RESUMEN
Alginate hydrogels are widely used as biomaterials for cell culture and tissue engineering due to their biocompatibility and tunable mechanical properties. Reducing alginate molecular weight is an effective strategy for modulating hydrogel viscoelasticity and stress relaxation behavior, which can significantly impact cell spreading and fate. However, current methods like gamma irradiation to produce low molecular weight alginates suffer from high cost and limited accessibility. Here, a facile and cost-effective approach to reduce alginate molecular weight in a highly controlled manner using serial autoclaving is presented. Increasing the number of autoclave cycles results in proportional reductions in intrinsic viscosity, hydrodynamic radius, and molecular weight of the polymer while maintaining its chemical composition. Hydrogels fabricated from mixtures of the autoclaved alginates exhibit tunable mechanical properties, with inclusion of lower molecular weight alginate leading to softer gels with faster stress relaxation behaviors. The method is demonstrated by establishing how viscoelastic relaxation affects the spreading of encapsulated fibroblasts and glioblastoma cells. Results establish repetitive autoclaving as an easily accessible technique to generate alginates with a range of molecular weights and to control the viscoelastic properties of alginate hydrogels, and demonstrate utility across applications in mechanobiology, tissue engineering, and regenerative medicine.
RESUMEN
Silk-amyloid-mussel foot protein (SAM) hydrogels made from recombinant fusion proteins containing ß-amyloid peptide, spider silk domain, and mussel foot protein (Mfp) are attractive bioadhesives as they display a unique combination of tunability, biocompatibility, bioabsorbability, strong cohesion, and underwater adhesion to a wide range of biological surfaces. To design tunable SAM hydrogels for tailored surgical repair applications, an understanding of the relationships between protein sequence and hydrogel properties is imperative. Here, we fabricated SAM hydrogels using fusion proteins of varying lengths of silk-amyloid repeats and Mfps to characterize their structure and properties. We found that increasing silk-amyloid repeats enhanced the hydrogel's ß-sheet content (r = 0.74), leading to higher cohesive strength and toughness. Additionally, increasing the Mfp length beyond the half-length of the full Mfp sequence (1/2 Mfp) decreased the ß-sheet content (r = -0.47), but increased hydrogel surface adhesion. Among different variants, the hydrogel made of 16xKLV-2Mfp displayed a high ultimate strength of 3.0 ± 0.3 MPa, an ultimate strain of 664 ± 119%, and an attractive underwater adhesivity of 416 ± 20 kPa to porcine skin. Collectively, the sequence-structure-property relationships learned from this study will be useful to guide the design of future protein adhesives with tunable characteristics for tailored surgical applications.
RESUMEN
There is a growing demand for the synthesis of high surface area carbons, also known as carbon nanoparticles (CNPs). Existing synthesis methods for high surface area carbons have limited environmental benignity and economic viability due to the requirement of multistep and batch processes and harsh activating and/or templating chemicals. Herein, we demonstrate the synthesis of high surface area CNPs from lignin, a waste byproduct, through a single-step, continuous gas phase aerosol technique without the use of activating or templating chemicals. This continuous approach requires significantly less time for synthesis: on the order of seconds in comparison to hours for conventional methods. Properties of carbon materials synthesized from lignin are controlled by temperature and residence time, and the role of these parameters inside the aerosol reactor on carbon nanoparticle size, morphology, molecular structure, and surface area is systematically investigated. Furthermore, the as-obtained carbon nanoparticles are tested for specific capacitance, and the best-performing material (surface area 925 m2/g) exhibited a specific capacitance of 247 F/g at 0.5 A/g with excellent capacity retainment of over 98% after 10,000 cycles. This is a clear demonstration of their superior performance compared with supercapacitors synthesized earlier from lignin. Overall, the simple (single-step, continuous, and rapid) operation and the avoidance of the use of activating/templating chemicals make the aerosol technique a promising candidate for the scalable and sustainable synthesis of CNPs from lignin.
RESUMEN
Rhodococcus opacus is a bacterium that has a high tolerance to aromatic compounds and can produce significant amounts of triacylglycerol (TAG). Here, we present iGR1773, the first genome-scale model (GSM) of R. opacus PD630 metabolism based on its genomic sequence and associated data. The model includes 1773 genes, 3025 reactions, and 1956 metabolites, was developed in a reproducible manner using CarveMe, and was evaluated through Metabolic Model tests (MEMOTE). We combine the model with two Constraint-Based Reconstruction and Analysis (COBRA) methods that use transcriptomics data to predict growth rates and fluxes: E-Flux2 and SPOT (Simplified Pearson Correlation with Transcriptomic data). Growth rates are best predicted by E-Flux2. Flux profiles are more accurately predicted by E-Flux2 than flux balance analysis (FBA) and parsimonious FBA (pFBA), when compared to 44 central carbon fluxes measured by 13C-Metabolic Flux Analysis (13C-MFA). Under glucose-fed conditions, E-Flux2 presents an R2 value of 0.54, while predictions based on pFBA had an inferior R2 of 0.28. We attribute this improved performance to the extra activity information provided by the transcriptomics data. For phenol-fed metabolism, in which the substrate first enters the TCA cycle, E-Flux2's flux predictions display a high R2 of 0.96 while pFBA showed an R2 of 0.93. We also show that glucose metabolism and phenol metabolism function with similar relative ATP maintenance costs. These findings demonstrate that iGR1773 can help the metabolic engineering community predict aromatic substrate utilization patterns and perform computational strain design.
Asunto(s)
Ingeniería Metabólica , Rhodococcus , Ingeniería Metabólica/métodos , Análisis de Flujos Metabólicos/métodos , Rhodococcus/genética , Rhodococcus/metabolismo , Fenoles/metabolismoRESUMEN
Spatial heterogeneity in composition and organisation of the primary cell wall affects the mechanics of cellular morphogenesis. However, directly correlating cell wall composition, organisation and mechanics has been challenging. To overcome this barrier, we applied atomic force microscopy coupled with infrared (AFM-IR) spectroscopy to generate spatially correlated maps of chemical and mechanical properties for paraformaldehyde-fixed, intact Arabidopsis thaliana epidermal cell walls. AFM-IR spectra were deconvoluted by non-negative matrix factorisation (NMF) into a linear combination of IR spectral factors representing sets of chemical groups comprising different cell wall components. This approach enables quantification of chemical composition from IR spectral signatures and visualisation of chemical heterogeneity at nanometer resolution. Cross-correlation analysis of the spatial distribution of NMFs and mechanical properties suggests that the carbohydrate composition of cell wall junctions correlates with increased local stiffness. Together, our work establishes new methodology to use AFM-IR for the mechanochemical analysis of intact plant primary cell walls.
RESUMEN
Many valorization approaches for lignin rely on its organic solvent (organosolv) extraction. However, the severity of the extraction conditions required to obtain high lignin extraction generally results in low-quality lignin for downstream processing. To better understand the secondary reaction pathways and kinetics related to molecular alterations that result from organosolv extraction under extreme conditions, extractions were conducted at temperatures of 150, 180, and 210 °C. Lignin was collected at residence times between 0.25 and 18â h and analyzed by NMR techniques to quantify the concentrations of key chemical moieties that appear or disappear upon reactions of lignin molecules during and after their fractionation from biomass. The kinetics of chemical moiety evolution was modeled as processes in-series. In these models, pseudo first-order kinetics were used to describe the change in concentration of chemical moieties on extracted lignin as a function of residence time.
RESUMEN
The cell walls of the genus Rhodococcus including the pathogenic bacterium Rhodococcus equi (R. equi) and biotechnologically important bacterium Rhodococcus opacus (R. opacus) contain an abundant peptidolipid (or termed lipopeptide) family whose structures have not been reported previously. Here, we describe a linear ion-trap multiple-stage mass spectrometric (LIT MSn) approach with high resolution mass spectrometry (HRMS), in conjunction with NMR spectroscopy, chemical reactions, and GC/MS analysis to define the structures of these compounds. We employed LIT MSn (n = 2-8) on the [M + Na]+ ion species to establish the peptide sequence, the identity of the fatty acyl substituent, and its location within the molecule, while NMR spectroscopy and GC/MS were used to recognize the Leu and Ile moieties. The major new lipopeptide found in R. opacus is defined as C17H35CH(OH)CH2CO-NHLeu-Ser-Leu-Ile-Thr-Ile-PheCOOH, where a ß-OH fatty acyl (C18-C22) substituent is attached to the N-terminal of the LSLITIF peptide chain via a NH-CO bond. By contrast, the main peptidolipids found in R. equi belong to the cyclopeptidolipid family, which possesses the same peptide sequence and lipid chain, but the ß-OH group of the fatty acyl moiety and the C-terminus of the peptide (i.e., the -COOH) are cyclized by an ester bond formation to a lactone, with a structure similar to iturin-A (Peypoux, F. et al. Biochemistry 1978, 17, 3992-3996). The antibiotic activity test of these new lipids did not reveal an activity against any of seven microorganisms tested.
Asunto(s)
Lipopéptidos/química , Rhodococcus equi/química , Rhodococcus/química , Infecciones por Actinomycetales/microbiología , Secuencia de Aminoácidos , Aminoácidos/análisis , Antibacterianos/química , Cromatografía Líquida de Alta Presión , Ácidos Grasos/análisis , Cromatografía de Gases y Espectrometría de Masas , Espectroscopía de Resonancia MagnéticaRESUMEN
The current extraction and use of fossil fuels has been linked to extensive negative health and environmental outcomes. Lignocellulosic biomass-derived biofuels and bioproducts are being actively considered as renewable alternatives to the fuels, chemicals, and materials produced from fossil fuels. A major challenge limiting large-scale, economic deployment of second-generation biorefineries is the insufficient product yield, diversity, and value that current conversion technologies can extract from lignocellulose, in particular from the underutilized lignin fraction. Rhodococcus opacus PD630 is an oleaginous gram-positive bacterium with innate catabolic pathways and tolerance mechanisms for the inhibitory aromatic compounds found in depolymerized lignin, as well as native or engineered pathways for hexose and pentose sugars found in the carbohydrate fractions of biomass. As a result, R. opacus holds potential as a biological chassis for the conversion of lignocellulosic biomass into biodiesel precursors and other value-added products. This review begins by examining the important role that lignin utilization will play in the future of biorefineries and by providing a concise survey of the current lignin conversion technologies. The genetic machinery and capabilities of R. opacus that allow the bacterium to tolerate and metabolize aromatic compounds and depolymerized lignin are also discussed, along with a synopsis of the genetic toolbox and synthetic biology methods now available for engineering this organism. Finally, we summarize the different feedstocks that R. opacus has been demonstrated to consume, and the high-value products that it has been shown to produce. Engineered R. opacus will enable lignin valorization over the coming years, leading to cost-effective conversion of lignocellulose into fuels, chemicals, and materials.
RESUMEN
Rhodococcus opacus PD630 metabolizes aromatic substrates and naturally produces branched-chain lipids, which are advantageous traits for lignin valorization. To provide insights into its lignocellulose hydrolysate utilization, we performed 13C-pathway tracing, 13C-pulse-tracing, transcriptional profiling, biomass composition analysis, and metabolite profiling in conjunction with 13C-metabolic flux analysis (13C-MFA) of phenol metabolism. We found that 1) phenol is metabolized mainly through the ortho-cleavage pathway; 2) phenol utilization requires a highly active TCA cycle; 3) NADPH is generated mainly via NADPH-dependent isocitrate dehydrogenase; 4) active cataplerotic fluxes increase plasticity in the TCA cycle; and 5) gluconeogenesis occurs partially through the reversed Entner-Doudoroff pathway (EDP). We also found that phenol-fed R. opacus PD630 generally has lower sugar phosphate concentrations (e.g., fructose 1,6-bisphosphatase) compared to metabolite pools in 13C-glucose-fed Escherichia coli (set as internal standards), while its TCA metabolites (e.g., malate, succinate, and α-ketoglutarate) accumulate intracellularly with measurable succinate secretion. In addition, we found that phenol utilization was inhibited by benzoate, while catabolite repressions by other tested carbon substrates (e.g., glucose and acetate) were absent in R. opacus PD630. Three adaptively-evolved strains display very different growth rates when fed with phenol as a sole carbon source, but they maintain a conserved flux network. These findings improve our understanding of R. opacus' metabolism for future lignin valorization.
Asunto(s)
Proteínas Bacterianas , Evolución Molecular Dirigida , Redes y Vías Metabólicas , Fenol/metabolismo , Rhodococcus , Proteínas Bacterianas/genética , Proteínas Bacterianas/metabolismo , Escherichia coli/genética , Escherichia coli/metabolismo , Rhodococcus/genética , Rhodococcus/metabolismo , Biología de SistemasRESUMEN
Spinal cord injury can lead to severe dysfunction as a result of limited nerve regeneration that is due to an inhibitory environment created at the site of injury. Neural tissue engineering using materials that closely mimic the extracellular matrix (ECM) during neural development could enhance neural regeneration. Glycosaminoglycans (GAGs), which are sulfated polysaccharides, have been shown to modulate axonal outgrowth in neural tissue depending upon the position and degree of sulfation. Cellulose sulfate (CelS), which is a GAG mimetic, was evaluated for its use in promoting neurite extension. Aligned fibrous scaffolds containing gelatin blended with 0.25% partially sulfated cellulose sulfate (pCelS), having sulfate predominantly at the 6-carbon position of the glucose monomer unit, and fully sulfated cellulose sulfate (fCelS), which is sulfated at the 2-, 3-, and 6-carbon positions of the glucose monomer unit, were fabricated using the electrospinning method. Comparisons were made with scaffolds containing native GAGs, chondroitin sulfate-A (CS-A) and chondroitin sulfate-C (CS-C), which were obtained from commercial sources. CS-A and CS-C are present in neural tissue ECM. The degree of sulfation and position of sulfate groups was determined using elemental analysis, Fourier-transform infrared spectroscopy (FTIR), Raman microspectroscopy, and 13C nuclear magnetic resonance (NMR). In vitro studies examined both nerve growth factor (NGF) binding on scaffolds and neurite extension by dorsal root ganglion (DRG) neurons. NGF binding was highest on scaffolds containing pCelS and fCelS. Neurite extension was greatest for scaffolds containing fCelS followed by pCelS, with the lowest outgrowth on the CS-A containing scaffolds, suggesting that the degree and position of sulfation of CelS was permissible for neurite outgrowth. This study demonstrated that cellulose sulfate, as a GAG mimetic, could be used for future neural tissue regeneration application. STATEMENT OF SIGNFICANCE: Scaffolds that closely mimic the native extracellular matrix (ECM) during development may be a promising approach to enhance neural regeneration. Here, we reported a glycosaminoglycan (GAG) mimetic derived from cellulose that promotes neurite extension over native GAGs, chondroitin sulfate-A (CS-A) and chondroitin sulfate-C (CS-C), which are present in neural ECM. Depending upon the degree and position of sulfation, the GAG mimetic can impact nerve growth factor binding and permissive neurite outgrowth.
Asunto(s)
Materiales Biomiméticos , Celulosa/análogos & derivados , Sulfatos de Condroitina , Neuritas/metabolismo , Neurogénesis/efectos de los fármacos , Andamios del Tejido/química , Animales , Materiales Biomiméticos/química , Materiales Biomiméticos/farmacología , Celulosa/química , Celulosa/farmacología , Sulfatos de Condroitina/química , Sulfatos de Condroitina/farmacología , Ratas , Ratas Sprague-DawleyRESUMEN
MAIN CONCLUSION: Common duckweed Lemna minor was cultivated in 50% D2O to produce biomass with 50-60% deuterium incorporation containing cellulose with degree of polymerization close (85%) to that of H2O-grown controls. The small aquatic plant duckweed, particularly the genus Lemna, widely used for toxicity testing, has been proposed as a potential source of biomass for conversion into biofuels as well as a platform for production of pharmaceuticals and specialty chemicals. Ability to produce deuterium-substituted duckweed can potentially extend the range of useful products as well as assist process improvement. Cultivation of these plants under deuterating conditions was previously been reported to require addition of kinetin to induce growth and was hampered by anomalies in cellular morphology and protein metabolism. Here, we report the production of biomass with 50-60% deuterium incorporation by long-term photoheterotrophic growth of common duckweed Lemna minor in 50% D2O with 0.5% glucose. L. minor grown in 50% D2O without addition of kinetin exhibited a lag phase twice that of H2O-grown controls, before start of log phase growth at 40% of control rates. Compared to continuous white fluorescent light, growth rates increased fivefold for H2O and twofold for 50% D2O when plants were illuminated at higher intensity with a metal halide lamp and a diurnal cycle of 12-h light/12-h dark. Deuterium incorporation was determined by a combination of 1H and 2H nuclear magnetic resonance (NMR) to be 40-60%. The cellulose from the deuterated plants had an average-number degree of polymerization (DPn) and polydispersity index (PDI) close to that of H2O-grown controls, while Klason lignin content was reduced. The only major gross morphological change noted was root inhibition.
Asunto(s)
Araceae/metabolismo , Biomasa , Deuterio/metabolismo , Celulosa/metabolismo , Espectroscopía de Resonancia MagnéticaRESUMEN
Lignin utilization has been identified as a key factor in biorefinery profitability. However, lignin depolymerization generates heterogeneous aromatic mixtures that inhibit microbial growth and the conversion of lignocellulose to biochemicals. Rhodococcus opacus is a promising aromatic-catabolizing, oleaginous bacterium, but mechanisms for its aromatic tolerance and utilization remain undercharacterized. To better understand these mechanisms, we adaptively evolved R. opacus for improved utilization of 32 combinations of diverse aromatic compounds. Evolved R. opacus mutants showed up to 1900% growth improvement in the utilization of phenol, guaiacol, 4-hydroxybenzoate, vanillate, and benzoate compared to the wild-type strain. Whole genome sequencing revealed several redox-related genes with mutations shared across multiple adapted mutants. PVHG6, the mutant with the most improved growth on a mixture of multiple aromatic compounds, showed 56% lower superoxide dismutase activity than the wild-type strain, suggesting that redox reactions are important for aromatic tolerance and utilization. Comparative transcriptomics revealed by-product detoxification pathways and five aromatic funneling pathways that were upregulated in response to specific aromatic compounds. Gene knockout experiments confirmed the two degradation routes of the ß-ketoadipate pathway for five aromatic compounds. These results provide an improved understanding of aromatic bioconversion and facilitate development of R. opacus as a biorefinery host.
Asunto(s)
Proteínas Bacterianas , Evolución Molecular Dirigida , Genómica , Hidrocarburos Aromáticos/metabolismo , Rhodococcus , Proteínas Bacterianas/biosíntesis , Proteínas Bacterianas/genética , Rhodococcus/genética , Rhodococcus/metabolismoRESUMEN
BACKGROUND: Lignin is a recalcitrant aromatic polymer that is a potential feedstock for renewable fuel and chemical production. Rhodococcus opacus PD630 is a promising strain for the biological upgrading of lignin due to its ability to tolerate and utilize lignin-derived aromatic compounds. To enhance its aromatic tolerance, we recently applied adaptive evolution using phenol as a sole carbon source and characterized a phenol-adapted R. opacus strain (evol40) and the wild-type (WT) strain by whole genome and RNA sequencing. While this effort increased our understanding of the aromatic tolerance, the tolerance mechanisms were not completely elucidated. RESULTS: We hypothesize that the composition of lipids plays an important role in phenol tolerance. To test this hypothesis, we applied high-resolution mass spectrometry analysis to lipid samples obtained from the WT and evol40 strains grown in 1 g/L glucose (glucose), 0.75 g/L phenol (low phenol), or 1.5 g/L phenol (high phenol, evol40 only) as a sole carbon source. This analysis identified > 100 lipid species of mycolic acids, phosphatidylethanolamines (PEs), phosphatidylinositols (PIs), and triacylglycerols. In both strains, mycolic acids had fewer double bond numbers in phenol conditions than the glucose condition, and evol40 had significantly shorter mycolic acid chain lengths than the WT strain in phenol conditions. These results indicate that phenol adaptation affected mycolic acid membrane composition. In addition, the percentage of unsaturated phospholipids decreased for both strains in phenol conditions compared to the glucose condition. Moreover, the PI content increased for both strains in the low phenol condition compared to the glucose condition, and the PI content increased further for evol40 in the high phenol condition relative to the low phenol condition. CONCLUSIONS: This work represents the first comprehensive lipidomic study on the membrane of R. opacus grown using phenol as a sole carbon source. Our results suggest that the alteration of the mycolic acid and phospholipid membrane composition may be a strategy of R. opacus for phenol tolerance.
RESUMEN
Lignin-derived (e.g. phenolic) compounds can compromise the bioconversion of lignocellulosic biomass to fuels and chemicals due to their toxicity and recalcitrance. The lipid-accumulating bacterium Rhodococcus opacus PD630 has recently emerged as a promising microbial host for lignocellulose conversion to value-added products due to its natural ability to tolerate and utilize phenolics. To gain a better understanding of its phenolic tolerance and utilization mechanisms, we adaptively evolved R. opacus over 40 passages using phenol as its sole carbon source (up to 373% growth improvement over wild-type), and extensively characterized two strains from passages 33 and 40. The two adapted strains showed higher phenol consumption rates (â¼20 mg/l/h) and â¼2-fold higher lipid production from phenol than the wild-type strain. Whole-genome sequencing and comparative transcriptomics identified highly-upregulated degradation pathways and putative transporters for phenol in both adapted strains, highlighting the important linkage between mechanisms of regulated phenol uptake, utilization, and evolved tolerance. Our study shows that the R. opacus mutants are likely to use their transporters to import phenol rather than export them, suggesting a new aromatic tolerance mechanism. The identified tolerance genes and pathways are promising candidates for future metabolic engineering in R. opacus for improved lignin conversion to lipid-based products.
Asunto(s)
Adaptación Fisiológica/genética , Proteínas Bacterianas/genética , Proteínas Portadoras/genética , Regulación Bacteriana de la Expresión Génica , Fenoles/metabolismo , Rhodococcus/genética , Proteínas Bacterianas/metabolismo , Biotransformación , Carbono/metabolismo , Proteínas Portadoras/metabolismo , Ontología de Genes , Secuenciación de Nucleótidos de Alto Rendimiento , Lipogénesis/genética , Anotación de Secuencia Molecular , Rhodococcus/metabolismo , TranscriptomaRESUMEN
BACKGROUND: Woody biomass is highly recalcitrant to enzymatic sugar release and often requires significant size reduction and severe pretreatments to achieve economically viable sugar yields in biological production of sustainable fuels and chemicals. However, because mechanical size reduction of woody biomass can consume significant amounts of energy, it is desirable to minimize size reduction and instead pretreat larger wood chips prior to biological conversion. To date, however, most laboratory research has been performed on materials that are significantly smaller than applicable in a commercial setting. As a result, there is a limited understanding of the effects that larger biomass particle size has on the effectiveness of steam explosion pretreatment and subsequent enzymatic hydrolysis of wood chips. RESULTS: To address these concerns, novel downscaled analysis and high throughput pretreatment and hydrolysis (HTPH) were applied to examine whether differences exist in the composition and digestibility within a single pretreated wood chip due to heterogeneous pretreatment across its thickness. Heat transfer modeling, Simons' stain testing, magnetic resonance imaging (MRI), and scanning electron microscopy (SEM) were applied to probe the effects of pretreatment within and between pretreated wood samples to shed light on potential causes of variation, pointing to enzyme accessibility (i.e., pore size) distribution being a key factor dictating enzyme digestibility in these samples. Application of these techniques demonstrated that the effectiveness of pretreatment of Populus tremuloides can vary substantially over the chip thickness at short pretreatment times, resulting in spatial digestibility effects and overall lower sugar yields in subsequent enzymatic hydrolysis. CONCLUSIONS: These results indicate that rapid decompression pretreatments (e.g., steam explosion) that specifically alter accessibility at lower temperature conditions are well suited for larger wood chips due to the non-uniformity in temperature and digestibility profiles that can result from high temperature and short pretreatment times. Furthermore, this study also demonstrated that wood chips were hydrated primarily through the natural pore structure during pretreatment, suggesting that preserving the natural grain and transport systems in wood during storage and chipping processes could likely promote pretreatment efficacy and uniformity.
RESUMEN
This study presents high temperature water-only continuous flowthrough pretreatment coupled with nuclear magnetic resonance (NMR) as a promising analytical tool to examine the plant cell wall, to understand its recalcitrance (i.e., cell wall resistance to deconstruction), and to probe the chemistry occurring during batch pretreatment of biomass. (13)C-enriched corn stover stems were pretreated at 170°C for 60min with a hot-water flow rate of 20mL/min to control fractionation of the cell wall. This approach helped elucidate the nature of plant cell wall chemical recalcitrance and biomass pretreatment chemistry by tracking cell wall fragmentation as a function of time. Fractions of the reactor effluent were collected in a time-resolved fashion and characterized by various NMR techniques to determine the degree and sequence of fragments released, as well as, the chemical composition, molecular structure, and relative molecular weight of those released fragments.
Asunto(s)
Biomasa , Isótopos de Carbono/química , Celulosa/química , Tallos de la Planta/química , Zea mays/química , Espectroscopía de Resonancia Magnética , AguaRESUMEN
MAIN CONCLUSION: The bioenergy crop switchgrass was grown hydroponically from tiller cuttings in 50 % D 2 O to obtain biomass with 34 % deuterium substitution and physicochemical properties similar to those of H 2 O-grown switchgrass controls. Deuterium enrichment of biological materials can potentially enable expanded experimental use of small angle neutron scattering (SANS) to investigate molecular structural transitions of complex systems such as plant cell walls. Two key advances have been made that facilitate cultivation of switchgrass, an important forage and biofuel crop, for controlled isotopic enrichment: (1) perfusion system with individual chambers and (2) hydroponic growth from tiller cuttings. Plants were grown and maintained for several months with periodic harvest. Photosynthetic activity was monitored by measurement of CO2 in outflow from the growth chambers. Plant morphology and composition appeared normal compared to matched controls grown with H2O. Using this improved method, gram quantities of switchgrass leaves and stems were produced by continuous hydroponic cultivation using growth medium consisting of basal mineral salts in 50 % D2O. Deuterium incorporation was confirmed by detection of the O-D and C-D stretching peaks with FTIR and quantified by (1)H- and (2)H-NMR. This capability to produce deuterated lignocellulosic biomass under controlled conditions will enhance investigation of cell wall structure and its deconstruction by neutron scattering and NMR techniques.
Asunto(s)
Deuterio/metabolismo , Hidroponía/métodos , Panicum/crecimiento & desarrollo , Panicum/metabolismo , Biomasa , Celulosa/aislamiento & purificación , Cristalización , Peso Molecular , Perfusión , Hojas de la Planta/anatomía & histología , Polisacáridos/aislamiento & purificación , Espectroscopía Infrarroja por Transformada de FourierRESUMEN
BACKGROUND: Obtaining a better understanding of the complex mechanisms occurring during lignocellulosic deconstruction is critical to the continued growth of renewable biofuel production. A key step in bioethanol production is thermochemical pretreatment to reduce plant cell wall recalcitrance for downstream processes. Previous studies of dilute acid pretreatment (DAP) have shown significant changes in cellulose ultrastructure that occur during pretreatment, but there is still a substantial knowledge gap with respect to the influence of lignin on these cellulose ultrastructural changes. This study was designed to assess how the presence of lignin influences DAP-induced changes in cellulose ultrastructure, which might ultimately have large implications with respect to enzymatic deconstruction efforts. RESULTS: Native, untreated hybrid poplar (Populus trichocarpa x Populus deltoids) samples and a partially delignified poplar sample (facilitated by acidic sodium chlorite pulping) were separately pretreated with dilute sulfuric acid (0.10 M) at 160°C for 15 minutes and 35 minutes, respectively . Following extensive characterization, the partially delignified biomass displayed more significant changes in cellulose ultrastructure following DAP than the native untreated biomass. With respect to the native untreated poplar, delignified poplar after DAP (in which approximately 40% lignin removal occurred) experienced: increased cellulose accessibility indicated by increased Simons' stain (orange dye) adsorption from 21.8 to 72.5 mg/g, decreased cellulose weight-average degree of polymerization (DPw) from 3087 to 294 units, and increased cellulose crystallite size from 2.9 to 4.2 nm. These changes following DAP ultimately increased enzymatic sugar yield from 10 to 80%. CONCLUSIONS: Overall, the results indicate a strong influence of lignin content on cellulose ultrastructural changes occurring during DAP. With the reduction of lignin content during DAP, the enlargement of cellulose microfibril dimensions and crystallite size becomes more apparent. Further, this enlargement of cellulose microfibril dimensions is attributed to specific processes, including the co-crystallization of crystalline cellulose driven by irreversible inter-chain hydrogen bonding (similar to hornification) and/or cellulose annealing that converts amorphous cellulose to paracrystalline and crystalline cellulose. Essentially, lignin acts as a barrier to prevent cellulose crystallinity increase and cellulose fibril coalescence during DAP.
RESUMEN
BACKGROUND: Agave, which is well known for tequila and other liquor production in Mexico, has recently gained attention because of its attractive potential to launch sustainable bioenergy feedstock solutions for semi-arid and arid lands. It was previously found that agave cell walls contain low lignin and relatively diverse non-cellulosic polysaccharides, suggesting unique recalcitrant features when compared to conventional C4 and C3 plants. RESULTS: Here, we report sugar release data from fungal enzymatic hydrolysis of non-pretreated and hydrothermally pretreated biomass that shows agave to be much less recalcitrant to deconstruction than poplar or switchgrass. In fact, non-pretreated agave has a sugar release five to eight times greater than that of poplar wood and switchgrass . Meanwhile, state of the art techniques including glycome profiling, nuclear magnetic resonance (NMR), Simon's Stain, confocal laser scanning microscopy and so forth, were applied to measure interactions of non-cellulosic wall components, cell wall hydrophilicity, and enzyme accessibility to identify key structural features that make agave cell walls less resistant to biological deconstruction when compared to poplar and switchgrass. CONCLUSIONS: This study systematically evaluated the recalcitrant features of agave plants towards biofuels applications. The results show that not only does agave present great promise for feeding biorefineries on semi-arid and arid lands, but also show the value of studying agave's low recalcitrance for developments in improving cellulosic energy crops.
RESUMEN
Nuclear magnetic resonance (NMR) spectroscopy is a well-established analytical and enabling technology in biofuel research. Over the past few decades, lignocellulosic biomass and its conversion to supplement or displace non-renewable feedstocks has attracted increasing interest. The application of solid-state NMR spectroscopy has long been seen as an important tool in the study of cellulose and lignocellulose structure, biosynthesis, and deconstruction, especially considering the limited number of effective solvent systems and the significance of plant cell wall three-dimensional microstructure and component interaction to conversion yield and rate profiles. This article reviews common and recent applications of solid-state NMR spectroscopy methods that provide insight into the structural and dynamic processes of cellulose that control bulk properties and biofuel conversion.