Effect of decellularization protocol on the mechanical behavior of porcine descending aorta.

Enzymatic-detergent decellularization treatments may use a combination of chemical reagents to reduce vascular tissue to sterilized scaffolds, which may be seeded with endothelial cells and implanted with a low risk of rejection. However, these chemicals may alter the mechanical properties of the native tissue and contribute to graft compliance mismatch. Uniaxial tensile data obtained from native and decellularized longitudinal aortic tissue samples was analyzed in terms of engineering stress and fit to a modified form of the Yeoh rubber model. One decellularization protocol used SDS, while the other two used TritonX-100, RNase-A, and DNase-I in combination with EDTA or sodium-deoxycholate. Statistical significance of Yeoh model parameters was determined by paired t-test analysis. The TritonX-100/EDTA and 0.075% SDS treatments resulted in relatively variable mechanical changes and did not effectively lyse VSMCs in aortic tissue. The TritonX-100/sodium-deoxycholate treatment effectively lysed VSMCs and was characterized by less variability in mechanical behavior. The data suggests a TritonX-100/sodium-deoxycholate treatment is a more effective option than TritonX-100/EDTA and SDS treatments for the preparation of aortic xenografts and allografts because it effectively lyses VSMCs and is the least likely treatment, among those considered, to promote a decrease in mechanical compliance.

Mechanical properties of human fetal talus.

Mechanical characterization of human cartilage anlagen is required to effectively model congenital musculoskeletal deformities. Such modeling can effectively explore the effect of treatment procedures and potentially suggest enhanced treatment methods. Using serial MRI, we have noted shape changes of the cartilaginous hindfoot anlagen in patients with clubfoot, suggesting they are soft and deformable. We therefore determined the stress relaxation behavior of cartilage plugs obtained from third-trimester stillborn fetuses in unconfined and confined compression geometries. The material parameters determined were the aggregate modulus H(A) = 0.15 +/- 0.07 MPa, Poisson's ratio nu = 0.4 +/- 0.06, Young's modulus E(s) = 0.06 +/- 0.03 MPa, and permeability coefficients k(0) = 2.01 +/- 0.8 x 10(-14) m(4) N(-1) s(-1) and M = 4.6 +/- 1.0. As compared with adult articular cartilage, stiffness was an order of magnitude lower than the values reported in the literature, suggesting the relative softness of the tissue, and the permeability was an order of magnitude higher, indicating relative ease of flow in the tissue. Poisson's ratio also was close to the higher end of the range reported in previous studies. Such material is expected to deform and relax to larger extents. These findings are consistent with the deformability of the cartilage anlagen during manipulation and casting for treatment of clubfoot.

The mechanical properties of crystalline cyclopentyl polyhedral oligomeric silsesquioxane.

The anisotropic elastic constants of crystalline octacyclopentyl polyhedral oligomeric silsesquioxane (CpPOSS) were determined using molecular dynamics. The force field used for these calculations was shown to model accurately the rhombohedral and triclinic crystal structures of octasilsesquioxane and CpPOSS, respectively, as well as the vibrational frequencies of octasilsesquioxane. The moduli for CpPOSS are anisotropic, with a Reuss-averaged bulk modulus of 7.5 GPa, an isotropic averaged Young's modulus of 11.78 GPa, and an isotropic averaged shear modulus of 4.75 GPa. These isotropic averages or, alternatively, the full anisotropic stiffness tensor of the crystal can be used with micromechanical composite models to calculate the effective elastic properties of polymer nanocomposites that contain crystalline aggregates of CpPOSS.

Enhanced mobility accompanies the active deformation of a glassy amorphous polymer.

Molecular dynamics simulation is used to reveal the origin of increased molecular mobility that accompanies plastic deformation of a glassy amorphous polymer under an applied stress. Significant increases in torsional transition rates are observed during active deformation prior to and just beyond the yield point. The transition rate drops when active deformation ceases. Increased transition rates are not contingent upon dilation. These simulations verify recent experimental observations of increased mobility during active deformation.