A New Integrated GDL with Wavy Channel and Tunneled Rib for High Power Density PEMFC at Low Back Pressure and Wide Humidity.

Proton exchange membrane fuel cells (PEMFCs) have garnered significant attention due to their high efficiency and low emissions. However, PEMFC always suffers mass transfer and water management in performance improvement. Herein, an integrated gas diffusion layer (GDL) with wavy channel and micro-tunneled rib is designed and prepared to achieve faster and gentler mass transfer and excellent water management capability by laser engraving. Outstandingly, the new integrated GDL can use the back pressure of air as low as 0 and 50 kPa to respectively achieve 80% and 90% of fuel cell performance realized under pure oxygen. Such high performance is mainly due to the turbulent flow caused by wavy channel and express removing pathway of liquid water provided by micro-tunneled rib. Moreover, the new integrated GDL also shows wide humidity tolerance from 40% to 100% and a very high specific volume power density of 16,300 W L-1 due to the thin thickness of new integrated GDL. This new integrated GDL is expected to be widely used in PEMFC and other energy conversion devices.

Ordered Membrane Electrode Assembly with Drastically Enhanced Proton and Mass Transport for Proton Exchange Membrane Water Electrolysis.

In this work, an ordered membrane electrode assembly (MEA) based on a cone Nafion array with gradient Nafion distribution, tightly bonded catalytic layer/proton exchange membrane (CL/PEM) interface, and abundant vertical channels has been engineered by an anodic aluminum oxide template and magnetron sputtering method. Benefiting from a highly efficient CL/PEM interface, plentiful proton transfer highways, and rapid oxygen bubble release, this ordered MEA achieves an ultralow Ir loading of 20.0 µg cm-2 and a high electrochemical active area by 8.7 times compared to traditional MEA with Ir loading of 1.0 mg cm-2. It yields a mass activity of 168 000 mA mgIr-1 cm-2 at 2.0 V, which is superior to most reported PEM electrolyzers. Notably, this ordered MEA maintains excellent durability at a current density of 500 mA cm-2. This work opens a simple, cost-effective, and scalable route to design ordered MEAs for proton exchange membrane water electrolysis.

Multiscale Architectured Nafion Membrane Derived from Lotus Leaf for Fuel Cell Applications.

Hierarchically patterned proton-exchange membranes (PEMs) have the potential to significantly increase the specific surface area, thus improving the catalyst utilization rate and performance of proton-exchange membrane fuel cells (PEMFCs). In this study, we are inspired by the unique hierarchical structure of the lotus leaf and proposed a simple three-step strategy to prepare a multiscale structured PEM. Using the multilevel structure of the natural lotus leaf as the original template, and after structural imprinting, hot-pressing, and plasma-etching steps, we successfully constructed a multiscale structured PEM with a microscale pillar-like structure and a nanoscale needle-like structure. When applied in a fuel cell, the multiscale structured PEM resulted in a 1.96-fold increase in discharge performance and a significant improvement in mass transfer compared to the membrane electrode assembly (MEA) with a flat PEM. The multiscale structured PEM has the combined advantage of a nanoscale and a microscale structure, benefiting from the markedly reduced thickness, increased surface area, and improved water management inherited from the multiscale structured lotus leaf's superhydrophobic characteristic. Using a lotus leaf as a multilevel structure template avoids the complex and time-consuming preparation process required by commonly used multilevel structure templates. Moreover, the remarkable architecture of biological materials can inspire novel and innovative applications in many fields through nature's wisdom.

Nanosized Proton Conductor Array with High Specific Surface Area Improves Fuel Cell Performance at Low Pt Loading.

The use of ordered catalyst layers, based on micro-/nanostructured arrays such as the ordered Nafion array, has demonstrated great potential in reducing catalyst loading and improving fuel cell performance. However, the size (diameter) of the basic unit of the most existing ordered Nafion arrays, such as Nafion pillar or cone, is typically limited to micron or submicron sizes. Such small sizes only provide a limited number of proton transfer channels and a small specific area for catalyst loading. In this work, the ordered Nafion array with a pillar diameter of only 40 nm (D40) was successfully prepared through optimization of the Nafion solvent, thermal annealing temperature, and stripping mode from the anode alumina oxide (AAO) template. The density of D40 is 2.7 × 1010 pillars/cm2, providing an abundance of proton transfer channels. Additionally, D40 has a specific area of up to 51.5 cm2/cm2, which offers a large area for catalyst loading. This, in turn, results in the interface between the catalyst layer and gas diffusion layer becoming closer. Consequently, the peak power densities of the fuel cells are 1.47 (array as anode) and 1.29 W/cm2 (array as cathode), which are 3.3 and 2.9 times of that without array, respectively. The catalyst loading is significantly reduced to 17.6 (array as anode) and 61.0 µg/cm2 (array as cathode). Thus, the nanosized Nafion array has been proven to have high fuel cell performance with low Pt catalyst loading. Moreover, this study also provides guidance for the design of a catalyst layer for water electrolysis and electrosynthesis.

A Recyclable Standalone Microporous Layer with Interpenetrating Network for Sustainable Fuel Cells.

The commercialization of fuel cells inevitably brings recycling problems. Therefore, achieving high recyclability of fuel cells is particularly important for their sustainable development. In this work, a recyclable standalone microporous layer (standalone MPL) with interpenetrating network that can significantly enhance the recyclability and sustainability of fuel cells is prepared. The interpenetrating network enables the standalone MPL to have high strength (17.7 MPa), gas permeability (1.55 × 10-13  m2 ), and fuel-cell performance (peak power density 1.35 W cm-2 ), providing the basic guarantee for its application in high-performance and highly recyclable fuel cells. Additionally, the standalone MPL is highly adaptable to various gas-diffusion backings (GDBs), providing high possibility to select highly recyclable GDBs. Outstandingly, anode standalone MPLs and GDBs can be easily detached from the spent membrane electrode assembly (MEA). This not only saves >90 vol% solvent in the recovery of the catalyst-coated membrane (CCM), but also extends the service life of the GDBs and the anode standalone MPL at least 138 times (2 760 000 h assuming 20 000 h of CCM) comparing to CCM. Therefore, the standalone MPL significantly enhances the recyclability and sustainability of fuel cells and is promising to be an indispensable component in the next-generation fuel cells.

Integrated Gas Diffusion Electrode with High Conductivity Obtained by Skin Electroplating for High Specific Power Density Fuel Cell.

Smaller volume/weight and higher output power/energy density are always the goals of electrochemistry energy devices. Here, a simple strategy is proposed to prepare an integrated gas diffusion electrode (GDE) with high conductivity through skin electroplating. The skin electroplating is the combination of magnetron sputtering and spatial confinement electroplating. The electroplated metal obtained by skin electroplating is uniformly, continuously, and tightly attached to the surface of carbon paper like a layer of skin. Uniform and continuous electroplating metal layer endows the integrated electrode excellent conductivity with the square resistance as low as 27 mΩ sq-1 . In application, the self-breathing fuel cell with 1 cm2 active area can harvest ultrahigh volume specific power density (20.9 kW L-1 ). Additionally, the weight of the fuel cell stack (23 W) with the integrated electrode is only 20 g, which is only 7% of the commercial stack with the same power. The mass specific power density reaches 1150 W kg-1 , which is 15 times of the commercial stack. Outstandingly, the stack can charge 4 mobile phones at the same time. More importantly, the skin electroplating provides an effective strategy to improve the specific power density of other energy devices including Zn-air batteries, Li-air batteries, and so on.

Mesenchymal stem cell therapy in pulmonary fibrosis: a meta-analysis of preclinical studies.

BACKGROUND: Pulmonary fibrosis (PF) is a devastating disease characterized by remodeling of lung architecture and abnormal deposition of fibroblasts in parenchymal tissue and ultimately results in respiratory failure and death. Preclinical studies suggest that mesenchymal stem cell (MSC) administration may be a safe and promising option in treating PF. The objective of our meta-analysis is to assess the efficacy of MSC therapy in preclinical models of PF. METHODS: We performed a comprehensive literature search in PubMed, EMBASE, Web of Science, and Cochrane Library databases from inception to March 17, 2021. Studies that assessed the efficacy of MSC therapy to animals with PF were included. The SYRCLE bias risk tool was employed to evaluate the bias of included studies. The primary outcomes included survival rate and pulmonary fibrosis scores. Meta-analysis was conducted via Cochrane Collaboration Review Manager (version 5.4) and Stata 14.0 statistical software. RESULTS: A total of 1120 articles were reviewed, of which 24 articles met inclusion criteria. Of these, 12 studies evaluated the survival rate and 20 studies evaluated pulmonary fibrosis scores. Compared to the control group, MSC therapy was associated with an improvement in survival rate (odds ratios (OR) 3.10, 95% confidence interval (CI) 2.06 to 4.67, P < 0.001, I2 = 0%) and a significant reduction in pulmonary fibrosis scores (weighted mean difference (WMD) 2.05, 95% CI -2.58 to -1.51, P < 0.001, I2 = 90%). CONCLUSIONS: MSC therapy is a safe and effective method that can significantly improve the survival and pulmonary fibrosis of PF animals. These results provide an important basis for future translational clinical studies.

Aryl-indolyl maleimides as inhibitors of CaMKIIdelta. Part 3: Importance of the indole orientation.

A family of aryl-substituted maleimides was prepared and studied for their activity against calmodulin dependant kinase. Inhibitory activities against the enzyme ranged from 10nM to >20microM and were dependant upon both the nature of the aryl group and the tether joining the basic amine to the indolyl maleimide core of the inhibitors. Key interactions with the kinase ATP site and hinge region, predicted by homology modeling, were confirmed.

Pyrimidine-based inhibitors of CaMKIIdelta.

Non-ATP competitive pyrimidine-based inhibitors of CaMKIIdelta were identified. Computational studies were enlisted to predict the probable mode of binding. The results of the computational studies led to the design of ATP competitive inhibitors with optimized hinge interactions. Inhibitors of this class possessed improved enzyme and cellular activity compared to early leads.

Aryl-indolyl maleimides as inhibitors of CaMKIIdelta. Part 1: SAR of the aryl region.

A family of aryl-substituted maleimides was prepared and studied for their activity against calmodulin dependant kinase. Inhibitory activities against the enzyme ranged from 34nM to >20microM and were dependant upon both the nature of the aryl group and the hydrogen bond donating potential of the maleimide ring. Key interactions with the kinase ATP site and hinge region were found to be consistent with homology modeling predictions.

Aryl-indolyl maleimides as inhibitors of CaMKIIdelta. Part 2: SAR of the amine tether.

A family of aryl-substituted maleimides was prepared and studied for their activity against calmodulin-dependant kinase. Inhibitory activities against the enzyme ranged from 34nM to >20microM and were dependant upon both the nature of the aryl group and the tether joining the basic amine to the indolyl maleimide core. Key interactions with the kinase ATP site and hinge region, predicted by homology modeling, were confirmed.

Design and synthesis of tri-ring P3 benzamide-containing aminonitriles as potent, selective, orally effective inhibitors of cathepsin K.

We have prepared a series of achiral aminoacetonitriles, bearing tri-ring benzamide moieties and an aminocyclohexanecarboxylate residue at P2. This combination of binding elements resulted in sub-250 pM, reversible, selective, and orally bioavailable cathepsin K inhibitors. Lead compounds displayed single digit nanomolar inhibition in vitro (of rabbit osteoclast-mediated degradation of bovine bone). The best compound in this series, 39n (CRA-013783/L-006235), was orally bioavailable in rats, with a terminal half-life of over 3 h. 39n was dosed orally in ovariectomized rhesus monkeys once per day for 7 days. Collagen breakdown products were reduced by up to 76% dose-dependently. Plasma concentrations of 39n above the bone resorption IC50 after 24 h indicated a correlation between functional cellular and in vivo assays. Inhibition of collagen breakdown by cathepsin K inhibitors suggests this mechanism of action may be useful in osteoporosis and other indications involving bone resorption.