Comparison of the Antibacterial Activity of Selected Deep Eutectic Solvents (DESs) and Deep Eutectic Solvents Comprising Organic Acids (OA-DESs) Toward Gram-Positive and Gram-Negative Species.

Deep eutectic solvents (DESs) have been intensively investigated in recent years for their antibacterial properties, with DESs that comprise organic acids (OA-DESs) showing promising antibacterial action. However a majority of the reports focused only on a limited number strains and techniques, which is not enough to determine the antibacterial potential of a substance. To bridge this gap, the antibacterial activity of classical DESs and OA-DESs is assessed on twelve Gram-negative and Gram-positive bacteria strains, with some of them exhibiting specific resistance toward antibiotics. The investigated formulations of OA-DESs comprise glycolic, malic, malonic, and oxalic acids as representatives of this group. Using a range of microbiological assays as well as physicochemical characterization methods, a major difference of the effectiveness between the two groups is demonstrated, with OA-DESs exhibiting, as expected, greater antibacterial effectiveness than classical DESs. Most interestingly, slight differences in the minimum inhibitory and bactericidal concentration values as well as time-kill kinetics profiles are observed between Gram-positive and Gram-negative strains. Transmission electron microscopy analysis reveals the effect of the treatment of the bacteria with the representatives of both groups of DESs, which allows us to better understand the possible mechanism-of-action of these novel materials.

Integrating Benzoxazine-PDMS 3D Networks with Carbon Nanotubes for flexible Pressure Sensors.

Shapeable and flexible pressure sensors with superior mechanical and electrical properties are of major interest as they can be employed in a wide range of applications. In this regard, elastomer-based composites incorporating carbon nanomaterials in the insulating matrix embody an appealing solution for designing flexible pressure sensors with specific properties. In this study, PDMS chains of different molecular weight were successfully functionalized with benzoxazine moieties in order to thermally cure them without adding a second component, nor a catalyst or an initiator. These precursors were then blended with 1 weight percent of multi-walled carbon nanotubes (CNTs) using an ultrasound probe, which induced a transition from a liquid-like to a gel-like behavior as CNTs generate an interconnected network within the matrix. After curing, the resulting nanocomposites exhibit mechanical and electrical properties making them highly promising materials for pressure-sensing applications.

Negative Capacitance in Nanocomposite Based on High-Density Polyethylene (HDPE) with Multiwalled Carbon Nanotubes (CNTs).

Negative capacitance (NC), already observed in conducting polymer-based nanocomposites, was recently reported and evidenced at low frequencies (<10 kHz) in non-conducting polymer-based nanocomposites containing conductive particles. In this contribution, we demonstrate that it is possible to produce economic high-density polyethylene (HDPE) nanocomposites exhibiting an NC effect at low frequencies via a convenient and environmentally friendly extrusion-like process by only adjusting the duration of melt-mixing. Nanocomposite materials are produced by confining a limited quantity, i.e., 4.6 wt.%, of multiwalled carbon nanotubes (CNTs) within semi-crystalline HDPE to reach the percolation threshold. With increasing melt processing time, crystallites of HDPE developing at the surface of CNTs become bigger and perturbate the connections between CNTs leading to a dramatic change in the electrical behavior of the systems. More specifically, the link between NC and current oscillations is stressed while the dependence of NC with the size of polymer crystallites is evidenced. NC tends to appear when space charge effects take place in HDPE/MWCNT interfaces, in structures with convenient crystallite sizes corresponding to 10 min of melt-mixing.

Easy, Flexible and Standardizable Anti-Nascent Biofilm Activity Assay to Assess Implant Materials.

Medical implants have improved the quality of life of many patients. However, surgical intervention may eventually lead to implant microbial contamination. The aims of this research were to develop an easy, robust, quantitative assay to assess surface antimicrobial activities, especially the anti-nascent biofilm activity, and to identify control surfaces, allowing for international comparisons. Using new antimicrobial assays to assess the inhibition of nascent biofilm during persistent contact or after transient contact with bacteria, we show that the 5 cent Euro coin or other metal-based antibacterial coins can be used as positive controls, as more than 4 log reduction on bacterial survival was observed when using either S. aureus or P. aeruginosa as targets. The methods and controls described here could be useful to develop an easy, flexible and standardizable assay to assess relevant antimicrobial activities of new implant materials developed by industries and academics.

Development of Low-Viscosity and High-Performance Biobased Monobenzoxazine from Tyrosol and Furfurylamine.

This work details the scalable and solventless synthesis of a potential fully biobased monobenzoxazine resin derived from tyrosol and furfurylamine. The structure of the monomer was studied by nuclear magnetic resonance (NMR) spectroscopy and Fourier transform infrared (FTIR). The curing of the precursors was characterized by differential scanning calorimetry (DSC), rheological measurements, and thermogravimetric analysis (TGA). The properties of the resulting biobased polybenzoxazine were then determined by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMA). A thermally stable resin was obtained with 5% and 10% weight-reduction-temperature (T d5 and T d10) values of 349 and 395 °C, respectively, and a char yield of 53%. Moreover, the low melting temperature, low viscosity, and excellent thermomechanical behavior make this fully biobased resin a promising candidate for coating applications.

Multifunctionality of structural nanohybrids: the crucial role of carbon nanotube covalent and non-covalent functionalization in enabling high thermal, mechanical and self-healing performance.

This study proposes new kinds of functionalization procedures able to preserve specific properties of carbon nanotubes (CNTs) and to improve compatibility with the epoxy matrix. Through a covalent approach, for the first time, CNTs are functionalized with the same hardener agent, 4,4'-diaminodiphenyl sulfone, employed to solidify the epoxy matrix and capable to fulfill mechanical requirements of industrial structural resins. The same CNTs are non-covalently modified through the polymer wrapping mechanism with benzoxazine (Bz) terminated polydimethylsiloxane (PDMS). The comparison between electrical and mechanical properties of the nanocomposites highlights the success of the non-covalent functionalization in determining an increase in the glass transition temperature (Tg) and in better preserving the unfunctionalized CNT electrical conductivity. Besides, tunneling atomic force microscopy (TUNA), powerful to catch ultra-low currents, has been used for revealing the morphology on nanoscale domains and detecting the conductivity on the same location of CNT/epoxy resins. No electrical contacts to the grounds have been used for the TUNA analysis; a procedure that does not alter the results on the interface domains which experience contact areas with strong differences in their properties. The effectiveness of performed CNT functionalizations as a route to impart self-healing efficiency to the resin formulations has also been proved.

Cerium Salts: An Efficient Curing Catalyst for Benzoxazine Based Coatings.

The effect of three different cerium salts (Ce(NO3)3.6H2O, CeCl3.7H2O and Ce(OOCCH3)3.5H2O) on the ring-opening polymerization (ROP) of a model diamine-based benzoxazine (4EP-pPDA) was investigated. With the incorporation of the cerium salts, the curing temperature of 4EP-pPDA is reduced substantially, and the glass transition temperatures of the resulting networks are increased significantly. The three cerium salts exhibit different catalytic activities, which were analyzed by FT-IR, NMR, and energy-dispersive X-ray (EDX). Ce(NO3)3.6H2O was found to exhibit the best catalytic effect, which seems to be related to its better dispersibility within 4EP-pPDA benzoxazine precursors.

Melt-processing of cellulose nanofibril/polylactide bionanocomposites via a sustainable polyethylene glycol-based carrier system.

Considering the appealing need for an industrially viable approach, this works aims at demonstrating the rapid and easy melt processing of Polylactide (PLA) bio-composites reinforced with cellulose nanofibrils (CNF). For this purpose and against to their high propensity to self-aggregate on processing, an aqueous CNF-based suspension in the presence of polyethylene glycol (PEG) followed by a gentle drying way were performed to provide melt-processable CNF-based masterbatches. Morphological observations coupled with rheological analyses confirmed how the strategy of the PEG-based masterbatch approach facilitated the formation of a well-dispersed and strongly interacting CNF network within the polymeric matrix. At temperatures above Tg, thermo-mechanical characterization showed that the load-bearing capacity of the web-like CNF network was even more apparent and counteracted the PEG plasticizing effect. Thermogravimetric analysis evidenced that in the case of selective positioning at the PLA-PEG interface, CNF mitigated the negative impact of PEG addition on the PLA thermal stability. These results revealed the successfulness of our sustainable organic solvent-free approach to prepare melt-processable CNF masterbatches, which can be readily converted into conventional industrially scalable melt-processing techniques.

Sealing porous anodic layers on AA2024-T3 with a low viscosity benzoxazine resin for corrosion protection in aeronautical applications.

In this paper, a 4-ethylphenol-para-phenylenediamine (4EP-pPDA) benzoxazine has been applied and cured on previously anodized AA2024-T3 substrates. The porous surface oxide layers obtained from sulfo-tartaric anodizing appeared to be highly impregnated by the benzoxazine resin, sealing the anodic films. Through rheological, morphological and chemical characterization, the curing process has been identified to be the key step for the impregnation to occur, related to the low viscosity of the 4EP-pPDA benzoxazine attained during thermal curing. Moreover, the typical surface porosity of the anodic layer reappeared after curing, offering a good anchoring to possible top coats. Finally, high and enduring barrier properties of this hybrid organic-inorganic layer have been highlighted through Electrochemical Impedance Spectroscopy (EIS) and correlated with recent results obtained by Molecular Dynamics Simulations (MDS). These barrier properties appeared to be strongly influenced by the curing process parameters, as has been assessed using alternative curing cycles limiting their duration and lowering the curing temperature. Consequently, adapting the curing process enables the optimization of the barrier properties of the system while respecting the dependence of the mechanical properties of the AA2024-T3 substrate on thermal treatment at high temperatures.

Do Carbon Nanotubes Improve the Thermomechanical Properties of Benzoxazine Thermosets?

Fillers are widely used to improve the thermomechanical response of polymer matrices, yet often in an unpredictable manner because the relationships between the mechanical properties of the composite material and the primary (chemical) structure of its molecular components have remained elusive so far. Here, we report on a combined theoretical and experimental study of the structural and thermomechanical properties of carbon nanotube (CNT)-reinforced polybenzoxazine resins, as prepared from two monomers that only differ by the presence of two ethyl side groups. Remarkably, while addition of CNT is found to have no impact on the glass-transition temperature ( Tg) of the ethyl-decorated resin, the corresponding ethyl-free composite features a surge by ∼47 °C (50 °C) in Tg, from molecular dynamics simulations (dynamic mechanical analysis measurements), as compared to the neat resin. Through a detailed theoretical analysis, we propose a microscopic picture for the differences in the thermomechanical properties of the resins, which sheds light on the relative importance of network topology, cross-link and hydrogen-bond density, chain mobility, and free volume.

Epoxy Monomers Cured by High Cellulosic Nanocrystal Loading.

The present study focuses on the use of cellulose nanocrystals (CNC) as the main constituent of a nanocomposite material and takes advantage of hydroxyl groups, characteristic of the CNC chemical structure, to thermally cross-link an epoxy resin. An original and simple approach is proposed, based on the collective sticking of CNC building blocks with the help of a DGEBA/TGPAP-based epoxy resin. Scientific findings suggest that hydroxyl groups act as a toxic-free cross-linking agent of the resin. The enhanced protection against water degradation as compared to neat CNC film and the improvement of mechanical properties of the synthesized films are attributed to a good compatibility between the CNC and the resin. Moreover, the preservation of CNC optical properties at high concentrations opens the way to applying these materials in photonic devices.

Facile preparation of a novel high performance benzoxazine-CNT based nano-hybrid network exhibiting outstanding thermo-mechanical properties.

Untreated multi-walled carbon nanotubes (MWCNTs) have been dispersed in two benzoxazine precursors following an easy procedure. The strong intrinsic interactions of CNTs with a selected precursor give rise to the formation of a reinforced network with outstanding thermo-mechanical properties.

High-performance polylactide/ZnO nanocomposites designed for films and fibers with special end-use properties.

Metallic oxides have been successfully investigated for the recycling of polylactide (PLA) via catalyzed unzipping depolymerization allowing for the selective recovery of lactide monomer. In this contribution, a metallic oxide nanofiller, that is, ZnO, has been dispersed into PLA without detrimental polyester degradation yielding PLA/ZnO nanocomposites directly suitable for producing films and fibers. The nanocomposites were produced by melt-blending two different grades of PLA with untreated ZnO and surface-treated ZnO nanoparticles. The surface treatment by silanization proved to be necessary for avoiding the decrease in molecular weight and thermal and mechanical properties of the filled polyester matrix. Silane-treated ZnO nanoparticles yielded nanocomposites characterized by good mechanical performances (tensile strength in the interval from 55 to 65 MPa), improved thermal stability, and fine nanofiller dispersion, as evidenced by microscopy investigations. PLA/ZnO nanocomposites were further extruded in films and fibers, respectively, characterized by anti-UV and antibacterial properties.