Comprehensive study of retention influencing gas chromatographic parameters affecting linear retention indices.

Retention in gas chromatographic systems has a central role in the identification of compounds even if detectors providing spectral information are used. But linear retention indices (LRI) of a single compound originating from multiple sources tend to vary greatly, probably due to differences in the experimental settings of the determinations. The effect of gas chromatographic parameters on LRI has been investigated using 41 compounds - previously identified from food contact plastics - and n-alkanes (n-C7-n-C40) used as reference series. As the reproducibility of LRIs under the same conditions is generally very good, the smallest changes in the settings often caused statistically significant, though irrelevant changes in the LRI values. Therefore, a multicriterial scoring-ranking system has been worked out to highlight the LRI value differences. Our results highlight that column length, heating rate, and film thickness can all be the reasons of the varying published LRI values. We also demonstrated that for the reproduction of LRI data, the chemistry (and not simply the polarity) of the stationary phase is crucial.

Exploitation of the enantioselectivity space of coated amylose tris(3,5-dimethylphenylcarbamate) in mixtures of 2-propanol and acetonitrile.

Chiral stationary phases (CSPs) with coated amylose tris(3,5-dimethylphenylcarbamate) (ADMPC) selector have long been recognized for their excellent chiral recognition ability in liquid chromatography. The conformational versatility behind this feature is the source of their known hysteretic behavior, which has been previously observed in polar organic (PO) mode eluents containing 2-propanol (IPA). Mixtures of IPA and acetonitrile (MeCN), a typical PO mode eluent system, have not been examined in this aspect yet, even though hysteresis is promising for finding unique unexplored enantioselectivities. Not only was the hysteresis detectable on ADMPC using mixtures of IPA and MeCN, but it was the typical behavior in a diverse set of test compounds. The difference in the retention time of the same analyte under conditions which only differed in the eluent history on the column can go up to 20-fold. The assumed hindered conformational changes of the selector were reflected in retention drift at certain eluent compositions. On the two sides of the transitions, distinct, useful states of the selector were detected. A series of IPA - MeCN compositions with defined pretreatment was selected and recommended as an extension of the preliminary, first choice method screening set that used only alcohols. The incorporation of a solvent possessing substantially different characteristics enhances the potential in practical applications, while keeping the technical simplicity. Stability and robustness of the additional states of the CSP were characterized. The examined columns of different brands shared the observed behavior. Kinetic stability of a column state is adequate for successful application. The evaluated states of ADMPC provide multiple enantiorecognition potential by using mixtures of IPA and MeCN also considering the pretreatment of the column. Unprecedented double and triple elution order reversals along the composition range supported the versatility of the available states. Our findings further enhance the usefulness of ADMPC-containing CSPs. We provide instructions for the application of the widespread chiral selector in common eluent mixtures to avoid pitfalls regarding reproducibility and robustness.

Oligonucleotide Formulations Prepared by High-Speed Electrospinning: Maximizing Loading and Exploring Downstream Processability.

The aim of this study was to develop antisense oligonucleotide tablet formulations using high-speed electrospinning. Hydroxypropyl-beta-cyclodextrin (HPßCD) was used as a stabilizer and as an electrospinning matrix. In order to optimize the morphology of the fibers, electrospinning of various formulations was carried out using water, methanol/water (1:1), and methanol as solvents. The results showed that using methanol could be advantageous due to the lower viscosity threshold for fiber formation enabling higher potential drug loadings by using less excipient. To increase the productivity of electrospinning, high-speed electrospinning technology was utilized and HPßCD fibers containing 9.1% antisense oligonucleotide were prepared at a rate of ~330 g/h. Furthermore, to increase the drug content of the fibers, a formulation with a 50% drug loading was developed. The fibers had excellent grindability but poor flowability. The ground fibrous powder was mixed with excipients to improve its flowability, which enabled the automatic tableting of the mixture by direct compression. The fibrous HPßCD-antisense oligonucleotide formulations showed no sign of physical or chemical degradation over the 1-year stability study, which also shows the suitability of the HPßCD matrix for the formulation of biopharmaceuticals. The obtained results demonstrate possible solutions for the challenges of electrospinning such as scale-up and downstream processing of the fibers.

A protocol to replace dedication to either normal phase or polar organic mode for chiral stationary phases containing amylose tris(3,5-dimethylphenylcarbamate).

Alteration of the enantiorecognition ability of polysaccharide-based chiral columns in the shipping normal phase (NP) eluent after exposition to polar organic (PO) mode eluents can be conceived as an incomplete hysteresis cycle. Non-standard solvents provide a solution to overcome this issue with immobilized stationary phases, but a procedure was missing so far to regenerate coated stationary phases from the altered state. Recent results with alcohol mixtures within the PO mode showed that an appropriate order of standard solvents may also be suitable to complete hysteresis. Using an analogous approach, a simple protocol was established to regenerate the original NP retentions on various stationary phases containing amylose tris(3,5-dimethylphenylcarbamate) (ADMPC) chiral selector after the change induced by flushing with 2-propanol or ethanol. The members of a chemically diverse compound set indicated that alterations in retentions and selectivities using different brands and types of ADMPC-based stationary phases can be quite different, but the recovery of the original state was very good for all of them. The proposed protocol eliminates the need of the costly dedication of a chiral column with ADMPC selector to either NP or PO mode. Furthermore, the limits of the alcohol content in the mobile phase compositions where the system is free of hysteresis were determined.

Utilization of the hysteresis phenomenon for chiral high-performance liquid chromatographic method selection in polar organic mode.

Polysaccharide-based chiral stationary phases (CSPs) are outstandingly suitable to play a key role in chiral HPLC method selection strategies, since they provide high success rates. One reason for this ability is that they adopt a diversity of higher order structures in various eluents, resulting in versatile chiral environments. A potential to extend this versatility further was expected and examined in the present study, based on the recently discovered hysteretic behavior of a widely used chiral selector (CS), amylose tris(3,5-dimethylphenylcarbamate). The hindered transitions of its structure, which are behind the history dependence of its separation ability, were used as a tool to identify distinct states of the chiral selector in order to exploit an extended selectivity space. The identification was carried out using a single diagnostic compound, as opposed to the common approach where testing a library of compounds is required. Eluent mixtures consisting of 2-propanol and either methanol or ethanol were scrutinized in terms of stability and robustness of the observed retentions. The solvent mixtures that were eligible for practical application in these respects were used to construct a screening sequence, including identical compositions combined with different column pretreatment. The gain achievable by using the proposed sequence was then evaluated using 15 enantiomer pairs with focus on resolution, enantiomer elution order and chemoselectivity.

Coupling of large volume injection with flow modulated two-dimensional gas chromatography.

The coupling of large volume injection (LVI) with comprehensive two-dimensional gas chromatography (GC × GC) can be a powerful technique in the analysis of trace-level complex samples. The coupling of LVI and GC × GC using a cost efficiently operable pneumatic modulator based on capillary flow technology has been examined. The aim was to optimize the LVI parameters in the case of samples with compounds covering a wide boiling range. For the optimization of LVI 25 microliters of a solution containing 27 target compounds modelling the composition and the boiling range of diesel oils was used. The injection parameters were evaluated for peak shapes, reproducibility and peak volumes relative to peak volumes obtained using cold splitless injection. For all GC × GC experiments a non-polar first column (Rxi-5ms) and a polar second column (HP-INNOWax) were applied. Through extensive method optimization solvent vent proved to be an unsuitable technique for the injection of compounds covering a wide boiling range: at lower vent times peaks split, while higher vent times caused severe losses of highly volatile compounds. Therefore, a split-splitless LVI method was optimized. Injection speed, split vent time, splitless vent time and vent flow during split vent have been optimized. The developed method is suitable for the coupling of LVI with flow modulated GC × GC. Using the optimized split-splitless LVI parameters no peak distortion of the target compounds was observed. The relative peak volumes were between 60-120% for all compounds (80-120% for 13 compounds).

Determination of polycyclic aromatic hydrocarbons in infant formula using solid state urea clathrate formation with gas chromatography - tandem mass spectrometry.

An analytical method has been developed for the quantitative determination of the 16 EU priority polycyclic aromatic hydrocarbons (PAHs) in infant formula. Prior to analysis infant formula is subjected to sample preparation including the extraction of PAHs from the sample, transesterification of the triglyceride content of the extract to fatty acid methyl esters (FAMEs), and solid state urea clathrate formation to remove the FAMEs. Measurements were carried out with gas chromatography - tandem mass spectrometry. The developed method has been evaluated in terms of trueness, precision (repeatability), limit of detection (LOD), limit of quantification (LOQ), selectivity, sensitivity and linearity. Measurement range of 200-1500ngkg-1 was selected in accordance with the limit values set by the European Commission (835/2011/EC). LOD values were 75ngkg-1 for dibenzo(a,e)pyrene, dibenzo(a,i)pyrene and dibenzo(a,h)pyrene while 50ngkg-1 for the rest of the PAHs (benzo(c)fluorene, benzo(a)anthracene, cyclopenta(cd)pyrene, chrysene, 5-methylchrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(j)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, dibenzo(a,h)anthracene, benzo(g,h,i)perylene, dibenzo(a,l)pyrene), LOQ was 200ngkg-1 for all 16 PAHs. Trueness ranged between -29.7 and 29.8% while precision values were between 0.5 and 24.7% (RSD, n=3).

Identification of uranium signatures relevant for nuclear safeguards and forensics.

The paper describes the applicability of different characteristics (signatures) in nuclear safeguards and forensics for assessment of uranium material provenance in terms of production process. The study follows a uranium ore concentrate production from an ore to a U3O8 product. It turned out that rare-earth elemental pattern, radiochronometry (age of ore body and material production date), sulphur and organic impurities are useful to find out the origin or history of the material, while certain trace-elements and isotopics of Pb or Sr were found to be inconclusive. The results will be important to understand the signatures in nuclear safeguards and forensics.

In vitro and in silico characterization of fibrous scaffolds comprising alternate colistin sulfate-loaded and heat-treated polyvinyl alcohol nanofibrous sheets.

A multilayer mat for dispensing colistin sulfate through a body surface was prepared by electrospinning. The fabricated system comprised various polyvinyl alcohol fibrous layers prepared with or without the active ingredient. One of the electrospun layers contained water-soluble colistin sulfate and the other was prepared from the same polymer type and composition without the active drug and was finally heat-treated. The heat treatment modified the supramolecular structure and conferred the polymer nanofibre with the rate-controlling function. The microstructure of different layers was tracked by positron annihilation lifetime spectroscopy, and detailed morphological analysis of the fibre mats was performed using a scanning electron microscope. The drug-release profiles of various layer arrangements were studied in relation to their antimicrobial activity. The finite element method was applied to overcome the challenge of diffusion-controlled drug release from multilayer polymer scaffolds. The finite element method was first verified using analytical solutions for a simple arrangement (one drug-loaded swellable fibre and one rate-controlling nonswellable fibre) under perfect sink conditions and in a well-stirred finite volume. The effect of alternate layer arrangements on the drug-release profiles was also investigated to plan for controlled topical drug release from fibrous scaffolds. This design is expected to aid in increasing local effectiveness, thus reducing the systemic loading and the consequent side effects of colistin.

Combined cluster and discriminant analysis: An efficient chemometric approach in diesel fuel characterization.

Combined cluster and discriminant analysis (CCDA) as a chemometric tool in compound specific isotope analysis of diesel fuels was studied. The stable carbon isotope ratios (δ13C) of n-alkanes in diesel fuel can be used to characterize or differentiate diesels originating from different sources. We investigated 25 diesel fuel samples representing 20 different brands. The samples were collected from 25 different service stations in 11 European countries over a 2 year period. The n-alkane fraction of diesel fuels was separated using solid-state urea clathrate formation combined with silica gel fractionation. The stable carbon isotope ratios of C10-C24 n-alkanes were measured with gas chromatography-isotope ratio mass spectrometry (GC-IRMS) using perdeuterated n-alkanes as internal standards. Beside the 25 samples one additional diesel fuel was prepared and measured three times to get totally homogenous samples in order to test the performance of our analytical and statistical routine. Stable isotope ratio data were evaluated with hierarchical cluster analysis (HCA), principal component analysis (PCA) and CCDA. CCDA combines two multivariate data analysis methods hierarchical cluster analysis with linear discriminant analysis (LDA). The main idea behind CCDA is to compare the goodness of preconceived (based on the sample origins) and random groupings. In CCDA all the samples were compared pairwise. The results for the parallel sample preparations showed that the analytical procedure does not have any significant effect on the δ13C values of n-alkanes. The three parallels proved to be totally homogenous with CCDA. HCA and PCA can be useful tools when the examining of the relationship among several samples is in question. However, these two techniques cannot be always decisive on the origin of similar samples. The initial hypothesis that all diesel fuel samples are considered chemically unique was verified by CCDA. The main advantage of CCDA is that it gives an objective index number about the level of similarity among the investigated samples. Thus the application of CCDA supplemented by the traditionally used multivariate methods greatly improves the efficiency of statistical analysis in the CSIA of diesel fuel samples.

Determination of particulate phase polycyclic aromatic hydrocarbons and their nitrated and oxygenated derivatives using gas chromatography-mass spectrometry and liquid chromatography-tandem mass spectrometry.

An analytical method has been developed for the quantitative determination of polycyclic aromatic hydrocarbons (PAHs) and their nitrated and oxygenated derivatives (nitro- and oxy-PAHs respectively) in particulate matter (PM) samples. The sample preparation procedure included only a simple and quick sonication-assisted extraction step, clean-up based on addition of water and centrifugation as well as pre-concentration under N2 stream. The determination of 16 PAHs and 4 oxy-PAHs was carried out by gas chromatography-mass spectrometry, while liquid chromatography-tandem mass spectrometry was used in the case of the 11 investigated nitro-PAHs. The optimized method was fully evaluated in terms of trueness, precision (repeatability), limit of detection (LOD), limit of quantification (LOQ), sensitivity and linearity. The LOQ values ranged at pgm-3 level for the investigated PAHs (42pgm-3), oxy-PAHs (either 42 or 83pgm-3) and nitro-PAHs (either 83 or 167pgm-3) as well. The developed method was applied for the quantitative determination of PAHs, nitro- and oxy-PAHs in urban PM2.5 (particles with aerodynamic diameter smaller than 2.5µm) samples (n=36) collected in Budapest, Hungary. Almost 100% of the PM2.5 samples contained the investigated PAHs and oxy-PAHs in detectable and quantifiable amounts; however, the concentration of the nitro-PAHs was generally lower than the corresponding LOD/LOQ values. According to our results, during the 3-year long sampling campaign the concentration of benzo(a)pyrene never exceeded the limit value (1ngm-3) set by the European Commission.

Effects of Temperature and Duration of Storage on the Stability of Antioxidant Compounds in Egg Yolk and Plasma.

Antioxidants help protect tissues from oxidative damage caused by reactive oxygen species. In view of the widespread interest in egg yolk and plasma antioxidants in relation to environmental and life-history variables, there is a need for knowledge on the necessary conditions for sample storage, which is currently lacking. In this study, our purpose was to examine the kinetics of the degradation of lutein, retinol, and tocopherol in egg yolk samples and the total antioxidant capacity in plasma samples stored at three different temperatures (-20°, -50°, and -80°C) for 24 mo. We found that yolk lutein was stable during the study period. Yolk retinol and tocopherol showed a steep early decline and then remained relatively stable, but retinol showed significant losses at the end of the study period too. In contrast to our expectations, there was no difference in the stability of antioxidant compounds of egg yolk samples stored at different temperatures. Plasma OXY level was stable during the first 6 mo, showed a slight decline between 6 and 12 mo, and declined more intensely after 12 mo of storage. We suggest that studies focusing on the analysis of egg yolk retinol or tocopherol concentrations and total plasma antioxidant capacity should analyze the samples in the first 6-7 mo after collection. For the analysis of yolk lutein, samples can be stored for 24 mo without significant degradation. The storage temperature of -20°C seemed to be sufficient, as a lower temperature did not significantly affect the slope of degradation of the samples.

Solubility determination as an alternative to migration measurements.

Solubility values for six UV stabilisers (Cyasorb UV-1164, Tinuvin P, Tinuvin 234, Tinuvin 326, Tinuvin 327 and Tinuvin 1577) and five antioxidants (Irgafos 168, Irganox 1010, Irganox 3114, Irganox 3790 and Irganox 565) were determined in all the liquid food simulants (3% (m/V) acetic acid-water mixture, 10% (V/V), 20% (V/V), 50% (V/V) ethanol-water mixture and vegetable oil) proposed in European Union Regulation No. 10/2011/EC, as well as in fruit juice and cola drink. The applied method was obtained by modification of the method for the determination of water solubility as described in OECD guideline Test No. 105. By using ultrasonication and shorter equilibration time, the time demand of the solubility determinations were decreased notably. Solubility values proved to be lower than the specific migration limits (as specified in 10/2011/EC) at 25 °C for almost all target compounds in food simulants A, B, C and D1 as well as in fruit juice and cola drink. The exceptions were Tinuvin P and Irganox 3790 in simulant D1. The solubility in food simulant D2 was higher than 1000 µg ml(-1) for all target compounds. These results show that the solubility of some additives in food simulants can be so low that it makes migration studies for certain additive-food simulant pairs dispensable.

Effects of breeding habitat (woodland versus urban) and metal pollution on the egg characteristics of great tits (Parus major).

In an urban environment, birds are exposed to metals, which may accumulate in their tissues and cause oxidative stress. Female birds may eliminate these pollutants through depositing them into eggs, thus eggs become suitable bioindicators of pollution. In this study, we aimed to analyse whether eggshell spotting pattern, egg volume, eggshell thickness and egg yolk antioxidant (lutein, tocopherol, retinol and selenium) levels were related to the breeding area (woodland versus urban) and the metal levels in the eggshell of a small passerine species, the great tit (Parus major). In the urban habitat, soil and eggshells contained higher concentrations of metals, and soil calcium level was also higher than that in the woodland. Eggshell spotting intensity and egg volume did not differ between eggs laid in the woodland and the urban park, and these traits were not related to the metal levels of the eggshell, suggesting that these egg characteristics are not sensitive indicators of metal pollution. A more aggregated eggshell spotting distribution indicated a higher Cu concentration of the eggshell. We found that eggshells were thinner in the less polluted woodland habitat, which is likely due to the limited Ca availability of the woodland area. Great tit eggs laid in the urban environment had lower yolk lutein, retinol and selenium concentrations, however, as a possible compensation for these lower antioxidant levels, urban females deposited more tocopherol into the egg yolk. It appears that females from different breeding habitats may provide similar antioxidant protection for their offspring against oxidative damage by depositing different specific dietary antioxidants. Egg yolk lutein and retinol levels showed a negative relationship with lead concentration of the eggshell, which may suggest that lead had a negative impact on the amount of antioxidants available for embryos during development in great tits.

Comparison of spray drying, electroblowing and electrospinning for preparation of Eudragit E and itraconazole solid dispersions.

Three solvent based methods: spray drying (SD), electrospinning (ES) and air-assisted electrospinning (electroblowing; EB) were used to prepare solid dispersions of itraconazole and Eudragit E. Samples with the same API/polymer ratios were prepared in order to make the three technologies comparable. The structure and morphology of solid dispersions were identified by scanning electron microscopy and solid phase analytical methods such as, X-ray powder diffraction (XRPD), differential scanning calorimetry (DSC) and Raman chemical mapping. Moreover, the residual organic solvents of the solid products were determined by static headspace-gas chromatography/mass spectroscopy measurements and the wettability of samples was characterized by contact angle measurement. The pharmaceutical performance of the three dispersion type, evaluated by dissolution tests, proved to be very similar. According to XRPD and DSC analyses, made after the production, all the solid dispersions were free of any API crystal clusters but about 10 wt% drug crystallinity was observed after three months of storage in the case of the SD samples in contrast to the samples produced by ES and EB in which the polymer matrix preserved the API in amorphous state.

Migration of Tinuvin P and Irganox 3114 into milk and the corresponding authorised food simulant.

Migration of Tinuvin P (UV stabiliser) and Irganox 3114 (antioxidant) from high-density polyethylene (HDPE) was studied. HDPE pieces were soaked in either milk (1.5% or 3.5% fat content) or 50% (v/v) ethanol-water mixture - the food simulant for milk as specified in Regulation No. 10/2011/EC. The obtained extracts were analysed by LC-MS/MS. For statistical assessment variography was used. It proved to be a useful tool for making a distinction between the early migration range and the equilibrium, despite the variance of the data. Regulation No. 10/2011/EC specifies 10 days of contact time for milk at 5°C. Our experiments with the food simulant with 24 dm(2) kg(-1) surface/mass ratio showed that both Tinuvin P and Irganox 3114 need less than 1 h to reach equilibrium. Furthermore, 10-day experiments with daily sampling showed that these additives are stable in milk, as well as in the food simulant. The effect of the concentration of the additives in HDPE was studied in the 0.01-5% (m/m) range. For both Tinuvin P and Irganox 3114 and all three extractants the migrated amount became independent of the concentration of the additive in the HDPE approximately at 1% (m/m). For Tinuvin P the food simulant gave a close estimate for the milk samples. However, using the food simulant for modelling the migration of Irganox 3114 into milk gave an overestimation with a factor of minimum 3.5. In the case of Tinuvin P special care must be taken, since the recommended amount in the HDPE can result in additive concentrations near or even over the specific migration limit (SML). However, Irganox 3114 cannot reach the SML either in milk or in the food simulant.

Comparison of directly compressed vitamin B12 tablets prepared from micronized rotary-spun microfibers and cast films.

Fiber-based dosage forms are potential alternatives of conventional dosage forms from the point of the improved extent and rate of drug dissolution. Rotary-spun polymer fibers and cast films were prepared and micronized in order to direct compress after homogenization with tabletting excipients. Particle size distribution of powder mixtures of micronized fibers and films homogenized with tabletting excipients were determined by laser scattering particle size distribution analyzer. Powder rheological behavior of the mixtures containing micronized fibers and cast films was also compared. Positron annihilation lifetime spectroscopy was applied for the microstructural characterization of micronized fibers and films. The water-soluble vitamin B12 release from the compressed tablets was determined. It was confirmed that the rotary spinning method resulted in homogeneous supramolecularly ordered powder mixture, which was successfully compressed after homogenization with conventional tabletting excipients. The obtained directly compressed tablets showed uniform drug release of low variations. The results highlight the novel application of micronized rotary-spun fibers as intermediate for further processing reserving the original favorable powder characteristics of fibrous systems.

Analysis of potential migrants from plastic materials in milk by liquid chromatography-mass spectrometry with liquid-liquid extraction and low-temperature purification.

A simple and fast analytical method was developed for the determination of six UV stabilizers (Cyasorb UV-1164, Tinuvin P, Tinuvin 234, Tinuvin 326, Tinuvin 327, and Tinuvin 1577) and five antioxidants (Irgafos 168, Irganox 1010, Irganox 3114, Irganox 3790, and Irganox 565) in milk. For sample preparation liquid-liquid extraction with low-temperature purification combined with centrifugation was used to remove fats, proteins, and sugars. After the cleanup step, the sample was analyzed with high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS). External standard and matrix calibrations were tested. External calibration proved to be acceptable for Tinuvin P, Tinuvin 234, Tinuvin 326, Tinuvin 327, Irganox 3114, and Irganox 3790. The method was successfully validated with matrix calibration for all compounds. Method detection limits were between 0.25 and 10 µg/kg. Accuracies ranged from 93 to 109%, and intraday precisions were <13%.

Seasonal Monitoring of Cardiovascular and Antiulcer Agents' Concentrations in Stream Waters Encompassing a Capital City.

Nowadays monitoring pharmaceutical residues from surface waters is a widespread analytical task. Most of the studies are conducted from river waters or sewage treatment plants and mainly in Western Europe or North America. Such studies are seldom published from Eastern Europe, especially from stream waters, even though the prescription and consumption patterns of drugs as well as wastewater treatment procedures are very dissimilar. In Hungary the active substance of the most often prescribed drugs are cardiovascular and antiulcer agents. Hence in our study compounds belonging to these two groups were seasonally monitored in two main streams encompassing the Buda side of the Hungarian capital city and flowing into the Danube. To obtain data on the occurrence, fate, and seasonal variation of the compounds, samples were taken from altogether eleven points located near wastewater treatment plants and confluences. The results gave no identifiable pattern in the seasonal variation of concentrations but the contribution of the tributaries and wastewater treatment plants could be followed as expected. From the runoff corrected estuary concentrations the annual contribution of these streams to pharmaceutical pollution of the Danube could be estimated to be in excess of 1 kilogram for atenolol, famotidine, metoprolol, ranitidine, and sotalol.

Development and validation of a liquid chromatographic-tandem mass spectrometric method for determination of eleven coccidiostats in milk.

A reversed phase liquid chromatographic-tandem mass spectrometric method with simple solvent extraction and purification by solid phase extraction (SPE) has been developed for the determination of coccidiostats in milk. For sample preparation matrix solid phase dispersion, extraction by organic solvent and SPE with different cartridges were also tested. The compounds determined include lasalocid, narasin, salinomycin, monensin, semduramicin, maduramicin, robenidine, decoquinate, halofuginone, nicarbazin and diclazuril. Main steps of the method are addition of acetonitrile to the milk samples, centrifugation, removal of matrix by SPE, concentration by evaporation and LC-MS-MS determination. During a 15 min time segmented chromatographic run compounds are ionised either positively or negatively. Calculated recoveries range between 77.1% and 118.2%. Maximum levels are in the range of 1-20 µg/kg. The developed method was validated in line with the requirements of Commission Decision 2002/657/EC (2002). It is applicable for control of coccidiostat residues in milk as indicated in Regulation 124/2009/EC (2009).