An intrinsically semi-permeable PDMS nanosheet encapsulating adipose tissue-derived stem cells for enhanced angiogenesis.

Cell encapsulation devices are expected to be promising tools that can control the release of therapeutic proteins secreted from transplanted cells. The protein permeability of the device membrane is important because it allows the isolation of transplanted cells while enabling the effectiveness of the device. In this study, we investigated free-standing polymeric ultra-thin films (nanosheets) as an intrinsically semi-permeable membrane made from polydimethylsiloxane (PDMS). The PDMS nanosheet with a thickness of 600 nm showed intrinsic protein permeability, and the device fabricated with the PDMS nanosheet showed that VEGF secreted from implanted adipose tissue-derived stem cells (ASCs) could be released for at least 5 days. The ASC encapsulation device promoted angiogenesis and the development of granulation tissue 1 week after transplantation to the subcutaneous area of a mouse. This cell encapsulation device consisting of PDMS nanosheets provides a new method for pre-vascularization of the subcutaneous area in cell transplantation therapy.

A combination of logical judging circuit and water-resistant ultrathin film PEDOT: PSS electrode for noninvasive ECG measurement.

Heart disease-related deaths have increased in recent decades, with most patients dying of sudden cardiac arrest. In such instances, the effect of regular electrocardiogram (ECG) measurements is minimal. Therefore, long-term ECG monitoring has become increasingly important. In this paper, we report a non-adhesive high accuracy ECG monitoring system that can be used in various scenarios without interfering with daily activities. The ECG ultra-thin film electrode is made by water-resistant material based on poly(3,4-ethylenedioxythiophene) poly(4-styrenesulfonate) (PEDOT: PSS) electrode doped with ethylene glycol (EG) and xylitol, to improve the noise signal caused by sweat. The optimal ratio of the three ingredients of PEDOT: PSS/xylitol/EG was determined experimentally to accommodate the ECG monitoring. By using the proposed selectively closed multi-channel single-lead logic circuit, the noise of ECG signal received from the proposed film electrode can be successfully reduced during broad-area electrode measurements, thus to improve ECG measurement accuracy.

Nanosheet Promotes Chronic Wound Healing by Localizing Uncultured Stromal Vascular Fraction Cells.

Objective: To develop an efficacious and efficient method for treating chronic wounds using "nanosheet" that improves the survival and localization of transplanted cells without prior seeding to optimally derive the regenerative potentials of uncultured stromal vascular fraction (SVF) cells. Approach: We propose a method whereby the wound is covered by uncultured SVF cells using the nanosheet [porous poly(d, l,-lactic acid)] (PDLLA) films) designed to hold cells in a single-cell layer. A chronic wound model was created on 12-month-old db/db mice by inflecting a full-thickness skin excision on their dorsum and was subsequently given either no treatment or a treatment with SVF cells alone (with Tegaderm dressing), nanosheet alone, or nanosheet with SVF cells. Results: The placement of the nanosheet improved the grafted cell retention rate at day 10 timepoint by 5 folds, and the wound area was the smallest in the wounds treated with SVF cells plus nanosheet in comparison to the other groups. Collagen deposition and epidermal growth factor were significantly higher in the wound beds treated with SVF cells with the nanosheet, offering some mechanistic insights. Innovation: Porous poly(d, l,-lactic acid acid) (PDLLA) films or "nanosheet" printed on the nanoscale (1-100 nm in thickness) as a cellular scaffold for cytotherapy for the treatment of chronic wounds. Conclusion: The use of the nanosheet is an effective way to improve the transplanted SVF cell retention and accelerate the overall wound closure.

Porous Polymeric Nanofilms for Recreating the Basement Membrane in an Endothelial Barrier-on-Chip.

Organs-on-chips (OoCs) support an organotypic human cell culture in vitro. Precise representation of basement membranes (BMs) is critical for mimicking physiological functions of tissue interfaces. Artificial membranes in polyester (PES) and polycarbonate (PC) commonly used in in vitro models and OoCs do not replicate the characteristics of the natural BMs, such as submicrometric thickness, selective permeability, and elasticity. This study introduces porous poly(d,l-lactic acid) (PDLLA) nanofilms for replicating BMs in in vitro models and demonstrates their integration into microfluidic chips. Using roll-to-roll gravure coating and polymer phase separation, we fabricated transparent ∼200 nm thick PDLLA films. These nanofilms are 60 times thinner and 27 times more elastic than PES membranes and show uniformly distributed pores of controlled diameter (0.4 to 1.6 µm), which favor cell compartmentalization and exchange of large water-soluble molecules. Human umbilical vein endothelial cells (HUVECs) on PDLLA nanofilms stretched across microchannels exhibited 97% viability, enhanced adhesion, and a higher proliferation rate compared to their performance on PES membranes and glass substrates. After 5 days of culture, HUVECs formed a functional barrier on suspended PDLLA nanofilms, confirmed by a more than 10-fold increase in transendothelial electrical resistance and blocked 150 kDa dextran diffusion. When integrated between two microfluidic channels and exposed to physiological shear stress, despite their ultrathin thickness, PDLLA nanofilms upheld their integrity and efficiently maintained separation of the channels. The successful formation of an adherent endothelium and the coculture of HUVECs and human astrocytes on either side of the suspended nanofilm validate it as an artificial BM for OoCs. Its submicrometric thickness guarantees intimate contact, a key feature to mimic the blood-brain barrier and to study paracrine signaling between the two cell types. In summary, porous PDLLA nanofilms hold the potential for improving the accuracy and physiological relevance of the OoC as in vitro models and drug discovery tools.

Ultraconformable Capacitive Strain Sensor Utilizing Network Structure of Single-Walled Carbon Nanotubes for Wireless Body Sensing.

Capture and real-time recording of precise body movements using strain sensors provide personal information for healthcare monitoring and management. To acquire this information, a sensor that conforms to curved irregular surfaces, including biological tissue, is desired to record complex body movements while acting like a second skin to avoid interference with the movements. In this study, we developed a thin-film-type capacitive strain sensor that is flexible and stretchable on the surface of a living body. We fabricated conductive polymeric ultrathin films ("nanosheets") comprising polystyrene-block-polybutadiene (SB) elastomers and single-walled carbon nanotubes (SWCNTs) (i.e., SWCNT-SB nanosheets) via gravure coating; the SWCNT-SB-coated nanosheets were used as the flexible electrode in a capacitive strain sensor. The dielectric (DE) layer was then prepared using the silicone elastomer Ecoflex 00-30 because its Young's modulus is comparable to that of the epidermis. The normalized capacitance changes (ΔC/C0) in the sensor increased with increasing tensile strain over a range from 0-100%, indicating that the proposed sensor can measure the strain of biological movements, including those of skin and blood vessels. To improve sensor conformability further, the effect of sensor thickness on the gauge factor (GF) was investigated using thinner DE layers by focusing on their flexural rigidity. As a result, the GF increased from 0.64 to 1.13 as the DE layer thickness decreased from 260 to 40 µm. Finally, we evaluated the fabricated sensor's signal stability and mechanical durability, including during wireless sensing when applied to human skin and a vascular model. The ΔC/C0 values varied in response to the bending motion of a finger, dilation of a blood vessel, and the swallowing movement of the throat. These results indicate that our capacitive strain sensor is conformable and functional on biological tissue to enable monitoring of dynamic biological movements (e.g., pulse rate and arterial dilation) without wearer discomfort.

UV laser-processed microstructure for building biohybrid actuators with anisotropic movement.

Fabrication of a biohybrid actuator requires muscle cells anisotropically aligned in a line, curve, or combination of lines and curves (similar to the microstructure of living muscle tissue) to replicate lifelike movements, in addition to considering the arrangement of skeletal structure or muscular structure with anisotropic straight patterns. Here, we report a UV laser-processed microstructure for freely directing cellular alignment to engineer a biohybrid actuator composed of poly(styrene-block-butadiene-block-styrene triblock copolymer) (SBS) thin film with tailor-made microgrooves (MGs) and skeletal myotubes aligned along these MGs. Specifically, straight, circular, or curved MGs were transferred to SBS thin films from a UV laser-processed template, allowing for the successful alignment of myotubes along MGs. The biohybrid actuator, composed of anisotropically aligned myotubes on a curved microgrooved SBS thin film, was contracted by electrical stimulation. Contraction of biohybrid actuators with curved aligned myotubes permits twisted-like behavior, unlike straight microgrooved films. Therefore, the UV laser-ablation system is a unique maskless and rapid microfabrication technique that provides intriguing opportunities for omni-directional microgrooved structures to achieve the complex motion of living organisms.

Molecularly Imprinted Polymer-Based Sensors for the Detection of Skeletal- and Cardiac-Muscle-Related Analytes.

Molecularly imprinted polymers (MIPs) are synthetic polymers with specific binding sites that present high affinity and spatial and chemical complementarities to a targeted analyte. They mimic the molecular recognition seen naturally in the antibody/antigen complementarity. Because of their specificity, MIPs can be included in sensors as a recognition element coupled to a transducer part that converts the interaction of MIP/analyte into a quantifiable signal. Such sensors have important applications in the biomedical field in diagnosis and drug discovery, and are a necessary complement of tissue engineering for analyzing the functionalities of the engineered tissues. Therefore, in this review, we provide an overview of MIP sensors that have been used for the detection of skeletal- and cardiac-muscle-related analytes. We organized this review by targeted analytes in alphabetical order. Thus, after an introduction to the fabrication of MIPs, we highlight different types of MIP sensors with an emphasis on recent works and show their great diversity, their fabrication, their linear range for a given analyte, their limit of detection (LOD), specificity, and reproducibility. We conclude the review with future developments and perspectives.

Bioprinting and biomaterials for dental alveolar tissue regeneration.

Three dimensional (3D) bioprinting is a powerful tool, that was recently applied to tissue engineering. This technique allows the precise deposition of cells encapsulated in supportive bioinks to fabricate complex scaffolds, which are used to repair targeted tissues. Here, we review the recent developments in the application of 3D bioprinting to dental tissue engineering. These tissues, including teeth, periodontal ligament, alveolar bones, and dental pulp, present cell types and mechanical properties with great heterogeneity, which is challenging to reproduce in vitro. After highlighting the different bioprinting methods used in regenerative dentistry, we reviewed the great variety of bioink formulations and their effects on cells, which have been established to support the development of these tissues. We discussed the different advances achieved in the fabrication of each dental tissue to provide an overview of the current state of the methods. We conclude with the remaining challenges and future needs.

Survey of oligoethylene glycol-based self-assembled monolayers on electrochemical aptamer-based sensor in biological fluids.

The ability to monitor levels of endogenous markers and clearance profiles of drugs and their metabolites can improve the quality of biomedical research and precision with which therapies are individualized. Towards this end, electrochemical aptamer-based (EAB) sensors have been developed that support the real-time monitoring of specific analytes in vivo with clinically relevant specificity and sensitivity. A challenge associated with the in vivo deployment of EAB sensors, however, is how to manage the signal drift which, although correctable, ultimately leads to unacceptably low signal-to-noise ratios, limiting the measurement duration. Motivated by the correction of signal drift, in this paper, we have explored the use of oligoethylene glycol (OEG), a widely employed antifouling coating, to reduce the signal drift in EAB sensors. Counter to expectations, however, when challenged in 37 °C whole blood in vitro, EAB sensors employing OEG-modified self-assembled monolayers exhibit both greater drift and reduced signal gain, compared with those employ a simple, hydroxyl-terminated monolayer. On the other hand, when EAB sensor was prepared with a mix monolayer using MCH and lipoamido OEG 2 alcohol, reduced signal noise was observed compared to the same sensor prepared with MCH presumably due to improved SAM construction. These results suggest broader exploration of antifouling materials will be required to improve the signal drift of EAB sensors.

Latest developments in engineered skeletal muscle tissues for drug discovery and development.

INTRODUCTION: With the advances in skeletal muscle tissue engineering, new platforms have arisen with important applications in biology studies, disease modeling, and drug testing. Current developments highlight the quest for engineering skeletal muscle tissues with higher complexity . These new human skeletal muscle tissue models will be powerful tools for drug discovery and development and disease modeling. AREAS COVERED: The authors review the latest advances in in vitro models of engineered skeletal muscle tissues used for testing drugs with a focus on the use of four main cell culture techniques: Cell cultures in well plates, in microfluidics, in organoids, and in bioprinted constructs. Additional information is provided on the satellite cell niche. EXPERT OPINION: In recent years, more sophisticated in vitro models of skeletal muscle tissues have been fabricated. Important developments have been made in stem cell research and in the engineering of human skeletal muscle tissue. Some platforms have already started to be used for drug testing, notably those based on the parameters of hypertrophy/atrophy and the contractibility of myotubes. More developments are expected through the use of multicellular types and multi-materials as matrices . The validation and use of these models in drug testing should now increase.

Angiogenic efficacy of ASC spheroids filtrated on porous nanosheets for the treatment of a diabetic skin ulcer.

Stem cell transplantation is expected to be an effective treatment for intractable skin ulcers by promoting angiogenesis; however, it is challenging to quickly realize a sufficient bloodstream for the ulcers. For this treatment, sheet-like materials with monolayer cells such as cell sheets have been investigated. However, they have a limitation of cell number that can be transplanted at one time due to the two-dimensional, monolayer cell structure, and sufficient secretion of growth factors cannot be expected. In this regard, cellular aggregates, such as spheroids, can reproduce three-dimensional cell-cell interactions that cause biological functions of living tissues more representative than monolayer cells, which is important to achieving efficient secretion of growth factors. In this study, we focused on free-standing porous polymer ultrathin films ("porous nanosheets") comprising poly(d,l-lactic acid) (PDLLA) and succeeded in developing a spheroid-covered nanosheet, on which more than 1000 spheroids from adipose-tissue derived stem cells (ASCs) were loaded. The porous structure with an average pore diameter of 4 µm allowed for facile filtration and carrying spheroids on the nanosheet, as well as sufficient oxygen and nutrients inflow to the cells. The spheroid-covered nanosheet achieved homogeneous transference of spheroids to a whole skin defect in diabetic model mice. Given the continuous release of vascular endothelial growth factor (VEGF) from the spheroids, the transplanted spheroids promoted healing with more accelerated angiogenesis than a nanosheet with a monolayer of cells. The spheroid-covered nanosheet may be a new regenerative material for promoting intractable skin ulcer healing.

Enhanced cellular engraftment of adipose-derived mesenchymal stem cell spheroids by using nanosheets as scaffolds.

The short survival time of transplanted adipose-derived mesenchymal stem cells (ASCs) is a problem for skin wound healing. Transplantation after the formation of cellular spheroids has been investigated as a promising method for prolonging cellular survival. However, there have been technical restrictions for transplantation of spheroids in clinical practice. Here, we show an effective method for transplantation of ASC spheroids onto skin wounds in order to efficiently cure refractory ulcers. To assist anchoring of spheroids onto skin wounds, we used a 120-nm-thick free-standing film (nanosheet) that has a highly adhesive property. Bioluminescence imaging showed that ASC spheroids carried by the nanosheet survived for 14 days, which is about two-times longer than that previously reported. Wounds treated with a nanosheet carrying ASC spheroids were 4-times smaller than untreated wounds on day 14. This method for transplantation of spheroids could be applied to cell therapy for various refractory skin wounds.

Metronomic photodynamic therapy using an implantable LED device and orally administered 5-aminolevulinic acid.

Metronomic photodynamic therapy (mPDT) is a form of PDT that induces cancer cell death by intermittent continuous irradiation with a relatively weak power of light for a long duration (several days). We previously developed a wirelessly powered, fully implantable LED device and reported a significant anti-tumor effect of mPDT. Considering application in clinical practice, the method used for repeated administrations of photosensitizers required for mPDT should not have a high patient burden such as the burden of transvenous administration. Therefore, in this study, we selected 5-aminolevulinic acid (ALA), which can be administered orally, as a photosensitizer, and we studied the antitumor effects of mPDT. In mice with intradermal tumors that were orally administered ALA (200 mg/kg daily for 5 days), the tumor in each mouse was simultaneously irradiated (8 h/day for 5 days) using a wirelessly powered implantable green LED device (532 nm, 0.05 mW). Tumor growth in the mPDT-treated mice was suppressed by about half compared to that in untreated mice. The results showed that mPDT using the wirelessly powered implantable LED device exerted an antitumor effect even with the use of orally administered ALA, and this treatment scheme can reduce the burden of photosensitizer administration for a patient.

Ultra-thin, transparent, porous substrates as 3D culture scaffolds for engineering ASC spheroids for high-magnification imaging.

Three-dimensional (3D) culture is expected to reproduce biological tissues more representatively than monolayer culture, which is important for in vitro research such as drug screening. Recently, various cell culture substrates for spheroid engineering have been developed based on the prevention of cell adhesion. However, despite the expanded usability these substrates provide, they remain limited in terms of optical microscopy imaging of spheroids with high magnification lenses. This is because almost all substrates generated by nanoimprinting hamper the light passing through them owing to their low optical transparency caused by the thickness and surface structure. In this study, we achieved the preparation of spheroids from adipose-tissue derived stem cells (ASCs) on free-standing porous polymeric ultrathin films ("porous nanosheets") consisting of poly(d,l-lactic acid) (PDLLA) with thickness of 120 nm and average pore diameter of 4 µm. ASCs migrated on the porous nanosheet, leading to the spontaneous organization of spheroids anchored via a cell monolayer. The porous nanosheet also provided more than twice the optical transparency in confocal and holographic microscopy observation compared to conventional nanoimprinted substrates for 3D cell culture (NanoCulture Dish). The internal structure of the organized spheroids could be clearly observed with 40× magnification. In addition, the engineered spheroids showed bioactivities indicated by mRNA expression of fibroblast growth factor (FGF-2) and vascular endothelial growth factor (VEGF). Thus, porous nanosheets offer a unique cell culture substrate, not only for engineering 3D cellular organization from stem cells, but also for imaging detailed structure using light microscopy.

A Coupled FEM-SPH Modeling Technique to Investigate the Contractility of Biohybrid Thin Films.

Biohybrid actuators have the potential to overcome the limitations of traditional actuators employed in robotics, thanks to the unique features of living contractile muscle cells, which can be used to power artificial elements. This paper describes a computational approach for the estimation of the contractile capabilities of skeletal muscle cell-powered biohybrid actuators based on polymeric thin films. The proposed model grounds on the coupling between finite element modeling and smooth particle hydrodynamics. This allows describing the overall condition, including the viscous forces caused by the surrounding liquid medium, in which biohybrid systems are normally immersed. The model is calibrated by analyzing the contractile behavior of polydimethylsiloxane films coupled with skeletal muscle cells, reported in the literature as muscular thin films. Afterward, it is applied to poly (D, L-lactic acid) thin films to explore the behavior of these systems, due to myotubes cultured on them, evaluating the role of thickness, tissue maturation status, and hydrostatic pressure on the contractile performance. These results pave the way toward a novel optimization approach of biohybrid robot design relying on the simulation of all the boundary conditions, thus reducing the need for extensive trial-and-error efforts.

Wet-adhesive, haemostatic and antimicrobial bilayered composite nanosheets for sealing and healing soft-tissue bleeding wounds.

Healing soft-tissue wounds with an irregular, complicated topography in a bleeding environment demands the development of a dressing that is wet-adhesive, haemostatic, and antibacterial. To meet this unmet demand, we designed a flexible nanosheet (~77 nm thick) made of two layers, one is the antibacterial and haemostatic gelatin modified with dopamine (DA) and antimicrobial peptide (AMP) and mixed with Ca2+ ions as coagulation factors, and another is the mechanically strong polycaprolactone (PCL). This flexible nanosheet exhibited robust mechanical strength, continuous and effective adhesion to a topographically irregular tissue surface under a wet condition, and a high platelet adhesion capacity. Moreover, the nanosheet presented a significantly reduced clotting time of 4 min and a high bactericidal rate of nearly 100%. An in vivo evaluation of the nanosheet using both murine dorsal skin and liver models further revealed that the nanosheet could successfully seal and heal the wounds in a bleeding environment, efficiently control haemorrhaging, and exert an excellent antibacterial effect in two weeks. Our work suggests that this nanosheet holds great promise in healing the bleeding soft-tissue wounds for treating acute trauma.

Efficient differentiation and polarization of primary cultured neurons on poly(lactic acid) scaffolds with microgrooved structures.

Synthetic biodegradable polymers including poly(lactic acid) (PLA) are attractive cell culture substrates because their surfaces can be micropatterned to support cell adhesion. The cell adhesion properties of a scaffold mainly depend on its surface chemical and structural features; however, it remains unclear how these characteristics affect the growth and differentiation of cultured cells or their gene expression. In this study, we fabricated two differently structured PLA nanosheets: flat and microgrooved. We assessed the growth and differentiation of mouse primary cultured cortical neurons on these two types of nanosheets after pre-coating with poly-D-lysine and vitronectin. Interestingly, prominent neurite bundles were formed along the grooves on the microgrooved nanosheets, whereas thin and randomly extended neurites were only observed on the flat nanosheets. Comparative RNA sequencing analyses revealed that the expression of genes related to postsynaptic density, dendritic shafts, and asymmetric synapses was significantly and consistently up-regulated in cells cultured on the microgrooved nanosheets when compared with those cultured on the flat nanosheets. These results indicate that microgrooved PLA nanosheets can provide a powerful means of establishing a culture system for the efficient and reproducible differentiation of neurons, which will facilitate future investigations of the molecular mechanisms underlying the pathogenesis of neurological disorders.

Tissue-adhesive wirelessly powered optoelectronic device for metronomic photodynamic cancer therapy.

Metronomic (that is, low-dose and long-term) photodynamic therapy (mPDT) for treating internal lesions requires the stable fixation of optical devices to internal tissue surfaces to enable continuous, local light delivery. Surgical suturing-the standard choice for device fixation-can be unsuitable in the presence of surrounding major nerves and blood vessels, as well as for organs or tissues that are fragile, change their shape or actively move. Here, we show that an implantable and wirelessly powered mPDT device consisting of near-field-communication-based light-emitting-diode chips and bioadhesive and stretchable polydopamine-modified poly(dimethylsiloxane) nanosheets can be stably fixed onto the inner surface of animal tissue. When implanted subcutaneously in mice with intradermally transplanted tumours, the device led to significant antitumour effects by irradiating for 10 d at approximately 1,000-fold lower intensity than conventional PDT approaches. The mPDT device might facilitate treatment strategies for hard-to-detect microtumours and deeply located lesions that are hard to reach with standard phototherapy.

3D Bioprinting in Skeletal Muscle Tissue Engineering.

Skeletal muscle tissue engineering (SMTE) aims at repairing defective skeletal muscles. Until now, numerous developments are made in SMTE; however, it is still challenging to recapitulate the complexity of muscles with current methods of fabrication. Here, after a brief description of the anatomy of skeletal muscle and a short state-of-the-art on developments made in SMTE with "conventional methods," the use of 3D bioprinting as a new tool for SMTE is in focus. The current bioprinting methods are discussed, and an overview of the bioink formulations and properties used in 3D bioprinting is provided. Finally, different advances made in SMTE by 3D bioprinting are highlighted, and future needs and a short perspective are provided.

Ultrathin and Stretchable Rechargeable Devices with Organic Polymer Nanosheets Conformable to Skin Surface.

Ultrathin flexible electronic devices have been attracting substantial attention for biomonitoring, display, wireless communication, and many other ubiquitous applications. In this article, organic robust redox-active polymer/carbon nanotube hybrid nanosheets with thickness of just 100 nm are reported as power sources for ultrathin devices conformable to skin. Regardless of the extreme thinness of the electrodes, a moderately large current density of 0.4 mA cm-2 is achieved due to the high output of the polymers (>10 A g-1 ). For the first time, the use of mechanically robust yet intrinsically soft electrodes and polymer nanosheet sealing leads to the fabrication of rechargeable devices with only 1-µm thickness and even with stretchable properties.