Nanoscrolls of Janus Monolayer Transition Metal Dichalcogenides.

Tubular structures of transition metal dichalcogenides (TMDCs) have attracted attention in recent years due to their emergent physical properties, such as the giant bulk photovoltaic effect and chirality-dependent superconductivity. To understand and control these properties, it is highly desirable to develop a sophisticated method to fabricate TMDC tubular structures with smaller diameters and a more uniform crystalline orientation. For this purpose, the rolling up of TMDC monolayers into nanoscrolls is an attractive approach to fabricating such a tubular structure. However, the symmetric atomic arrangement of a monolayer TMDC generally makes its tubular structure energetically unstable due to considerable lattice strain in curved monolayers. Here, we report the fabrication of narrow nanoscrolls by using Janus TMDC monolayers, which have an out-of-plane asymmetric structure. Janus WSSe and MoSSe monolayers were prepared by the plasma-assisted surface atom substitution of WSe2 and MoSe2 monolayers, respectively, and then were rolled by solution treatment. The multilayer tubular structures of Janus nanoscrolls were revealed by scanning transmission electron microscopy observations. Atomic resolution elemental analysis confirmed that the Janus monolayers were rolled up with the Se-side surface on the outside. We found that the present nanoscrolls have the smallest diameter of about 5 nm, which is almost the same as the value predicted by the DFT calculation. The difference in work functions between the S- and Se-side surfaces was measured by Kelvin probe force microscopy, which is in good agreement with the theoretical prediction. Strong interlayer interactions and anisotropic optical responses of the Janus nanoscrolls were also revealed by Raman and photoluminescence spectroscopy.

Remote Excitation of Tip-Enhanced Photoluminescence with a Parallel AgNW Coupler.

Tip-enhanced photoluminescence (TEPL) microscopy allows for the correlation of scanning probe microscopic images and photoluminescent spectra at the nanoscale level in a similar way to tip-enhanced Raman scattering (TERS) microscopy. However, due to the higher cross-section of fluorescence compared to Raman scattering, the diffraction-limited background signal generated by far-field excitation is a limiting factor in the achievable spatial resolution of TEPL. Here, we demonstrate a way to overcome this drawback by using remote excitation TEPL (RE-TEPL). With this approach, the excitation and detection positions are spatially separated, minimizing the far-field contribution. Two probe designs are evaluated, both experimentally and via simulations. The first system consists of gold nanoparticles (AuNPs) through photoinduced deposition on a silver nanowire (AgNW), and the second system consists of two offset parallel AgNWs. This latter coupler system shows a higher coupling efficiency and is used to successfully demonstrate RE-TEPL spectral mapping on a MoSe2/WSe2 lateral heterostructure to reveal spatial heterogeneity at the heterojunction.

High-throughput dry transfer and excitonic properties of twisted bilayers based on CVD-grown transition metal dichalcogenides.

van der Waals (vdW) layered materials have attracted much attention because their physical properties can be controlled by varying the twist angle and layer composition. However, such twisted vdW assemblies are often prepared using mechanically exfoliated monolayer flakes with unintended shapes through a time-consuming search for such materials. Here, we report the rapid and dry fabrication of twisted multilayers using chemical vapor deposition (CVD) grown transition metal chalcogenide (TMDC) monolayers. By improving the adhesion of an acrylic resin stamp to the monolayers, the single crystals of various TMDC monolayers with desired grain size and density on a SiO2/Si substrate can be efficiently picked up. The present dry transfer process demonstrates the one-step fabrication of more than 100 twisted bilayers and the sequential stacking of a twisted 10-layer MoS2 single crystal. Furthermore, we also fabricated hBN-encapsulated TMDC monolayers and various twisted bilayers including MoSe2/MoS2, MoSe2/WSe2, and MoSe2/WS2. The interlayer interaction and quality of dry-transferred, CVD-grown TMDCs were characterized by using photoluminescence (PL), cathodoluminescence (CL) spectroscopy, and cross-sectional electron microscopy. The prominent PL peaks of interlayer excitons can be observed for MoSe2/MoS2 and MoSe2/WSe2 with small twist angles at room temperature. We also found that the optical spectra were locally modulated due to nanosized bubbles, which are formed by the presence of interface carbon impurities. The present findings indicate the widely applicable potential of the present method and enable an efficient search of the emergent optical and electrical properties of TMDC-based vdW heterostructures.

Multilayer In-Plane Heterostructures Based on Transition Metal Dichalcogenides for Advanced Electronics.

In-plane heterostructures of transition metal dichalcogenides (TMDCs) have attracted much attention for high-performance electronic and optoelectronic devices. To date, mainly monolayer-based in-plane heterostructures have been prepared by chemical vapor deposition (CVD), and their optical and electrical properties have been investigated. However, the low dielectric properties of monolayers prevent the generation of high concentrations of thermally excited carriers from doped impurities. To solve this issue, multilayer TMDCs are a promising component for various electronic devices due to the availability of degenerate semiconductors. Here, we report the fabrication and transport properties of multilayer TMDC-based in-plane heterostructures. The multilayer in-plane heterostructures are formed through CVD growth of multilayer MoS2 from the edges of mechanically exfoliated multilayer flakes of WSe2 or NbxMo1-xS2. In addition to the in-plane heterostructures, we also confirmed the vertical growth of MoS2 on the exfoliated flakes. For the WSe2/MoS2 sample, an abrupt composition change is confirmed by cross-sectional high-angle annular dark-field scanning transmission electron microscopy. Electrical transport measurements reveal that a tunneling current flows at the NbxMo1-xS2/MoS2 in-plane heterointerface, and the band alignment is changed from a staggered gap to a broken gap by electrostatic electron doping of MoS2. The formation of a staggered gap band alignment of NbxMo1-xS2/MoS2 is also supported by first-principles calculations.

Vapor-Phase Indium Intercalation in van der Waals Nanofibers of Atomically Thin W6Te6 Wires.

One-dimensional (1D) conducting materials are of great interest as potential building blocks for integrated nanocircuits. Ternary 1D transition-metal chalcogenides, consisting of M6X6 wires with intercalated A atoms (M = Mo or W; X = S, Se, or Te; A = alkali or rare metals, etc.), have attracted much attention due to their 1D metallic behavior, superconductivity, and mechanical flexibility. However, the conventional solid-state reaction usually produces micrometer-scale bulk crystals, limiting their potential use as nanoscale conductors. Here we demonstrate a versatile method to fabricate indium (In)-intercalated W6Te6 (In-W6Te6) bundles with a nanoscale thickness. We first prepared micrometer-long, crystalline bundles of van der Waals W6Te6 wires using chemical vapor deposition and intercalated In into the crystal via a vapor-phase reaction. Atomic-resolution electron microscopy revealed that In atoms were surrounded by three adjacent W6Te6 wires. First-principles calculations suggested that their wire-by-wire stacking can transform through postgrowth intercalation. Individual In-W6Te6 bundles exhibited metallic behavior, as theoretically predicted. We further identified the vibrational modes by combining polarized Raman spectroscopy and nonresonant Raman calculations.

Continuous Color-Tunable Light-Emitting Devices Based on Compositionally Graded Monolayer Transition Metal Dichalcogenide Alloys.

The diverse series of transition metal dichalcogenide (TMDC) materials has been employed in various optoelectronic applications, such as photodetectors, light-emitting diodes, and lasers. Typically, the detection or emission range of optoelectronic devices is unique to the bandgap of the active material. Therefore, to improve the capability of these devices, extensive efforts have been devoted to tune the bandgap, such as gating, strain, and dielectric engineering. However, the controllability of these methods is severely limited (typically ≈0.1 eV). In contrast, alloying TMDCs is an effective approach that yields a composition-dependent bandgap and enables light emissions over a wide range. In this study, a color-tunable light-emitting device using compositionally graded TMDC alloys is fabricated. The monolayer WS2 /WSe2 alloy grown by chemical vapor deposition shows a spatial gradient in the light-emission energy, which varies from 2.1 to 1.7 eV. This alloy is incorporated in an electrolyte-based light-emitting device structure that can tune the recombination zone laterally. Thus, a continuous and reversible color-tunable light-emitting device is successfully fabricated by controlling the light-emitting positions. The results provide a new approach for exploring monolayer semiconductor-based broadband optical applications.

Large-Scale 1T'-Phase Tungsten Disulfide Atomic Layers Grown by Gas-Source Chemical Vapor Deposition.

The control of crystal polymorphism and exploration of metastable, two-dimensional, 1T'-phase, transition-metal dichalcogenides (TMDs) have received considerable research attention. 1T'-phase TMDs are expected to offer various opportunities for the study of basic condensed matter physics and for its use in important applications, such as devices with topological states for quantum computing, low-resistance contact for semiconducting TMDs, energy storage devices, and as hydrogen evolution catalysts. However, due to the high energy difference and phase change barrier between 1T' and the more stable 2H-phase, there are few methods that can be used to obtain monolayer 1T'-phase TMDs. Here, we report on the chemical vapor deposition (CVD) growth of 1T'-phase WS2 atomic layers from gaseous precursors, i.e., H2S and WF6, with alkali metal assistance. The gaseous nature of the precursors, reducing properties of H2S, and presence of Na+, which acts as a countercation, provided an optimal environment for the growth of 1T'-phase WS2, resulting in the formation of high-quality submillimeter-sized crystals. The crystal structure was characterized by atomic-resolution scanning transmission electron microscopy, and the zigzag chain structure of W atoms, which is characteristic of the 1T' structure, was clearly observed. Furthermore, the grown 1T'-phase WS2 showed superconductivity with the transition temperature in the 2.8-3.4 K range and large upper critical field anisotropy. Thus, alkali metal assisted gas-source CVD growth is useful for realizing large-scale, high-quality, phase-engineered TMD atomic layers via a bottom-up synthesis.

Directional Exciton-Energy Transport in a Lateral Heteromonolayer of WSe2-MoSe2.

Controlling the direction of exciton-energy flow in two-dimensional (2D) semiconductors is crucial for developing future high-speed optoelectronic devices using excitons as the information carriers. However, intrinsic exciton diffusion in conventional 2D semiconductors is omnidirectional, and efficient exciton-energy transport in a specific direction is difficult to achieve. Here we demonstrate directional exciton-energy transport across the interface in tungsten diselenide (WSe2)-molybdenum diselenide (MoSe2) lateral heterostructures. Unidirectional transport is spontaneously driven by the built-in asymmetry of the exciton-energy landscape with respect to the heterojunction interface. At excitation positions close to the interface, the exciton photoluminescence (PL) intensity was substantially decreased in the WSe2 region and enhanced in the MoSe2 region. In PL excitation spectroscopy, it was confirmed that the observed phenomenon arises from lateral exciton-energy transport from WSe2 to MoSe2. This directional exciton-energy flow in lateral 2D heterostructures can be exploited in future optoelectronic devices.

Versatile Post-Doping toward Two-Dimensional Semiconductors.

We have developed a simple and straightforward way to realize controlled postdoping toward 2D transition metal dichalcogenides (TMDs). The key idea is to use low-kinetic-energy dopant beams and a high-flux chalcogen beam simultaneously, leading to substitutional doping with controlled dopant densities. Atomic-resolution transmission electron microscopy has revealed that dopant atoms injected toward TMDs are incorporated substitutionally into the hexagonal framework of TMDs. The electronic properties of doped TMDs (Nb-doped WSe2) have shown drastic change and p-type action with more than 2 orders of magnitude increase in current. Position-selective doping has also been demonstrated by the postdoping toward TMDs with a patterned mask on the surface. The postdoping method developed in this work can be a versatile tool for 2D-based next-generation electronics in the future.

Control of Thermal Conductance across Vertically Stacked Two-Dimensional van der Waals Materials via Interfacial Engineering.

A comprehensive understanding of the roles of various nanointerfaces in thermal transport is of critical significance but remains challenging. A two-dimensional van der Waals (vdW) heterostructure with tunable interface lattice mismatch provides an ideal platform to explore the correlation between thermal properties and nanointerfaces and achieve controllable tuning of heat flow. Here, we demonstrate that interfacial engineering is an efficient strategy to tune thermal transport via systematic investigation of the thermal conductance (G) across a series of large-area four-layer stacked vdW materials using an improved polyethylene glycol-assisted time-domain thermoreflectance method. Owing to its rich interfacial mismatch and weak interfacial coupling, the vertically stacked MoSe2-MoS2-MoSe2-MoS2 heterostructure demonstrates the lowest G of 1.5 MW m-2 K-1 among all vdW structures. A roadmap to tune G via homointerfacial mismatch, interfacial coupling, and heterointerfacial mismatch is further demonstrated for thermal tuning. Our work reveals the roles of various interfacial effects on heat flow and highlights the importance of the interfacial mismatch and coupling effects in thermal transport. The design principle is also promising for application in other areas, such as the electrical tuning of energy storage and conversion and the thermoelectricity tuning of thermoelectronics.

Spatial Control of Dynamic p-i-n Junctions in Transition Metal Dichalcogenide Light-Emitting Devices.

Emerging transition metal dichalcogenides (TMDCs) offer an attractive platform for investigating functional light-emitting devices, such as flexible devices, quantum and chiral devices, high-performance optical modulators, and ultralow threshold lasers. In these devices, the key operation is to control the light-emitting position, that is, the spatial position of the recombination zone to generate electroluminescence, which permits precise light guides/passes/confinement to ensure favorable device performance. Although various structures of TMDC light-emitting devices have been demonstrated, including the transistor configuration and heterostructured diodes, it is still difficult to tune the light-emitting position precisely owing to the structural device complexity. In this study, we fabricated two-terminal light-emitting devices with chemically synthesized WSe2, MoSe2, and WS2 monolayers, and performed direct observations of their electroluminescence, from which we discovered a divergence in their light-emitting positions. Subsequently, we propose a method to associate spatial electroluminescence imaging with transport properties among different samples; consequently, a common rule for determining the locations of recombination zones is revealed. Owing to dynamic carrier accumulations and p-i-n junction formations, the light-emitting positions in electrolyte-based devices can be tuned continuously. The proposed method will expand the device applicability for designing functional optoelectronic applications based on TMDCs.

Air-stable and efficient electron doping of monolayer MoS2 by salt-crown ether treatment.

To maximize the potential of transition-metal dichalcogenides (TMDCs) in device applications, the development of a sophisticated technique for stable and highly efficient carrier doping is critical. Here, we report the efficient n-type doping of monolayer MoS2 using KOH/benzo-18-crown-6, resulting in a doped TMDC that is air-stable. MoS2 field-effect transistors show an increase in on-current of three orders of magnitude and degenerate the n-type behaviour with high air-stability for ∼1 month as the dopant concentration increases. Transport measurements indicate a high electron density of 3.4 × 1013 cm-2 and metallic-type temperature dependence for highly doped MoS2. First-principles calculations support electron doping via surface charge transfer from the K/benzo-18-crown-6 complex to monolayer MoS2. Patterned doping is demonstrated to improve the contact resistance in MoS2-based devices.

Wafer-Scale Growth of One-Dimensional Transition-Metal Telluride Nanowires.

The development of bulk synthetic processes to prepare functional nanomaterials is crucial to achieve progress in fundamental and applied science. Transition-metal chalcogenide (TMC) nanowires, which are one-dimensional (1D) structures having three-atom diameters and van der Waals surfaces, have been reported to possess a 1D metallic nature with great potential in electronics and energy devices. However, their mass production remains challenging. Here, a wafer-scale synthesis of highly crystalline transition-metal telluride nanowires is demonstrated by chemical vapor deposition. The present technique enables formation of either aligned, atomically thin two-dimensional (2D) sheets or random networks of three-dimensional (3D) bundles, both composed of individual nanowires. These nanowires exhibit an anisotropic 1D optical response and superior conducting properties. The findings not only shed light on the controlled and large-scale synthesis of conductive thin films but also provide a platform for the study on physics and device applications of nanowire-based 2D and 3D crystals.

Gas-Source CVD Growth of Atomic Layered WS2 from WF6 and H2S Precursors with High Grain Size Uniformity.

Two-dimensional (2D) transition-metal dichalcogenides have attracted a considerable amount of attention because of their potential for post-silicon device applications, as well as for exploring fundamental physics in an ideal 2D system. We tested the chemical vapour deposition (CVD) of WS2 using the gaseous precursors WF6 and H2S, augmented by the Na-assistance method. When Na was present during growth, the process created triangle-shaped WS2 crystals that were 10 µm in size and exhibited semiconducting characteristics. By contrast, the Na-free growth of WS2 resulted in a continuous film with metallic behaviour. These results clearly demonstrate that alkali-metal assistance is valid even in applications of gas-source CVD without oxygen-containing species, where intermediates comprising Na, W, and S can play an important role. We observed that the WS2 crystals grown by gas-source CVD exhibited a narrow size distribution when compared with crystals grown by conventional solid-source CVD, indicating that the crystal nucleation occurred almost simultaneously across the substrate, and that uniform lateral growth was dominant afterwards. This phenomenon was attributed to the suppression of inhomogeneous nucleation through the fast and uniform diffusion of the gas-phase precursors, supported by the Na-assisted suppression of the fast reactions between WF6 and H2S.

Chemically Tuned p- and n-Type WSe2 Monolayers with High Carrier Mobility for Advanced Electronics.

Monolayers of transition metal dichalcogenides (TMDCs) have attracted a great interest for post-silicon electronics and photonics due to their high carrier mobility, tunable bandgap, and atom-thick 2D structure. With the analogy to conventional silicon electronics, establishing a method to convert TMDC to p- and n-type semiconductors is essential for various device applications, such as complementary metal-oxide-semiconductor (CMOS) circuits and photovoltaics. Here, a successful control of the electrical polarity of monolayer WSe2 is demonstrated by chemical doping. Two different molecules, 4-nitrobenzenediazonium tetrafluoroborate and diethylenetriamine, are utilized to convert ambipolar WSe2 field-effect transistors (FETs) to p- and n-type, respectively. Moreover, the chemically doped WSe2 show increased effective carrier mobilities of 82 and 25 cm2 V-1 s-1 for holes and electrons, respectively, which are much higher than those of the pristine WSe2 . The doping effects are studied by photoluminescence, Raman, X-ray photoelectron spectroscopy, and density functional theory. Chemically tuned WSe2 FETs are integrated into CMOS inverters, exhibiting extremely low power consumption (≈0.17 nW). Furthermore, a p-n junction within single WSe2 grain is realized via spatially controlled chemical doping. The chemical doping method for controlling the transport properties of WSe2 will contribute to the development of TMDC-based advanced electronics.

Monolayer MoS2 growth at the Au-SiO2 interface.

Atomically thin transition-metal dichalcogenides (TMDs) are attracting great interest for future electronic applications. Even though much effort has been devoted to preparing large-area, high-quality TMDs over the past few years, the samples are usually grown on substrate surfaces. Here, we demonstrate the direct growth of a MoS2 monolayer at the interface between a Au film and a SiO2 substrate. MoS2 grains were nucleated below Au films deposited on SiO2via interface diffusion and then grown into a continuous MoS2 film. By programming the Au pattern deposited, controlled growth of MoS2 with the desired size and geometry was achieved over preferred locations, facilitating its integration into functional field-effect transistors. Our findings elucidate the fabrication of a two-dimensional semiconductor at the interface of bulk three-dimensional solids, providing a novel means for establishing a clean interface junction. It also offers a promising alternative to the site-selective synthesis of TMDs, which is expected to aid the fabrication of TMD-based nanodevices.

Restoring the intrinsic optical properties of CVD-grown MoS2 monolayers and their heterostructures.

This study investigated the intrinsic optical properties of MoS2 monolayers and MoS2/WS2 van der Waals (vdW) heterostructures, grown using chemical vapor deposition. To understand the effect of the growth substrate, samples grown on a SiO2/Si surface were transferred and suspended onto a porous substrate. This transfer resulted in a blue shift of the excitonic photoluminescence (PL) peak generated by MoS2 monolayers, together with an intensity increase. The blue shift and the intensity increase are attributed to the release of lattice strain and the elimination of substrate-induced non-radiative relaxation, respectively. This suspension technique also allowed the observation of PL resulting from interlayer excitons in the MoS2/WS2 vdW heterostructures. These results indicate that the suppression of lattice strain and non-radiative relaxation is essential for the formation of interlayer excitons, which in turn is crucial for understanding the intrinsic physical properties of vdW heterostructures.

An autopsy case in which self-bloodletting via a cervical blood access led to a fatal outcome.

A 48-year-old woman was found dead on a chair in her living room. She had received dialysis every day because of chronic renal failure for the past 15 years. On a table beside her, there was a mirror and 10-mL syringe on a napkin. A stopper was out of place in a portion of a three-way blood access tube established in the right cervical region, and blood coagulation was noted in the lumen. There was a bloodstained measuring cup on the floor. Autopsy findings included a large number of shunt traces in the bilateral infraclavicular fossae and upper limbs, as well as the cervical blood access terminal reaching the right atrium via the internal jugular vein to superior vena cava. Various organs showed anemia. Neither a fatal lesion nor injury was noted in the main organs. Therefore, this patient may have committed suicide by self-bloodletting via a cervical blood access.

Involvement of extracellular ascorbate and iron in hydroxyl radical generation in rat striatum in carbon monoxide poisoning.

Carbon monoxide (CO) poisoning stimulated generation in rat striatum of toxic hydroxyl radicals (*OH), which might participate in the CO-induced neuronal injury. Since an increase in extracellular ascorbate (AA) stimulated *OH generation in the presence of endogenous metals, including iron, in rat striatum in vivo, we examined the role of extracellular AA in *OH generation due to CO poisoning in the present study. The CO-induced *OH generation in the striatum was strongly suppressed by intrastriatal administration of active, but not inactivated, AA oxidase, which degrades extracellular AA. In addition, CO poisoning caused a significant increase in extracellular AA in rat striatum, suggesting a role of extracellular AA in the CO-induced *OH generation. However, the time-course of changes in extracellular AA could not be completely superimposed on that of the CO-induced *OH generation. On the other hand, the CO-induced *OH generation was completely suppressed by an iron chelator, deferoxamine. These findings suggest that *OH generation in rat striatum due to CO poisoning may involve both extracellular AA and chelatable iron.

Anticancer effects of phenoxazine derivatives revealed by inhibition of cell growth and viability, disregulation of cell cycle, and apoptosis induction in HTLV-1-positive leukemia cells.

Adult T-cell leukemia (ATL) is a malignant tumor of human CD4(+) T cells infected with a human retrovirus, T lymphotropic virus type-1 (HTLV-1). The aim of the present study was to investigate the apoptotic effects of phenoxazines, 2-amino-4,4alpha-dihydro-4alpha,7-dimethyl-3H-phenoxazine-3-one (Phx-1), 3-amino-1,4alpha-dihydro-4alpha,8-dimethyl-2H-phenoxazine-2-one (Phx-2), and 2-aminophenoxazine-3-one (Phx-3) on a T cell leukemia cell line from ATL patients, MT-1 cells; HTLV-1 transformed T-cell lines, HUT-102 cells and MT-2 cells; and an HTLV-1-negative rat sarcoma cell line, XC cells. Among these phenoxazines, Phx-3 at concentrations of less than 10 microg/ml extensively inhibited growth and cell viability; arrested cell cycles at sub G(0)/G(1) phase; and augmented apoptosis of MT-1, HUT-102, and MT-2 cells. However, these phenoxazines did not affect the cell viability of an HTLV-1-negative rat sarcoma cell line, XC cells, and phytohemaggutinin-activated human peripheral blood mononuclear cells, although they markedly inhibited the growth of these cells. The transmission of HTLV-1 from HTLV-1-positive cells (MT-2 cells) to HTLV-1-negative cells (XC cells) was considered to be prevented by Phx-1, Phx-2, or Phx-3 because the syncytium formation between these cells was inhibited markedly in the presence of these phenoxazines. The present results suggest that Phx-1, Phx-2, and, in particular, Phx-3 may be useful as therapeutic agents against ATL, which is extremely refractory to current therapies.