RESUMEN
The dissimilar friction stir lap welding of AA6061-T6 and mild steel using the hemispherical tool tilted towards the retreating side is investigated. Critical defects such as hook features and internal voids are avoided by limiting the plunge depth in the lower plate to a tenth of a millimeter. The low heat generation guaranteed by the hemispherical tool produces a nanoscale intermetallic compound layer alternatively composed of an Al-rich and a ternary Al-Fe-Mg phases. The complex and extremely thin interlayers strengthen the Al-Fe mechanical bonding, guaranteeing high mechanical properties and rupture within the Al-stirred zone. Thermomechanical phenomena governing friction stir lap welding with the hemispherical tool drastically limit the growth of intermetallics, leading to the high mechanical strength of the lap joint.
RESUMEN
The friction stir welding (FSW) process was recently developed to overcome the difficulty of welding non-ferrous alloys and steels. In this study, dissimilar butt joints between 6061-T6 aluminum alloy and AISI 316 stainless steel were welded by FSW using different processing parameters. The grain structure and precipitates at the different welded zones of the various joints were intensively characterized by the electron backscattering diffraction technique (EBSD). Subsequently, the FSWed joints were tensile tested to examine the mechanical strength compared with that of the base metals. The micro-indentation hardness measurements were conducted to reveal the mechanical responses of the different zones in the joint. The EBSD results of the microstructural evolution showed that a significant continuous dynamic recrystallization (CDRX) occurred in the stir zone (SZ) of the Al side, which was mainly composed of the weak metal, Al, and fragmentations of the steel. However, the steel underwent severe deformation and discontinuous dynamic recrystallization (DDRX). The FSW rotation speed increased the ultimate tensile strength (UTS) from 126 MPa at a rotation speed of 300 RPM to 162 MPa at a rotation speed of 500 RPM. The tensile failure occurred at the SZ on the Al side for all specimens. The impact of the microstructure change in the FSW zones was significantly pronounced in the micro-indentation hardness measurements. This was presumably attributed to the promotion of various strengthening mechanisms, such as grain refinement due to DRX (CDRX or DDRX), the appearance of intermetallic compounds, and strain hardening. The aluminum side underwent recrystallization as a result of the heat input in the SZ, but the stainless steel side did not experience recrystallization due to inadequate heat input, resulting in grain deformation instead.
RESUMEN
The grain refinement mechanisms along the material flow path in pure and high-purity Al were examined, using the marker insert and tool stop action methods, during the rapid cooling friction stir welding using liquid CO2. In pure Al subjected to a low welding temperature of 0.56Tm (Tm: melting point), the resultant microstructure consisted of a mixture of equiaxed and elongated grains, including the subgrains. Discontinuous dynamic recrystallization (DDRX), continuous dynamic recrystallization (CDRX), and geometric dynamic recrystallization are the potential mechanisms of grain refinement. Increasing the welding temperature and Al purity encouraged dynamic recovery, including dislocation annihilation and rearrangement into subgrains, leading to the acceleration of CDRX and inhibition of DDRX. Both C- and B/-type shear textures were developed in microstructures consisting of equiaxed and elongated grains. In addition, DDRX via high-angle boundary bulging resulted in the development of the 45° rotated cube texture. The B/ shear texture was strengthened for the fine microstructure, where equiaxed recrystallized grains were fully developed through CDRX. In these cases, the texture is closely related to grain structure development.
RESUMEN
It is known that one of the main concerns associated with the conventional welding of precipitation-strengthened Al alloys is the formation of softening regions, resulting in the deterioration of mechanical properties. In this study, we show that linear friction welding (LFW) can completely suppress softening regions in precipitation-strengthened AA6061-T6 alloy by introducing a large shear strain and by controlling the interfacial temperature. We found that the LFW process resulted in an extremely low interfacial temperature; it decreased as the applied pressure increased from 50 to 240 MPa. This approach can essentially suppress both softening and hardening regions, leading to uniform hardness distribution in Al joints. The high-pressure LFW process demonstrated here can thus provide an innovated guidance to obtain high-performance Al alloy joints and be extended to other precipitation-strengthened Al alloys, which undergo high-temperature softening.
