Sulfonated polystyrenes: pH and Mg2+-insensitive amphiphilic copolymers for detergent-free membrane protein isolation.

Amphiphilic polymers are increasingly applied in the detergent-free isolation and functional studies of membrane proteins. However, the carboxylate group present in the structure of many popular variants, such as styrene-maleic acid (SMA) copolymers, brings limitations in terms of polymer sensitivity to precipitation at acidic pH or in the presence of divalent metal cations. Herein, we addressed this problem by replacing carboxylate with the more acidic sulfonate groups. To this end, we synthesized a library of amphiphilic poly[styrene-co-(sodium 4-styrene sulfonate)] copolymers (termed SSS), differing in their molecular weight and overall polarity. Using model cell membranes (Jurkat), we identified two copolymer compositions (SSS-L30 and SSS-L36) that solubilized membranes to an extent similar to SMA. Interestingly, the density gradient ultracentrifugation/SDS-PAGE/Western blotting analysis of cell lysates revealed a distribution of studied membrane proteins in the gradient fractions that was different than for SMA-solubilized membranes. Importantly, unlike SMA, the SSS copolymers remained soluble at low pH and in the presence of Mg2+ ions. Additionally, the solubilization of DMPC liposomes by the lead materials was studied by turbidimetry, DLS, SEC, and high-resolution NMR, revealing, for SSS-L36, the formation of stable particles (nanodiscs), facilitated by the direct hydrophobic interaction of the copolymer phenyls with lipid acyl chains.

Tailoring Butyl Methacrylate/Methacrylic Acid Copolymers for the Solubilization of Membrane Proteins: The Influence of Composition and Molecular Weight.

Low-molecular weight (MW) amphiphilic copolymers have been recently introduced as a powerful tool for the detergent-free isolation of cell membrane proteins. Herein, a screening approach is used to identify a new copolymer type for this application. Via a two-step ATRP/acidolysis procedure, a 3 × 3 matrix of well-defined poly[(butyl methacrylate)-co-(methacrylic acid)] copolymers (denoted BMAA) differing in their MW and ratio of hydrophobic (BMA) and hydrophilic (MAA) units is prepared. Subsequently, using the biologically relevant model (T-cell line Jurkat), two compositions of BMAA copolymers are identified that solubilize cell membranes to an extent comparable to the industry standard, styrene-maleic acid copolymer (SMA), while avoiding the potentially problematic phenyl groups. Surprisingly, while only the lowest-MW variant of the BMA/MAA 2:1 composition is effective, all the copolymers of the BMA/MAA 1:1 composition are found to solubilize the model membranes, including the high-MW variant (MW of 14 000). Importantly, the density gradient ultracentrifugation/sodium dodecyl sulfate-polyacrylamide gel electrophoresis/Western blotting experiments reveal that the BMA/MAA 1:1 copolymers disintegrate the Jurkat membranes differently than SMA, as demonstrated by the different distribution patterns of two tested membrane protein markers. This makes the BMAA copolymers a useful tool for studies on membrane microdomains differing in their composition and resistance to membrane-disintegrating polymers.

MALDI-ToF mass spectrometry detection of intramolecular composition gradient in copolymers.

Since their addition to the polymer-architecture portfolio, gradient copolymers have attracted significant attention. Up to now, however, the existence of the intramolecular composition gradient must have been ascertained by sampling during living copolymerization because a reliable method for the detection of the composition gradient in the finalized copolymer had not been established yet. Here we show that MALDI-ToF mass spectrometry not only identifies imperfect, i.e. prematurely terminated copolymers but these copolymers can be used as "time capsules" which provide information on composition evolution and the intramolecular composition gradient.