RESUMEN
Natural plant based fibres are being increasingly used in sustainable fibre reinforced composite applications in order to meet the demand of using environmentally friendly materials for composites. Fibre metal laminates (FMLs) are used in aerospace, automobile, marine and civil engineering applications, due to their excellent mechanical behaviors compared to traditional metals and their alloys. This study describes a novel fabrication of jute fibre reinforced aluminum metal laminates, using different jute fibre architectures (plain and twill fabric structures), wherein jute fibres were used in the skins and aluminum in the core layers. Jute fibres and aluminum sheets were chemically treated to enhance the compatibility and interfacial bonding at fibre-metals-matrix interfaces. FMLs were manufactured by hot pressing technique, after the application of wet lay-up process for the resin impregnation and they were further tested under tensile, flexural and impact loading conditions. While comparing results, the twill architecture showed improved tensile and flexural properties compared to plain fabric based FMLs. Chemical treatments on twill jute fibres and metal sheets further exceptionally enhanced the flexural properties (151 MPa flexural strength and 21.3 GPa modulus and they were increased by 186.5 % and 722.7 % respectively compared to the untreated jute fibre counterparts) of the laminates due to a significant improvement in the adhesion between the jute fibre and aluminum sheet after alkali treatment applied. Therefore, with these enhanced properties, jute based FML laminates can be used as sustainable composite materials in many structural applications.
RESUMEN
Natural-based lignocellulose fibrous materials can be used as a sustainable alternative to conventional fossil-based fibers such as glass fibers, in lightweight fiber-reinforced thermoplastic composites for marine, automotive, aerospace, or other advanced applications. However, one of the main challenges in using natural fiber-based thermoplastic composites is the low mechanical performance of composite structures. This can be improved significantly through the development of an optimized novel fiber architecture with enhanced fiber packing properties, following a low-cost production process. In this context, this study demonstrates a less energy-consuming and cheaper manufacturing process, for developing highly individualized short jute fiber-based dry fiber preform architecture, with an improved fiber packing property. Short jute fibers were chemically treated with alkali and PVA sizing treatments in the processing of new fiber preform architectures, and they were used in manufacturing of ultimate short jute fiber/polypropylene (PP) thermoplastic composites. The newly developed short fiber thermoplastic composites showed a significant improvement in mechanical properties (tensile, flexural, and impact) compared to any other natural fiber architecture-based (woven, knitted, nonwoven, unidirectional, etc.) composites found in the literature. Due to the use of new fiber architecture, the developed composites' fiber content was observed to increase. In addition, the compatibility of jute fibers with the polypropylene matrix was strengthened with the application of chemical treatments on highly individualized jute fibers. These reasons were responsible for the enhancement of mechanical properties of developed composites. Micromechanics of the fibers in composites were evaluated using the modified rule of the mixture and Halpin-Tsai equations for stiffness prediction of the composites in order to develop a theoretical understanding of newly developed composites' mechanics. It is thought that the improved mechanical performance of short jute fiber/PP thermoplastic composites can extend the use of these composites in many load-demanding applications, wherein normally synthetic fiber composites are used.
RESUMEN
The fiber architecture can significantly influence the rate of impregnation of a resin in making composites and the load-bearing ability of individual fibers on testing of the loading directions. Moreover, achieving the maximum mechanical performance of a natural fiber composite selection of yarn liner density and optimization of fabric structure and further modification of the composites remains a great challenge for the composite research community. In this study, a number of jute-based woven derivatives (plain, 2/1 twill, 3/1 twill, zigzag based on a 2/2 twill, and diamond based on a 2/2 twill) have been constructed from similar linear densities of yarn. The effect of the fabric architecture and further modification of optimized composites by applying γ-radiation is also explained in this study. The experimental results show a 54% increase in tensile strength, a 75% increase in tensile modulus, a 69% increase in flexural strength, a 124% increase in flexural modulus, and 64% increase in impact strength of twill (3/1) structured jute fiber polyester composites in comparison to other plain and twill structured composites. A further mechanical improvement of around 20-30% is possible for the optimized twill structured composites by applying γ-radiation on the composites. An FTIR, TGA, and SEM study confirms the chemical, thermal, and fractographic changes after applying the modification of composites.
