence of ICXT that may unpredictable vary in both power and frequency. The system may suffer from deleterious impact of moderate ICXT levels over a time duration of several hours or from peak ICXT levels occurring over a number of minutes. Such power fluctuations can lead to large variations in bit error ratio (BER) for static modulation schemes. Here, we show that BER fluctuations may be minimized by the use of adaptive modulation techniques and that in particular, the adaptive OFDM is a viable solution to guarantee link quality in MCF-based systems. An experimental model of an adaptive DD-OFDM MCF link shows an average throughput of 12 Gb/s that represents a reduction of only 9% compared to the maximum throughput measured without ICXT and an improvement of 23% relative to throughput obtained with static modulation.

Single parity check-coded 16QAM over spatial superchannels in multicore fiber transmission.

We experimentally investigate single-parity check (SPC) coded spatial superchannels based on polarization-multiplexed 16-ary quadrature amplitude modulation (PM-16QAM) for multicore fiber transmission systems, using a 7-core fiber. We investigate SPC over 1, 2, 4, 5 or 7 cores in a back-to-back configuration and compare the sensitivity to uncoded PM-16QAM, showing that at symbol rates of 20 Gbaud and at a bit-error-rate (BER) of 10-3, the SPC superchannels exhibit sensitivity improvements of 2.7 dB, 2.0 dB, 1.7 dB, 1.3 dB, and 1.1 dB, respectively. We perform both single channel and wavelength division multiplexed (WDM) transmission experiments with 22 GHz channel spacing and 20 Gbaud channel symbol rate for SPC over 1, 3 and 7 cores and compare the results to PM-16QAM with the same spacing and symbol rate. We show that in WDM signals, SPC over hl1 core can achieve more than double the transmission distance compared to PM-16QAM at the cost of 0.91 bit/s/Hz/core in spectral efficiency (SE). When sharing the parity-bit over 7 cores, the loss in SE becomes only 0.13 bit/s/Hz/core while the increase in transmission reach over PM-16QAM is 44 %.

High-capacity self-homodyne PDM-WDM-SDM transmission in a 19-core fiber.

We investigate a high-capacity, space-division-multiplexed (SDM) transmission system using self-homodyne detection (SHD) in multi-core fiber (MCF). We first investigate SHD phase noise cancellation with both kHz and MHz range linewidths for both quadrature-phase shift-keyed (QPSK) and 16 quadrature-amplitude modulation (16QAM) signals, finding that phase noise cancellation in SHD enabled transmission with MHz linewidth lasers that resulted in error floors when using intradyne detection. We then demonstrate a high throughput SHD transmission system using low-cost, MHz linewidth distributed feedback lasers. We transmit a CW pilot-tone on a single core of a 10.1 km MCF span with the remaining 18 cores used to transmit 125 wavelength-division multiplexed (WDM) QPSK and polarization-division-multiplexed (PDM)-QPSK signals with 50 GHz channel spacing at 25 GBd. For PDM transmission and assuming a 7% forward-error correction overhead this is equivalent 210 Tb/s transmission with a SE of 33.4 b/s/Hz. High-capacity transmission is achieved despite high inter-core crosstalk, broad transmitter linewidth and narrow channel spacing, showing that combining SHD with MCF enables high throughput, low-cost transmission in next-generation optical networks.

19-core MCF transmission system using EDFA with shared core pumping coupled via free-space optics.

We report the development of a space division multiplexed (SDM) transmission system consisting of a 19-core fiber and 19-core Erbium-doped fiber amplifier (EDFA). A new 19-core fiber with an improved core arrangement was employed to achieve a low aggregated inter-core crosstalk of -42 dB at 1550 nm over 30 km. The EDFA uses shared free-space optics for pump beam combining and isolation, thus is SDM transparent and has some potential for cost reduction. 19.6 dB to 23.3 dB gain and 6.0 dB to 7.0 dB noise figure were obtained for each SDM channel at 1550 nm. System feasibility for SDM transmission over 1200 km was demonstrated with 100 Gb/s PDM-QPSK signals.

Investigating self-homodyne coherent detection in a 19 channel space-division-multiplexed transmission link.

We investigate the performance of a self-homodyne coherent detection (SHCD) system using a 19 core multi-core fiber (MCF) and 16 wavelength-division-multiplexed channels. We show that SHCD, with the pilot-tone transmitted on a single MCF core and information carrying signals on the remaining cores, is compatible with space-division-multiplexed transmission, potentially relaxing laser linewidth and digital signal processing requirements due to phase noise cancellation. However, inter-core crosstalk can have an impact on performance and core selection.

Performance evaluation of a burst-mode EDFA in an optical packet and circuit integrated network.

We experimentally investigate the performance of burst-mode EDFA in an optical packet and circuit integrated system. In such networks, packets and light paths can be dynamically assigned to the same fibers, resulting in gain transients in EDFAs throughout the network that can limit network performance. Here, we compare the performance of a 'burst-mode' EDFA (BM-EDFA), employing transient suppression techniques and optical feedback, with conventional EDFAs, and those using automatic gain control and previous BM-EDFA implementations. We first measure gain transients and other impairments in a simplified set-up before making frame error-rate measurements in a network demonstration.

Field trial of 160 Gbit/s DWDM-based optical packet switching and transmission.

We demonstrated, for the first time, a field trial of 160 (16 lambda x 10) Gbit/s, fine granularity, DWDM-based optical packet switching and transmission by newly-developed burst-mode EDFAs and an optical packet switch prototype with multiple all-optical label processors. We achieved 64 km field transmission and switching of 160 (16 lambda x 10) Gbit/s DWDM-based optical packets encapsulating almost 10 Gbit/s IP packets with error-free operation (IP-packet-loss-rate <10(-6) and bit-error-rate <10(-9)).