Wireless Intelligent Patch for Closed-loop In Situ Wound Management.

Wound infections pose a major healthcare issue, affecting the well-being of millions of patients worldwide. Effective intervention and on-site detection are important in wound management. However, current approaches are hindered by time-consuming analysis and a lack of technology for real-time monitoring and prompt therapy delivery. In this study, a smart wound patch system (SWPS) designed for wireless closed-loop and in-situ wound management is presented. The SWPS integrates a microfluidic structure, an organic electrochemical transistor (OECT) based sensor, an electrical stimulation module, and a miniaturized flexible printed circuit board (FPCB). The OECT incorporates a bacteria-responsive DNA hydrogel-coated gate for continuous monitoring of bacterial virulence at wound sites. Real-time detection of OECT readings and on-demand delivery of electrical cues to accelerate wound healing is facilitated by a mobile phone application linked with an FPCB containing low-power electronics equipped with parallel sensing and stimulation circuitry. In this proof-of-concept study, the functionality of the SWPS is validated and its application both in vitro and in vivo is demonstrated. This proposed system expands the arsenal of tools available for effective wound management and enables personalized treatment.

The effectiveness and feasibility of ball-milled powdered activated carbon (BPAC) for removal of organic pesticides in conventional drinking water treatment process.

In the conventional drinking water treatment process (CDWTP), powdered activated carbon (PAC) is commonly used for removing organic pesticides, or other organic contaminants. However, the hydraulic retention time (HRT) in CDWTP is insufficient for fulfilling PAC adsorption equilibrium to realize its full capacity. This study examined the adsorption kinetics, adsorption thermal dynamics, and removal efficiency for six organic pesticides using the ball-milled PAC (BPAC) with varying particle sizes in CDWTP. Based on the experiments with the pesticides of atrazine, diazinon, dimethoate, fenitrothion, isoproturon and thiometon, the results indicated that as the particle size reduced from around 38 µm for the commercial PAC to 1 µm for the BPAC, the adsorption rates for hydrophobic pesticides increased up to twentyfold. Diffusional adsorption from the bulk solution to the external PAC surface is the most likely predominant mechanism. This could allow a sufficient pesticides' adsorption within the limited HRT and to achieve a great depth removal of these toxic compounds. However, the addition of BPAC with a diameter of 1 µm was observed to significantly increase residual particles in treated water after the conventional treatment process. With a further systematic evaluation of both adsorption rate and particle penetration, a particle size of around 6 µm BPAC was considered a practical compromise between the adsorption rate and particle penetration for real application. Results from five surface waters of different water quality indicated that, compared to commercial PAC, application of 6 µm BPAC could achieve up to a 75% reduction in adsorbent dosage while maintaining around the same pesticide removal efficiencies. Additionally, thermodynamic analyses suggest that adsorption of these pesticides could be enthalpically or entropically driven depending on the degree of pesticide hydrophobicity.

Research progress of vanadium pentoxide photocatalytic materials.

Photocatalytic reactions convert solar energy into chemical energy through a clean and green reaction process. Photocatalytic technology based on semiconductor materials provides us with a new idea in energy utilization and environmental governance. It was found that vanadium pentoxide (V2O5) has a narrow band gap, wide response range in the visible region, high oxygen density in the V2O5 lattice, high oxidation state of V5+, small energy requirement, and superior catalytic activity in partial oxidation. Therefore, the utilization rate of sunlight and photocatalytic oxidation can be greatly improved using V2O5 materials. However, the narrow band gap of V2O5 also makes it easier for the photogenerated electrons and holes to recombine in the excited state, and the stored energy is instantly consumed by carrier recombination. Therefore, how to promote the carrier separation of V2O5 and improve the photocatalytic efficiency are the key problems to be solved. Herein, several methods to improve the photocatalytic performance of V2O5 are reviewed, including metallic ion doping, non-metallic ion doping, semiconductor recombination, and noble metal deposition. Finally, it is suggested that future research directions should focus on a variety of modification methods simultaneously to promote photocatalytic efficiency and lower the cost, which will enable V2O5 to have a broad development prospect in the field of photocatalysis.