Ultrasound Pretreatment for Enhancing Fine and Ultrafine Flake Graphite Flotation Beneficiation.

With the severe depletion of coarse flake graphite (a critical raw material) resources, developing and utilizing fine and ultrafine graphite resources have recently attracted attention. Froth flotation is a widely used technique for the initial enrichment of graphite; however, the flotation selectivity decreases significantly along with particle size reduction. Ultrasound pretreatment would be a promising method to improve the flotation of fine particles. As an innovative approach to understand better the flotation response of different flake graphite sizes, this study conducted a comparative analysis based on flotation concentrate yield and ash as well as ash removal rate between the flake graphite with various particle sizes after ultrasound pretreatment. Particle size, X-ray powder diffraction, and scanning electron microscopy and energy dispersive X-ray spectroscopy analyses were used to investigate the effect of ultrasound treatment on mineralogical properties of the flake graphite with varied particle sizes. Process outcomes indicated that the flotation performance of fine flake graphite (mean chord length: 62.63 µm) was significantly enhanced after ultrasound pretreatment. However, flotation of the ultrafine flake graphite (mean chord length: 24.97 µm) after ultrasound treatment was limited due to the difficulty of generating sufficient fragmentation and dissociation by microjets and shock waves formed by the cavitation effect. Compared with conventional flotation, the concentrate yield of ultrasound flotation increased from 88.95 to 94.98%, ash content decreased from 5.72 to 4.87%, and ash removal rate enhanced from 36.94 to 42.61%. Particle size and mineral property analyses confirmed that further crushing and dissociation of the larger flake graphite after ultrasound pretreatment would be the main factors contributing to improved flotation performance. Additionally, the formation of air flocs in the coarse flake graphite during the ultrasound pretreatment process facilitated the flotation recovery of the crushed graphite particles.

Technical and Economic Comparison between Sodium and Ammonium Agents in the Jarosite Precipitation Process-An Evaluation for Industrial Applications.

Iron content can cause severe challenges through zinc production from zinc sulfide concentrate. The zinc industry extensively uses the jarosite precipitation process (JPP) to precipitate dissolved iron and remove it before transferring the solution to downstream stages. Precipitating agents (PAs) play an essential role in the JPP. However, surprisingly, no study compares the efficiency of various PAs on an industrial scale. As an innovative approach, this investigation compares the technical and economic aspects of using various sodium and ammonium compounds (hydroxides, carbonates, bicarbonates, sulfates, and bisulfates) as typical PAs for the JPP at the Bafgh Zinc Smelting Company (BZSC) plant. Experimental results revealed that ammonium hydroxide, with 90.85% iron removal efficiency, had the highest performance, and sodium bisulfate and ammonium bisulfate had the lowest efficiency (74.54 and 77.13%, respectively). However, since ammonium hydroxide is a corrosive PA, it is not a promising alternative to sodium sulfate (with both economic and safety issues). Based on technical and economic assessments, sodium carbonate (84.31% iron removal efficiency) showed the highest potential for an efficient JPP.

Beneficial effects of a polysaccharide-based grinding aid on magnetite flotation: a green approach.

Grinding is the most energy-intensive step in mineral beneficiation processes. The use of grinding aids (GAs) could be an innovative solution to reduce the high energy consumption associated with size reduction. Surprisingly, little is known about the effects of GAs on downstream mineral beneficiation processes, such as flotation separation. The use of ecofriendly GAs such as polysaccharide-based materials would help multiply the reduction of environmental issues in mineral processing plants. As a practical approach, this work explored the effects of a novel polysaccharide-based grinding aid (PGA) on magnetite's grinding and its reverse flotation. Batch grinding tests indicated that PGA improved grinding performance by reducing energy consumption, narrowing particle size distribution of products, and increasing their surface area compared to grinding without PGA. Flotation tests on pure samples illustrated that PGA has beneficial effects on magnetite depression (with negligible effect on quartz floatability) through reverse flotation separation. Flotation of the artificial mixture ground sample in the presence of PGA confirmed the benefits, giving a maximum Fe recovery and grade of 84.4 and 62.5%, respectively. In the absence of starch (depressant), PGA resulted in a separation efficiency of 56.1% compared to 43.7% without PGA. The PGA adsorption mechanism was mainly via physical interaction based on UV-vis spectra, zeta potential tests, Fourier transform infrared spectroscopy (FT-IR), and stability analyses. In general, the feasibility of using PGA, a natural green polymer, was beneficial for both grinding and reverse flotation separation performance.

Pickering emulsion prepared by nano-silica particles - A comparative study for exploring the effect of various mechanical methods.

Pickering emulsions are eco-friendly, stabilized by solid particles, and have an essential role in leading industries. Although Pickering emulations have found several applications, surprisingly few investigations have attempted to explore the effectiveness of various mechanical processes for its production. To fill these gaps, the present investigation comprehensively examined the application of various Pickering emulsion preparation processes such as rotor-stator homogenization emulsification (R-SH), ultrasonic emulsification, and their combined processes by using nano-silica particles. The influences of emulsification time and intensity on emulsion droplets' distribution were analyzed as indicative factors. The kerosene/water nano-silica Pickering emulsion was utilized for all assessments. The obtained results demonstrated that the main distribution peak of the emulsion prepared by R-SH occurred where the chord length was greater than 40 µm. Micro-scale nano-silica-aggregates generated large droplets, while the fine-emulsion fraction was significantly increased after ultrasonic treatment. The experimental results showed that the emulsion prepared only by ultrasound needed substantial power to form a Pickering emulsion since the oil phase was difficult to disperse in the water phase. Finally, it was concluded that preprocessing by R-SH could form a stable and uniform emulsion speedily, which is essential for ultrasound emulsion preparation.

Exploring the Relationships between Gas Dispersion Parameters and Differential Pressure Fluctuations in a Column Flotation.

Flotation separation, which is the most important mineral beneficiation technique, is dependent on gas dispersion (hydrodynamic conditions). Thus, many investigations have focused on the precise determination of hydrodynamic conditions such as Reynolds number of the bubbles, bubble velocity, and bubble diameter. However, few studies have examined their relationships with pressure fluctuations in a column flotation. This study introduced the differential pressure fluctuations as an actual variable that could be considered to determine the collection zone's hydrodynamic conditions in a cyclonic microbubble flotation column. In general, the outcomes indicated that superficial gas velocity had the most substantial relationship with the differential pressure fluctuations among other flotation factors (such as pump speed, superficial gas velocity, superficial water velocity, and frother dosage). Furthermore, a high coefficient of determination (R 2 > 0.77) for the equation generated to assess the relationships demonstrated that differential pressure fluctuations could be used as a promising tool to determine the hydrodynamic parameters' characteristics in the flotation columns.

Effect of the ultrasonic standing wave frequency on the attractive mineralization for fine coal particle flotation.

Froth flotation for mineral beneficiation is one of the most important separation techniques; however, it has several challenges for processing fine and ultrafine particles. Attractive mineralization between particles and bubbles by ultrasonic standing wave (USW) is a novel and high-efficiency method that could assist fine particle flotation. Frequency is an important ultrasound parameter, whose effectiveness mechanisms on the attractive mineralization did not compressively address. This study explored the effect of the USW field with various frequencies on the fine coal flotation for filling this gap. Herein, a high-speed camera and a focused beam reflectance measurement (FBRM) were used to analyze three sub-processes of the attractive mineralization, including the microbubbles' formation, the conventional flotation bubbles (CFBs)' dispersion, and the particles' movement. It was found that the maximum flotation metallurgical responses were obtained under the highest examined USW frequency (600 kHz). However, the flotation outcomes by a low USW frequency (50 kHz) were even lower than the conventional flotation tests. Observation and theoretical calculation results revealed these results were originated from the influence of frequency on the carrier bubbles' formation and the action of the secondary acoustic force during USW-assisted flotation. These outcomes demonstrated that frequency is a key factor determining the success of attractive mineralization for fine particles' flotation.

Nanobubble-Assisted Flotation of Apatite Tailings: Insights on Beneficiation Options.

Processing of materials that originated from tailings of industrial plants (with a wide range of particle size distribution, "PSD") without grinding has several advantages since mines are faced with a lot of pressure to minimize their environmental impacts. This article indicates that the introduction of submicron bubbles (known as nanobubbles, "NBs") to conventional flotation could improve the separation efficiency of valuable minerals from their associated gangue phases. It was demonstrated that metallurgical responses (recovery, grade, selectivity, and kinetics) of NB flotation could improve compared to those of conventional tests. Various hydrodynamic cavitation setups for NB generation may lead to different metallurgical responses. In general, the addition of surfactants (frothers and collectors) for NB generation could increase both mass and water recoveries, which would be key factors on selectivity. Selectivity is also markedly dependent on the PSD of feed, and the selectivity of NB flotation is improved significantly by decreasing the feed size. In general, generation of NBs in the presence of a frother leads to higher flotation metallurgical responses than in the presence of a collector.

Effects of Operational Parameters on the Low Contaminant Jarosite Precipitation Process-an Industrial Scale Study.

Jarosite precipitation process (JPP) is the most frequently used procedure for iron removal in the hydrometallurgical zinc extraction process. However, there is a gap in the knowledge of the relationship between operational parameters and the low contaminant JPP on the industrial scale. This study will address these issues by investigating the behavior of zinc calcine (ZC) as a neutralizing agent, exploring the source of zinc and iron through leaching experiments, and simulating the Jarosite process of the Bafgh Zinc Smelting Company (BZSC). The results showed that the zinc dissolution efficiency was 90.3% at 90 °C, and 73% of the iron present in the calcine can be solubilized. The main outcome was the iron removal of about 85% by alkaline ions present in ZC without the addition of any precipitating agent. The second target was to evaluate the effect of operational parameters on jarosite precipitation. Results revealed that increasing the temperature to 90 °C and the stirring rate to 500 RPM as well as adjusting the ZC's pH during the jarosite precipitation remarkably improved iron removal. Considering all these factors in the plant could improve Fe precipitation to around 80% on average.