RESUMEN
To date, it has remained challenging to realize electrically injected light sources in the vacuum ultraviolet wavelength range (â¼200 nm or shorter), which are important for a broad range of applications, including sensing, surface treatment, and photochemical analysis. In this Letter, we have demonstrated such a light source with molecular beam epitaxially grown aluminum nitride (AlN) nanowires on low cost, large area Si substrate. Detailed angle dependent electroluminescence studies suggest that, albeit the light is TM polarized, the dominant light emission direction is from the nanowire top surface, that is, along the c axis, due to the strong light scattering effect. Such an efficient surface emitting device was not previously possible using conventional c-plane AlN planar structures. The AlN nanowire LEDs exhibit an extremely large electrical efficiency (>85%), which is nearly ten times higher than the previously reported AlN planar devices. Our detailed studies further suggest that the performance of AlN nanowire LEDs is predominantly limited by electron overflow. This study provides important insight on the fundamental emission characteristics of AlN nanowire LEDs and also offers a viable path to realize an efficient surface emitting near-vacuum ultraviolet light source through direct electrical injection.
RESUMEN
The current LED lighting technology relies on the use of a driver to convert alternating current (AC) to low-voltage direct current (DC) power, a resistive p-GaN contact layer to inject positive charge carriers (holes) for blue light emission, and rare-earth doped phosphors to down-convert blue photons into green/red light, which have been identified as some of the major factors limiting the device efficiency, light quality, and cost. Here, we show that multiple-active region phosphor-free InGaN nanowire white LEDs connected through a polarization engineered tunnel junction can fundamentally address the afore-described challenges. Such a p-GaN contact-free LED offers the benefit of carrier regeneration, leading to enhanced light intensity and reduced efficiency droop. Moreover, through the monolithic integration of p-GaN up and p-GaN down nanowire LED structures on the same substrate, we have demonstrated, for the first time, AC operated LEDs on a Si platform, which can operate efficiently in both polarities (positive and negative) of applied voltage.
RESUMEN
Despite broad interest in aluminum gallium nitride (AlGaN) optoelectronic devices for deep ultraviolet (DUV) applications, the performance of conventional Al(Ga)N planar devices drastically decays when approaching the AlN end, including low internal quantum efficiencies (IQEs) and high device operation voltages. Here we show that these challenges can be addressed by utilizing nitrogen (N) polar Al(Ga)N nanowires grown directly on Si substrate. By carefully tuning the synthesis conditions, a record IQE of 80% can be realized with N-polar AlN nanowires, which is nearly ten times higher compared to high quality planar AlN. The first 210 nm emitting AlN nanowire light emitting diodes (LEDs) were achieved, with a turn on voltage of about 6 V, which is significantly lower than the commonly observed 20 - 40 V. This can be ascribed to both efficient Mg doping by controlling the nanowire growth rate and N-polarity induced internal electrical field that favors hole injection. In the end, high performance N-polar AlGaN nanowire LEDs with emission wavelengths covering the UV-B/C bands were also demonstrated.
RESUMEN
In this paper, we have investigated the effect of rolled-up nanotubes on the light extraction efficiency of GaN-based LEDs using two-dimensional finite element method simulation. The light extraction involves two successive steps, including the coupling from the light source to the tube and the subsequent emission from the tube to the air. Significantly enhanced light extraction efficiency is observed for both TE and TM waves by optimizing the nanotube geometry and dimension as well as the separation between the nanotube and light source. We have further shown that densely packed nanotube arrays can be integrated with GaN-based LEDs to achieve unequivocal improvement of light extraction efficiency over a large surface area. With recent advances in rolled-up micro- and nanotubes, it is expected that this study can offer a potentially flexible, low cost approach to enhance the light extraction of various LED devices.
RESUMEN
We present a photonic-crystal (PC) channel-drop filter (CDF) design based on 3x3 PC ring resonators. The normalized transmission spectra for single-ring and dual-ring configurations have been investigated using two-dimensional finite-difference time-domain (FDTD) technique in a square-lattice dielectric-rod PC structure. First, we investigate a single ring and we show that backward and forward dropping is possible in the third communication window. Then we add another ring and waveguide to develop a new CDF. This filter consists of an input and three outputs. Our FDTD simulation yields more than 85% efficiency over each output port.
