Research Progress of Preparation Technology of Ion-Exchange Resin Complexes.

As insoluble polymer materials, ion-exchange resins (IERs) can exchange their own ions with desirable charged ions in the solution. According to the affinity of active moieties for soluble counterions, IERs could be categorized into the following four types: strongly acidic cation, weakly acidic cation, strongly basic anion, and weakly basic anion exchange resins. Due to their relative safety and high drug-loading capacity, IERs have garnered extensive attention in the pharmaceutical field since the 1950s. As numerous investigations combine drugs with IERs, this article summarizes the technologies employed in these studies from four aspects: IER screening principles, combining technologies, characterization methods, and in vitro and in vivo release of drug-resinate complexes. In addition, the advantages and disadvantages of various technologies and their scope are expounded. The article provides new insights on the preparation of ion-exchange resin complexes.

[Stability research of Xiaoer Ganmaoning Oral Liquid based on chromatographic peak matching and image sensory evaluation].

The high performance liquid chromatography(HPLC) characteristic chromatogram of Xiaoer Ganmaoning Oral Liquid(oral liquid for short) was established. The medicinal materials corresponding to characteristic peaks, their index components and ranges of similarity with the reference chromatograms were clarified. The similarity between the characteristic chromatograms of 10 batches of the oral liquid and the reference chromatogram was higher than 0.994. Eighteen characteristic peaks were identified, which were derived from different medicinal materials including Scutellariae Radix, Arctii Fructus, Lonicerae Japonicae Flos, Gardeniae Fructus and Forsythiae Fructus. Further, 11 characteristic peaks were assigned by the comparison with reference substances as chlorogenic acid, neochlorogenic acid, cryptochlorogenic acid, isochlorogenic acid A, isochlorogenic acid C, baicalin, baicalein, wogonin, scutellarin, forsythiaside A and arctiin. Also, the characteristic chromatogram of precipitate in the oral liquid was established, and the similarity between characteristic chromatograms of 10 batches of the precipitate and the reference chromatogram was higher than 0.940. The 14 characteristic peaks originating from the precipitate and those from the oral liquid were consistent in retention time, and the content of all index components in the precipitate was lower than 5% of that in the oral liquid. Moreover, the stability of precipitate during the accelerated stability test was explored with filtration and Matlab-based image sensory evaluation. The precipitate mass and precipitation degree both increased over the stability test duration significantly. The stability of the oral liquid was used as a model system in this study to establish the integrated quality control system which related to medicinal materials, preparations and precipitate with HPLC characteristic chromatograms and image sensory evaluation, which lays a foundation for the exploration of the quantity value transfer of the oral liquid.

Empirical prediction model based process optimization for droplet size and spraying angle during pharmaceutical fluidized bed granulation.

The objective of this study was to predict the droplet size and the spraying angle during the process of binder atomization in pharmaceutical fluidized bed granulation using an empirical model. The effects of the binder viscosity, the atomization pressure, and the spray rate on the droplet size and the spraying angle were investigated using a response surface central composite design and analysis of variance. Prediction models for droplet size and spraying angle were then established using stepwise regression analysis and were validated by comparing the measured and predicted values. The results showed that the droplet size model and the spraying angle model were well established, with an R2 of 0.93 (p < 0.0001) and a root mean square error (RMSE) of 10.10, and an R2 of 0.82 (p < 0.0001) and an RMSE of 3.69, respectively. The error between the measured and predicted values of the droplet size and the spraying angle were less than 10%, indicating that the established models were accurate. The results of the present study were significant in predicting the droplet size and spraying angle in the process of pharmaceutical fluidized bed granulation.

[Correlation between chemical compositions of traditional Chinese medicine extracts and phenomenon of wall stickiness in spray drying].

To explore the correlation between chemical compositions (organic acids, small molecule sugars, protein and others) of traditional Chinese medicine extracts and the wall stickiness in spray drying. In this study, 55 types of most common used Chinese herbs were selected to determine the content of 7 chemical components such as citric acid and fructose from plant extraction. The status of wall stickiness was observed during the drying process. The principle component analysis (PCA-X), hierarchical clustering analysis(HCA) and orthogonal partial least squares-discriminant analysis (OPLS-DA) were then used to evaluate the correlation between each chemical compositions and wall stickiness, so as to look for the essential chemical compositions associated with the wall stickiness. All of the above 3 statistical analysis methods showed significant results in distinguishing the two groups (sticky or non-sticky). PCA-X score chart and HCA clustering scatter plot suggested that the small molecular substance was the main factor causing wall stickiness, which was then proved by the reality where some of the traditional herb extracts were in non-sticky state after drying but in sticky state after alcohol precipitation. OPLS-DA results revealed that L-malic acid, citric acid, fructose and glucose were the difference factors for the wall stickiness of the extracts. Under small molecular components, L-malic acid, citric acid, fructose and glucose were the crucial factors that directly led to the hot melt sticky wall of the herbal extracts, and macromolecular substances might ameliorate the function of wall stickiness.

[Discussion on research and development of new traditional Chinese medicine preparation process based on idea of QbD].

Traditional processes are mostly adopted in traditional Chinese medicine (TCM) preparation production and the quality of products is mostly controlled by terminal. Potential problems of the production in the process are unpredictable and is relied on experience in most cases. Therefore, it is hard to find the key points affecting the preparation process and quality control. A pattern of research and development of traditional Chinese medicine preparation process based on the idea of Quality by Design (QbD) was proposed after introducing the latest research achievement. Basic theories of micromeritics and rheology were used to characterize the physical property of TCM raw material. TCM preparation process was designed in a more scientific and rational way by studying the correlation among enhancing physical property of raw material, preparation process and product quality of preparation. So factors affecting the quality of TCM production would be found out and problems that might occur in the pilot process could be predicted. It would be a foundation for the R&D and production of TCM preparation as well as support for the "process control" of TCMIs gradually realized in the future.

[Correlation of dry granulation process parameters and granule quality based on multiple regression analysis].

In this paper, microcrystalline cellulose WJ101 was used as a model material to investigate the effect of various process parameters on granule yield and friability after dry granulation with a single factor and the effect of comprehensive inspection process parameters on the effect of granule yield and friability, then the correlation between process parameters and granule quality was established. The regress equation was established between process parameters and granule yield and friability by multiple regression analysis, the affecting the order of the size of the order of the process parameters on granule yield and friability was: rollers speed > rollers pressure > speed of horizontal feed. Granule yield was positively correlated with pressure and speed of horizontal feed and negatively correlated rollers speed, while friability was on the contrary. By comparison, fitted value and real value, fitted and real value are basically the same of no significant differences (P > 0.05) and with high precision and reliability.