Reconfigurable beam-steerable leaky-wave antenna loaded with metamaterial apertures using liquid crystal-based delay lines.

An original liquid crystal (LC)-based substrate integrated waveguide (SIW) leaky-wave antenna is proposed. Inside the SIW, there is an embedded stripline sandwiched between an LC pool and another dielectric slab. The antenna couples the guided quasi-TEM mode into free space through a periodic set of complementary electric inductive-capacitive (cELC) resonators. Simulation results show that the antenna performs fixed-frequency continuous beam steering of 52° from backward -28° to forward 24° at 25.85 GHz. This relatively wide beam scan angle is achieved by tuning the LC permittivity through an applied quasi-DC bias voltage to the stripline. Simulation results show that the antenna has high realized gain through the entire scanning range (less than 1 dB degradation), relatively wide bandwidth, and good tolerance to frequency drift and fabrication errors.

Fabrication and spectroscopic characterization of graphene transparent electrodes on flexible cyclo-olefin substrates for terahertz electro-optic applications.

We demonstrate graphene on flexible, low-loss, cyclo-olefin polymer films as transparent electrodes for terahertz electro-optic devices and applications. Graphene was grown by chemical vapor deposition and transferred to cyclo-olefin polymer substrates by the thermal release tape method as layers on an approximate area of 4 cm2. The structural and electromagnetic properties of the graphene samples as well as their spatial variation were systematically mapped by means of µRaman, terahertz time-domain and mid-infrared spectroscopy. Thanks to the small thickness and very low intrinsic absorption of the employed substrates, both high transmittance and conductivity were recorded, demonstrating the suitability of the technique for the fabrication of a new class of transparent and flexible electrodes working in the terahertz spectrum.

Toroidal metasurface resonances in microwave waveguides.

We theoretically investigate the possibility to load microwave waveguides with dielectric particle arrays that emulate the properties of infinite, two-dimensional, all-dielectric metasurfaces. First, we study the scattering properties and the electric and magnetic multipole modes of dielectric cuboids and identify the conditions for the excitation of the so-called anapole state. Based on the obtained results, we design metasurfaces composed of a square lattice of dielectric cuboids, which exhibit strong toroidal resonances. Then, three standard microwave waveguide types, namely parallel-plate waveguides, rectangular waveguides, and microstrip lines, loaded with dielectric cuboids are designed, in such a way that they exhibit the same resonant features as the equivalent dielectric metasurface. The analysis shows that parallel-plate and rectangular waveguides can almost perfectly reproduce the metasurface properties at the resonant frequency. The main attributes of such resonances are also observed in the case of a standard impedance-matched microstrip line, which is loaded with only a small number of dielectric particles. The results demonstrate the potential for a novel paradigm in the design of "metasurface-loaded" microwave waveguides, either as functional elements in microwave circuitry, or as a platform for the experimental study of the properties of dielectric metasurfaces.

Anapole Modes in Hollow Nanocuboid Dielectric Metasurfaces for Refractometric Sensing.

This work proposes the use of the refractive index sensitivity of non-radiating anapole modes of high-refractive-index nanoparticles arranged in planar metasurfaces as a novel sensing principle. The spectral position of anapole modes excited in hollow silicon nanocuboids is first investigated as a function of the nanocuboid geometry. Then, nanostructured metasurfaces of periodic arrays of nanocuboids on a glass substrate are designed. The metasurface parameters are properly selected such that a resonance with ultrahigh Q-factor, above one million, is excited at the target infrared wavelength of 1.55 µm. The anapole-induced resonant wavelength depends on the refractive index of the analyte superstratum, exhibiting a sensitivity of up to 180 nm/RIU. Such values, combined with the ultrahigh Q-factor, allow for refractometric sensing with very low detection limits in a broad range of refractive indices. Besides the sensing applications, the proposed device can also open new venues in other research fields, such as non-linear optics, optical switches, and optical communications.

Guided-mode resonant narrowband terahertz filtering by periodic metallic stripe and patch arrays on cyclo-olefin substrates.

We experimentally and theoretically demonstrate a class of narrowband transmissive filters in the terahertz spectrum. Their operation is based on the excitation of guided-mode resonances in thin films of the low-loss cyclo-olefin polymer Zeonor, upon which aluminum stripe and patch arrays are patterned via standard photolithography. The filters are engineered to operate in low atmospheric loss THz spectral windows, they exhibit very high transmittance and quality factors, compact thickness, and mechanical stability. The dependence of their filtering properties on the geometrical parameters, the substrate thickness and the angle of incidence is investigated, discussing the physical limitations in their performance. This class of filters provides a cost-effective solution for broadband source or channel filtering in view of emerging terahertz wireless communication systems.

Directional Emission of Fluorescent Dye-Doped Dielectric Nanogratings for Lighting Applications.

By structuring a luminescent dielectric interface as a relief diffraction grating with nanoscale features, it is possible to control the intensity and direction of the emitted light. The composite structure of the grating is based on a fluorescent dye (Lumogen F RED 305) dispersed in a polymeric matrix (poly(methyl methacrylate)). Measurements demonstrate a significant enhancement of the emitted light for specific directions and wavelengths when the grating interface is compared to nonstructured thin films made of the same material. In particular, the maximum enhancement of photoluminescence for a given pump wavelength is obtained at an angle of incidence that is close to the Rayleigh anomaly condition for the first-order diffracted waves. In this condition, the maximum extinction of incident light is observed. Upon excitation with coherent and monochromatic sources, photoluminescence plots show that the Rayleigh anomalies confine the angular interval of the emitted light. Being the anomalies  directly related to the pitch of the diffraction grating, the system can be thus implemented as an optical device whose directional emission can be designed for specific applications. The exploitation of nanoimprinting techniques for the fabrication of the luminescent grating enables production of the device on large areas, paving the way for low-cost lighting and solar applications.

Electrically tunable terahertz polarization converter based on overcoupled metal-isolator-metal metamaterials infiltrated with liquid crystals.

Large birefringence and its electrical modulation by means of Fréedericksz transition makes nematic liquid crystals (LCs) a promising platform for tunable terahertz (THz) devices. The thickness of standard LC cells is in the order of the wavelength, requiring high driving voltages and allowing only a very slow modulation at THz frequencies. Here, we first present the concept of overcoupled metal-isolator-metal (MIM) cavities that allow for achieving simultaneously both very high phase difference between orthogonal electric field components and large reflectance. We then apply this concept to LC-infiltrated MIM-based metamaterials aiming at the design of electrically tunable THz polarization converters. The optimal operation in the overcoupled regime is provided by properly selecting the thickness of the LC cell. Instead of the LC natural birefringence, the polarization-dependent functionality stems from the optical anisotropy of ultrathin and deeply subwavelength MIM structures. The dynamic electro-optic control of the LC refractive index enables the spectral shift of the resonant mode and, consequently, the tuning of the phase difference between the two orthogonal field components. This tunability is further enhanced by the large confinement of the resonant electromagnetic fields within the MIM cavity. We show that for an appropriately chosen linearly polarized incident field, the polarization state of the reflected field at the target operation frequency can be continuously swept between the north and south pole of the Poincaré sphere. Using a rigorous Q-tensor model to simulate the LC electro-optic switching, we demonstrate that the enhanced light-matter interaction in the MIM resonant cavity allows the polarization converter to operate at driving voltages below 10 Volt and with millisecond switching times.

Tunable terahertz fishnet metamaterials based on thin nematic liquid crystal layers for fast switching.

The electrically tunable properties of liquid-crystal fishnet metamaterials are theoretically investigated in the terahertz spectrum. A nematic liquid crystal layer is introduced between two fishnet metallic structures, forming a voltage-controlled metamaterial cavity. Tuning of the nematic molecular orientation is shown to shift the magnetic resonance frequency of the metamaterial and its overall electromagnetic response. A shift higher than 150 GHz is predicted for common dielectric and liquid crystalline materials used in terahertz technology and for low applied voltage values. Owing to the few micron-thick liquid crystal cell, the response speed of the tunable metamaterial is calculated as orders of magnitude faster than in demonstrated liquid-crystal based non-resonant terahertz components. Such tunable metamaterial elements are proposed for the advanced control of electromagnetic wave propagation in terahertz applications.

Beam-splitter switches based on zenithal bistable liquid-crystal gratings.

The tunable optical diffractive properties of zenithal bistable nematic liquid-crystal gratings are theoretically investigated. The liquid-crystal orientation is rigorously solved via a tensorial formulation of the Landau-de Gennes theory and the optical transmission properties of the gratings are investigated via full-wave finite-element frequency-domain simulations. It is demonstrated that by proper design the two stable states of the grating can provide nondiffracting and diffracting operation, the latter with equal power splitting among different diffraction orders. An electro-optic switching mechanism, based on dual-frequency nematic materials, and its temporal dynamics are further discussed. Such gratings provide a solution towards tunable beam-steering and beam-splitting components with extremely low power consumption.

Observation of tunable optical filtering in photosensitive composite structures containing liquid crystals.

We report on the investigation and characterization of an optically tunable filtering effect, observed in a waveguide grating made of alternated strips of photocurable polymer and a mixture of azo-dye-doped liquid crystal. The grating is sandwiched between two borosilicate glasses, one of which includes an ion-exchanged channel waveguide, which confines the optical signal to be filtered. Exposure to a low power visible light beam modifies the azo-dye molecular configuration, thus allowing the filtered wavelength to be tuned over a 6.6 nm range. Simulations of the filtering response are well described with our experimental findings.

Guided lamb wave electroacoustic devices on micromachined AlN/Al plates.

An electroacoustic micro-device based on the propagation of guided acoustic Lamb waves in AlN/Al plate is described. The AlN thin film is deposited by sputtering technique, optimized to achieve a high degree of orientation (rocking curve full-width at half-maximum /sp lap/ 3.5 degrees ) of the c-axis perpendicular to the plate surface. The AlN plate is micromachined using anisotropic reactive ion etching (RIE), followed by isotropic RIE to remove the silicon underlayer. Simulation results for the dispersion phase velocity curves and the electromechanical coupling coefficient (K(2)) are obtained by the matrix method and by the finite element method and compared with experimental data. A delay line is implemented on the structure and tested for the propagation of the first symmetrical Lamb mode (s(0)) at the frequency of 1.22 GHz. Measurements have shown that the structure is suitable for implementation of arrays of electroacoustic devices on a single chip for application to both sensing devices and signal processing systems.

Liquid-crystal tunable filter based on sapphire microspheres.

We design an integrated optoelectronic device based on the whispering-gallery modes of a sapphire microsphere integrated with a liquid-crystal tuning medium to produce a narrowband, electrically tunable, channel-dropping filter. The sapphire microsphere is glued over a diffused waveguide in a glass substrate. At the base of the microsphere, a small volume of liquid crystal is infiltrated. We numerically evaluate the performance of the device and demonstrate a voltage tuning of the narrowband resonances.

Tunable integrated optical filter made of a glass ion-exchanged waveguide and an electro-optic composite holographic grating.

We report the fabrication and the optical characterization of a hybrid tunable integrated optical filter. It consists of a diffused ion-exchanged channel waveguide on a borosilicate glass substrate with a cover of the same glass to form a gap filled with a holographic grating. The grating morphology, called POLICRYPS (POlymer LIquid CRYstal Polymer Slices), is made of alternating stripes of polymer and liquid crystal acting as overlayer for the underneath waveguide. The filter structure includes aluminum coplanar electrodes to electrically control the grating properties, allowing the tunability of the filter. The electric driving power required to tune the filter obtained was in the range of submilliwatts due to the efficient liquid crystal electro-optic effect.

Photonic devices based on preferential etching.

We introduce a design concept of optical waveguides characterized by a practical and reproducible process based on preferential etching of crystalline silicon substrates. Low-loss waveguides, spot-size converters, and power dividers have been obtained with polymers. We have also aligned liquid crystals in the waveguides and demonstrated guided propagation. Therefore this technology is a suitable platform for soft-matter photonics and heterogeneous integration.