RESUMEN
Spinel cobalt ferrite/hexagonal strontium hexaferrite (2CoFe2O4/SrFe12-2xSmxLaxO19; x = 0.2, 0.5, 1.0, 1.5) nanocomposites were fabricated using the tartaric acid precursor pathway, and the effects of La3+-Sm3+ double substitution on the formation, structure, and magnetic properties of CoFe2O4/SrFe12-2xSmxLaxO19 nanocomposite at different annealing temperatures were assayed through X-ray diffraction, scanning electron microscopy, and vibrating sample magnetometry. A pure 2CoFe2O4/SrFe12O19 nanocomposite was obtained from the tartrate precursor complex annealed at 1100 °C for 2 h. The substitution of Fe3+ ion by Sm3-+La3+ions promoted the formation of pure 2CoFe2O4/SrFe12O19 nanocomposite at 1100 °C. The positions and intensities of the strongest peaks of hexagonal ferrite changed after Sm3+-La3+ substitution at ≤1100 °C. In addition, samples with an Sm3+-La3+ ratio of ≥1.0 annealed at 1200 °C for 2 h showed diffraction peaks for lanthanum cobalt oxide (La3Co3O8; dominant phase) and samarium ferrite (SmFeO3). The crystallite size range at all constituent phases was in the nanocrystalline range, from 39.4 nm to 122.4 nm. The average crystallite size of SrFe12O19 phase increased with the number of Sm3+-La3+ substitutions, whereas that of CoFe2O4 phase decreased with an x of up to 0.5. La-Sm co-doped ion substitution increased the saturation magnetization (Ms) value and the subrogated ratio to 0.2, and the Ms value decreased with the increasing number of double substitutions. A high saturation magnetization value (Ms = 69.6 emu/g) was obtained using a La3+-Sm3+ co-doped ratio of 0.2 at 1200 for 2 h, and a high coercive force value (Hc = 1192.0 Oe) was acquired using the same ratio at 1000 °C.
RESUMEN
Al Amar gold ore is rich in sulfides of base metals and is commercially applied for the production of copper concentrate via floatation and gold bullion by cyanidation of tailing. The current process flowsheet suffers from low gold recovery (â¼60%) and loss of metals in the hazardous stockpiled residue. This work addresses these drawbacks by a newly experimental redesign of the process circuit. The innovative flowsheet comprises a sequence of operations, including acid leaching of the roasted ore, gold recovery from the leach residue, and preparation of a valuable zinc-copper-lead ferrite from the filtrate by coprecipitation followed by heat treatment. The ore is roasted at 650 °C and then leached in 20% HCl, where most of Zn, Cu, Pb, and Fe contents are dissolved, while pristine gold remains in the residue. Most of the gold (â¼93%) can be recovered by cyanidation of the acid leach residue. Stoichiometric ratios of dissolved Zn, Cu, Pb, and Fe in the acid leach solution can be kept at 0.6:0.3:0.1:2.0, respectively, only by adding a small amount of ferric chloride. These metals are coprecipitated at varying pH values from 8 to 10, and the produced powders are annealed at temperatures from 600 to 1100 °C. X-ray diffraction (XRD) charts reveal sharp peaks of the targeted Zn0.6Cu0.3Pb0.1Fe2O4 phase at 600 °C, while a highly crystalline single phase is obtained at 1100 °C, independently of precipitation pH. The crystalline size of the produced powders increases with annealing temperatures (from 18-27 nm at 600 °C to 85-105 nm at 1100 °C). The finest size is found at pH 12. Scanning electron microscopy (SEM) investigation shows uniform cubic microstructures of samples annealed at 1100 °C. The produced ferrite powders exhibit soft magnetic characteristics. Saturation magnetization, M s, substantially increases with pH. Coercivity, H c, increases with increasing annealing temperatures, from 600 to 800 °C, and decreases above 800 °C. Preliminary cost-benefit analysis revealed that the profit margin of the proposed process flowsheet is promising. The wastewater is almost free of heavy metals. Our advances in high gold recovery and preparation of valuable magnetic nanocrystalline ferrite provide exciting opportunities to enhance and maximize Al Amar ore production for practical applications.
RESUMEN
The effect of microstructure and chemistry on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys, was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys was also investigated employing dynamic electrochemical impedance spectroscopy (DEIS). Corrosion studies were performed in 0.9% NaCl solution at 37 °C, and the obtained results were compared with ultrapure Ti (99.99%). The different phases of the microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Chemical composition and chemistry of the corroded surfaces were studied using X-ray photoelectron spectroscopy (XPS) analysis. For all studied alloys, the microstructure consisted of α matrix, which was strengthened by ß phase. The highest and the lowest values of the ß phase's volume fraction were recorded for TC21 and Ti-Al-Nb alloys, respectively. The susceptibility of the investigated alloys toward pitting corrosion was enhanced following the sequence: Ti-6Al-7Nb < Ti-6Al-4V << TC21. Ti-6Al-7Nb alloy recorded the lowest pitting corrosion resistance (Rpit) among studied alloys, approaching that of pure Ti. The obvious changes in the microstructure of these alloys, together with XPS findings, were adopted to interpret the pronounced variation in the corrosion behavior of these materials.
RESUMEN
The electrochemical and corrosion (uniform and localized) behavior of a binary Ni52Ti48 shape memory alloy (SMA) and two ternary Ni52Ti48-x Co x (x = 1.5 and 4.0 wt%) SMAs were studied. Measurements were conducted in 0.9% NaCl solution at 37 °C employing various electrochemical methods. These include: linear polarization resistance (LPR), linear sweep voltammetry (LSV), chronoamperometry and dynamic electrochemical impedance spectroscopy (DEIS). Such measurements were complemented with scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analysis. Results revealed that the addition of alloyed Co to NiTi significantly reduced the uniform corrosion rate of the studied SMA and greatly enhanced its pitting corrosion resistance. XPS measurements evidenced high stability of the passive layer and limited adsorption of chloride ions. Additionally, it was found that the passive layer remained primarily composed of titanium oxides. Microstructure changes accompanying the addition of Co were also used to account for its role in improving the corrosion resistance of these materials.