RESUMEN
Magnetoelectric (ME)-based magnetometers have garnered much attention as they boast ultra-low-power systems with a small form factor and limit of detection in the tens of picotesla. The highly sensitive and low-power electric readout from the ME sensor makes them attractive for near DC and low-frequency AC magnetic fields as platforms for continuous magnetic signature monitoring. Among multiple configurations of the current ME magnetic sensors, most rely on exploiting the mechanically resonant characteristics of a released ME microelectromechanical system (MEMS) in a heterostructure device. Through optimizing the resonant device configuration, we design and fabricate a fixed-fixed resonant beam structure with high isolation compared to previous designs operating at ~800 nW of power comprised of piezoelectric aluminum nitride (AlN) and magnetostrictive (Co1-xFex)-based thin films that are less susceptible to vibration while providing similar characteristics to ME-MEMS cantilever devices. In this new design of double-clamped magnetoelectric MEMS resonators, we have also utilized thin films of a new iron-cobalt-hafnium alloy (Fe0.5Co0.5)0.92Hf0.08 that provides a low-stress, high magnetostrictive material with an amorphous crystalline structure and ultra-low magnetocrystalline anisotropy. Together, the improvements of this sensor design yield a magnetic field sensitivity of 125 Hz/mT when released in a compressive state. The overall detection limit of these sensors using an electric field drive and readout are presented, and noise sources are discussed. Based on these results, design parameters for future ME MEMS field sensors are discussed.
RESUMEN
This work describes a 35.9 kHz ultrasonic transducer that incorporates a magnetic arrangement to apply a static-compressive prestress to a d32-mode relaxor ferroelectric single crystal drive-element. The magnetic arrangement produces a 22.5 N static-compressive force, inducing a static compression of â¼630 nm on the drive-element. Operating in air with a continuous-wave 10 V peak drive at â¼35.9 kHz, the measured resonant peak displacement of the transducers head-mass was 127 nm. This is well within the predicted static compression, thus, the drive-element is protected from damaging tensile stress. Under the same drive conditions and at an axial distance of 10 mm from the face of the head-mass, the measured acoustic pressure was â¼12 Pa. Analytical and finite element model predictions and the measured behaviour of a prototype device are presented and show good correlation, demonstrating that magnetic prestressing of the drive-element can be a viable alternative to the traditional bolt-clamp.
RESUMEN
Magnetoelectric materials present a unique opportunity for electric field-controlled magnetism. Even though strain-mediated multiferroic heterostructures have shown unprecedented increase in magnetoelectric coupling compared to single-phase materials, further improvements must be made before ultra-low power memory, logic, magnetic sensors, and wide spectrum antennas can be realized. This work presents how magnetoelectric coupling can be enhanced by simultaneously exploiting multiple strain engineering approaches in heterostructures composed of Fe0.5Co0.5/Ag multilayers on (011) Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 piezoelectric crystals. When grown and measured under strain, these heterostructures exhibit an effective converse magnetoelectric coefficient in the order of 10-5 s m-1: the highest directly measured, non-resonant value to-date. This response occurred at room temperature and at low electric fields (<2 kV cm-1). This large effect is enabled by magnetization reorientation caused by changing the magnetic anisotropy with strain from the substrate and the use of multilayered magnetic materials to minimize the internal stress from deposition. Additionally, the coercive field dependence of the magnetoelectric response under strain suggests contributions from domain-mediated magnetization switching modified by voltage-induced magnetoelastic anisotropy. This work highlights how multicomponent strain engineering enables enhanced magnetoelectric coupling in heterostructures and provides an approach to realize energy-efficient magnetoelectric applications.
RESUMEN
Plastic deformation in ceramic materials is normally only observed in nanometre-sized samples. However, we have observed high levels of plasticity (>50% plastic strain) and excellent elasticity (6% elastic strain) in perovskite oxide Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3, under compression along <100>pc pillars up to 2.1 µm in diameter. The extent of this deformation is much higher than has previously been reported for ceramic materials, and the sample size at which plasticity is observed is almost an order of magnitude larger. Bending tests also revealed over 8% flexural strain. Plastic deformation occurred by slip along {110} <1[Formula: see text]0 > . Calculations indicate that the resulting strain gradients will give rise to giant flexoelectric polarization. First principles models predict that a high concentration of oxygen vacancies weaken the covalent/ionic bonds, giving rise to the unexpected plasticity. Mechanical testing on oxygen vacancies-rich Mn-doped Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 confirmed this prediction. These findings will facilitate the design of plastic ceramic materials and the development of flexoelectric-based nano-electromechanical systems.
RESUMEN
Electrical switching of ferroelectric domains and subsequent domain wall motion promotes strong piezoelectric activity, however, light scatters at refractive index discontinuities such as those found at domain wall boundaries. Thus, simultaneously achieving large piezoelectric effect and high optical transmissivity is generally deemed infeasible. Here, it is demonstrated that the ferroelectric domains in perovskite Pb(In1/2 Nb1/2 )O3 -Pb(Mg1/3 Nb2/3 )O3 -PbTiO3 domain-engineered crystals can be manipulated by electrical field and mechanical stress to reversibly and repeatably, with small hysteresis, transform the opaque polydomain structure into a highly transparent monodomain state. This control of optical properties can be achieved at very low electric fields (less than 1.5 kV cm-1 ) and is accompanied by a large (>10 000 pm V-1 ) piezoelectric coefficient that is superior to linear state-of-the-art materials by a factor of three or more. The coexistence of tunable optical transmissivity and high piezoelectricity paves the way for a new class of photonic devices.
RESUMEN
The advent of caloric materials for magnetocaloric, electrocaloric, and elastocaloric cooling is changing the landscape of solid state cooling technologies with potentials for high-efficiency and environmentally friendly residential and commercial cooling and heat-pumping applications. Given that caloric materials are ferroic materials that undergo first (or second) order phase transitions near room temperature, they open up intriguing possibilities for multiferroic devices with hitherto unexplored functionalities coupling their thermal properties with different fields (magnetic, electric, and stress) through composite configurations. Here we demonstrate a magneto-elastocaloric effect with ultra-low magnetic field (0.16 T) in a compact geometry to generate a cooling temperature change as large as 4 K using a magnetostriction/superelastic alloy composite. Such composite systems can be used to circumvent shortcomings of existing technologies such as the need for high-stress actuation mechanism for elastocaloric materials and the high magnetic field requirement of magnetocaloric materials, while enabling new applications such as compact remote cooling devices.
RESUMEN
The magnetoelastic behavior of multiferroic heterostructures-coupling of magnetic anisotropy or domain dynamics to structural deformations-has been intensively studied for developing materials for energy-efficient, spin-based applications. Here, we report on a large, interface-dominated magnetostriction in (Co/Ni)4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multiferroic heterostructures. Ferromagnetic resonance spectroscopy under voltage-induced strains enabled estimation of the saturation magnetostriction as a function of Ni thickness. The volume and the interface components to the saturation magnetostriction are (6.6 ± 0.9) × 10-6 and (-2.2 ± 0.2) × 10-14 m, respectively. Similar to perpendicular magnetic anisotropy in Co/Ni, the large, negative magnetostriction originates from the Co/Ni interfaces. This interfacial functionality delivers an effect over 300% larger than the bulk contribution and can enable low-energy, nanoelectronic devices that combine the tunable magnetic and magnetostrictive properties of Co/Ni multilayers with the ferroelectric properties of Pb(Mg1/3Nb2/3)O3-PbTiO3.
RESUMEN
The ability to tune both magnetic and electric properties in magnetoelectric (ME) composite heterostructures is crucial for multiple transduction applications including energy harvesting or magnetic field sensing, or other transduction devices. While large ME coupling achieved through interfacial strain-induced rotation of magnetic anisotropy in magnetostrictive/piezoelectric multiferroic heterostructures has been demonstrated, there are presently certain restrictions for achieving a full control of magnetism in an extensive operational dynamic range, limiting practical realization of this effect. Here, we demonstrate the possibility of generating substantial reversible anisotropy changes through induced interfacial strains driven by applied electric fields in magnetostrictive thin films deposited on (0 1 1)-oriented domain-engineered ternary relaxor ferroelectric single crystals with extended temperature and voltage ranges as compared to binary relaxors. We show, through a combination of angular magnetization and magneto-optical domain imaging measurements, that a 90° in-plane rotation of the magnetic anisotropy and propagation of magnetic domains with low applied electric fields under zero electric field bias are realized. To our knowledge, the present value attained for converse magnetoelectric coupling coefficient is the highest achieved in the linear piezoelectric regime and expected to be stable for a wide temperature range, thus representing a step towards practical ME transduction devices.
RESUMEN
A differential structure which has the ability to reject external vibrational noise for Metglas/Pb(Zr,Ti)O(3) (PZT) fiber-based magnetoelectric (ME) heterostructures has been studied. This type of ME structure functions better than conventional sensors as a magnetic sensor when used in an environment in which vibrational isolation is impractical. Sensors fabricated with this differential mode structure can attenuate external vibrational noise by about 10 to 20 dB at different frequencies, while simultaneously having a doubled ME voltage coefficient. Interestingly, in addition to offering a means of mitigating vibrational noise, this ME structure offers the potential to be a hybrid sensor, separating magnetic and acoustical signals.
RESUMEN
A magnetoelectric (ME) bending-mode structure based on Metglas/Pb(Zr,Ti)O(3) fiber laminates has been studied. This bending mode had a fundamental resonance (FBR) of about 210 Hz, which was much lower than that of the longitudinal mode. Near the FBR, the ME voltage coefficient was about 400 V/cm·Oe. Magnetic sensors based on this bending mode had an equivalent magnetic noise floor of ≤ 0.3 pT/âHz at f = 210 Hz.
