Chemical, Electrochemical, and Surface Morphological Studies of the Corrosion Behavior of the AZ31 Alloy in Simulated Body Fluid: Effect of NaOH and H2O2 Surface Pretreatments on the Corrosion Resistance Property.

Magnesium and its alloys have attracted attention for biomedical implant materials in dental and orthopedic applications because of their biodegradability and similar properties to human bones. The very high rate of degradation in the physiological systems is, however, a major setback to their utilization. Chemical modification is one of the approaches adopted to enhance the corrosion resistance property of Mg and its alloys. In this work, NaOH and H2O2 were used as a pretreatment procedure to improve the corrosion resistance of the AZ31 Mg alloy in simulated body fluid (SBF). Advanced techniques such as dynamic electrochemical impedance spectroscopy (dynamic-EIS), atomic force microscopy, and optical profilometry were used in addition to the classical mass loss, hydrogen evolution, EIS, and polarization techniques to study the corrosion resistance property of the alloy in SBF for 30 h. Results obtained show that the surface treatment significantly enhanced the corrosion resistance property of the alloy. From dynamic-EIS at 30 h, the charge transfer resistance of the untreated AZ31 Mg alloy is 432.6 Ω cm2, whereas 822.7 and 2617.3 Ω cm2 are recorded for NaOH- and H2O2-treated surfaces, respectively. H2O2 is a better treatment reagent than NaOH. The mechanism of corrosion of both untreated and treated samples in the studied corrosive medium has been discussed.

Understanding the Corrosion Behavior of the AZ91D Alloy in Simulated Body Fluid through the Use of Dynamic EIS.

Dynamic electrochemical impedance spectroscopy (dynamic EIS) has the capacity to track changes on surfaces in a changing corrosive system, an advantage it holds over classical EIS. We used the dynamic EIS approach to provide insight into the corrosion behavior of the AZ91D Mg alloy in simulated body fluid for 30 h at 25 °C. The results reveal that the impedance response of the alloy is influenced by the immersion time. Between 0 and 7 h, impedance with three time constants was obtained, whereas two-time-constant impedance spectra were obtained between 8 and 30 h of immersion. The results confirm the breakdown of the corrosion product at longer immersion times.

The Improvement of Durability of Reinforced Concretes for Sustainable Structures: A Review on Different Approaches.

The topic of sustainability of reinforced concrete structures is strictly related with their durability in aggressive environments. In particular, at equal environmental impact, the higher the durability of construction materials, the higher the sustainability. The present review deals with the possible strategies aimed at producing sustainable and durable reinforced concrete structures in different environments. It focuses on the design methodologies as well as the use of unconventional corrosion-resistant reinforcements, alternative binders to Portland cement, and innovative or traditional solutions for reinforced concrete protection and prevention against rebars corrosion such as corrosion inhibitors, coatings, self-healing techniques, and waterproofing aggregates. Analysis of the scientific literature highlights that there is no preferential way for the production of "green" concrete but that the sustainability of the building materials can only be achieved by implementing simultaneous multiple strategies aimed at reducing environmental impact and improving both durability and performances.

Effect of Heat Treatment on Microstructure and Selective Corrosion of LPBF-AlSi10Mg by Means of SKPFM and Exo-Electron Emission.

The paper deals with the evolution of the microstructure of AlSi10Mg alloy obtained by laser powder bed fusion (LPBF), as a function of the post-processing heat treatment temperature. This was approached by complementary methods including FE-scanning electron microscopy, scanning Kelvin probe force microscopy and exo-electron emission techniques. The fast cooling rate of the LPBF process as compared to traditional casting produces a very fine microstructure with high mechanical properties and corrosion resistance. However, the LPBF-AlSi10Mg alloy can be susceptible to selective corrosion at the edge of the melt pools generated by the laser scan tracks. Post-process thermal treatments of the Al alloy induce a marked modification of the silicon network at melt pool edges, in particular at high temperature such as 400 °C. It was found that this is associated to a more homogeneous distribution of Volta potential. Analysis of exo-electron emission confirms the silicon diffusion during thermal treatment. The modification of the silicon network structure of the LPBF-AlSi10Mg during thermal treatment reduces the susceptibility to selective corrosion.

Stress Corrosion Cracking of Additively Manufactured Alloy 625.

Laser bed powder fusion (LPBF) is an additive manufacturing technology for the fabrication of semi-finished components directly from computer-aided design modelling, through melting and consolidation, layer upon layer, of a metallic powder, with a laser source. This manufacturing technique is particularly indicated for poor machinable alloys, such as Alloy 625. However, the unique microstructure generated could modify the resistance of the alloy to environment assisted cracking. The aim of this work was to analyze the stress corrosion cracking (SCC) and hydrogen embrittlement resistance behavior of Alloy 625 obtained by LPBF, both in as-built condition and after a standard heat treatment (grade 1). U-bend testing performed in boiling magnesium chloride at 155 and 170 °C confirmed the immunity of the alloy to SCC. However, slow strain rate tests in simulated ocean water on cathodically polarized specimens highlighted the possibility of the occurrence of hydrogen embrittlement in a specific range of strain rate and cathodic polarization. The very fine grain size and dislocation density of the thermally untreated specimens appeared to increase the hydrogen diffusion and embrittlement effect on pre-charged specimens that were deformed at the high strain rate. Conversely, heat treatment appeared to mitigate hydrogen embrittlement at high strain rates, however at the slow strain rate all the specimens showed a similar behavior.

Nanobody-Dependent Detection of Microcystis aeruginosa by ELISA and Thermal Lens Spectrometry.

Nanobodies against cell surface antigens of toxic cyanobacteria Microcystis aeruginosa were recovered by whole-cell biopanning of a naïve phage display library of nanobodies. Six unique sequences were identified and three sub-cloned and purified as fusion immunoreagents together with either green fluorescent protein or AviTag to be used for diagnostics. The yields of nanobody constructs were in the range of 5-10 mg/l and their specificity and sensitivity was initially evaluated by immunofluorescence and by fluorescent enzyme-linked immunosorbent assay (ELISA) using fluorescent nanobodies. The ELISA data confirmed the nanobody specificity but showed that the saturation of the fluorescence signal already in the presence of few hundreds of cells limited the dynamic range of the method. As an alternative, Avi-tagged nanobodies were used in combination with streptavidin-linked horseradish peroxidase for developing a diagnostic colorimetric cell ELISA, the limit-of-detection of which was 3.2 and 4.5 cells/ml for the two tested cyanobacteria strains, whereas the linear range of the assay was expanded from 10 to 10,000 cells. The fluorescent nanobodies were finally exploited for quantifying cyanobacteria by thermal lens spectrometry (TLS) that enabled to reach a limit-of-detection of 1.2 cells/ml and provided a linear range of measurement between 0 and 10,000 cells. No cross-reactivity with unrelated microalgae was detected and both colorimetric ELISA and TLS provided a linear range of detection of few logs. The data indicate that nanobodies are suitable capture reagents and that both TLS and colorimetric ELISA are reliable to monitor variations of cyanobacteria populations.

Effect of Load on the Corrosion Behavior of Friction Stir Welded AA 7075-T6 Aluminum Alloy.

The paper focuses on the corrosion behavior of aluminum joints made by friction stir welding as a function of loading conditions. A four-points bend-beam test, constant loading test, and slow strain-rate test were carried out on AA 7075-T6 alloy in aerated NaCl 35g/L solution at room temperature monitoring the free corrosion potential. The penetration depth of the intergranular attack was deeper after the four-point bent-beam tests compared to all the other testing techniques. Preferential dissolution along the grain boundaries was found in the heat-affected zone and the attack follows the elongated grains structure along the rolling direction. However, no stress-corrosion cracking phenomena were detected. No relevant stress corrosion cracking (SCC) crack embryos propagation was noticed under uniaxial tensile tests-both constant loading and slow strain-rate tests-manly due to the high dissolution rate occurring at the crack tip which promoted premature shear ruptures.

Stress Corrosion Cracking of Friction Stir-Welded AA-2024 T3 Alloy.

The paper is devoted to the study of stress corrosion cracking phenomena in friction stir welding AA-2024 T3 joints. Constant load (CL) cell and slow strain rate (SSR) tests were carried out in aerated NaCl 35 g/L solution. During the tests, open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) were measured in the different zones of the welding. The results evidenced initial practical nobilty of the nugget lower compared to both heat-affected zone and the base metal. This effect can be mainly ascribed to the aluminum matrix depletion in copper, which precipitates in form of copper-rich second phases. In this zones, no stress corrosion cracking was noticed, but well-evident stress-enhanced intergranular corrosion occurred. This is due to the uneven distribution of platic deformation during the slow strain rate tests. Higher strain values are localized at the heat affected zone, where softening occurs. On the contrary, stress values at the nugget are not sufficient to favor both the initiation and propagation of stress corrosion cracks. In the range of processing parameter studied in this experimental work, the stress corrosion cracking susceptibility of the friction stir welding (FSW)-ed alloy is then similar to that of the base metal.

Hydrogen Permeation in X65 Steel under Cyclic Loading.

This experimental work analyzes the hydrogen embrittlement mechanism in quenched and tempered low-alloyed steels. Experimental tests were performed to study hydrogen diffusion under applied cyclic loading. The permeation curves were fitted by considering literature models in order to evaluate the role of trapping-both reversible and irreversible-on the diffusion mechanism. Under loading conditions, a marked shift to the right of the permeation curves was noticed mainly at values exceeding the tensile yield stress. In the presence of a relevant plastic strain, the curve changes due to the presence of irreversible traps, which efficiently subtract diffusible atomic hydrogen. A significant reduction in the apparent diffusion coefficient and a considerable increase in the number of traps were noticed as the maximum load exceeded the yield strength. Cyclic loading at a tensile stress slightly higher than the yield strength of the material increases the hydrogen entrapment phenomena. The tensile stress causes a marked and instant reduction in the concentration of mobile hydrogen within the metal lattice from 55% of the yield strength, and it increases significantly in the plastic field.

Ecological time series and integrative taxonomy unveil seasonality and diversity of the toxic diatom Pseudo-nitzschia H. Peragallo in the northern Adriatic Sea.

Pseudo-nitzschia H. Peragallo (1900) is a globally distributed genus of pennate diatoms that are important components of phytoplankton communities worldwide. Some members of the genus produce the neurotoxin domoic acid, so regular monitoring is in place. However, the identification of toxic members in routine samplings remains problematic. In this study, the diversity and seasonal occurrence of Pseudo-nitzschia species were investigated in the Gulf of Trieste, a shallow gulf in the northern Adriatic Sea. We used time series data from 2005 to 2018 to describe the seasonal and inter-annual occurrence of the genus in the area and its contribution to the phytoplankton community. On average, the genus accounted for about 15 % of total diatom abundance and peaked in spring and autumn, with occasional outbreaks during summer and large inter-annual fluctuations. Increased water temperature and decreased salinity positively affected the presence of some members of the genus, while strong effects could be masked by an unsuitable definition of the species complexes used for monitoring purposes. Therefore, combining morphological (TEM) and molecular analyses by sequencing the ITS, 28S and rbcL markers, eight species were identified from 83 isolated monoclonal strains: P. calliantha, P. fraudulenta, P. delicatissima, P. galaxiae, P. mannii, P. multistriata, P. pungens and P. subfraudulenta. A genetic comparison between the isolated strains and other strains in the Mediterranean was carried out and rbcL was inspected as a potential barcode marker in respect to our results. This is the first study in the Gulf of Trieste on Pseudo-nitzschia time series from a long-term ecological research (LTER) site coupled with molecular data. We show that meaningful ecological conclusions can be drawn by applying integrative methodology, as opposed to the approach that only considers species complexes. The results of this work will provide guidance for further monitoring efforts as well as research activities, including population genetics and genomics, associated with seasonal distribution and toxicity profiles.

Microstructure and Selective Corrosion of Alloy 625 Obtained by Means of Laser Powder Bed Fusion.

The effect of microstructure on the susceptibility to selective corrosion of Alloy 625 produced by laser powder bed fusion (LPBF) process was investigated through intergranular corrosion tests according to ASTM G28 standard. The effect of heat treatment on selective corrosion susceptibility was also evaluated. The behavior was compared to commercial hot-worked, heat treated Grade 1 Alloy 625. The morphology of attack after boiling ferric sulfate-sulfuric acid test according to ASTM G28 standard is less penetrating for LPBF 625 alloy compared to hot-worked and heat-treated alloy both in as-built condition and after heat treatment. The different attack morphology can be ascribed to the oversaturation of the alloying elements in the nickel austenitic matrix obtained due to the very high cooling rate. On as-built specimens, a shallow selective attack of the border of the melt pools was observed, which disappeared after the heat treatment. The results confirmed similar intergranular corrosion susceptibility, but different corrosion morphologies were detected. The results are discussed in relation to the unique microstructures of LPBF manufactured alloys.

Hydrogen Embrittlement Evaluation of Micro Alloyed Steels by Means of J-Integral Curve.

The aim of this work is the evaluation of the hydrogen effect on the J-integral parameter. It is well-known that the micro alloyed steels are affected by Hydrogen Embrittlement phenomena only when they are subjected at the same time to plastic deformation and hydrogen evolution at their surface. Previous works have pointed out the absence of Hydrogen Embrittlement effects on pipeline steels cathodically protected under static load conditions. On the contrary, in slow strain rate tests it is possible to observe the effect of the imposed potential and the strain rate on the hydrogen embrittlement steel behavior only after the necking of the specimens. J vs. Δa curves were measured on different pipeline steels in air and in aerated NaCl 3.5 g/L solution at free corrosion potential or under cathodic polarization at -1.05 and -2 V vs. SCE. The area under the J vs. Δa curves and the maximum crack propagation rate were taken into account. These parameters were compared with the ratio between the reduction of area in environment and in air obtained by slow strain rate test in the same environmental conditions and used to rank the different steels.

In vitro isolation of nanobodies for selective Alexandrium minutum recognition: A model for convenient development of dedicated immuno-reagents to study and diagnostic toxic unicellular algae.

At the present, the identification of planktonic species in coastal water is still a time intensive process performed by highly trained personnel that relies either on qPCR or on light microscopy observation and in vitro culturing. Furthermore, the increasing danger represented by Harmful Algal Blooms (HABs) inside phytoplankton community and the recent implementation of the legislation on ballast water management to prevent the introduction of HABs and NIS (Non Indigenous Species) urge the development of faster and reliable diagnostic methods. Immuno-based approaches could fulfil this need provided that the costs for antibody selection and production will be reduced. In this work it is demonstrated for the first time the feasibility to recover nanobodies (VHHs) selective for native surface epitopes of Alexandrium minutum by direct whole cell bio-panning using a pre-immune phage display library. The recombinant nature of VHHs enabled their rapid engineering into eGFP fluorescent reagents (fluobodies) that were produced recombinantly in bacteria and are directly suitable for fluorescence microscopy and flow cytometry. Immune-detection identified also cysts and anti-Alexandrium fluobodies showed no cross-reactivity with indigenous not-toxic phytoplankton microalgae belonging to different geni. The fluobodies were able to bind selectively to the target cells in both fixed and fresh samples with minimal processing.

Dinoflagellate resting cysts from surface sediments of the Adriatic Ports: Distribution and potential spreading patterns.

The ability of microalgae to preserve viable in coastal sediments as resting forms provides a reservoir of biodiversity and a useful tool to determine species spreadings. This study represents the first port baseline survey on dinoflagellate cysts, investigated in nine Adriatic ports during a cross border project. 40 dinoflagellate taxa were detected. The assemblages resulted in all ports dominated by Lingulodinium polyedra and Alexandrium minutum/affine/tamutum group. General separation to the western and eastern side of the Adriatic regarding cysts assemblage composition, partially abundance, was observed. Six taxa were detected as non-indigenous species for the Adriatic. Two taxa are included in the list of harmful aquatic organisms, indicating the potential threat of ballast waters in the Adriatic. Potential spreading of taxa by general circulation and ballast waters, intra- and extra-Adriatic was investigated. The entering in to force of the ballast waters management regulations should enhance prospects to minimize future harmful impacts.

Phytoplankton diversity in Adriatic ports: Lessons from the port baseline survey for the management of harmful algal species.

An inventory of phytoplankton diversity in 12 Adriatic ports was performed with the port baseline survey. Particular emphasis was put on the detection of harmful aquatic organisms and pathogens (HAOP) because of their negative impact on ecosystem, human health, and the economy. Phytoplanktonic HAOP are identified as species, either native or non-indigenous (NIS), which can trigger harmful algal blooms (HAB). A list of 691 taxa was prepared, and among them 52 were classified as HAB and five as NIS. Records of toxigenic NIS (Pseudo-nitzschia multistriata, Ostreopsis species including O. cf. ovata) indicate that the intrusion of non-native invasive phytoplankton species has already occurred in some Adriatic ports. The seasonal occurrence and abundance of HAOP offers a solid baseline for a monitoring design in ports in order to prevent ballast water uptake and possible expansion of HAOP outside their native region.

Status of faecal pollution in ports: A basin-wide investigation in the Adriatic Sea.

Ports are subject to a variety of anthropogenic impacts, and there is mounting evidence of faecal contamination through several routes. Yet, little is known about pollution in ports by faecal indicator bacteria (FIB). FIB spatio-temporal dynamics were assessed in 12 ports of the Adriatic Sea, a semi-enclosed basin under strong anthropogenic pressure, and their relationships with environmental variables were explored to gain insight into pollution sources. FIB were abundant in ports, often more so than in adjacent areas; their abundance patterns were related to salinity, oxygen, and nutrient levels. In addition, a molecular method, quantitative (q)PCR, was used to quantify FIB. qPCR enabled faster FIB determination and water quality monitoring that culture-based methods. These data provide robust baseline evidence of faecal contamination in ports and can be used to improve the management of routine port activities (dredging and ballast water exchange), having potential to spread pathogens in the sea.

Strategy of port baseline surveys (PBS) in the Adriatic Sea.

Port baseline surveys (PBS) provide species inventories in and around ports, with a focus on non-indigenous species that may have been introduced by vessels, primarily via ballast water. PBS are an essential tool to support effective management strategies for non-indigenous as well as native harmful aquatic organisms and pathogens (HAOP). This paper describes the methodology of PBS that were conducted in 12 Adriatic ports. The PBS employed existing protocols that were adapted to meet the characteristics of the Adriatic sites. Their results are reported in several papers included in this special issue, each of which is devoted to a specific community. An overview of existing surveys protocols - which provide valuable support to decision-making and to design effective monitoring of non-indigenous species - is also supplied.

Binders alternative to Portland cement and waste management for sustainable construction-part 1.

This review presents "a state of the art" report on sustainability in construction materials. The authors propose different solutions to make the concrete industry more environmentally friendly in order to reduce greenhouse gases emissions and consumption of non-renewable resources. Part 1-the present paper-focuses on the use of binders alternative to Portland cement, including sulfoaluminate cements, alkali-activated materials, and geopolymers. Part 2 will be dedicated to traditional Portland-free binders and waste management and recycling in mortar and concrete production.

Binders alternative to Portland cement and waste management for sustainable construction - Part 2.

The paper represents the "state of the art" on sustainability in construction materials. In Part 1 of the paper, issues related to production, microstructures, chemical nature, engineering properties, and durability of mixtures based on binders alternative to Portland cement were presented. This second part of the paper concerns the use of traditional and innovative Portland-free lime-based mortars in the conservation of cultural heritage, and the recycling and management of wastes to reduce consumption of natural resources in the production of construction materials. The latter is one of the main concerns in terms of sustainability since nowadays more than 75% of wastes are disposed of in landfills.

Corrosion Behavior of Heat-Treated AlSi10Mg Manufactured by Laser Powder Bed Fusion.

This experimental work is aimed at studying the effect of microstructural modifications induced by post-processing heat treatments on the corrosion behavior of silicon-aluminum alloys produced by means of laser powder bed fusion (LPBF). The manufacturing technique leads to microstructures characterized by the presence of melt pools, which are quite different compared to casting alloys. In this study, the behavior of an AlSi10Mg alloy was evaluated by means of intergranular corrosion tests according to ISO 11846 standard on heat-treated samples ranging from 200 to 500 °C as well as on untreated samples. We found that temperatures above 200 °C reduced microhardness of the alloy, and different corrosion morphologies occurred due to the modification of both size and distribution of silicon precipitates. Selective penetrating attacks occurred at melt pool borders. The intergranular corrosion phenomena were less intense for as-produced specimens without heat treatments compared to the heat-treated specimens at 200 and 300 °C. General corrosion morphologies were noticed for specimens heat treated at temperatures exceeding 400 °C.