RESUMEN
The primary goal of this study is to develop and analyze 3D printed structures based on a well-known composite known as ß-Tricalcium Phosphate (TCP)- polylactic acid (PLA). There are some interesting aspects of this study. First, we developed 3D printable TCP-PLA composite filaments in-house, with high reproducibility, by a one-step process method using a single screw extruder. Second, we explored the physicochemical properties of the developed TCP-PLA composite filaments. Third, we investigated the effect of an FDM-based nozzle temperature of 190 °C, 200 °C, 210 °C, and 220 °C on the composite's crystallinity and rheological and mechanical properties. Results confirmed the successful development of constant-diameter TCP-PLA composite filaments with a homogeneous distribution of TCP particles in the PLA matrix. We observed that a higher nozzle temperature in the FDM process increased the crystallinity of the printed PLA and TCP-PLA structures. As a result, it also helped to enhance the mechanical properties of the printed structures. The rheological studies were performed in the same temperature range used in the actual FDM process, and results showed an improvement in rheological properties at higher nozzle temperatures. The bare polymer and the composite polymer-ceramic melts exhibited lower viscosity and less rigidity at higher nozzle temperatures, which resulted in enhancing the polymer melt flowability and interlayer bonding between the printed layers. Overall, our results confirmed that 3D printable TCP-PLA filaments could be made in-house, and optimization of the nozzle temperature is essential to developing 3D printed composite parts with favorable mechanical properties.
RESUMEN
This review paper is related to the biomechanics of additively manufactured (AM) metallic scaffolds, in particular titanium alloy Ti6Al4V scaffolds. This is because Ti6Al4V has been identified as an ideal candidate for AM metallic scaffolds. The factors that affect the scaffold technology are the design, the material used to build the scaffold, and the fabrication process. This review paper includes thus a discussion on the design of Ti6A4V scaffolds in relation to how their behavior is affected by their cell shapes and porosities. This is followed by a discussion on the post treatment and mechanical characterization including in-vitro and in-vivo biomechanical studies. A review and discussion are also presented on the ongoing efforts to develop predictive tools to derive the relationships between structure, processing, properties and performance of powder-bed additive manufacturing of metals. This is a challenge when developing process computational models because the problem involves multi-physics and is of multi-scale in nature. Advantages, limitations, and future trends in AM scaffolds are finally discussed. AM is considered at the forefront of Industry 4.0, the fourth industrial revolution. The market of scaffold technology will continue to boom because of the high demand for human tissue repair.
RESUMEN
The ultimate goal of this paper is to develop novel ceramic-polymer-based biocomposite orthopedic scaffolds with the help of additive manufacturing. Specifically, we incorporate a bioceramic known as amorphous magnesium phosphate (AMP) into polylactic acid (PLA) with the help of the melt-blending technique. Magnesium phosphate (MgP) was chosen as the bioactive component as previous studies have confirmed its favorable biomaterial properties, especially in orthopedics. Special care was taken to develop constant diameter AMP-PLA composite filaments, which would serve as feedstock for a fused filament fabrication (FFF)-based three-dimensional (3D) printer. Before the filaments were used for FFF, a thorough set of characterization protocols comprising of phase analysis, microstructure evaluations, thermal analysis, rheological analysis, and in vitro degradation determinations was performed on the biocomposites. Scanning electron microscopy (SEM) results confirmed a homogenous dispersion of AMP particles in the PLA matrix. Rheological studies demonstrated good printability behavior of the AMP-PLA filaments. In vitro degradation studies indicated a faster degradation rate in the case of AMP-PLA filaments as compared to the single phase PLA filaments. Subsequently, the filaments were fed into an FFF setup, and tensile bars and design-specific macroporous AMP-PLA scaffolds were printed. The biocomposite exhibited favorable mechanical properties. Furthermore, in vitro cytocompatibility results revealed higher pre-osteoblast cell attachment and proliferation on AMP-PLA scaffolds as compared to single-phase PLA scaffolds. Altogether, this study provides a proof of concept that design-specific bioactive AMP-PLA biocomposite scaffolds fabricated by FFF can be potential candidates as medical implants in orthopedics.
