RESUMEN
The pharmaceutical industry is in the midst of a transition from traditional batch processes to continuous manufacturing. However, the challenges in making this transition vary depending on the selected manufacturing process. Compared with other oral solid dosage processes, wet granulation has been challenging to move towards continuous processing since traditional equipment has been predominantly strictly batch, instead of readily adapted to material flow such as dry granulation or tablet compression, and there have been few equipment options for continuous granule drying. Recently, pilot and commercial scale equipment combining a twin-screw wet granulator and a novel horizontal vibratory fluid-bed dryer have been developed. This study describes the process space of that equipment and compares the granules produced with batch high-shear and fluid-bed wet granulation processes. The results of this evaluation demonstrate that the equipment works across a range of formulations, effectively granulates and dries, and produces granules of similar or improved quality to batch wet granulation and drying.
RESUMEN
In recent pharmaceutical applications, an active pharmaceutical ingredient (API) can be mixed with a polymer material to yield a composite long-acting drug-delivery device. These devices boast higher patient compliance, localized drug delivery, and lower dosage concentrations, which can increase patient safety. As a laboratory-safe option, calcium carbonate (CaCO3) was used as a drug surrogate to mimic the release kinetics of a low-solubility API. The release of CaCO3 from a poly(ethylene vinyl acetate) (EVA) polymer matrix was studied in ultra-high-purity water. The geometry of CaCO3, along with the manufacturing technique, was manipulated to study the implications on surrogate drug release. It was found that injection molding proved to yield higher burst release, due to higher pressures achievable during manufacturing. The extrusion process can affect the surface concentration of the pharmaceutical ingredient when extruded through a water bath, resulting in a lower initial burst concentration. Regarding CaCO3 geometry, the particle size was more critical than the surface area in terms of CaCO3 release. Larger particles showed a higher release rate, though they also displayed higher variability in release. These data can be used to engineer specific release profiles when designing composite formulations and manufacturing methods for pharmaceutical-drug-delivery applications.
RESUMEN
Taste-masking of drugs, particularly to produce formulations for pediatric patients, can be challenging and require complex manufacturing approaches. The objective of this study was to produce taste-masked ibuprofen granules using a novel process, twin-screw melt granulation (TSMG). TSMG is an emerging, high-productivity, continuous process. Granules of ibuprofen embedded in a lipid matrix were produced across a range of process conditions, resulting in a range of output granule particle sizes. The ibuprofen appeared to be miscible with the lipid binder though it recrystallized after processing. The ibuprofen melt granules were tested in simulated saliva using a novel, small-volume dissolution technique with continuous acquisition of the ibuprofen concentration. The ibuprofen release from the granules was slower than the neat API and physical blend, beyond the expected residence time of the granules in the mouth. The ibuprofen release was inversely related to the granule size. A Noyes-Whitney dissolution model was used and the resulting dissolution rate constants correlated well with the granule size.
RESUMEN
This article highlights the advantages of pharmaceutical continuous melt granulation by twin-screw extrusion. The different melt granulation process options and excipients are described and compared, and a case is made for expanded use of twin-screw melt granulation since it is a flexible and continuous process. Methods for binder selection are profiled with a focus on rheology and physical stability impacts. For twin-screw melt granulation, the mechanism of granulation and process impact on granule properties are described. Pharmaceutical applications of melt granulation ranging from immediate release of soluble and insoluble APIs, taste-masking, and sustained release formulation are reviewed, demonstrating the range of possibilities afforded by twin-screw melt granulation.
RESUMEN
Introduction: Drug eluting implants offer patient convenience and improved compliance through less frequent dosing, eliminating repeated, painful injections and providing localized, site specific delivery with applications in contraception, ophthalmology, and oncology.Areas covered: This review provides an overview of available implant products, design approaches, biodegradable and non-biodegradable polymeric materials, and fabrication techniques with a focus on commercial applications and industrial drug product development. Developing trends in the field, including expanded availability of suitable excipients, development of novel materials, scaled down manufacturing process, and a wider understanding of the implant development process are discussed and point to opportunities for differentiated drug eluting implant products.Expert opinion: In the future, long-acting implants will be important clinical tools for prophylaxis and treatment of global health challenges, especially for infectious diseases, to reduce the cost and difficulty of treating chronic indications, and to prolong local delivery in difficult to administer parts of the body. These products will help improve patient safety, adherence, and comfort.
Asunto(s)
Sistemas de Liberación de Medicamentos , Preparaciones Farmacéuticas , Desarrollo de Medicamentos , Implantes de Medicamentos , Excipientes , HumanosRESUMEN
Medical prescriptions for the alleviation of post-surgical pain are the most abundant source of opioids in circulation. As a systemic drug delivery source, opioids leave patients at high risk for side effects after being dosed. Given the significant rate of unauthorized use, distribution, addiction, and opioid related deaths, an alternative method of post-surgical analgesia is needed. Herein, we report the use of bio-resorbable poly(ester urea) (PEU) films that controllably deliver a non-opioid COX-2 inhibitor, etoricoxib, in vivo and in vitro as a model system for post-surgical pain control. PEU composition, drug-load, and film thickness were varied to selectively control etoricoxib elution. Elution data were fit to a Higuchi model, and the diffusion constant of etoricoxib was calculated in each of the films. Pharmacokinetic (pK) data from an in vivo rat model showed the local tissue concentration of etoricoxib at the study endpoint to be up to 23-fold higher in tissue then plasma. In a well-established mouse model of diabetic neuropathic pain in vivo film implantation showed effective relief of pain for more than 4 days post-implantation and efficacious local etoricoxib delivery. Overall, implementation of local drug delivery systems such as this could reduce the need for opioid prescriptions associated with current pain management strategies.
Asunto(s)
Ésteres , Urea , Animales , Inhibidores de la Ciclooxigenasa 2/uso terapéutico , Preparaciones de Acción Retardada/uso terapéutico , Método Doble Ciego , Ésteres/uso terapéutico , Etoricoxib/uso terapéutico , Humanos , Ratones , Dolor Postoperatorio/tratamiento farmacológico , Piridinas/uso terapéutico , Ratas , Sulfonas/uso terapéuticoRESUMEN
In pharmaceutical development alternative drug delivery modalities are being increasingly employed. One example is an implant, which achieves gradual drug release in patients over a period of many months or years. Due to the complexity of these long-acting formulations, advanced physical characterization methods are desirable as screening tools during protracted formulation development. Imaging methods are of particular interest due to their ability to interrogate the structure and composition of implants spatially across multiple length scales (macro, micro, nano). In this work, spatiochemical imaging is shown to interrogate many crucial drug product attributes of solid implants: overall implant structure, drug distribution, micro-domain size and orientation, agglomeration, porosity and defects, drug/excipient interface, dissolution process, and release mechanism. Imaging methods facilitate a detailed understanding of the process/structure correlation to inform on formulation selection, process parameter optimization, and batch consistency. Numerous case studies of implant applications with imaging are discussed. Methods utilized are X-ray computed tomography (XRCT), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) imaging, and Raman microscopy. The imaging data is complemented with solid-state nuclear magnetic resonance (ssNMR). Altogether, these examples demonstrate that complementary imaging methods are highly effective for analyzing complex and novel pharmaceutical modalities such as solid implants.
Asunto(s)
Preparaciones Farmacéuticas , Liberación de Fármacos , Humanos , Microscopía Electrónica de Rastreo , Prótesis e Implantes , Espectrometría por Rayos XRESUMEN
The emergence of new active pharmaceutical ingredient (API) polymorphs in pharmaceutical development presents significant risks. Even with thorough polymorph screening, new pathways toward alternate crystal phases can present themselves over the course of formulation development; thus, further improvements in phase screening methods are needed. Herein, a case study is presented of a thermodynamically stable crystalline phase of the HIV drug Islatravir (MK-8591, EFdA) that was not isolated from initial pharmaceutical polymorph screening. In total, five Islatravir phases are identified: one monohydrate and four anhydrate phases. The new phase, anhydrate form IV, was unexpectedly discovered during hot melt extrusion (HME) process development of polymeric implant drug product formulations while probing extreme manufacturing process conditions (elevated shear forces). X-ray diffraction (XRD), differential scanning calorimetry (DSC), and solid-state nuclear magnetic resonance (ssNMR) were utilized as principal tools to identify the new polymorph. The result suggests that HME introduces conditions that may allow a thermodynamically stable crystalline phase to form and these conditions are not necessarily captured by routine pharmaceutical polymorph screening. Subsequent investigations identified procedures to generate the new anhydrate phase without HME equipment by the use of special thermal procedures. It is found that for a crystalline hydrate phase the rate of water loss as well as water entrapment in a heating vessel play a crucial role in phase conversions into different anhydrate polymorphs. Further, the polymer involved in the HME manufacturing process also plays a critical role in the phase conversion, likely by coating the API microparticles and thereby altering the phase conversion kinetics. Strategies presented herein to mimic phase changes during formulation manufacture hold promise for the identification of thermodynamically stable anhydrate forms in earlier stages of pharmaceutical development.
Asunto(s)
Desoxiadenosinas/química , Preparaciones Farmacéuticas/química , Rastreo Diferencial de Calorimetría/métodos , Química Farmacéutica/métodos , Composición de Medicamentos/métodos , Desarrollo de Medicamentos/métodos , Tecnología de Extrusión de Fusión en Caliente/métodos , Calor , Polímeros/química , Solubilidad/efectos de los fármacos , Termodinámica , Difracción de Rayos X/métodosRESUMEN
The use of polymers as excipients for drug delivery has afforded stable formulations that reliably control the release of active pharmaceutical ingredients (APIs). While many materials are available and used, few polymers exhibit the numerous advantages, including amorphous characteristics, noninflammatory properties, and resorbable degradation products, like those of poly(ester urea)s (PEUs). Furthermore, stability issues that arise in various APIs can make formulation optimization difficult. Herein, a series of PEUs were synthesized that vary by the fraction of l-phenylalanine monomer incorporated into the copolymerization. The various PEUs and entecavir monohydrate were dry-mixed at different weight percentages (15, 30, and 50%). Filaments of the PEU formulations were extruded and analyzed quantitatively for drug loading and content uniformity by using µ-CT and UPLC analysis. Drug dissolution profiles from filament segments were monitored over a 4-week period and ultimately showed that the controlled release of entecavir was influenced by the incorporation of the l-phenylalanine within the polymer.
Asunto(s)
Aminoácidos/metabolismo , Antivirales/metabolismo , Guanina/análogos & derivados , Poliésteres/metabolismo , Urea/análogos & derivados , Aminoácidos/administración & dosificación , Antivirales/administración & dosificación , Preparaciones de Acción Retardada/administración & dosificación , Preparaciones de Acción Retardada/metabolismo , Guanina/administración & dosificación , Guanina/metabolismo , Poliésteres/administración & dosificación , Urea/administración & dosificación , Urea/metabolismo , Microtomografía por Rayos X/métodosRESUMEN
Alternative formulations of entecavir, a once daily oral hepatitis B antiretroviral, may improve treatment adherence by patients. We explored the use of biocompatible polymers to control entecavir dissolution in two formats suitable for subcutaneous implantation. Hot melt extrudates were prepared by extruding entecavir-polymer blends at specified weight ratios. Dip-coated tablets were prepared by compressing entecavir in a multi-tip tooling. Tablets were dip-coated in solutions of polymer and dried. In rodents, entecavir-poly(caprolactone) extrudates demonstrated >180â¯days of continuous drug release, although below the estimated efficacious target input rate. Drug pharmacokinetic profiles were tunable by varying the polymer employed and implant format. The rank order trends of drug input rates observed in vitro were observed in vivo in the detected plasma concentrations of entecavir. In all dose groups entecavir was not tolerated locally at the site of administration where adverse event severity correlated with drug input rate. These polymer-based implantable formats have applicability to long-acting formulations of high solubility compounds beyond entecavir.
Asunto(s)
Antivirales/química , Antivirales/farmacología , Guanina/análogos & derivados , Hepatitis B/tratamiento farmacológico , Animales , Química Farmacéutica/métodos , Portadores de Fármacos/química , Composición de Medicamentos/métodos , Liberación de Fármacos/efectos de los fármacos , Excipientes/química , Femenino , Guanina/química , Guanina/farmacología , Masculino , Polímeros/química , Ratas , Ratas Wistar , Solubilidad/efectos de los fármacos , Comprimidos/química , Comprimidos/farmacologíaRESUMEN
Localized drug delivery systems (DDSs) provide therapeutic levels of drug agent while mitigating side effects of systemic delivery. These systems offer controlled release over extended periods of time making them attractive therapies. Monitoring drug dissolution is vital for developing safe and effective means of drug delivery. Currently, dissolution characterization methods are limited to bulk analysis and cannot provide dissolution kinetics at high spatial resolution. However, dissolution rates of drug particles can be heterogeneous with influences from many factors. Insights into finer spatiotemporal dynamics of single particle dissolution could potentially improve pharmacokinetic modeling of dissolution for future drug development. In this work, we demonstrate high-resolution chemical mapping of entecavir, a hepatitis B antiviral drug, embedded in a slow release poly(d,l-lactic acid) formulation with stimulated Raman scattering (SRS) microscopy. By tracking the volume change of individual micron-sized drug particles within the polymer matrix, we establish an analytical protocol for quantitatively profiling dissolution of single crystalline particles in implant formulations in an in situ manner.
Asunto(s)
Portadores de Fármacos/química , Implantes de Medicamentos/farmacocinética , Liberación de Fármacos , Guanina/análogos & derivados , Química Farmacéutica/métodos , Implantes de Medicamentos/administración & dosificación , Guanina/administración & dosificación , Guanina/farmacocinética , Microscopía/métodos , Tamaño de la Partícula , Poliésteres/química , Espectrometría Raman/métodosRESUMEN
Regimen adherence remains a major hurdle to the success of daily oral drug regimens for the treatment and prevention of human immunodeficiency virus (HIV) infection. Long-acting drug formulations requiring less-frequent dosing offer an opportunity to improve adherence and allow for more forgiving options with regard to missed doses. The administration of long-acting formulations in a clinical setting enables health care providers to directly track adherence. MK-8591 (4'-ethynyl-2-fluoro-2'-deoxyadenosine [EFdA]) is an investigational nucleoside reverse transcriptase translocation inhibitor (NRTTI) drug candidate under investigation as part of a regimen for HIV treatment, with potential utility as a single agent for preexposure prophylaxis (PrEP). The active triphosphate of MK-8591 (MK-8591-TP) exhibits protracted intracellular persistence and, together with the potency of MK-8591, supports its consideration for extended-duration dosing. Toward this end, drug-eluting implant devices were designed to provide prolonged MK-8591 release in vitro and in vivo Implants, administered subcutaneously, were studied in rodents and nonhuman primates to establish MK-8591 pharmacokinetics and intracellular levels of MK-8591-TP. These data were evaluated against pharmacokinetic and pharmacodynamic models, as well as data generated in phase 1a (Ph1a) and Ph1b clinical studies with once-weekly oral administration of MK-8591. After a single administration in animals, MK-8591 implants achieved clinically relevant drug exposures and sustained drug release, with plasma levels maintained for greater than 6 months that correspond to efficacious MK-8591-TP levels, resulting in a 1.6-log reduction in viral load. Additional studies of MK-8591 implants for HIV treatment and prevention are warranted.